DR2260A20VR [ETC]
RELAY SSR 600V 20A DIN RAIL;型号: | DR2260A20VR |
厂家: | ETC |
描述: | RELAY SSR 600V 20A DIN RAIL |
文件: | 总8页 (文件大小:1006K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DIN Rail Mount
Datasheet
DR22 Series
AC Output DIN Rail Mount SSRs
• Output ratings up to 35 Amps at 600 VAC
• Built-in overvoltage protection
• Relay or Contactor configuration
• Integral heat sink eliminates the need for complex thermal calculations
• DBC substrate for superior thermal performance
• "Elevator" screw option to allow the use of ring or lug type terminals
• IP20 touch-safe housing
• AC or DC control
• C-UL-US and TUV approved
PRODUCT SELECTION
Control Voltage
90-280 VAC/VDC
4-32 VDC
20A
DR2260A20x
DR2260D20x
30A
DR2260A30x
DR2260D30x
35A
DR2260A35x
DR2260D35x
AVAILABLE OPTIONS
Rated Load Current
20: 20 Amps
Switching Type
Blank: Zero Voltage Turn-On
R: Instantaneous Turn-On
(Motor Rating Certified)
30: 30 Amps
Operating Voltage
60: 48-600 VAC
35: 35 Amps [High I2t]
Series
DR22
60
A
20
V
R
J
Control Voltage (1)
Terminal Layout
U: Relay Configuration
V: Contactor Configuration J: Spring Terminal
Input Connector
A: 90-280 VAC/VDC
D: 4-32 VDC
Blank: Screw Terminal
(std. screw)
(V and W suffixes only)
W: Contactor Configuration
(elevator screw)
Required for valid part number
For options only and not required for valid part number
OUTPUT SPECIFICATIONS (2)
Description
Operating Voltage (47-440Hz) [VRMS]
20A
48-600
1200
30A
48-600
1200
35A
48-600
1200
Transient Overvoltage [Vpk] (3)
Maximum Off-State Leakage Current @ Rated Voltage [mARMS]
Minimum Off-State dV/dt @ Maximum Rated Voltage [V/μsec]
Load Current, General Use UL508/LC A IEC62314 @ 40°C [ARMS]
Load Current, Motor Starting UL508 FLA/LC B IEC62314 @ 40°C [ARMS]
Minimum Load Current [mARMS]
1
500
20
8.5/4.8
100
1
500
30
14/7.6
100
1
500
35
26/14
150
Maximum 1 Cycle Surge Current (50/60Hz) [Apk]
Maximum On-State Voltage Drop @ Rated Current [Vpk]
Maximum 1/2 Cycle I² t for Fusing (50/60Hz) [A² sec]
Minimum Power Factor (at Maximum Load) (4)
Motor Rating UL 508/IEC62314 [HP (kW)]: 120 VAC
Motor Rating UL 508/IEC62314 [HP (kW)]: 240 VAC
Motor Rating UL 508/IEC62314 [HP (kW)]: 480 VAC
286/300
1.35
409/375
0.5
0.5 (0.37)
1.5 (1.1)
3 (2.24)
716/750
1.35
2563/2343
0.5
1 (0.74)
3 (2.2)
5 (3.7)
1290/1350
1.3
8320/7593
0.5
2 (1.5)
5 (3.73)
10 (7.4)
(2)
INPUT SPECIFICATIONS
Description
DR2260Dxxx
DR2260Axxx
Control Voltage Range
4-32 VDC (5)
-32 VDC
90-280 VAC/VDC (6)
Maximum Reverse Voltage
Minimum Turn-On Voltage
Must Turn-Off Voltage
-
90 VAC/VDC
5 VAC/VDC
6 mA
4 VDC
1 VDC
7 mA
Minimum Input Current (for on-state)
Maximum Input Current
15 mA
10 mA
Nominal Input Impedance
Maximum Turn-On Time [msec]
Maximum Turn-Off Time [msec]
Current Limited
1/2 Cycle (7)
1/2 Cycle
Current Limited
20
30
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
GENERAL SPECIFICATIONS (2)
Description
Dielectric Strength, Input to Output (50/60Hz)
Dielectric Strength, Input/Output to Case (50/60Hz)
Minimum Insulation Resistance (@ 500 VDC)
Parameters
4000 VRMS
4000 VRMS
109 Ohms
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range (8)
Ambient Storage Temperature Range
Short Circuit Current Rating (9)
Weight (typical)
8 pF
-40 to 80 °C
-40 to 100 °C
100kA
Option “U” 10.5 oz (298 g), Option “V”,“W” 10.6 oz (301 g)
Housing Material
UL94 V-0
Heat Sink Material
Din Rail Clip Material
Aluminum
Zink Plated Steel
Hardware Finish
Nickel Plating
Input Terminal Screw Torque Range (lb-in/Nm)
Load Terminal Screw Torque Range (lb-in/Nm)
Humidity
Option “U” 13-15/1.5-1.7, Option “V”,“W” 5/0.5 (10)
Option “U” 13-15/1.5-1.7, Option “V”,“W” 18-20/2-2.2
95% non-condensing
LED Input Status Indicator
Green
INPUT CURRENT INFORMATION
4-32 VDC Input
90-280 VAC/VDC Input
14
12
10
8
7
6
5
4
3
2
1
0
6
4
2
0
0
5
10
15
20
25
30
35
0
40
80
120
160
200
240
280
Input Voltage (VAC/VDC)
Input Voltage (VDC)
SURGE CURRENT INFORMATION
DR2260x20x
DR2260x30x
300
700
600
500
400
300
200
100
250
200
150
100
50
0
0
0.01
0.1
1
10
0.01
0.1
1
10
(sec)
(sec)
Surge Duration
Surge Duration
DR2260x35x
1400
1200
1000
800
600
400
200
0
Single Pulse (11)
0.01
0.1
1
10
(sec)
Surge Duration
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
THERMAL DERATE INFORMATION(8)
DR2260x20x
DR2260x30x
DR2260x35x
Single unit (12)
Single unit (12)
Multiple units
Single unit (12)
Multiple units
Multiple units
20
15
10
5
30
25
20
15
10
5
35
30
25
20
15
10
5
0
0
0
20
30
40
50
60
70
80
20
30
40
50
60
70
80
20
30
40
50
60
70
80
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Ambient Temperature (ºC)
EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAM
DC Control
+3/A1
Load
1/L1
A
+
-
Trigger
Circuit
V
V
AC
DC
B
Load
-4/A2
2/T1
Current
Limiter
Load can be wired in position A or B
AC/DC Control
Current
Limiter
Load
A
+3/A1
1/L1
+/
AC/DC
Converter
Trigger
Circuit
AC/DC
V
V AC
-/
B
Load
-4/A2
2/T1
Load can be wired in position A or B
Recommended Wire Sizes
Wire Size
Terminal
Configuration
Wire Pull-Out
Strength (lb)[N]
(Solid / Stranded)
2
2 x 18 AWG (1 mm ) Stranded
20 [88]
60 [266]
20 [88]
Output (13)
Relay “U” suffix
2
2 x 10 AWG (6 mm ) Stranded
2
2 x 18 AWG (1 mm ) Stranded
Input
Relay “U” suffix
2
2 x 12 AWG (4 mm ) Stranded
40 [177]
25 [111]
80 [355]
90 [400]
4.5 [20]
30 [133]
4 [18]
2
Output
Contactor
“V” &“W”
suffixes
2 x 20 AWG (0.75 mm ) [minimum]
2
2 x 10 AWG (6 mm )
2
2 x 8 AWG (10 mm ) [maximum]
2
30 AWG (0.05 mm ) [minimum]
Input
Screw
Spring
2
12 AWG (3.3 mm ) [maximum]
Contactor
“V” &“W”
suffixes
2
26 AWG (0.13 mm ) [minimum]
2
12 AWG (3.3 mm ) [maximum]
30 [133]
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
MECHANICAL SPECIFICATIONS
Tolerances: ±±0±ꢀ ꢁn ꢂ ±0. ꢃꢃ
All dꢁꢃensꢁons are ꢁn: ꢁnches [ꢃꢁllꢁꢃeters]
Contactor Configuration
1087
[470.]
1ꢂL1
Input Connector
Screw
Terminal
306ꢀ
[9109]
30.4
[9±]
ꢀ08.
[7ꢀ03]
1088
[4708]
+3ꢂA1 -4ꢂAꢀ
Spring
Terminal
ꢀꢂT1
1019
[3±0ꢀ]
±089
[ꢀꢀ0.]
40.9
[1160.]
Protective Earth Connection
Relay Configuration
±039
[909]
INPUT
+3ꢂA1
-4ꢂAꢀ
3067
[930ꢀ]
30±±
[760ꢀ]
1088
[4708]
30.4
[9±]
1±-3ꢀ
Thread
Protective Earth (PE) screw type recommended is
10-32 UNC standard not provided with SSR. Through
the use of a DIN rail ground (protective conductor)
terminal block, the DIN rail itself can be used as the
grounding bus bar. In this case, the zinc plated steel
material used for the DIN rail clip of DR22 models,
permits a secure path to ground and avoid the need of
a further PE connection.
1ꢂL1
ꢀꢂT1
OUTPUT
1019
[3±0ꢀ]
±089
[ꢀꢀ0.]
40.9
[1160.]
Elevator Screw (Suffix ‘W’)
TABLE 1. Compatible Terminals
W
D
W D
Terminals
Fork Lug
Ring Lug
Copper Lug
Copper Lug
TRM±
TRM6
Crydom Part No.
Width [W] in (mm)
Stud Size Dia [D] (in)
Wire Size AWG
±04. (1104)
#8 (±0168)
±04. (1104)
#8 (±0168)
The Elevator Screw optꢁon allows the screw and
claꢃp to be raꢁsed out of the ꢃatꢁng threads
coꢃpletely0 Thꢁs provꢁdes for the ꢁnsertꢁon and
use of a rꢁng or lug type wꢁre terꢃꢁnal0 Refer to
TABLE 1 for Coꢃpatꢁble Terꢃꢁnals0
6-±
14-6
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
ACCESSORIES
Recommended Accessories
New Accessories!
Connectors
Part number: CP201, CP202
Pluggable input connectors, 2 position, with screw terminals (CP201) or
spring type terminals (CP202). Compatible with Contactor Configuration
NOVA22 SSRs.
Connectors
ID Marker
Lug Terminal
CP201
CP202
CNLB
CNLN
CNL2
TRM0
TRM6
Lug Terminal
Part number: TRM0
Copper wire lug for AWG 6 (13.3 mm²) to AWG 0 (53.5 mm²) wire size. For
use with "Elevator" screw option ("W" suffix) NOVA22 SSRs.
AGENCY APPROVALS, CONFORMANCES AND EMC
(14)
E116949
E116949
Certification in accordance with:
United States Standard for Industrial Control Equipment - UL 508 and
Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14.
TUV Certified in accordance to EN62314
(15)
Vibration Resistance:
IEC 60068-2-6: Amplitude Range 10-500 Hz, Displacement 0.75mm
(15)
Shock Resistance:
IEC 60068-2-27: Peak Acceleration 50g, Duration11ms.
Electromagnetic Compatibility
Generic
Standard
Inmunity Tests
Test Specification
Level
Performance
Electrostatic Discharge
IEC 61000-4-2
8kV air discharge
6kV contact discharge
Criterion B
Criterion A
Fast transients (burst)
IEC 61000-4-4
Output
Input
2kV, 5kHz, 100kHz Criterion B
1kV, 5kHz, 100kHz Criterion B
IEC 61000-6-2
Immunity for
Industrial
Surge
1kV Line to Line
2kV Line to Earth Criterion B
Criterion B
2kV Line to Earth Criterion B
Criterion B
Environments
Output
IEC 61000-4-5
AC Input 1kV Line to Line
Option
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
GENERAL NOTES
(1) Control voltage 18-52 VAC/VDC is available upon request.
(2) All parameters at 25°C unless otherwise specified.
(3) Output will self trigger between 900-1200 Vpk, not suitable for capacitive loads.
(4) High inductive loads requires nominal control voltage; AC input models only.
(5) Increase minimum voltage by 1 V for operations from -20 to -40°C.
(6) For ambient temperatures above 40°C the maximum control voltage must not exceed 250 VAC/VDC.
(7) Turn-on time for Instantaneous turn-on versions is 0.1 msec.
(8) AC input models operating range is -20 to 60 °C.
(9) When protected with the appropriate class and rated fuse. For detailed info please contact Crydom Technical Support.
(10) Input torque only for contactor (V,W) with screw terminals Connector.
(11) For single surge pulse Tc=25°C; Tj=125°C. For AC Output SSRs, AC RMS value of surge current equals the peak value divided by √2 (1.414).
(12) Minimum spacing to obtain max. current is 22.5mm between adjacent units.
(13) For 35 Amp Relay (”U”) layout models, use Pin Terminals (L 0.410 in x Ø 0.102 in) to install 8 AWG wire.
(14) Applicable to Relay (”U”) option.
(15) Test made with a unit fixed between DIN RAIL Stoppers. Multiple devices mounted close each other, results may vary.
Rev. 101619
ECN#20785
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
RISQUE DE
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
存在电击、
爆炸或电弧
闪烁危险
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•
在操作此设
备之前请先
关闭电源。
• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
• Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
• Disconnect all
power before
installing or
working with
this equipment.
• Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
若不遵守这些说明,
可能会导致严重的
人身伤害甚至死亡。
con este equipo.
• Verify all
connections
and replace all
covers before
turning on
Gerät Arbeiten
durchführen
apparecchiatura
• Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
• Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
• Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
power.
el equipo.
Failure to follow
these
instructions will
result in death
or serious injury.
dell’accensione
El
Abdeckungen
ersetzen.
L'omissione di
queste istruzioni
provocherà la
morte o
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
lesioni serie
Verletzungen
führen.
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Fremdkörper in das Produkt ein.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
材料损坏和高温外壳的危险性
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• 产品的一侧面板可能很热,在其冷却前请
不要触碰。
• 遵照正确的安装说明,包括扭矩值。
• 请勿让液体及其他异物进入本产品。
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
如不能正确执行这些操作说明,
极有可能造成严重人体伤害或者设备的损坏。
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
DIN Rail Mount
Datasheet
ANNEX - ENVIRONMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr (VI))
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
部件
名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
半导体芯片
焊接点
50
Do not forget to visit us at: www.crydom.com
Copyright © 2019 Crydom Inc. Specifications subject to change without notice.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明