PBA04101 [ETC]

MODEL LDD - LARGE DIGIT DISPLAY;


型号：	PBA04101
厂家：	ETC
描述：	MODEL LDD - LARGE DIGIT DISPLAY
文件：	总4页 (文件大小：553K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Bulletin No. LDD-N

Drawing No. LP0205

Released 1/06

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

MODEL LDD - LARGE DIGIT DISPLAY

WIDE SELECTION OF INPUT MODULES

3.32 INCH (84.4 mm) HIGH DIGITS

115/230 VAC SWITCH SELECTABLE

RUGGED STEEL CONSTRUCTION

AVAILABLE IN 4 OR 6-DIGIT VERSIONS

AVAILABLE WITH RED OR GREEN LED DISPLAY

SEALED FRONT PANEL CONSTRUCTION (NEMA 4/IP65)

VERSATILE MOUNTING OPTIONS

TEMPLATE PROVIDED FOR EASY INSTALLATION

DESCRIPTION

The Large Digit Display, Model LDD, is a versatile display which can

increase your productivity by offering your plant floor or production area a

visual display of their current status, such as counting, rate indication, real time,

or any engineering unit required. The LDD is available in either a 4-digit or a

6-digit display version with Red or Green LED displays, that accepts a selection

of personality boards to meet your specific application needs (see Personality

Module Bulletins for more information).

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the

manual or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

There are four panel wiring knock-outs provided, two 7/8" (22.2 mm) knock-

outs and two 1/2"(12.7 mm) knock-outs. Also provided is a removeable cover

located on the rear panel which will expose one open ended cut-out for easy

wire installation.

SPECIFICATIONS

1. DISPLAY: 3.32" (84.4 mm) High, Red or Green LED display.

2. POWER REQUIREMENTS: Switch selectable 115/230 VAC (±10%),

50/60 Hz, 17 VA 4-digit, 21 VA 6-digit (including module).

3. CONSTRUCTION: Steel construction textured with polyurethane paint for

scratch and corrosion resistance protection. Front panel meets NEMA 4/IP65

requirements for indoor use when properly installed. Installation Category II,

Pollution Degree 2. (Panel gasket included with unit.)

4. ENVIRONMENTAL CONDITIONS:

The LDD has a sealed front panel which meets NEMA 4/IP65 requirements

for wash-down and dusty environments when properly installed. The 3.32"

(84.4 mm) digits are readable to 130 feet (40 M).

Operating Temperature: SEE MODULE LITERATURE

Storage Temperature: -40 to 70°C

CAUTION: Risk of electric shock.

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

Operating and Storage Humidity: 85% max. relative (non-condensing)

over operating range

Altitude: Up to 2000 meters

DIMENSIONS In inches [mm]

PANEL CUT-OUT

SPECIFICATIONS (Cont’d)

FIGURE 1 (shown with cover removed)

5. CERTIFICATIONS AND COMPLIANCES:

SAFETY

IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment

for measurement, control, and laboratory use, Part 1.

IP65 Enclosure rating (Face only), IEC 529

Type 4 Enclosure rating (Face only), UL50

EMC EMISSIONS: Meets EN 50081-2: Industrial Environment.

EMC IMMUNITY: Meets EN 50082-2: Industrial Environment.

Refer to individual personality module specifications for aditional

information.

6. MOUNTING REQUIREMENTS:

Max. panel thickness is 0.375" (9.5 mm).

Min. panel thickness for NEMA 4/IP65 sealing is 0.125" (3.2 mm).

7. WEIGHT: 8 lbs (3.6 kg) (less module).

Warning: Disconnect all power before installing or removing module.

FIGURE 2

SET-UP

To place the personality module into the LDD, first remove the rear cover

by unscrewing the two captive fasteners. Then, before installing the module

into the LDD, configure the module for the specific application by SETTING

ALL APPLICABLE DIP SWITCHES AND JUMPERS AT THIS TIME (see

accompanying module data sheet). Place the module on the plastic standoffs

(see figure 1). Push on the four posts as shown in figure 2 until the carrier snaps

into place.

Note: Power should NOT be applied until the terminal block is plugged into the

module AND the module is properly installed into the Large Digit Display.

Select the proper voltage by setting the switch to either 115 or 230 volts.

Connect the display and power cables on the module to the appropriate

connectors on the power supply board (see figure 2).

To program the Intelligent Meter, three normally open momentary

pushbuttons are connected to “P”, “UP”, “DOWN”, and common of the LDD

(not included with the Intelligent Meter). The Model PGM is a small plastic

case with three normally open momentary pushbuttons and 10 feet (3 M) of

shielded cable, and is well suited for programming the Intelligent Meter

module. Although, any normally open, momentary pushbutton switches can be

used. (SEE APPROPRIATE MODULE LITERATURE FOR SET-UP AND

OTHER CONNECTIONS.)

To remove module from the LDD, disconnect the display and power cables,

then remove the carrier from the standoffs by disengaging the tabs and

simultaneously lifting the carrier. Repeat this until the module has cleared all 4

standoffs.

INSTALLATION ENVIRONMENT

The unit should be installed in a location that does not exceed the maximum

operating temperature and provides good air circulation. Placing the unit near

devices that generate excessive heat should be avoided.

The LDD may be cleaned using alcohol compounds such as Isopropanol or

methanol. Also, liquid glass cleaners may be used if they do NOT contain

ammonia.

FIGURE 3

NOTE: MINIMAL EXPOSURE OF KETONE SOLVENTS TO THE LDD IS

GOING TO CAUSE A WHITENING OF THE DISPLAY OVERLAY.

Continuous exposure to direct sunlight may accelerate the aging process of

the bezel.

The LDD is intended to be mounted into an enclosed panel with a gasket to

provide a water-tight seal. A gasket and ten 10 to 32 kep nuts are provided for

easy installation. The recommended minimum panel thickness for NEMA

4/IP65 applications is 0.125" (3.2 mm). Thinner panels may be used but may

distort and not provide a water-tight seal.

For ease of installation, the cardboard template (supplied with the LDD) may

be used to mark the holes and cut-out locations on the panel. After the panel

cut-out has been completed and deburred, insert the unit with the panel gasket,

into the panel as depicted in the drawing (see figure 3). Install the ten kep nuts

and tighten evenly for uniform gasket compression.

By using additional hardware, the LDD can be surface-wall mounted,

suspended, or bottom mounted. To surface-wall mount the unit, two sets of

MB6 brackets are required. To suspend or bottom mount the unit, one set of

MB6 brackets is required.

ORDERING INFORMATION

PERSONALITY MODULES

FOR APOLLO PERSONALITY MODULES

The following Apollo and IM capabilities are available as modules for the

Large Digit Display (LDD). These modules are ordered separately from the

LDD (see ordering information), and can quickly be installed by the user (see

“Set-up” for further details).

MODEL NO.

DESCRIPTION

Apollo Real Time Clock Module for use with

PART NUMBER

PBLCK

PBLCK000

the 6-digit Large Digit Display ⁽¹⁾

Apollo 4-digit Process Time Module for use

with the 4-digit Large Digit Display

Apollo 5-digit Process Time Module for use

with the 6-digit Large Digit Display ⁽²⁾

Apollo Time Base Rate Module for use

with the 4 or 6-digit Large Digit Display ⁽³⁾

Apollo Time Interval Rate Module for use

with the 4 or 6-digit Large Digit Display ⁽⁴⁾

Apollo 6-digit Totalizer Module for use

with the 4 or 6-digit Large Digit Display ⁽⁵⁾

Model

Digit Display

Required

4/6-digit

4-digit

PBLPT400

PBLPT500

PBLR0600

PBLRI600

PBLT0600

Application

Counting (Totalization)

Number

PBLPT

PBLT0600

PBLR0600

PBLRI600

PBLPT400

PBLPT500

PBLCK000

PBD1xxxx

PBD2xxxx

PBIxxxxx

PBAxxxxx

PBLSP600

Tachometer/Rate (Time Base)

Tachometer/Rate (Time Interval)

Process Time (Decimal Point)

Process Time (Chronometer)

Real Time Clock/Elapsed Time

Intelligent Decade Voltmeter (IMD1)

Intelligent Decade Current Meter (IMD2)

Intelligent Rate Meter (IMI)

PBLR

PBLRI

PBLT

6-digit

(1) See APLCK Bulletin for operating specifications.

(2) See APLPT Bulletin for operating specifications.

(3) See APLR Bulletin for operating specifications.

(4) See APLRI Bulletin for operating specifications.

(5) See APLT Bulletin for operating specifications.

6-digit

Intelligent Slave Display (IMA)

Apollo Slave Display (APLSP)

6-digit

4/6-digit

ORDERING INFORMATION FOR LARGE DIGIT DISPLAY

MODEL NO.

DESCRIPTION

PART NUMBER

LDD00400

LDD0G400

LDD00600

LDD0G600

MB600000

ENC70000

SHR10000

ORDERING INFORMATION

4-digit, Red Large Digit Display

4-digit, Green Large Digit Display

6-digit, Red Large Digit Display

6-digit, Green Large Digit Display

Mounting Brackets

FOR APOLLO BCD SLAVE MODULE

LDD

MODEL NO.

DESCRIPTION

PART NUMBER

Apollo BCD Slave Display Module for use

with 4 or 6-digit Large Digit Display

(See APLSP Bulletin for operating

specifications.)

MB6

ENC7

SHR

PBLSP

PBLSP600

LDD NEMA 4/IP65 Enclosure

Shroud For LDD

ORDERING INFORMATION FOR APOLLO INTELLIGENT METER MODULES

1. TOTALIZER

2. LINEARIZER

4-20 mA

ANALOG

OUTPUT

+18 VDC

EXCITATION

3. PEAK/VALLEY

4. TARE

DUAL

ALARM

SERIAL

OUTPUT

MODEL NO.

DESCRIPTION

PART NUMBER

5. E2-CON

6. EFFICIENCY

Intelligent Meter Modules

YES

PBD10000

PBD10100

PBD10102

PBD13100

PBD13107

PBD20000

PBD20100

PBD20102

PBD23100

PBD23107

PBA04101

PBA04104

PBA04107

PBI04100

PBI04101

PBI04102

PBI04103

PBI04107

PGM00000

For Decade Voltage Inputs*

PBD1

YES

(See IMD1 Bulletin for operating

Specifications.)

Intelligent Meter Modules

For Decade Current Input*

YES

1, 2, 3, 4, 5

YES

1, 2, 3, 4, 5

3, 5

1, 2, 3, 5, 6

PBD2

PBA

YES

(See IMD2 Bulletin for operating

Specifications.)

Intelligent Serial Slave Display Module*

(See IMA Bulletin for operating

Specifications.)

YES

20 mA SRC

+12 VDC

YES

Intelligent Digital Rate Meter*

(See IMI Bulletin for operating

Specifications.)

YES

PBI

YES

PGM

Programming Box

* Note: All the above Intelligent Meter modules require a 6-digit Large Digit Display, Model LDD00600 or LDD0G600.

TROUBLESHOOTING

For further technical assistance, contact technical support at the appropriate

company numbers listed.

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship

for a period limited to two years from the date of shipment, provided the products have been stored,

handled, installed, and used under proper conditions. The Company’s liability under this limited

warranty shall extend only to the repair or replacement of a defective product, at The Company’s

option. The Company disclaims all liability for any affirmation, promise or representation with

respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against

damages, claims, and expenses arising out of subsequent sales of RLC products or products

containing components manufactured by RLC and based upon personal injuries, deaths, property

damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be

to any extent liable, including without limitation penalties imposed by the Consumer Product Safety

Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty

Act (P.L. 93-637), as now in effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except those

expressly contained herein. The Customer acknowledges the disclaimers and limitations contained

herein and relies on no other warranties or affirmations.

Red Lion Controls AP

31, Kaki Bukit Road 3,

#06-04/05 TechLink

Singapore 417818

Tel +65 6744-6613

Fax +65 6743-3360

Red Lion Controls

20 Willow Springs Circle

York PA 17402

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls BV

Basicweg 11b

NL - 3821 BR Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

PBA04101 [ETC]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E