NCP4586SN2.5T1RT [ETC]
Analog IC ; 模拟IC\n![NCP4586SN2.5T1RT](http://pdffile.icpdf.com/pdf1/p00006/img/icpdf/NCP45_29865_icpdf.jpg)
型号: | NCP4586SN2.5T1RT |
厂家: | ![]() |
描述: | Analog IC
|
文件: | 总12页 (文件大小:117K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
NCP4555, NCP4586
100 mA and 150 mA CMOS
LDOs with Shutdown and
Error Output
The NCP4555 and NCP4586 are high accuracy (typically "0.5%)
CMOS upgrades for older (bipolar) low dropout regulators. Designed
specifically for battery–operated systems, the devices’ CMOS
construction eliminates wasted ground current, significantly
extending battery life. Total supply current is typically 50 µA at full
load (20 to 60 times lower than in bipolar regulators).
The devices’ key features include ultra low noise operation, very
low dropout voltage – typically 180 mV (NCP4555) and 270 mV
(NCP4586) at full load – and fast response to step changes in load. An
error output (ERROR) is asserted when the devices are
out–of–regulation (due to a low input voltage or excessive output
current). ERROR can be used as a low battery warning or as a
processor RESET signal (with the addition of an external RC
http://onsemi.com
5
SOT–23
SN SUFFIX
CASE 1212
4
1
2
3
PIN CONNECTIONS
1
2
3
5
4
V
V
OUT
IN
network). Supply current is reduced to 0.5 µA (max) and both V
OUT
GND
SHDN
and ERROR are disabled when the shutdown input is low. The devices
incorporate both over–temperature and over–current protection.
The NCP4555 and NCP4586 are stable with an output capacitor of
only 1.0 µF and have a maximum output current of 100 mA and
150 mA, respectively. For higher output current regulators, please see
ERROR
(Top View)
the NCP4569 (I
= 300 mA) data sheet.
OUT
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
Features
• Zero Ground Current for Longer Battery Life
• Very Low Dropout Voltage
• Guaranteed 100 mA and 150 mA Output
(NCP4555 and NCP4586 Respectively)
• High Output Voltage Accuracy
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 11 of this data sheet.
• Standard or Custom Output Voltages
• Power–Saving Shutdown Mode
• ERROR Output Can Be Used as a Low Battery Detector, or
Processor Reset Generator
• Over–Current and Over–Temperature Protection
• Space–Saving 5–Pin SOT–23A Package
• Pin Compatible Upgrades for Bipolar Regulators
Applications
• Battery–Operated Systems
• Portable Computers
• Medical Instruments
• Instrumentation
• Cellular/GSMS/PHS Phones
• Linear Post–Regulators for SMPS
• Pagers
Semiconductor Components Industries, LLC, 2001
1
Publication Order Number:
February, 2001 – Rev. 0
NCP4555/D
NCP4555, NCP4586
5
1
2
3
V
IN
V
V
V
OUT
IN
OUT
+
1 µF
NCP4555
NCP4586
GND
1 M
4
SHDN
ERROR
ERROR
Shutdown Control (from Power Control Logic)
Figure 1. Typical Application
ABSOLUTE MAXIMUM RATINGS*
Rating
Symbol
Value
6.5
Unit
V
Input Voltage
–
–
–
Output Voltage
–0.3 to V + 0.3
V
IN
Power Dissipation
Internally Limited
–
Operating Temperature Range
Storage Temperature
T
–40 t T t 125
°C
°C
V
A
J
T
stg
–65 to +150
Maximum Voltage on any Pin
Lead Temperature (Soldering, 10 Sec.)
ESD Withstand Voltage
Latch–Up Performance (Note 2.)
–
–
V
IN
+ 0.3 to – 0.3
+260
°C
V
Human Body Model (Note 1.)
V
ESD
u2000
I
mA
LATCH–UP
Positive
250
Negative
u500
*Stresses above those listed under “Absolute Maximum Ratings’’ may cause permanent damage to the device. These are stress ratings only
and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications
is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability.
1. Tested to EIA/JESD22–A114–A
2. Tested to EIA/JESD78
http://onsemi.com
2
NCP4555, NCP4586
ELECTRICAL CHARACTERISTICS (V = V
+ 1.0 V, I = 100 µA, C = 3.3 µF, SHDN u V , T = 25°C, unless otherwise
IN
OUT
L
L
IH
A
noted. Boldface type specifications apply for junction temperatures of –40°C to +125°C.)
Characteristics
Test Conditions
Symbol
Min
Typ
Max
6.0
Unit
V
Input Operating Voltage
–
–
V
IN
–
–
Maximum Output Current
NCP4555
NCP4586
I
mA
OUTMAX
100
150
–
–
–
–
Output Voltage
Note 3.
Note 4.
V
V
R
– 2.5%
V
R
" 0.5%
V + 2.5%
R
V
OUT
V
OUT
Temperature Coefficient
TCV
–
–
20
40
–
–
ppm/°C
OUT
Line Regulation
(V + 1.0 V) v V v 6.0 V DV
/DV
IN
–
0.05
0.35
%
%
R
IN
OUT
Load Regulation
NCP4555
NCP4586
DV
/V
OUT OUT
I = 0.1 mA to I
–
–
0.5
0.5
2.0
3.0
L
OUTMAX
I = 0.1 mA to I
L
OUTMAX
Note 5.
Dropout Voltage
I = 100 µA
V
IN
– V
OUT
–
–
–
–
–
2.0
65
85
180
270
–
–
120
250
400
mV
L
I = 20 mA
L
I = 50 mA
L
NCP4555, NCP4586
NCP4586
I = 100 mA
L
I = 150 mA
L
Note 6.
Supply Current (Note 10.)
Shutdown Supply Current
Power Supply Rejection Ratio
Output Short Circuit Current
Thermal Regulation
SHDN = V , I = 0
I
IN
–
–
–
–
–
–
50
0.05
64
80
0.5
–
µA
µA
IH
L
SHDN = 0 V
I
INSD
F
RE
v 1.0 kHz
PSRR
dB
V
OUT
= 0 V
I
300
0.04
160
450
–
mA
V/W
°C
OUTSC
Notes 7., 8.
–
DV
/DP
OUT D
Thermal Shutdown Die
Temperature
T
SD
–
Thermal Shutdown Hysteresis
Output Noise
–
DT
–
–
10
–
–
°C
SD
I = I
L
eN
260
Ǹ
OUTMAX
470 pF from Bypass to GND
nVń Hz
SHDN Input
SHDN Input High Threshold
V
V
= 2.5 V to 6.5 V
= 2.5 V to 6.5 V
V
45
–
–
–
–
%V
%V
IN
IH
IN
SHDN Input Low Threshold
V
15
IN
IL
IN
ERROR Output
Minimum V Operating Voltage
–
V
1.0
–
–
–
–
400
–
V
IN
INMIN
Output Logic Low Voltage
ERROR Threshold Voltage
ERROR Positive Hysteresis
1.0 mA Flows to ERROR
See Figure 3
V
mV
OL
TH
V
–
0.95 x V
50
V
R
Note 9.
V
–
–
mV
HYS
3. V is the regulator output voltage setting. For example: V = 2.5 V, 2.7 V, 2.85 V, 3.0 V, 3.3 V, 3.6 V, 4.0 V, 5.0 V.
R
C
R
4. T
V =
(V
OUT
)
6
10
* V
OUTMAX
V
OUTMIN
DT
OUT
5. Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested over a load range
from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating effects are covered by the thermal
regulation specification.
6. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value.
7. Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load
or line regulation effects. Specifications are for a current pulse equal to I
at V = 6.0 V for T = 10 msec.
IN
LMAX
8. The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature, and the
thermal resistance from junction–to–air (i.e. T , T , q ). Exceeding the maximum allowable power dissipation causes the device to initiate
A
J
JA
thermal shutdown. Please see Thermal Considerations section of this data sheet for more details.
9. Hysteresis voltage is referenced by V .
R
10.Apply for Junction Temperatures of –40°C to +85°C.
http://onsemi.com
3
NCP4555, NCP4586
PIN DESCRIPTION
Pin
Number
Symbol
Description
1
2
3
V
Unregulated supply input.
Ground terminal.
IN
GND
SHDN
Shutdown control input. The regulator is fully enabled when a logic high is applied to this input. The
regulator enters shutdown when a logic low is applied to this input. During shutdown, output voltage
falls to zero, ERROR is open circuited and supply current is reduced to 0.5 µA (max).
4
5
ERROR
Out–of–Regulation Flag. (Open drain output). This output goes low when V
approximately –5.0%.
is out–of–tolerance by
OUT
V
OUT
Regulated voltage output.
DETAILED DESCRIPTION
Figure 2 shows a typical application circuit. The regulator
is enabled any time the shutdown input (SHDN) is at or
The NCP4555 and NCP4586 are precision fixed output
voltage regulators. Unlike bipolar regulators, the NCP4555
and NCP4586 supply current does not increase with load
above V , and shutdown (disabled) when SHDN is at or
IH
below V . SHDN may be controlled by a CMOS logic gate,
IL
or I/O port of a microcontroller. If the SHDN input is not
required, it should be connected directly to the input supply.
While in shutdown, supply current decreases to 0.05 µA
current. In addition, V
remains stable and within
OUT
regulation at very low load currents (an important
consideration in RTC and CMOS RAM battery back–up
applications).
(typical), V
falls to zero volts, and ERROR is
OUT
open–circuited.
V
IN
V
OUT
V
OUT
+
+
1 µF
C1
+
1 µF
NCP4555
NCP4586
GND
BATTERY
+
V
SHDN
ERROR
R1
1 M
C2 Required Only
Shutdown Control
(to CMOS Logic or Tie
to V if unused)
if ERROR is used as a
Processor RESET Signal
(See Text)
BATTLOW
or RESET
IN
+
C2
0.2 µF
Figure 2. Typical Application Circuit
ERROR Open Drain Output
ERROR is driven low whenever V
Note that ERROR is active when V
falls to V , and
OUT TH
falls out of
inactive when V
rises above V by V
.
OUT
OUT
TH
HYS
regulation by more than –5.0% (typical). This condition may
be caused by low input voltage, output current limiting, or
thermal limiting. The ERROR threshold is 5.0% below rated
As shown in Figure 2, ERROR can be used as a battery
low flag, or as a processor RESET signal (with the addition
of timing capacitor C2). R1 x C2 should be chosen to
V
OUT
regardless of the programmed output voltage value
maintain ERROR below V of the processor RESET input
IH
(e.g. ERROR = V at 4.75 V (typ.) for a 5.0 V regulator and
for at least 200 msec to allow time for the system to stabilize.
OL
2.85 V (typ.) for a 3.0 V regulator). ERROR output
operation is shown in Figure 3.
Pull–up resistor R1 can be tied to V
, V or any other
OUT IN
voltage less than (V + 0.3 V).
IN
http://onsemi.com
4
NCP4555, NCP4586
The maximum allowable power dissipation (Equation 2)
is a function of the maximum ambient temperature
(T ), the maximum allowable die temperature (125°C),
V
OUT
HYSTERESIS (V
)
HYS
V
TH
AMAX
and the thermal resistance from junction–to–air (q ). The
JA
5–Pin SOT–23 package has a q
of approximately
JA
2005C/Watt when mounted on a single layer FR4 dielectric
ERROR
copper clad PC board.
V
IH
(T
* T
)
AMAX
JMAX
P
+
DMAX
V
OL
q
JA
Where all terms are previously defined.
(eq. 2)
Figure 3. ERROR Output Operation
Equation 1 can be used in conjunction with Equation 2 to
ensure regulator thermal operation is within limits. For
example:
Output Capacitor
A 1.0 µF (min) capacitor from V
recommended. The output capacitor should have an
effective series resistance of 5.0 Ω or less, and a resonant
frequency above 1.0 MHz. A 1.0 µF capacitor should be
to ground is
OUT
GIVEN :
V
+ 3.0 V " 5.0%
+ 2.7 V * 2.5%
+ 40 mA
INMAX
V
OUTMIN
I
LOAD
55°C
+
T
AMAX
connected from V to GND if there is more than 10 inches
IN
of wire between the regulator and the AC filter capacitor, or
if a battery is used as the power source. Aluminum
electrolytic or tantalum capacitor types can be used. (Since
many aluminum electrolytic capacitors freeze at
approximately –30°C, solid tantalums are recommended for
applications operating below –25°C.) When operating from
sources other than batteries, supply–noise rejection and
transient response can be improved by increasing the value
of the input and output capacitors and employing passive
filtering techniques.
FIND : 1. Actual power dissipation.
2. Maximum allowable dissipation.
Actual power dissipation :
P
[ (V
* V
INMAX
)I
OUTMIN LOADMAX
D
* 3
[
]
+ (3.0 1.05) * (2.7 .975) 40 10
+ 20.7 mW
Maximum allowable power dissipation :
(T * T
)
AMAX
JMAX
Thermal Considerations
P
+
DMAX
q
JA
Thermal Shutdown
+ (125 * 55)
Integrated thermal protection circuitry shuts the regulator
off when die temperature exceeds 160°C. The regulator
remains off until the die temperature drops to approximately
150°C.
220
+ 318 mW
In this example, the NCP4555 dissipates a maximum of
only 20.7 mW; far below the allowable limit of 318 mW. In
a similar manner, Equation 1 and Equation 2 can be used to
calculate maximum current and/or input voltage limits.
Power Dissipation
The amount of power the regulator dissipates is primarily
a function of input and output voltage, and output current.
The following equation is used to calculate worst case actual
power dissipation:
Layout Considerations
The primary path of heat conduction out of the package is
via the package leads. Therefore, layouts having a ground
plane, wide traces at the pads, and wide power supply bus
P
[ (V
* V
INMAX
)I
OUTMIN LOADMAX
D
Where :
P
+ worst case actual power dissipation
D
lines combine to lower q and, therefore, increase the
V
+ maximum voltage on V
JA
INMAX
IN
V
+ minimum regulator output voltage
+ maximum output (load) current
maximum allowable power dissipation limit.
OUTMIN
I
LOADMAX
(eq. 1)
http://onsemi.com
5
NCP4555, NCP4586
TYPICAL CHARACTERISTICS
(Unless otherwise specified, all parts are measured at Temperature = 25°C)
0.020
0.018
0.016
0.014
0.012
0.010
0.008
0.006
0.004
0.002
0.000
0.100
I
= 10 mA
I
= 50 mA
0.090
0.080
0.070
0.060
0.050
0.040
0.030
0.020
0.010
0.000
LOAD
LOAD
C
C
= 1 µF
C
C
= 1 µF
= 1 µF
IN
OUT
IN
= 1 µF
OUT
–40
–20
0
20
50
70
125
–40
–20
0
20
50
70
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Dropout Voltage vs. Temperature
(VOUT = 3.3 V)
Figure 5. Dropout Voltage vs. Temperature
(VOUT = 3.3 V)
0.200
0.180
0.160
0.140
0.120
0.100
0.080
0.060
0.040
0.020
0.000
0.300
0.250
I
= 150 mA
LOAD
I
= 100 mA
LOAD
0.200
0.150
0.100
0.050
0.000
C
C
= 1 µF
= 1 µF
IN
C
C
= 1 µF
= 1 µF
IN
OUT
OUT
–40
–20
0
20
50
70
125
–40
–20
0
20
50
70
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 6. Dropout Voltage vs. Temperature
(VOUT = 3.3 V)
Figure 7. Dropout Voltage vs. Temperature
(VOUT = 3.3 V)
90
80
70
60
50
40
30
20
10
0
90
80
70
60
50
40
30
20
10
0
I
= 10 mA
I
= 100 mA
LOAD
LOAD
C
C
= 1 µF
= 1 µF
C
C
= 1 µF
IN
= 1 µF
OUT
IN
OUT
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5
(V)
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5
(V)
V
IN
V
IN
Figure 8. Ground Current vs. VIN (VOUT = 3.3 V)
Figure 9. Ground Current vs. VIN (VOUT = 3.3 V)
http://onsemi.com
6
NCP4555, NCP4586
TYPICAL CHARACTERISTICS
(Unless otherwise specified, all parts are measured at Temperature = 25°C)
80
70
60
50
40
30
20
10
0
3.5
I
= 150 mA
I
= 0 mA
LOAD
LOAD
3
2.5
2
1.5
1
C
C
= 1 µF
= 1 µF
IN
OUT
C
C
= 1 µF
= 1 µF
IN
OUT
0.5
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5
(V)
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
(V)
6
6.5 7
V
IN
V
IN
Figure 10. Ground Current vs. VIN (VOUT = 3.3 V)
Figure 11. VOUT vs. VIN (VOUT = 3.3 V)
3.5
3.0
3.320
3.315
3.310
3.305
3.300
3.295
3.290
3.285
3.280
3.275
I
= 10 mA
LOAD
I
= 100 mA
LOAD
2.5
2.0
1.5
1.0
0.5
C
C
V
= 1 µF
= 1 µF
= 4.3 V
IN
C
C
= 1 µF
= 1 µF
IN
OUT
OUT
IN
0.0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
(V)
6
6.5 7
–40
–20
–10
0
20
40
85
125
V
IN
TEMPERATURE (°C)
Figure 12. VOUT vs. VIN (VOUT = 3.3 V)
Figure 13. Output Voltage vs. Temperature
(VOUT = 3.3 V)
3.290
3.288
3.286
3.284
3.282
3.280
3.278
3.276
3.274
5.025
5.020
5.015
5.010
5.005
5.000
4.995
I
= 150 mA
I
= 10 mA
LOAD
LOAD
C
C
V
= 1 µF
= 1 µF
= 4.3 V
V
C
C
= 6 V
IN
IN
= 1 µF
OUT
= 1 µF
IN
4.990
4.985
OUT
IN
–40
–20 –10
0
20
40
85
125
–40
–20 –10
0
20
40
85
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 14. Output Voltage vs. Temperature
(VOUT = 3.3 V)
Figure 15. Output Voltage vs. Temperature
(VOUT = 5 V)
http://onsemi.com
7
NCP4555, NCP4586
TYPICAL CHARACTERISTICS
(Unless otherwise specified, all parts are measured at Temperature = 25°C)
70
4.994
4.992
I
= 150 mA
LOAD
I
= 10 mA
LOAD
60
50
40
30
20
10
4.990
4.988
4.986
4.984
4.982
4.980
4.978
4.976
4.974
V
C
C
= 6 V
IN
V
C
C
= 6 V
IN
= 1 µF
OUT
= 1 µF
OUT
= 1 µF
IN
= 1 µF
IN
0
–40
–20 –10
0
20
40
85
125
–40 –20 –10
0
20
40
85
125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 16. Output Voltage vs. Temperature
(VOUT = 5 V)
Figure 17. Temperature vs. Quiescent Current
(VOUT = 5 V)
80
70
60
50
40
30
20
10
0
10.0
1.0
0.1
0.0
I
= 150 mA
LOAD
R
C
C
= 50 Ω
= 1 µF
= 1 µF
LOAD
V
C
C
= 6 V
= 1 µF
= 1 µF
IN
OUT
OUT
IN
IN
–40
–20 –10
0
20
40
85
125
0.01 k
0.1 k
1 k
10 k
100 k 1000 k
TEMPERATURE (°C)
FREQUENCY (Hz)
Figure 18. Temperature vs. Quiescent Current
(VOUT = 5 V)
Figure 19. Output Noise vs. Frequency
1000
–30
–35
I
= 10 mA
C
= 1 µF to 10 µF
OUT
OUT
V
V
V
C
C
= 4 V
= 100 mV p–p
= 3 V
INDC
INAC
OUT
–40
–45
–50
–55
–60
–65
–70
–75
–80
100
10
= 0
IN
= 1 µF
OUT
Stable Region
1
0.1
0.01
0
10
20 30
40
50 60
70 80 90 100
0.01 k
0.1 k
1 k
10 k
100 k 1000 k
LOAD CURRENT (mA)
FREQUENCY (Hz)
Figure 20. Stability Region vs. Load Current
Figure 21. Power Supply Rejection Ratio
http://onsemi.com
8
NCP4555, NCP4586
Conditions:
Conditions:
C
V
= 1 µF, C
= 1 µF, I
= 100 mA,
C
V
= 1 µF, C
= 1 µF, I
= 100 mA
IN
IN
OUT
LOAD
IN
IN
OUT
LOAD
= 4.3 V, Temp = 25°C, Rise Time = 184 µS
= 6 V, Temp = 25°C, Rise Time = 192 µS
Figure 22. Measure Rise Time of 3.3 V LDO
Figure 23. Measure Rise Time of 5.0 V LDO
Conditions:
Conditions:
C
V
= 1 µF, C
= 1 µF, I
= 100 mA
C
V
= 1 µF, C
= 1 µF, I
= 100 mA
IN
IN
OUT
LOAD
IN
IN
OUT
LOAD
= 4.3 V, Temp = 25°C, Fall Time = 52 µS
= 6 V, Temp = 25°C, Fall Time = 88 µS
Figure 24. Measure Fall Time of 3.3 V LDO
Figure 25. Measure Fall Time of 5.0 V LDO
http://onsemi.com
9
NCP4555, NCP4586
I
was increased until temperature of die reached about
LOAD
160°C, at which time integrated thermal protection circuitry
shuts the regulator off when die temperature exceeds
approximately 160°C. The regulator remains off until die
temperature drops to approximately 150°C.
Conditions:
= 6 V, C = 0 µF, C = 1 µF
OUT
V
IN
IN
Figure 26. Thermal Shutdown Response of 5.0 V
LDO
Component Taping Orientation for 5–Pin SOT–23 Devices
USER DIRECTION OF FEED
DEVICE
MARKING
PIN 1
Standard Reel Component Orientation
TR Suffix Device
(Mark Right Side Up)
PIN 1
USER DIRECTION OF FEED
M A R K I N G
D E V I C E
W
P
Reverse Reel Component Orientation
RT Suffix Device
(Mark Upside Down)
Carrier Tape, Number of Components Per Reel and Reel Size
Package
Carrier Width (W)
Pitch (P)
Part Per Full Reel
Reel Size
SOT–23
8 mm
4 mm
3000
7 inches
http://onsemi.com
10
NCP4555, NCP4586
MARKING DIAGRAM
1
2
3
4
1
2
and
= Two Letter Part Number Codes
+ Temperature Range and Voltage
3
4
= Year and Quarter Code
= Lot ID Number
ORDERING INFORMATION
Marking
Voltage
Option*
Junction
Temperature Range
and
1
2
Device
Package
Shipping
NCP4555SNxxT1
1.8
2.8
2.85
3.0
DY
DZ
D8
D3
D5
3.3
NCP4586SNxxT1
2.5
2.7
2.8
2.85
3.0
3.3
3.6
4.0
5.0
P1
P2
PZ
P8
P3
P5
P9
P0
P7
SOT–23
–40°C to + 125°C
3000 Tape & Reel
xx Indicates Output Voltages
*Other output voltages are available. Please contact ON Semiconductor for details.
http://onsemi.com
11
NCP4555, NCP4586
PACKAGE DIMENSIONS
SOT–23
SN SUFFIX
CASE 1212–01
ISSUE O
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
A2
B
A
D
S
0.05
3. DATUM C IS A SEATING PLANE.
A1
L
MILLIMETERS
5
1
4
3
DIM MIN
MAX
0.10
1.30
0.50
0.25
3.00
3.10
1.80
E
A1
A2
B
0.00
1.00
0.30
0.10
2.80
2.50
1.50
2
E1
C
C
L1
B
5X
D
E
C
M
S
S
0.10
C B
A
E1
e
e
0.95 BSC
1.90 BSC
e1
L
e1
0.20
0.45
---
L1
0.75
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
CENTRAL/SOUTH AMERICA:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–spanish@hibbertco.com
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
Toll–Free from Mexico: Dial 01–800–288–2872 for Access –
then Dial 866–297–9322
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
001–800–4422–3781
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–german@hibbertco.com
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–french@hibbertco.com
Email: ONlit–asia@hibbertco.com
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: r14525@onsemi.com
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: ONlit@hibbertco.com
ON Semiconductor Website: http://onsemi.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
For additional information, please contact your local
Sales Representative.
*Available from Germany, France, Italy, UK, Ireland
NCP4555/D
相关型号:
©2020 ICPDF网 联系我们和版权申明