JCUHLATN-2.048MHZ [ETC]
Voltage-Controlled Oscillator ; 压控振荡器\n型号: | JCUHLATN-2.048MHZ |
厂家: | ETC |
描述: | Voltage-Controlled Oscillator
|
文件: | 总8页 (文件大小:116K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Product Data Sheet
J-Type
Voltage Controlled Crystal Oscillator
Features
• Output Frequencies from 1.024 MHz to 170.000 MHz
• +3.3 or +5.0 volt options
• Small 14mm x 9mm J-type Package
• CMOS or PECL Outputs
• Low phase noise and custom options
• 0/70° C or –40/85° C operating temperature
• Tri-State output (CMOS) Enable/Disable (PECL)
Applications
• Clock Smoothing
• Frequency Translation
• SONET, SDH, ATM, DSLAM, ADM
Description
The J-type voltage controlled crystal oscillator incorpo-
rates VI’s advanced VCXO performance capabilities
while adhering to a package footprint compatible with
the industry-common J-lead package.
The J-type VCXO is a quartz stabilized square wave
generator with either a CMOS output for driving
CMOS/TTL loads or a PECL output. The device is pack-
aged in a 6 pin J-lead ceramic package and is hermeti-
cally sealed with a grounded conductive lid.
J-Type Voltage Controlled Crystal Oscillator
CMOS Output Option
Electrical Performance @ 25°C for the CMOS output option
Parameter
Supply Voltage1, +5 volt option
+3.3 volt option
Symbol
Minimum
Typical
Maximum
Unit
Vdc
Vdc
4.5
3.0
5.0
3.3
5.5
3.6
Supply Current
10mA + 0.25mA per MHz, typical
Center Frequency, see ordering information
Operating Temperature, see ordering info
FN
1.024
77.760
MHz
°C
TOP
APR
0/70, -40/85
±50 to ±100
Absolute Pull Range over the operating tempera-
ture range, aging and power supply Vc=0.5 to
4.5 at 5V supply or 0.3 to 3.0 V at 3.3V supply
see ordering information for options
ppm
Gain Transfer
(Frequency vs. Control Voltage)
KV
Positive
Output Level High2
Output Level Low2
Output Rise/Fall Time2
Duty Cycle3, see ordering info
VOH
VOL
tR/ tF
SYM
IL
0.8*Vcc
-
-
V
V
0.1*Vcc
5
ns
%
45/55 or 40/60
Control Input Leakage
1
-
uA
kHz
ps
ps
Control Voltage Modulation Bandwidth
RMS Jitter, Output=12.0-77.760 MHz
BW
-
10
3
RMS Jitter, Output=12.0-77.760 MHz.
Band=12.0 KHz - 20 MHz
<0.5
Control Range
0
VDD
7
Maximum Supply Voltage
Storage Temperature
Soldering Temp./Time
V
TS
-55
-
-
-
125
°C
TLS
220/10
°C/s
1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended.
2. Figure 1 defines these parameters. Figure 2 illustrates the load used to test devices.
3. Duty cycle is defined as on-time versus period at 1.4 V for TTL, and 2.5 V for CMOS (5volt supply) and at 1.65 V for CMOS (3.3 volt operation)
Pin Out Information for the CMOS output option
Pin
1
Symbol
Vc
Function
VCXO Control Voltage.
2
Tri-State1
TTL logic low disables output
TTL logic high, or no connect, enables output
3
4
5
GND
Case and electrical ground.
VCXO Output
Output
CMOS/TTL
select1,2
TTL logic low optimizes symmetry for CMOS
TTL logic high, or NC, optimizes symmetry for TTL.
6
VCC
Power Supply Voltage (5.0 V or 3.3V ±10%)
1. Standard option. Tri-State can be connected to pin 5 and CMOS/TTL select would be on pin 2.
2. Output is HCMOS. For frequencies >12MHz, this option optimizes symmetry for either CMOS or TTL thresholds. Ground this pin for fre-
quencies < 12MHz.
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
2
J-Type Voltage Controlled Crystal Oscillator
CMOS Output Option
Figure 1
Figure 2
Output Wave Form
Output Test Conditions
Output Test Conditions (25±5°C) for 5 volt devices.
For 3.3V use 15pF cap only, no resistors needed.
Threshold = 1.4 volts for TTL
and 50% for CMOS
Ordering Information for the CMOS output option (add frequency)4
Package
Supply
Voltage
VCXO
Type
APR
(ppm)
Operating
Temp.
(°C)
Output/Duty
Cycle
Min/Max
Tri-State
Specials
J
6 pin
Ceramic
SOJ
C
D
5V±10%
U
VCXO G
±50
±80
C
L
0/70
A
J
TTL/
T Tri State
on pin 2
N
Standard
CMOS
45/55%1
3.3V±10% L
±10%
N
H
-40/85
CMOS
linear
45/55%2
VCXO
±100
K
CMOS
40/60%3
1. Output is CMOS and symmetry is tested at TTL and CMOS thresholds.
2. Output is CMOS and symmetry is tested at CMOS threshold. This option is used for 3.3 V operation.
3. Output is CMOS and symmetry is tested at CMOS thresholds. This option is required for 3.3V, frequencies >51.840MHz.
4. Note: Not all combinations are possible.
Example: JDUGCKTN @ 77.76 MHz = 3.3 volt, VCXO@77.760, ±50 ppm APR, 0/70°C, 40/60% Symmetry,
CMOS, Tri-State on pin 2.
Standard Frequencies, in MHz, for CMOS output option
1.024
3.686
1.544
4.000
2.000
4.032
2.048
4.096
3.088
4.434
3.580
5.000
6.144
6.176
6.312
6.400
8.000
8.192
8.448
14.318
19.44
27.000
38.880
52.000
10.000
15.360
20.000
30.000
40.000
65.536
12.000
15.440
20.480
32.000
40.960
77.760
12.288
16.000
24.000
32.768
44.736
155.5201
12.352
16.384
24.576
34.368
50.000
13.000
18.432
24.704
35.328
51.840
1. Uses a PLL multiplier, jitter is 25ps rms typical vs 3ps rms typical for a HFF (High Frequency Fundemental) design. Available with 5 Vdc input only.
Other frequencies available upon request.
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
3
J-Type Voltage Controlled Crystal Oscillator
PECL Output Option
Electrical Performance @ 25°C for the PECL output option
Parameter
Supply Voltage1, +5 volt option
+3.3 volt option
Symbol
Minimum
Typical
Maximum
Unit
Vdc
Vdc
4.5
3.0
5.0
3.3
5.5
3.6
Supply Current (frequency dependent)
Center Frequency, see ordering information
Operating Temperature, see ordering info
<65mA
170
FN
15
MHz
°C
TOP
APR
0/70, -40/85
±32 to ±50
Absolute Pull Range over the operating tempera-
ture range, aging and power supply Vc= 0.5 to
4.5 at 5V supply or 0.3 to 3.0 V at 3.3 supply
see ordering information for options
ppm
Gain Transfer
(Frequency vs. Control Voltage)
KV
Positive
Output Level High2 (0/70°C)
Output Level Low2 (0/70°C)
Output Level High2 (-40/+85°C)
Output Level Low2 (-40/+85°C)
Output Rise/Fall Time2
VOH
VOL
VOH
VOL
tR/ tF
SYM
IL
Vcc-1.025
Vcc-1.810
Vcc-1.085
Vcc-1.830
-
-
-
-
Vcc-0.880
Vcc-1.620
Vcc-0.880
Vcc-1.555
1
V
V
V
V
ns
%
Duty Cycle
45/55
Control Input Leakage
0.1
mA
kHz
ps
ps
Control Voltage Modulation Bandwidth
RMS Jitter
BW
10
see ordering information
RMS Jitter, 155.52 MHz, 12 kHz to 20 MHz (option P)
Maximum Control Voltage
Maximum Supply Voltage
Storage Temperature
0.5
1.0
VDD
7
0
V
TS
-55
-
-
-
125
°C
Soldering Temp./Time
TLS
220/10
°C/s
1. Power supply bypass is required and a 0.1uF in parallel with a 0.01uF high frequency capacitor is recommended.
2. Transition times are measured from 20% to 80% of a full 10K ECL level swing.
Pin Out Information for the PECL output option
Pin
1
Symbol
Vc
Function
VCXO Control Voltage.
2
N/C or E/D1
No Connect or Output Disable option
Case and electrical ground.
VCXO Output
3
GND
4
Output
COutput
VCC
5
VCXO Complementary Output
Power Supply Voltage (5.0 V or 3.3V ±10%)
6
1. By setting pin 2 high, the outputs are disabled and output on pin 4 is held low while Complementary output on pin 5 is held high.
Output is enabled by setting pin 2 at < Vcc -1.6V, See ordering information for enable/disable option.
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
4
J-Type Voltage Controlled Crystal Oscillator
PECL Output Option
Output Wave Form
Output Test Conditions
Output Test Conditions (25±5°C)
1
Ordering Information for the PECL output option (add frequency)
Package
Supply
Voltage
VCXO
Type
APR
(ppm)
Operating
Temp.
(°C)
Output/Duty
Cycle
Min/Max
Enable/
Disable
Specials
J
6 pin
Ceramic
SOJ
C
D
5V±10%
U
VCXO
F
±32
±50
C
L
0/70
M
PECL
45/55%
U
E
None
N
P
Standard
3.3V±10% L ±10%
G
-40/85
Enable/
Disable
on pin 2
6ps rms
(<1ps rms
12 kHz-20 MHz)
jitter
linear
VCXO
M ±20ppm
stability
R
T
12ps rms
jitter
VCXO
20ps rms
jitter
1. Note: Not all combinations are possible.
Example: JDUGLMEP @77.76 MHz = 3.3 volt, VCXO @77.760, ±50 ppm APR, -40/85°C, 45/55% Symmetry,
PECL, Enable/Disable on pin 2, 6ps rms jitter
Standard Frequencies, in MHz, for PECL output options
77.760
82.944
155.52
Other frequencies available upon request.
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
5
J-Type Voltage Controlled Crystal Oscillator
Outline Drawing
Tape and Reel
Tape and Reel Dimensions (mm)
Tape Dimensions
Reel Dimensions
# Per Reel
Product
A
B
C
D
E
F
G
H
I
J
K
L
J-Type
24
11.5
1.5
4
12
1.78
21
13
100
5
25
330 200
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
6
J-Type Voltage Controlled Crystal Oscillator
Typical Frequency Translation Diagram
Typical Clock Smoothing Diagram
Recommended Solder Reflow Profile
Suggested IR profile
a preheat period in which the flux is activated, a ramp
VI qualification includes aging at various extreme tem-
peratures, shock and vibration; temperature cycling
and IR reflow simulation. The conditions a device can
withstand are well understood and devices can be
subjected to the profile in figure above. This profile
shows a ramp up condition to prevent thermal shock,
up to 183° C which is the eutectic temperature of Sn/Pb
and a gradual cool down. The time above 183° C should
not exceed 60 seconds and the peak temperature
should be no more than 220° C for 10 seconds. The J-
types are 100% screened for hermeticity so an aqueous
wash is not an issue.
Vectron International • 166 Glover Avenue, Norwalk, CT 06856 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
7
J-Type Voltage Controlled Crystal Oscillator
Recommended Solder Pad Layout
Mechanical and Environmental Compliance
Parameter
Conditions
Mechanical Shock
Mechanical Vibration
Solderability
Gross and Fine Leak
Resistance to Solvents
MIL-STD-883, 2002
MIL-STD-883, 2007
MIL-STD-883, 2003
MIL-STD-883, 1014
MIL-STD-883, 1016
Handling Precautions
Although ESD protection circuitry has been designed
into the the J-type, proper precautions should be
taken when handling and mounting. VI employs a
human body model and a charged-device model
(CDM) for ESD susceptibility testing and design pro-
tection evaluation. ESD thresholds are dependent on
the circuit parameters used to define the model.
Although no industry wide standard has been adopted
for the CDM, a standard HBM of resistance =
1.5Kohms and capacitance = 100pF is widely used
and therefore can be used for comparison purposes.
ESD Ratings
Model
Human Body Model
Minimum
1500V
Charged Device Model
1500V
Visit Our Website at
www.vectron.com
For additional information please contact:
USA: Vectron International • 166 Glover Avenue, Norwalk, CT 06856 . . . . Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON
EUROPE: In Denmark, Finland, Ireland, Israel, Norway, Spain, UK . . . . . . . Tel: 44 (0) 1703 766 288 • Fax: 44 (0) 1703 766 822
In Austria, Belgium, France, Germany, Italy, Luxembourg
Netherlands, Sweden, Switzerland, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: 49 (0) 72 63 6480 • Fax: 49 (0) 72 63 6196
ASIA: In China, Taiwan, Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: 603-598-0070 • Fax: 603-598-0075
In Korea, Singapore, Australia, India . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: 203-853-4433 • Fax: 203-849-1423
www.vectron.com
Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Printed in USA 6/00
© Vectron International 2000
8
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明