RP15-2405DAW/N-HC [ETC]
CONV DC/DC 15W 9-36VIN +/-05V;
| 型号： | RP15-2405DAW/N-HC |
| 厂家： | 
ETC |
| 描述： | CONV DC/DC 15W 9-36VIN +/-05V |
| 文件： | 总8页 (文件大小：466K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
• 4:1 wide input voltage range
• 1.6kVDC isolation
Features
DC/DC Converter
• UL certified
• Efficiency up to 88%
• Six-sided continuous shield
• No minimum load required
Regulated
Converter
RP15-AW
Description
15 Watt
1“ x 1“
Single and Dual
Output
The RP15-AW series are ultraminiature wide input voltage range power DC/DC converters in a case
half the size of industry standard 15W converters. Despite their small size, the RP15-AW converters
are fully specified devices with output currents up to 4 Amps, no minimum load, 1600VDC isolation
and low ripple/noise figures. The outputs are also fully protected against short circuits, overcurrent and
overvoltage. The RP15-AW series will find many uses in applications where board space and/or board
height is at a premium.
Selection Guide
Part Number
Input
Output
Output
Current
[mA]
Input (1) Efficiency (1) Max. Capacitive
Voltage Range Voltage
Current
[mA]
typ.
[%]
Load (2)
[µF]
[VDC]
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
9-36
9-36
9-36
18-75
18-75
18-75
[VDC]
3.3
5
12
15
3.3
5
12
15
5
12
15
5
RP15-243.3SAW (3,4)
RP15-2405SAW (3,4)
RP15-2412SAW (3,4)
RP15-2415SAW (3,4)
RP15-483.3SAW (3,4)
RP15-4805SAW (3,4)
RP15-4812SAW (3,4)
RP15-4815SAW (3,4)
RP15-2405DAW (3,4)
RP15-2412DAW (3,4)
RP15-2415DAW (3,4)
RP15-4805DAW (3,4)
RP15-4812DAW (3,4)
RP15-4815DAW (3,4)
4000
3000
1300
1000
4000
3000
1300
1000
1500
625
640
727
747
718
320
359
374
359
735
718
710
368
363
359
86
86
87
87
86
87
87
87
85
87
88
85
86
87
12000
6000
1000
660
12000
6000
1000
660
3000
520
330
3000
520
330
E196683
500
1500
625
UL60950-1 certified
12
15
500
Notes:
Note1: Maximum values at nominal input voltage and full load
Note2: Max. Cap load is tested at minimum Input and constant resistive load
Model Numbering
RP15-__ __ _AW/_-_
(4)
nom. Input Voltage
“Package
”
(3)
Output Voltage
“CTRL Logic
”
Single or Dual
Notes:
Note3: no suffix for standard part without Trim or CTRL pin
add suffix ”P” for CTRL function with positive logic (1=ON, 0=OFF) and Trim pin
add suffix “N” for CTRL function with negative logic (0=ON, 1=OFF) and Trim pin
Note4: add suffix “-HC” for premounted Heat-sink with clamps
Ordering Examples
RP15-2405SAW/P = 24V input, 5V output, single, positive Logic CTRL pin
RP15-4805DAW-HC = 48V input, 5V output, dual, without CTRL pin, Heat-sink premounted
www.recom-power.com
REV.: 5/2019
PD-1
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
BASIC CHARACTERISTICS
Parameter
Condition
Min.
Typ.
Max.
Input Filter
Pi-Type
nom. Vin = 24VDC
nom. Vin = 48VDC
9VDC
18VDC
24VDC
48VDC
36VDC
75VDC
Input Voltage Range
Input Surge Voltage
nom. Vin = 24VDC
nom. Vin = 48VDC
50VDC
100VDC
100s max.
DC-DC ON
DC-DC OFF
9VDC
nom. Vin = 24VDC
nom. Vin = 48VDC
8VDC
Under Voltage Lockout (UVLO)
DC-DC ON
DC-DC OFF
18VDC
16VDC
Input Reflected Ripple Current (5)
Output Voltage Trimming
Minimum Load
30mAp-p
refer to ”OUTPUT VOLTAGE TRIMMING”
-10%
0%
+10%
Power up
ON/OFF CTRL
30ms
30ms
Start-up Time
DC-DC ON
DC-DC OFF
Open or 3.0VDC < VCTRL< 15VDC
Short or 0VDC < VCTRL< 1.2VDC
Positive Logic
Negative Logic
ON/OFF CTRL (6)
DC-DC ON
DC-DC OFF
Short or 0VDC < VCTRL< 1.2VDC
Open or 3.0VDC < VCTRL< 15VDC
+1.0mA
DC-DC ON
DC-DC OFF
-0.5mA
360kHz
Input Current of CTRL pin
Standby Current
2.5mA
Internal Operating Frequency
400kHz
440kHz
3.3Vout, 5Vout
12Vout, 15Vout
75mVp-p
100mVp-p
measured at 20MHz BW,
with a 1µF M/C X7R and 10µF T/C
Ripple and Noise
5Vout, 12Vout, 15Vout
100mVp-p
Notes:
Note5: Simulated source impedance of 12µH. 12µH inductor in series with +Vin
Note6: If no suffix is specified, the control pin will be omitted. If fitted, the ON/OFF control function can be
positive or negative logic. The pin voltage is referenced to -Vin pin
RP15-2405SAW
Efficiency vs. Input Voltage full load
Efficiency vs. Output Current
95
90
85
80
75
70
65
60
55
50
45
95
90
85
80
75
70
65
60
9Vin
24Vin
36Vin
40
10
20
30
40
50
60
70
80
90
100
9
12
15
18
21
24
27
30
33
36
Output Current [%]
Input Voltage [VDC]
continued on next page
REV.: 5/2019
www.recom-power.com
PD-2
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
RP15-4805SAW
Efficiency vs. Input Voltage full load
Efficiency vs. Output Current
95
95
90
85
80
75
70
65
90
85
80
75
70
65
60
55
18Vin
48Vin
75Vin
50
45
40
10
20
30
40
50
60
70
80
90
100
18
24
30
36
42
48
54
60
66
75
Output Current [%]
Input Voltage [VDC]
OUTPUT VOLTAGE TRIMMING
Output Voltage Trimming
Single output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external
trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for choosing these
trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resistor
required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below.
Trim up
Trim down
-Vout
Trim
Trim
R
R
D
U
+Vout
RP15-xx3.3SAW
[%]
[VDC]
[kW]
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
3.333
385.071
3.366
191.511
3.399
126.990
3.432
94.730
3.465
3.498
3.531
3.564
46.340
3.597
40.963
3.63
75.374
62.470
53.253
36.662
[%]
[VDC]
[kW]
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
3.267
116.719
3.234
54.779
3.201
34.133
3.168
23.810
3.135
17.616
3.102
13.486
3.069
10.537
3.036
8.325
3.003
6.604
2.97
5.228
RP15-xx05SAW
[%]
[VDC]
[kW]
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
5.05
5.10
5.15
5.20
5.25
5.30
5.35
5.4
5.45
5.50
253.450
125.700
83.117
61.825
49.050
40.533
34.450
29.888
26.339
23.500
[%]
[VDC]
[kW]
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
4.95
4.90
4.85
4.80
4.75
4.70
4.65
4.60
4.55
4.50
248.340
120.590
78.007
56.715
43.940
35.423
29.340
24.778
21.229
18.390
continued on next page
REV.: 5/2019
www.recom-power.com
PD-3
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
RP15-xx12SAW
[%]
[VDC]
[kW]
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
12.12
203.223
12.24
99.057
12.36
64.334
12.48
46.973
12.60
36.557
12.72
29.612
12.84
24.652
12.96
20.932
13.08
18.038
13.20
15.723
[%]
[VDC]
[kW]
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
11.88
776.557
11.76
380.723
11.64
248.779
11.52
182.807
11.40
143.223
11.28
116.834
11.16
97.985
11.04
83.848
10.92
72.853
10.8
64.057
RP15-xx15SAW
[%]
[VDC]
[kW]
Trim up
Vout =
RU =
1
2
3
4
5
6
7
8
9
10
15.15
15.3
15.45
50.446
15.60
36.557
15.75
28.223
15.90
22.668
16.05
18.700
16.20
15.723
16.35
13.409
16.50
11.557
161.557
78.223
[%]
[VDC]
[kW]
Trim down
Vout =
RD =
1
2
3
4
5
6
7
8
9
10
14.85
818.223
14.70
401.557
14.55
262.668
14.40
193.223
14.25
151.557
14.10
123.779
13.95
103.938
13.80
89.057
13.65
77.483
13.50
68.223
REGULATIONS
Parameter
Condition
Value
Output Accuracy
1.0%
low line to high line,
full load
Single
Dual
0.2%
0.5%
Line Regulation
Single
Dual
0.2%
1.0%
Load Regulation
Cross Regulation
0% to 100% load
asymmetrical 25%<>100% load
25% load step change
5.0%
Transient Response Recovery Time
250µs typ.
PROTECTIONS
Parameter
Condition
Value
Short Circuit Protection (SCP)
continuous, automatic recovery
3.3Vout
5Vout
12Vout
15Vout
3.7 - 5.4VDC
5.6 - 7.0VDC
13.5 - 19.6VDC
16.8 - 20.5VDC
Over Voltage Protection (OVP)
zener diode clamp
Over Load Protection (OLP)
Isolation Voltage(7)
% of Iout rated
150% typ., Hiccup mode
I/P to O/P
I/P to O/P to case
1.6kVDC/ 1 minute
1.0kVDC/ 1 minute
1GW min.
Isolation Resistance
Isolation Capacitance
Viso= 500VDC
1000pF max.
Notes:
Note7: For repeat Hi-Pot testing, reduce the time and/or the test voltage
Note8: This power module is not internally fused. An input line fuse must always be used
Recom suggests: 24Vin= T3.15A; 48Vin= T1.6A slow blow types
www.recom-power.com
REV.: 5/2019
PD-4
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
ENVIRONMENTAL
Parameter
Condition
Value
-40°C to +67°C
-40°C to +105°C
without derating
with derating
Operating Temperature Range
Maximum Case Temperature
Temperature Coefficient
+105°C
0.02%/ꢀ max.
@ natural convection
0.1m/s
without heat-sink
with heat-sink
18.2ꢀ/W
15.8ꢀ/W
Thermal Impedance
Operating Humidity
Thermal Shock
Vibration
non-condensing
5% - 95% RH
according to MIL-STD-810F
according to MIL-STD-810F
according to MIL-HDBꢀ-217F, G.B.
Bellcore TR-NWT-000332 (9)
1459 x 103 hours
1330 x 103 hours
MTBF
+25°C
Derating Graph (10)
RP15-4805SAW-HC
RP15-4805SAW
100
80
60
40
20
0
100
80
60
40
20
0
-40 -20
0
20 40
60
80 100 120
105
-40 -20
0
20 40
60
80 100
73 105
120
Ambient Temperatu6r7e [°C]
Ambient Temperature [°C]
Notes:
Note9: BELLCORE TR-NWT-000332. Case l: 50% Stress, Ta= 40°C. MIL-HDBꢀ 217F Notice 2. Ta = 25°C, full load, (controlled environment)
Note10: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number
not shown here please contact RECOM Techsupport for detailed information
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
Condition
Standard
UL60950-1, 1st Edition
CAN/CSA-C22.2 No. 60950-1-07, 1st Edition
Information Technology Equipment, General Requirements for Safety
RoHS 2
E196683
RoHS-2011/65/EU + AM-2015/863
EMC Compliance
Condition
Standard / Criterion
Electromagnetic compatibility of multimedia equipment - Emission
requirements
with external filter
(see filter suggestion below)
EN55032, Class A and B
ESD Electrostatic discharge immunity test
Radiated, radio-frequency, electromagnetic field immunity test
Fast Transient and Burst Immunity (11)
Surge Immunity (11)
Air 8kV and Contact 6kV
EN61000-4-2, Criteria A
EN61000-4-3, Criteria A
EN61000-4-4, Criteria A
EN61000-4-5, Criteria A
EN61000-4-6, Criteria A
EN61000-4-8, Criteria A
10V/m
2kV
1kV
3Vr.m.s
Immunity to conducted disturbances, induced by radio-frequency fields
Power Magnetic Field Immunity
100A/m continuous; 1000A/m 1s
Notes:
Note11: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5
Recom suggests Nippon chemi-con ꢀY series 220µF/100V
continued on next page
www.recom-power.com
REV.: 5/2019
PD-5
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
EMC Filtering Suggestions according to EN55032
Single
Dual
C3
C3
F1
F1
+Vin
-Vin
+Vout
+Vin
-Vin
+Vout
+Vin
-Vin
+Vout
+Vin
+Vout
C1 C2
C1 C2
Com
-Vout
Com
-Vout
-Vout
-Vin
-Vout
C4
C4
Component List Class A
MODEL
C1
C2
C3/C4
RP15-24xxSAW,
RP15-24xxDAW
6.8µF/50V
1812 MLCC
6.8µF/50V
1812 MLCC
470pF/2kV
1808 MLCC
RP15-48xxSAW,
RP15-48xxDAW
2.2µF/100V
1812 MLCC
2.2µF/100V
1812 MLCC
470pF/2kV
1808 MLCC
Single
C4
Dual
C4
L1
L1
F1
F1
+Vin
-Vin
+Vout
+Vin
-Vin
+Vout
Com
-Vout
+Vin
-Vin
+Vout
+Vin
-Vin
+Vout
C1 C2
C3
C1 C2
C3
Com
-Vout
-Vout
-Vout
C5
C5
Component List Class B
MODEL
C1
C2
C3
C4/C5
L1
RP15-24xxSAW,
RP15-24xxDAW
6.8µF/50V
1812 MLCC
6.8µF/50V
1812 MLCC
CMC: 325µH
ref: WE 744290321 ref: CMC-06
N/A
RP15-48xxSAW,
RP15-48xxDAW
2.2µF/100V
1812 MLCC
2.2µF/100V
1812 MLCC
2.2µF/100V
1812 MLCC
CMC: 325µH
ref: WE 744290321 ref: CMC-06
DIMENSIONS and PHYSICAL CHARACTERISTICS
Parameter
Type
Value
case
base
nickel coated copper
FR4 PCB
Material
potting
epoxy (UL94V-0)
without Heat-sink
with Heat-sink
25.4 x 25.4 x 9.9mm
31.4 x 25.4 x 16.5mm
Dimensions (LxWxH)
Weight
without Heat-sink
with Heat-sink
15g
21.5g
continued on next page
REV.: 5/2019
www.recom-power.com
PD-6
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
Dimension Drawing (mm)
Pinning Information
25.4
25.4
Pin # Single
Dual
+Vin
1
2
3
4
5
6
+Vin
-Vin
-Vin
CTRL(3)
+Vout
Trim
CTRL(3)
+Vout
Com
2.54
0.1
8 x 2.54= 20.32
Ø 1.0
-Vout
-Vout
Recommended Footprint Details
2.54
Pin Pitch Tolerance 0.25mm
Tolerance:
xx.x= ±±.ꢀ55
xx.xx= ±±.ꢁꢀ55
3
6
5
4
4
5
6
2
1
1 Bottom View
Top View
2
3
Dimension Drawing with Heat-sink (mm)
25.4
Top View
Heat-sink
31.4
24.2
0.1
2.54
Ø 1.0
8 x 2.54= 20.32
2.54
3
6
5
4
4
2
1
1 Bottom View
5
Top View
2
3
6
www.recom-power.com
REV.: 5/2019
PD-7
RP15-AW
DC/DC Converter
Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated)
Series
PACKAGING INFORMATION
Parameter
Type
Value
tube
tray
without heat-sink
with heat-sink
257.0 x 28.5 x 21.0mm
230.0 x 180.0 x 28.0mm
Packaging Dimension (LxWxH)
tube
tray
without heat-sink
with heat-sink
8pcs
20pcs
Packaging Quantity
Storage Temperature Range
Storage Humidity
-55°C to +125°C
5% - 95% RH
non-condensing
The product information and specifications may be subꢀect to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The
products are not authorized for use in safety-critical applications without RECOMꢁs explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause
loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized
use of RECOM products in such safety-critical applications.
www.recom-power.com
REV.: 5/2019
PD-8
相关型号：
©2020 ICPDF网 联系我们和版权申明