CC2450E1VH [ETC]
RELAY SSR DUAL 50A ZERO PNL MNT;
| 型号： | CC2450E1VH |
| 厂家： | 
ETC |
| 描述： | RELAY SSR DUAL 50A ZERO PNL MNT |
| 文件： | 总6页 (文件大小：895K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Panel Mount
Datasheet
Evolution Dual Series
• 25A & 50A Output rating per channel @ 40°C
• 24 to 280 & 48 to 600VAC Operating voltage
• 4-32VDC Control input
• Three input termination options
• Zero turn-on outputs
• Input status LED indicator for each channel
• Available with IP20 “Touch-Safe” Covers
• UL508 Endurance Rating
PRODUCT SELECTION
Control Voltage
240V, 25A
240V, 50A
480V, 25A
480V, 50A
4-32 VDC
CD2425W2U
CD2450W2U
CD4825W2U
CD4850W2U
AVAILABLE OPTIONS
Output Terminal
Orientation
U: A channel top,
B channel bottom
V: A channel on left,
B channel on right
Operating Voltage
24: 24-280 VAC
48: 48-600 VAC
Control Voltage
W: 4-32 VDC
Series
C
D
24
25
W
2
V
H
Cover
C: Included
D: Not Included
Rated Load Current
Input Connector
2: Key Locking Connector Blank: Not Included
3: 4 Pin Connector H: Included
Thermal Pad
25: 25 Amps
50: 50 Amps
accepting Screw Terminals
4: 4 Pin Spring Terminal
Required for valid part number
For options only and not required for valid part number
* Not all part number combinations are available.
Contact Crydom Technical support for information on
the availability of a specific part number.
(1)
OUTPUT SPECIFICATIONS
Description
Cx2425xxxx
24-280
0.15-25
600
Cx2450xxxx
24-280
0.15-50
600
Cx4825xxxx
48-600
0.15-25
1200
Cx4850xxxx
48-600
0.15-50
1200
Operating Voltage (47-440Hz) [Vrms]
Load Current Range (3) [Arms]
Transient Overvoltage [Vpk]
Maximum Off-State Leakage Current @ Rated Voltage [mArms]
Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2)
Maximum 1 Cycle Surge Current (50/60) [Apk]
Maximum Surge Current 50Hz (20ms) [Apk]
Maximum On-State Voltage Drop @ Rated Current [Vpk]
Thermal Resistance Junction to Case (Rjc) [°C/W]
Maximum I² t for Fusing 50/60Hz (1/2 cycle) [A² sec]
Minimum Power Factor (with Maximum Load)
1.0
500
275/300
275
1.3
0.65
380/370
0.5
1.0
500
710/750
710
1.3
0.33
2520/2320
0.5
1.0
500
275/300
275
1.3
0.65
380/370
0.5
1.0
500
710/750
710
1.3
0.33
2520/2320
0.5
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
INPUT SPECIFICATIONS(1)
Description
Control Voltage Range
CxxxWxxx
4-32 VDC
Minimum Turn-On Voltage
Minimum Turn-Off Voltage
Typical Input Current
Nominal Input Impedance
Maximum Turn-On Time [msec]
Maximum Turn-Off Time [msec]
4 VDC
1 .0 VDC
10 mA @ 12 VDC
See Note (4)
1/2 Cycle
1/2 Cycle
GENERAL SPECIFICATIONS
Description
Dielectric Strength, Input/Output (50/60Hz)
Dielectric Strength, Input/Output/Base (50/60Hz)
Minimum Insulation Resistance (@ 500 V DC)
Parameters
4000 Vrms
4000 Vrms
9
10 Ohm
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range
Ambient Storage Temperature Range
Weight (typical)
10 pF
-40 to 80 °C
-40 to 125 °C
3.0 oz (86.5 g)
Terminals
Max. Torque
Max. Wire Size
Screw Type Output: 8-32
Output: 20 in lb (2.2Nm)
Output:2 x AWG 8 (3.8mm)
GENERAL NOTES
1) All parameters at 25°C and per section unless otherwise specified.
2) Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
3) Heat sinking required, see derating curves.
4) Input circuit incorporates active current limitation
WIRING DIAGRAM
SSR Output Configuration
"U" Option Top-Bottom
Line/Load Connections
LOAD A
AC SUPPLY
1
A1
AC
-DC
LED
Trigger
Circuit
+DC
2
3
A2 AC
Current
Limiter
+A
A
-A
+B
B
-B
B1
AC
-DC
LED
Trigger
Circuit
+DC
4
B2 AC
Current
Limiter
AC SUPPLY
LOAD B
Contactor Output Configuration
"V" Option Left-Right
Line/Load Connections
+A
-A
A
B
+B
-B
L
O
A
D
L
O
A
D
A
B
AC SUPPLY
AC SUPPLY
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
MECHANICAL SPECIFICATIONS
Tolerances: ꢀ0ꢀꢁ ꢂn ꢃ ꢀ0. ꢄ
All dꢂꢄensꢂons are ꢂn: ꢂnches [ꢄꢂllꢂꢄeters]
Mounting
Hole/Slot
r 0.09 [2.2]
2.300 [58.42]
Mounting
Hole/Slot
0.18 [4.5]
DIA.
1.875 [47.63]
.625 [15.89]
8X .191 [4.85]
1.100 [27.94]
IP20
1.425 [36.20]
.803 [20.40]
1.700 [43.18]
2.635 [66.93]
2X .200 [5.08]
1.800 [45.72]
2.300 [58.42]
1.100 [27.94]
IP00
1.150 [29.21]
.803 [20.40]
1.150 [29.21]
1.700 [43.18]
1.800 [45.72]
MECHANICAL DIMENSIONS
(shown without IP20 cover)
INPUT CONNECTOR DIMENSIONS
SUGGESTED MATING
CONNECTORS/PLUGS
3X 0.100 [2.54]
4X 0.026 [0.66]
(SQUARE)
Crimp Housing, Positive Latch
Molex 050579404
1.150 [29.21]
0.200 [5.08]
0.300 [7.62]
Accepts wires: AWG #24, 0.2 mm²
0.120 [3.05]
0.420 [10.67]
INPUT CONNECTOR
OPTION 2
0.500 [12.71]
Vertical Plug, Top Wire entry
Molex 039500-0004
Phoenix 1840382
Dinkle EC350V-04P
0.413 [10.50]
Vertical Plug, Rear Wire entry
Molex 39503-2004
3X 0.138 [3.50]
Phoenix 1862878
Dinkle EC350RL-04P
0.157 [4.00]
1.059 [26.90]
1.046 [26.58]
0.285 [7.25]
Vertical Plug, Front Wire entry
Molex 39503-3004
Phoenix 1863178
4X 0.031 [0.80]
(SQUARE)
0.122 [3.10]
INPUT CONNECTOR
0.606 [15.40]
Dinkle EC350R-04P
OPTION 3
Vertical Spring Cage Plug, top Wire E
Phoenix 1939934
Dinkle 0221-2004
All 4 options accept wires: AWG #16 to 24
N/A
Accepts wires: AWG #16 to 24
1.201 [30.50]
INPUT CONNECTOR
OPTION 4
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
THERMAL DERATE INFORMATION
CXXX25XXXX
CXXX50XXXX
(25 Amps per Channel)
(50 Amps per Channel)
50
40
30
20
10
0
100
80
60
40
20
0
20
30
40
50
60
70
80
20
30
40
50
60
70
80
Ambient Temperature [°C]
Ambient Temperature [°C]
1.0°C/W - HS103
1.5°C/W - HS-2
2.5°C/W -
0.5°C/W - HS053
1.0°C/W - HS103
1.5°C/W - HS-2
AGENCY APPROVALS
Approvals
Designed in accordance with the requirements of IEC 62314
E116950
Rev. 060916
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
RISQUE DE
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSI
ONE.
存在电击、
爆炸或电弧
闪烁危险
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•
在操作此设
备之前请先
关闭电源。
• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
• Disconnect all
power before
installing or
working with
this equipment.
• Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
• Spenga tutta
l'alimentazion
e che fornisce
questa
apparecchiatu
ra prima del
若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。
con este equipo.
• Verify all
connections
and replace all
covers before
turning on
Gerät Arbeiten
durchführen
lavorare a questa
• Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
apparecchiatu ra
• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
• Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima della
• Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
power.
el equipo.
Failure to follow
these
instructions will
result in death
or serious injury.
El
rotazione
sull'alimentazi one
Abdeckungen
ersetzen.
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
L'omissione di
seguire queste
istruz ioni
provocherà la
morte o di
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
lesioni serie
Verletzungen
führen.
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Fremdkörper in das Produkt ein.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
材料损坏和高温外壳的危险性
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• 产品的一侧面板可能很热，在其冷却前请
不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr (VI))
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
部件
名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
半导体芯片
焊接点
50
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明