VRS51L560-25-Q [ETC]
Versa 8051 MCUs with 8/16KB Flash; 的Versa 8051微控制器,8 / 16KB闪存型号: | VRS51L560-25-Q |
厂家: | ETC |
描述: | Versa 8051 MCUs with 8/16KB Flash |
文件: | 总40页 (文件大小:1724K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
VRS51x550/560
Datasheet
Rev 1.3
Versa 8051 MCUs with 8/16KB Flash
Overview
Feature Set
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
80C51/80C52 pin compatible
The VRS51x550 and VRS51x560 are low-cost 8-bit
microcontrollers based on the standard 80C51
microcontroller architecture. They are pin compatible
drop-in replacements for the 8051
12 clock periods per machine cycle
8KB / 16KB on-chip Flash memory
256 Bytes on-chip data RAM
32 I/O lines on four 8-bit ports
Full duplex serial port (UART)
3, 16-bit Timers/Counters
Watchdog Timer
8-bit Unsigned Division / Multiply
BCD arithmetic
Direct and Indirect Addressing
Two levels of interrupt priority and nested interrupts
Power saving modes
Code protection function
Operates at a clock frequency of up to 40MHz
Low EMI (inhibit ALE)
Programming voltage: 12V
Ideal for a wide range of applications requiring low to
midrange amounts of program/data memory, coupled
with streamlined peripheral support, the VRS51x550/560
devices feature 8KB/16KB, of Flash memory
(respectively), 256 bytes of RAM, a UART, three 16-bit
timers, a watchdog timer and power saving modes.
The VRS51x550 is available in 3.3 (VRS51L550) or 5
volt versions (VRS51C550), while the VRS51x560 is
available in a 5 volt version (VRS51C560). All devices
come in PLCC-44, QFP-44 and DIP-40 packages and
operate in the industrial temperature range. Flash can
be programmed using a parallel programmer available
from Ramtron or with a third party commercial
programmer.
Industrial Temperature range (-40°C to +85°C)
5V and 3V versions available (see ordering information)
FIGURE 2: VRS51X550 / VRS51X560 PLCC AND QFP PINOUT DIAGRAMS
FIGURE 1: VRS51X550 / VRS51X560 FUNCTIONAL DIAGRAM
6
40
7
1
39
P1.5
P1.6
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
#EA
P1.7
8051
PROCESSOR
ADDRESS/
DATA BUS
RESET
RXD/P3.0
NC
VRS51x550/560
PLCC-44
NC
ALE
TXD/P3.1
#INT0/P3.2
#INT1/P3.3
T0/P3.4
T1/P3.5
#PSEN
P2.7/A15
P2.6/A14
P2.5/A13
8KB / 16KB
FLASH
PORT 0
8
8
8
8
17
18
29
28
256
Bytes of RAM
PORT 1
PORT 2
PORT 3
UART
2 INTERRUPT
INPUTS
33
23
22
34
P0.3/AD3
P0.2/AD2
P0.1/AD1
P2.4/A12
P2.3/A11
P2.2/A10
TIMER 0
TIMER 1
TIMER 2
POWER
CONTROL
P0.0/AD0
VDD
P2.1/A9
P2.0/A8
VRS51x550/560
QFP-44
NC
T2/P1.0
T2EX/P1.1
P1.2
NC
VSS
WATCHDOG
TIMER
XTAL1
XTAL2
#RD/P3.7
#WR/P3.6
RESET
P1.3
44
P1.4
12
11
1
Ramtron International Corporation
1850 Ramtron Drive Colorado Springs
Colorado, USA, 80921
http://www.ramtron.com
MCU customer service: 1-800-943-4625, 1-514-871-2447, ext. 208
1-800-545-FRAM, 1-719-481-7000
?
?
?
page 1 of 40
VRS51x550/560
Pin Descriptions for QFP-44
TABLE 1: PIN DESCRIPTIONS FOR QFP-44/
QFP
- 44
QFP
- 44
Name
P2.6
A14
P2.7
A15
#PSEN
ALE
NC
#EA
P0.7
AD7
P0.6
AD6
P0.5
AD5
P0.4
AD4
P0.3
AD3
P0.2
AD2
P0. 1
AD1
P0.0
AD0
VDD
NC
I/O
I/O
O
I/O
O
O
O
-
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
Function
Name
I/O
Function
Bit 6 of Port 2
24
25
1
2
3
4
P1.5
I/O
I/O
I/O
I
Bit 5 of Port 1
Bit 6 of Port 1
Bit 7 of Port 1
Reset
Receive Data
Bit 0 of Port 3
No Connect
Transmit Data &
Bit 1 of Port 3
External Interrupt 0
Bit 2 of Port 3
External Interrupt 1
Bit 3 of Port 3
Bit 14 of External Memory Address
Bit 7 of Port 2
Bit 15 of External Memory Address
Program Store Enable
Address Latch Enable
No Connect
P1.6
P1.7
RES
RXD
P3.0
NC
TXD
P3.1
#INT0
P3.2
#INT1
P3.3
T0
26
27
28
29
I
5
6
7
I/O
-
O
I/O
I
I/O
I
External Access
Bit 7 Of Port 0
30
31
32
33
34
35
36
37
Data/Address Bit 7 of External Memory
Bit 6 of Port 0
Data/Address Bit 6 of External Memory
Bit 5 of Port 0
Data/Address Bit 5 of External Memory
Bit 4 of Port 0
Data/Address Bit 4 of External Memory
Bit 3 Of Port 0
8
9
I/O
I
Timer 0
10
11
12
13
P3.4
T1
I/O
I
I/O
O
I/O
O
I/O
O
Bit 4 of Port 3
Timer 1 & 3
Bit 5 of Port
Ext. Memory Write
Bit 6 of Port 3
Ext. Memory Read
Bit 7 of Port 3
Oscillator/Crystal Output
Oscillator/Crystal In
Ground
P3.5
#WR
P3.6
#RD
P3.7
XTAL2
XTAL1
VSS
NC
Data/Address Bit 3 of External Memory
Bit 2 of Port 0
Data/Address Bit 2 of External Memory
Bit 1 of Port 0 & Data
Address Bit 1 of External Memory
Bit 0 Of Port 0 & Data
Address Bit 0 of External Memory
VCC
14
15
16
17
I
-
-
38
39
No Connect
-
I
No Connect
P2.0
A8
P2.1
A9
P2.2
A10
P2.3
A11
P2.4
A12
P2.5
A13
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
Bit 0 of Port 2
Bit 8 of External Memory Address
Bit 1 of Port 2
Bit 9 of External Memory Address
Bit 2 of Port 2
Bit 10 of External Memory Address
Bit 3 of Port 2 &
Bit 11 of External Memory Address
Bit 4 of Port 2
Bit 12 of External Memory Address
Bit 5 of Port 2
T2
Timer 2 Clock Out
18
19
20
21
22
23
40
41
P1.0
T2EX
P1.1
P1.2
I/O
I
I/O
I/O
Bit 0 of Port 1
Timer 2 Control
Bit 1 of Port 1
Bit 2 of Port 1
42
43
P1.3
P1.4
I/O
I/O
Bit 3 of Port 1
Bit 4 of Port 1
44
Bit 13 of External Memory Address
33 32 31 30 29 28 27 26 25 24 23
34
22
P0.3/AD3
P0.2/AD2
P0.1/AD1
P2.4/A12
35
36
37
38
39
40
41
42
P2.3/A11
P2.2/A10
21
20
19
18
17
16
15
14
P0.0/AD0
VDD
P2.1/A9
P2.0/A8
VRS51x550/560
QFP-44
NC
T2/P1.0
T2EX/P1.1
P1.2
NC
VSS
XTAL1
XTAL2
43
44
P1.3
P1.4
#RD/P3.7
#WR/P3.6
13
12
11
9 10
2
3
4
5
6
7
8
1
________________________________________________________________________________________________
www.ramtron.com page 2 of 40
VRS51x550/560
Pin Descriptions for PLCC-44
TABLE 2: PIN DESCRIPTIONS FOR PLCC-44
PLCC
PLCC
- 44
Name
P2.0
A8
P2.1
A9
I/O
Function
Name
I/O
Function
- 44
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
Bit 0 of Port 2
1
NC
-
No Connect
24
25
26
27
28
29
30
31
Bit 8 of External Memory Address
Bit 1 of Port 2
Bit 9 of External Memory Address
Bit 2 of Port 2
Bit 10 of External Memory Address
Bit 3 of Port 2 &
Bit 11 of External Memory Address
Bit 4 of Port 2
Bit 12 of External Memory Address
Bit 5 of Port 2
Bit 13 of External Memory Address
Bit 6 of Port 2
Bit 14 of External Memory Address
Bit 7 of Port 2
Bit 15 of External Memory Address
Program Store Enable
Address Latch Enable
No Connect
T2
I
Timer 2 Clock Out
Bit 0 of Port 1
Timer 2 Control
Bit 1 of Port 1
Bit 2 of Port 1
Bit 3 of Port 1
Bit 4 of Port 1
Bit 5 of Port 1
Bit 6 of Port 1
Bit 7 of Port 1
Reset
Receive Data
Bit 0 of Port 3
No Connect
Transmit Data &
Bit 1 of Port 3
External Interrupt 0
Bit 2 of Port 3
External Interrupt 1
Bit 3 of Port 3
Timer 0
Bit 4 of Port 3
Timer 1 & 3
Bit 5 of Port
Ext. Memory Write
Bit 6 of Port 3
Ext. Memory Read
Bit 7 of Port 3
Oscillator/Crystal Output
Oscillator/Crystal In
Ground
2
3
P1.0
T2EX
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RES
RXD
P3.0
NC
TXD
P3.1
#INT0
P3.2
#INT1
P3.3
T0
I/O
I
P2.2
A10
P2.3
A11
P2.4
A12
P2.5
A13
P2.6
A14
P2.7
A15
#PSEN
ALE
NC
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
4
5
6
7
8
9
10
I
11
12
13
I/O
-
O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
O
I/O
O
32
33
34
35
O
O
-
I
14
15
16
17
18
19
#EA
P0.7
External Access
I/O
Bit 7 Of Port 0
36
37
38
39
40
Data/Address Bit 7 of External
Memory
AD7
P0.6
AD6
P0.5
AD5
P0.4
AD4
P0.3
AD3
P0.2
AD2
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
P3.4
T1
Bit 6 of Port 0
Data/Address Bit 6 of External
Memory
P3.5
#WR
P3.6
#RD
P3.7
XTAL2
XTAL1
VSS
NC
Bit 5 of Port 0
Data/Address Bit 5 of External
Memory
I/O
O
I
-
-
Bit 4 of Port 0
20
21
22
23
Data/Address Bit 4 of External
Memory
Bit 3 Of Port 0
No Connect
Data/Address Bit 3 of External
Memory
Bit 2 of Port 0
41
42
Data/Address Bit 2 of External
Memory
P0. 1
AD1
P0.0
AD0
VDD
I/O
I/O
I/O
I/O
-
Bit 1 of Port 0 & Data
Address Bit 1 of External Memory
Bit 0 Of Port 0 & Data
Address Bit 0 of External Memory
VCC
43
44
6
5
4
3
2
1
44 43 42 41 40
7
39
38
37
P1.5
P1.6
P1.7
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
#EA
8
9
36
35
10
11
RESET
RXD/P3.0
NC
VRS51x550/560
PLCC-44
34
33
32
31
12
13
14
15
NC
TXD/P3.1
#INT0/P3.2
#INT1/P3.3
ALE
#PSEN
P2.7/A15
P2.6/A14
P2.5/A13
30
29
16
T0/P3.4
T1/P3.5
17
18 19 20 21 22 23 24 25 26 27 28
________________________________________________________________________________________________
www.ramtron.com page 3 of 40
VRS51x550/560
Pin Descriptions for DIP-40
TABLE 3: PIN DESCRIPTIONS FOR DIP-40
DIP40
Name
T2
I/O
I
I/O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
Function
Timer 2 Clock Out
DIP40
Name
P2.0
A8
P2.1
A9
P2.2
A10
P2.3
A11
P2.4
A12
P2.5
A13
P2.6
A14
P2.7
A15
I/O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
I/O
O
Function
Bit 0 of Port 2
Bit 8 of External Memory Address
Bit 1 of Port 2
Bit 9 of External Memory Address
Bit 2 of Port 2
Bit 10 of External Memory Address
Bit 3 of Port 2 &
Bit 11 of External Memory Address
Bit 4 of Port 2
Bit 12 of External Memory Address
Bit 5 of Port 2
Bit 13 of External Memory Address
Bit 6 of Port 2
Bit 14 of External Memory Address
Bit 7 of Port 2
Bit 15 of External Memory Address
Program Store Enable
Address Latch Enable
External Access
Flash programming voltage input
Bit 7 Of Port 0
Data/Address Bit 7 of External
Memory
Bit 6 of Port 0
Data/Address Bit 6 of External
Memory
Bit 5 of Port 0
Data/Address Bit 5 of External
Memory
Bit 4 of Port 0
Data/Address Bit 4 of External
Memory
Bit 3 Of Port 0
Data/Address Bit 3 of External
Memory
Bit 2 of Port 0
Data/Address Bit 2 of External
Memory
Bit 1 of Port 0 & Data
Address Bit 1 of External Memory
Bit 0 Of Port 0 & Data
Address Bit 0 of External Memory
Supply input
1
21
P1.0
T2EX
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RESET
RXD
P3.0
TXD
P3.1
#INT0
P3.2
#INT1
P3.3
T0
Bit 0 of Port 1
Timer 2 Control
Bit 1 of Port 1
Bit 2 of Port 1
Bit 3 of Port 1
Bit 4 of Port 1
Bit 5 of Port 1
Bit 6 of Port 1
Bit 7 of Port 1
Reset
Receive Data
Bit 0 of Port 3
Transmit Data &
Bit 1 of Port 3
External Interrupt 0
Bit 2 of Port 3
External Interrupt 1
Bit 3 of Port 3
Timer 0
Bit 4 of Port 3
Timer 1 & 3
Bit 5 of Port
Ext. Memory Write
Bit 6 of Port 3
Ext. Memory Read
Bit 7 of Port 3
Oscillator/Crystal Output
Oscillator/Crystal In
Ground
2
22
23
24
25
26
27
28
3
4
5
6
7
8
9
I
10
11
12
13
14
15
16
17
I/O
O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
O
I/O
O
I/O
O
29
30
#PSEN
ALE
#EA /
VPP
P0.7
O
O
31
I
P3.4
T1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
32
AD7
P0.6
AD6
P0.5
AD5
P0.4
AD4
P0.3
AD3
P0.2
AD2
P3.5
#WR
P3.6
#RD
P3.7
XTAL2
XTAL1
VSS
33
34
35
36
18
19
20
I
-
T2 / P1.0
1
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
VDD
T2EX / P1.1
P1.2
2
P0.0 / AD0
P0.1 / AD1
P0.2 / AD2
P0.3 / AD3
P0.4 / AD4
P0.5 / AD5
P0.6 / AD6
P0.7 / AD7
#EA / VPP
ALE
37
38
3
P0. 1
AD1
P0.0
AD0
VDD
I/O
I/O
I/O
I/O
-
P1.3
4
P1.4
5
P1.5
39
40
6
P1.6
7
P1.7
8
RESET
RXD / P3.0
TXD / P3.1
#INT0 / P3.2
#INT1 / P3.3
T0 / P3.4
T1 / P3.5
#WR / P3.6
#RD / P3.7
XTAL2
9
VRS51x550
VRS51x560
DIP-40
10
11
12
13
14
15
16
17
18
19
20
PSEN
P2.7 / A15
P2.6 / A14
P2.5 / A13
P2.4 / A12
P2.3 / A11
P2.2 / A10
P2.1 / A9
P2.0 / A8
XTAL1
VSS
________________________________________________________________________________________________
www.ramtron.com page 4 of 40
VRS51x550/560
Instruction Set
Size
(bytes)
Mnemonic
Description
Instr. Cycles
The following tables describe the instruction set of the Boolean Instruction
CLR C
VRS51x550/560. The instructions are function and binary
CLR bit
Clear Carry bit
Clear bit
Set Carry bit to 1
Set bit to 1
Complement Carry bit
Complement bit
Logical AND between Carry and bit
Logical AND between Carry and not bit
Logical ORL between Carry and bit
Logical ORL between Carry and not bit
Copy bit value into Carry
Copy Carry value into Bit
1
2
1
2
1
2
2
2
2
2
2
2
1
1
1
1
1
1
2
2
2
2
1
2
SETB C
SETB bit
code compatible with industry standard 8051s.
TABLE 4: LEGEND FOR INSTRUCTION SET TABLE
CPL C
CPL bit
Symbol
A
Rn
Direct
@Ri
rel
Function
Accumulator
Register R0-R7
Internal register address
Internal register pointed to by R0 or R1 (except MOVX)
Two's complement offset byte
Direct bit address
8-bit constant
16-bit constant
ANL C,bit
ANL C,#bit
ORL C,bit
ORL C,#bit
MOV C,bit
MOV bit,C
Data Transfer Instructions
MOV A, Rn
MOV A, direct
MOV A, @Ri
MOV A, #data
MOV Rn, A
bit
#data
#data 16
addr 16
addr 11
Move register to A
Move direct byte to A
Move data memory to A
Move immediate to A
1
2
1
2
1
2
2
2
2
3
2
3
1
2
2
3
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
2
1
1
2
2
2
2
1
2
1
2
2
2
2
2
2
2
2
2
1
1
1
1
16-bit destination address
11-bit destination address
Move A to register
TABLE 5: VRS51X550/VRS51X560 INSTRUCTION SET
MOV Rn, direct
MOV Rn, #data
MOV direct, A
MOV direct, Rn
MOV direct, direct
MOV direct, @Ri
MOV direct, #data
MOV @Ri, A
MOV @Ri, direct
MOV @Ri, #data
MOV DPTR, #data
MOVC A, @A+DPTR
Move direct byte to register
Move immediate to register
Move A to direct byte
Move register to direct byte
Move direct byte to direct byte
Move data memory to direct byte
Move immediate to direct byte
Move A to data memory
Move direct byte to data memory
Move immediate to data memory
Move immediate to data pointer
Move code byte relative DPTR to A
Move code byte relative PC to A
Move external data (A8) to A
Move external data (A16) to A
Move A to external data (A8)
Move A to external data (A16)
Push direct byte onto stack
Pop direct byte from stack
Exchange A and register
Size
(bytes)
Mnemonic
Description
Instr. Cycles
Arithmetic instructions
ADD A, Rn
ADD A, direct
ADD A, @Ri
ADD A, #data
ADDC A, Rn
ADDC A, direct
ADDC A, @Ri
ADDC A, #data
SUBB A, Rn
SUBB A, direct
SUBB A, @Ri
SUBB A, #data
INC A
INC Rn
INC direct
INC @Ri
DEC A
DEC Rn
DEC direct
DEC @Ri
INC DPTR
MUL AB
Add register to A
Add direct byte to A
Add data memory to A
Add immediate to A
Add register to A with carry
Add direct byte to A with carry
Add data memory to A with carry
Add immediate to A with carry
Subtract register from A with borrow
Subtract direct byte from A with borrow
Subtract data mem from A with borrow
Subtract immediate from A with borrow
Increment A
Increment register
Increment direct byte
Increment data memory
Decrement A
Decrement register
Decrement direct byte
Decrement data memory
Increment data pointer
Multiply A by B
Divide A by B
Decimal adjust A
1
2
1
2
1
2
1
2
1
2
1
2
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
4
1
MOVC A, @A+PC
MOVX A, @Ri
MOVX A, @DPTR
MOVX @Ri, A
MOVX @DPTR, A
PUSH direct
POP direct
XCH A, Rn
XCH A, direct
XCH A, @Ri
XCHD A, @Ri
Branching Instructions
ACALL addr 11
LCALL addr 16
RET
Exchange A and direct byte
Exchange A and data memory
Exchange A and data memory nibble
Absolute call to subroutine
Long call to subroutine
Return from subroutine
Return from interrupt
Absolute jump unconditional
Long jump unconditional
Short jump (relative address)
Jump on carry = 1
Jump on carry = 0
Jump on direct bit = 1
Jump on direct bit = 0
Jump on direct bit = 1 and clear
Jump indirect relative DPTR
Jump on accumulator = 0
Jump on accumulator 1= 0
Compare A, direct JNE relative
Compare A, immediate JNE relative
Compare reg, immediate JNE relative
Compare ind, immediate JNE relative
Decrement register, JNZ relative
Decrement direct byte, JNZ relative
2
3
1
1
2
3
2
2
2
3
3
3
1
2
2
3
3
3
3
2
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
DIV AB
DA A
RETI
AJMP addr 11
LJMP addr 16
SJMP rel
JC rel
JNC rel
JB bit, rel
JNB bit, rel
JBC bit, rel
JMP @A+DPTR
JZ rel
Logical Instructions
ANL A, Rn
ANL A, direct
ANL A, @Ri
ANL A, #data
ANL direct, A
ANL direct, #data
ORL A, Rn
ORL A, direct
ORL A, @Ri
ORL A, #data
ORL direct, A
ORL direct, #data
XRL A, Rn
XRL A, direct
XRL A, @Ri
XRL A, #data
XRL direct, A
XRL direct, #data
CLR A
AND register to A
AND direct byte to A
AND data memory to A
AND immediate to A
AND A to direct byte
AND immediate data to direct byte
OR register to A
OR direct byte to A
OR data memory to A
OR immediate to A
OR A to direct byte
OR immediate data to direct byte
Exclusive-OR register to A
Exclusive-OR direct byte to A
Exclusive-OR data memory to A
Exclusive-OR immediate to A
Exclusive-OR A to direct byte
Exclusive-OR immediate to direct byte
Clear A
Compliment A
Swap nibbles of A
Rotate A left
Rotate A left through carry
Rotate A right
1
2
1
2
2
3
1
2
1
2
2
3
1
2
1
2
2
3
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
JNZ rel
CJNE A, direct, rel
CJNE A, #d, rel
CJNE Rn, #d, rel
CJNE @Ri, #d, rel
DJNZ Rn, rel
DJNZ direct, rel
Miscellaneous Instruction
NOP No operation
1
1
Rn:
@Ri:
Any of the register R0 to R7
Indirect addressing using Register R0 or R1
CPL A
SWAP A
RL A
RLC A
RR A
RRC A
#data: immediate Data provided with Instruction
#data16: Immediate data included with instruction
address at the bit level
relative address to Program counter from +127 to –128
Addr11: 11-bit address range
Addr16: 16-bit address range
bit:
rel:
Rotate A right through carry
#d:
Immediate Data supplied with instruction
________________________________________________________________________________________________
www.ramtron.com page 5 of 40
VRS51x550/560
Special Function Registers (SFR)
Addresses 80h to FFh of the SFR address space can be accessed in direct addressing mode only. The following table
lists the VRS51x550/560 special function registers.
TABLE 6: SPECIAL FUNCTION REGISTERS (SFR)
SFR
Register
SFR
Adrs
80h
81h
82h
83h
84h
87h
88h
89h
8Ah
8Bh
8Ch
8Dh
90h
98h
99h
9Fh
A0h
A8h
B0h
B8h
BFh
C8h
CAh
CBh
CCh
CDh
D0h
E0h
F0h
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset Value
P0
SP
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
DPL
DPH
Reserved
PCON
TCON
TMOD
TL0
SMOD
TF1
GATE1
-
-
-
GF1
IE1
GATE0
GF0
IT1
C/T0
-
-
-
-
-
PDOWN
IE0
M1.0
-
IDLE
IT0
M0.0
-
-
-
-
-
00000000b
00000000b
00000000b
TR1
C/T1
-
-
-
-
-
SM1
-
-
-
-
-
-
-
TF0
M1.1
-
-
-
-
-
SM2
-
WDCLR
TR0
M0.1
-
-
-
-
-
REN
-
-
-
ES
-
PS
-
-
-
-
-
-
-
-
-
TL1
-
-
-
-
TI
-
TH0
TH1
P1
-
-
SCON
SBUF
WDTCON
P2
SM0
-
WDTE
-
EA
-
-
TB8
-
-
-
ET1
-
PT1
-
RB8
-
WDPS2
RI
-
WDPS0
00000000b
0*0**000b
00000000b
WDPS1
-
-
-
-
IE
P3
IP
ET2
-
PT2
-
EX1
-
PX1
ET0
-
PT0
EX0
-
PX0
ALEI
00000000b
0******0b
00000000b
00000000b
SYSCON
T2CON
RCAP2L
RCAP2H
TL2
TH2
PSW
ACC
WDRESET
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
CY
-
-
AC
-
-
F0
-
-
RS1
-
-
RS0
-
-
OV
-
-
-
-
-
P
-
-
00000000b
B
______________________________________________________________________________________________
www.ramtron.com page 6 of 40
VRS51x550/560
Program Memory
Program Memory
Data Pointer
The VRS51x550 and VRS51x560 each have one 16-bit
data pointer. The DPTR is accessed through two SFR
addresses: DPL located at address 82h and DPH
located at address 83h.
The VRS51x550 includes 8KB of on-chip Program
Flash memory. The VRS51x560 includes 16KB
Program Flash memory.
Data Memory
FIGURE 3: VRS51X560 / VRS51X550 INTERNAL PROGRAM MEMORY
The VRS51x550 and VRS51x560 each have a total of:
256 bytes of RAM configured like the internal memory
structure of a standard 8052.
3FFFh
FIGURE 4: VRS51X550 /VRS51X560 RAM MEMORY OVERVIEW
VRS51x560
Flash Memory
(16K Bytes)
1FFFh
RM51x550
Flash Memory
(8K Bytes)
0000h
0000h
Lower 128 bytes (00h to 7Fh, Bank 0 & Bank 1)
Program Status Word Register
The lower 128 bytes of data memory (from 00h to 7Fh)
is summarized as follows:
The PSW register is a bit addressable register that
contains the status flags (CY, AC, OV, P), user flag
(F0) and register bank select bits (RS1, RS0) of the
8051 processor.
·
·
Address range 00h to 7Fh can be accessed in
direct and indirect addressing modes.
Address range 00h to 1Fh includes R0-R7
registers area.
TABLE 7: PROGRAM STATUS WORD REGISTER (PSW) - SFR DOH
·
·
Address range 20h to 2Fh is bit addressable.
Address range 30h to 7Fh is not bit addressable
and can be used as general-purpose storage.
7
CY
6
AC
5
F0
4
RS1
3
RS0
2
OV
1
-
0
P
Bit
Mnemonic Description
Upper 128 bytes (80h to FFh, Bank 2 & Bank 3)
7
6
5
4
3
2
1
0
CY
AC
F0
Carry Bit
Auxiliary Carry Bit from bit 3 to 4.
User definer flag
The upper 128 bytes of data memory (from 80h to FFh)
can be accessed using indirect addressing or by using
the bank mapping in direct addressing mode.
RS1
RS0
OV
-
R0-R7 Registers bank select bit 0
R0-R7 Registers bank select bit 1
Overflow flag
FIGURE 5: VRS51X550 / VRS51X560 RAM STRUCTURE
-
P
Parity flag
FFh
FFh
SFR Area
Direct or Bit Access
RS1
RS0
Active Bank
Address
Only
128 Bytes of
Indirect Access RAM
(SP, R0,R1)
DPH
0
0
1
1
0
1
0
1
0
1
2
3
00h-07h
08h-0Fh
10h-17h
18-1Fh
DPL
SP
85
84
83
82
81
80
P0
80h
7Fh
80 Bytes of
General Purpose RAM
30h
2Fh
7F
77
7E
76
7D
75
7C
74
7B
73
7A
72
79
71
78
70
0F
07
0E
06
0D
05
0C
04
0B
03
0A
02
09
01
08
00
20h
R7
-
R0
R7
-
R0
R7
-
R0
R7
-
Registers Bank 3
Registers Bank 2
Registers Bank 1
Registers Bank 0
18h
10h
08h
00h
R0
______________________________________________________________________________________________
www.ramtron.com page 7 of 40
VRS51x550/560
Description of Peripherals
System Control Register
These power saving modes are controlled by the
PDOWN and IDLE bits of the PCON register at
address 87h.
The SYSCON register is used for system control and is
described in the following table.
TABLE 9: POWER CONTROL REGISTER (PCON) - SFR 87H
7
6
5
4
3
2
1
0
The WDRESET bit (7) indicates whether the system
has been reset due to overflow of the watchdog timer.
Unused
RAM1
RAM0
Bit
7
Mnemonic Description
Bit 0 of the SYSCON register is the ALE output inhibit
bit. Setting this bit to 1 will inhibit the Fosc/6 clock
signal output to the ALE pin.
SMOD
1: Double the baud rate of the serial port
frequency that was generated by Timer 1.
0: Normal serial port baud rate generated by
Timer 1.
TABLE 8: SYSTEM CONTROL REGISTER (SYSCON) – SFR BFH
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
ALEI
WDRESET
XRAME
Unused
GF1
GF0
PDOWN
IDLE
General Purpose Flag
General Purpose Flag
Power Down mode control bit
Idle mode control bit
Bit
7
Mnemonic Description
WDRESET
This is the watchdog timer reset bit. It
will be set to 1 when the reset signal
generated by WDT overflows.
6
5
4
3
2
1
0
Unused
Unused
Unused
Unused
Unused
Unused
ALEI
-
-
-
-
-
-
ALE output inhibit bit, which is used to
reduce EMI.
Power Control Register
VRS51x550/560 devices provide two power saving
modes: Idle and Power Down. These two modes serve
to reduce the power consumption of the device.
In Idle mode, the processor is stopped but the oscillator
continues to run. The contents of the RAM, I/O state
and SFR registers are maintained and the timer and
external interrupts are left operational. The processor
will be woken up when an external event, triggering an
interrupt, occurs.
In Power Down mode, the VRS51x550/560 oscillator
and peripherals are disabled. The contents of the RAM
and the SFR registers, however, are maintained.
The minimum VCC in Power Down mode is 2V.
______________________________________________________________________________________________
www.ramtron.com page 8 of 40
VRS51x550/560
FIGURE 6: INTERNAL STRUCTURE OF ONE OF THE EIGHT I/O PORT LINES
Input/Output Ports
Read Register
The VRS51x550 and VRS51x560 each have a total of
32 bi-directional I/O lines grouped into four 8-bit I/O
ports. These I/Os can be individually configured as
inputs or outputs.
With the exception of the P0 I/Os, which are of the
open drain type, each I/O consists of a transistor
connected to ground and a weak pull-up resistor.
Q
Internal Bus
IC Pin
Output
D Flip-Flop
Stage
Write to
Register
Q
Writing a 0 in a given I/O port bit register will activate
the transistor connected to Vss. This will bring the I/O
to a LOW level.
Read Pin
Writing a 1 into a given I/O port bit register deactivates
the transistor between the pin and ground. In this case,
the pull-up resistor will bring the corresponding pin to a
HIGH level.
Structure of the P1, P2, P3
The following figure describes the general structure of
the P1, P2 and P3 ports. Note that the figure below
does not show the intermediary logic that connects the
register output with the output stage because this logic
varies with the auxiliary function of each port.
To use a given I/O as an input, a 1 must be written into
its associated port register bit. By default, upon reset
all the I/Os are configured as inputs.
General Structure of an I/O Port
FIGURE 7: GENERAL STRUCTURE OF THE OUTPUT STAGE OF P1, P2 AND P3
The following elements establish the link between the
core unit and the pins of the microcontroller:
Read Register
·
·
Special Function Register (same name as port)
Output Stage Amplifier (the structure of this
element varies with its auxiliary function)
Vcc
Pull-up
Network
From the next figure, one can see that the D flip-flop
stores the value received from the internal bus after
receiving a write signal from the core. Also, note that
the Q output of the flip-flop can be linked to the internal
bus by executing a read instruction.
Q
Internal Bus
IC Pin
D Flip-Flop
Write to
Register
X1
Q
This is how one would read the content of the register.
It is also possible to link the value of the pin to the
internal bus. This is done by the “read pin” instruction.
In short, the user may read the value of the register or
the pin.
Read Pin
Each line may be used independently as a logical
input or output. When used as an input, the
corresponding port register bit must be high.
______________________________________________________________________________________________
www.ramtron.com page 9 of 40
VRS51x550/560
Structure of Port 0
Port P0 and P2 as Address and Data Bus
The internal structure of P0 is shown below. The
auxiliary function of this port requires a particular logic.
As opposed to the other ports, P0 is truly bi-directional.
In other words, when used as an input, it is considered
to be in a floating logical state (high impedance state).
This arises from the absence of the internal pull-up
resistance. The pull-up resistance is actually replaced
by a transistor that is only used when the port is
configured to access the external memory/data bus
(EA=0).
The output stage may receive data from two sources:
·
·
The outputs of register P0 or the bus address
itself multiplexed with the data bus for P0
The outputs of the P2 register or the high byte
(A8 through A15) of the bus address for the P2
port
FIGURE 9: P2 PORT STRUCTURE
When used as an I/O port, P0 acts as an open drain
port and the use of an external pull-up resistor is likely
to be required for most applications.
Read Register
Vcc
Address
Pull-up
Network
FIGURE 8: PORT P0’S PARTICULAR STRUCTURE
Q
Q
Internal Bus
IC Pin
D Flip-Flop
Address A0/A7
Write to
Register
X1
Read Register
Control
Control
Vcc
Read Pin
Q
Internal Bus
IC Pin
When the ports are used as an address or data bus,
the special function registers P0 and P2 are
disconnected from the output stage. The 8 bits of the
P0 register are forced to 1 and the content of the P2
register remains constant.
D Flip-Flop
X1
Write to
Register
Q
Read Pin
Auxiliary Port 1 Functions
When P0 is used as an external memory bus input (for
a MOVX instruction, for example), the outputs of the
register are automatically forced to 1.
The Port 1 I/O pins are shared with the T2EX and T2
inputs as shown below:
Pin
Mnemonic Function
P1.0 T2
P1.1 T2EX
Timer 2 counter input
Timer 2 Auxiliary input
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
______________________________________________________________________________________________
www.ramtron.com page 10 of 40
VRS51x550/560
Auxiliary P3 Port Functions
Software Particularities Concerning the Ports
Some instructions allow the user to read the logic state
of the output pin, while others allow the user to read
the content of the associated port register. These
instructions are called read-modify-write instructions. A
list of these instructions may be found in the table
below.
The Port 3 I/O pins are shared with the UART
interface, the INT0 and INT1 interrupts, the Timer 0
and Timer 1 inputs and the #WR and #RD lines when
external memory access is performed.
FIGURE 10: P3 PORT STRUCTURE
Upon execution of these instructions, the content of the
port register (at least 1 bit) is modified. The other read
instructions take the present state of the input into
account. For example, the instruction ANL P3, #01h
obtains the value in the P3 register; performs the
desired logic operation with the constant 01h; and
recopies the result into the P3 register. When users
want to take the present state of the inputs into
account, they must first read these states and perform
an AND operation between the reading and the
constant.
Auxiliary
Function: Output
Read Register
Vcc
IC Pin
X1
Q
Internal Bus
D Flip-Flop
Write to
Register
Q
Read Pin
Auxiliary
Function: Input
MOV A, P3; State of the inputs in the accumulator
ANL A, #01; AND operation between P3 and 01h
The following table describes the auxiliary function of
the Port 3 I/O pins.
When the port is used as an output, the register
contains information on the state of the output pins.
Measuring the state of an output directly on the pin is
inaccurate because the electrical level depends mostly
on the type of charge that is applied to it. The functions
shown below take the value of the register rather than
that of the pin.
TABLE 10: P3 AUXILIARY FUNCTION TABLE
Pin
Mnemonic Function
P3.0 RXD
Serial Port:
Receive data in asynchronous
mode. Input and output data in
synchronous mode.
P3.1 TXD
Serial Port:
TABLE 11: LIST OF INSTRUCTIONS THAT READ AND MODIFY THE PORT USING REGISTER
VALUES
Transmit data in asynchronous
mode. Output clock value in
synchronous mode.
External Interrupt 0
Timer 0 Control Input
External Interrupt 1
Timer 1 Control Input
Timer 0 Counter Input
Timer 1 Counter Input
Write signal for external memory
Instruction Function
ANL
ORL
XRL
JBC
CPL
INC
Logical AND ex: ANL P0, A
P3.2
INT0
Logical OR ex: ORL P2, #01110000B
Exclusive OR ex: XRL P1, A
Jump if the bit of the port is set to 0
Complement one bit of the port
Increment the port register by 1
Decrement the port register by 1
Decrement by 1 and jump if the result
is not equal to 0
P3.3
INT1
P3.4 T0
P3.5 T1
DEC
DJNZ
P3.6
WR
P3.7
RD
Read signal for external memory
MOV P., C Copy the held bit C to the port
CLR P.x
SETB P.x
Set the port bit to 0
Set the port bit to 1
______________________________________________________________________________________________
www.ramtron.com page 11 of 40
VRS51x550/560
Reading a Port (Input)
Port Operation Timing
Writing to a Port (Output)
The reading of an I/O pin takes place:
·
·
·
During T9 cycle for P0, P1
During T10 cycle for P2, P3
When the ports are configured as I/Os (see
Figure 25)
When an operation results in a modification of the
content in a port register, the new value is placed at the
output of the D flip-flop during the T12 period of the last
machine cycle that the instruction needed to execute.
In order to be sampled, the signal duration present on
the I/O inputs must be longer than Fosc/12.
It is important to note, however, that the output stage
only samples the output of the registers on the P1
phase of each period. It follows that the new value only
appears at the output after the T12 period of the
following machine cycle.
I/O Ports Driving Capability
The maximum allowable continuous current that the
device can sink on an I/O port is defined by the
following:
Maximum sink current on one given I/O
Maximum total sink current for P0
Maximum total sink current for P1, 2, 3
Maximum total sink current on all I/O
10mA
26mA
15mA
70mA
It is not recommended to exceed the sink current
outlined in the above table. Doing so will likely make
the low-level output voltage exceed the device’s
specification and will likely affect device reliability.
The VRS51x550/VRS51x560 I/O ports are not
designed to source current.
______________________________________________________________________________________________
www.ramtron.com page 12 of 40
VRS51x550/560
TABLE 12: TIMER MODE CONTROL REGISTER (TMOD) – SFR 89H
Timers
7
6
5
4
3
2
1
0
GATE
C/T
M1
M0
GATE
C/T
M1.0
M0.0
The VRS51x550 and VRS51x560 each include three
16-bit timers: T0, T1 and T2.
Bit
7
Mnemonic Description
GATE1
1: Enables external gate control (pin INT1 for
Counter 1). When INT1 is high, and TRx bit is
set (see TCON register), a counter is
incremented every falling edge on the T1IN
input pin.
The timers can operate in two specific modes:
·
·
Event counting mode
Timer mode
6
C/T1
Selects timer or counter operation (Timer 1).
1 = A counter operation is performed
0 = The corresponding register will function
as a timer.
When operating in counting mode, the counter is
incremented each time an external event, such as a
transition in the logical state of the timer input (T0, T1,
T2 input), is detected. When operating in timer mode,
the counter is incremented by the microcontroller’s
direct clock pulse or by a divided version of this pulse.
Selects mode for Timer/Counter 1
5
4
3
M1.1
Selects mode for Timer/Counter 1
M0.1
If set, enables external gate control (pin INT0
for Counter 0). When INT0 is high, and TRx
bit is set (see TCON register), a counter is
incremented every falling edge on the T0IN
input pin.
GATE0
Timer 0 and Timer 1
Selects timer or counter operation (Timer 0).
1 = A counter operation is performed
0 = The corresponding register will function
as a timer.
2
C/T0
Timers 0 and 1 have four modes of operation. These
modes allow the user to change the size of the
counting register or to authorize an automatic reload
when provided with a specific value. Timer 1 can also
be used as a baud rate generator to generate
communication frequencies for the serial interface.
Selects mode for Timer/Counter 0.
1
0
M1.0
M0.0
Selects mode for Timer/Counter 0.
The table below summarizes the four modes of
operation of timers 0 and 1. The timer-operating mode
is selected by the bits M1 and M0 of the TMOD
register.
Timer 0 and Timer 1 are configured by the TMOD and
TCON registers.
TABLE 13: TIMER/COUNTER MODE DESCRIPTION SUMMARY
M1 M0 Mode Function
0
0
1
0
1
0
Mode 0
Mode 1
Mode 2
13-bit Counter
16-bit Counter
8-bit auto-reload Counter/Timer. The reload
value is kept in TH0 or TH1, while TL0 or TL1
is incremented every machine cycle. When TLx
overflows, the value of THx is copied to TLx.
If Timer 1 M1 and M0 bits are set to 1, Timer 1
stops.
1
1
Mode 3
______________________________________________________________________________________________
www.ramtron.com page 13 of 40
VRS51x550/560
Operating Modes
Timer 0/Timer 1 Counter/Timer Functions
Timing Function
The user may change the operating mode by varying
the M1 and M0 bits of the TMOD SFR.
When operating as a timer, the counter is automatically
incremented at every system cycle (Fosc/12). A flag is
raised in the event of an overflow and the counter
acquires a value of zero. These flags (TF0 and TF1)
are located in the TCON register.
Mode 0
A schematic representation of this mode of operation
can be found in Figure 11. From the figure, we notice
that the timer operates as an 8-bit counter preceded by
a divide-by-32 prescaler composed of the 5LSBs of
TL1. The register of the counter is configured to be 13
bits long. When an overflow causes the value of the
register to roll over to 0, the TFx interrupt signal goes
to 1. The count value is validated as soon as TRx goes
to 1 and the GATE bit is 0, or when INTx is 1.
TABLE 14: TIMER 0 AND 1 CONTROL REGISTER (TCON) –SFR 88H
7
TF1
6
TR1
5
TF0
4
TR0
3
IE1
2
IT1
1
IE0
0
IT0
Bit
Mnemonic Description
7
TF1
Timer 1 Overflow Flag. Set by hardware on
Timer/Counter overflow. Cleared by
hardware on Timer/Counter overflow.
Cleared by hardware when processor
vectors to interrupt routine.
FIGURE 11: TIMER/COUNTER 1 MODE 0: 13-BIT COUNTER
6
TR1
TF0
Timer 1 Run Control Bit. Set/cleared by
software to turn Timer/Counter on or off.
Timer 0 Overflow Flag. Set by hardware on
Timer/Counter overflow. Cleared by
hardware when processor vectors to
interrupt routine.
5
CLK
÷12
TL1
4
0
1
C/T =0
C/T =1
0
7
CLK
Timer 0 Run Control Bit. Set/cleared by
software to turn Timer/Counter on or off.
Interrupt Edge Flag. Set by hardware when
external interrupt edge is detected. Cleared
when interrupt processed.
4
3
TR0
IE1
Mode 0
Control
T1PIN
Mode 1
TR1
GATE
TH1
0
7
Interrupt 1 Type Control Bit. Set/cleared by
software to specify falling edge/low level
triggered external interrupts.
Interrupt 0 Edge Flag. Set by hardware
when external interrupt edge is detected.
Cleared when interrupt processed.
Interrupt 0 Type control bit. Set/cleared by
software to specify falling edge/low level
triggered external interrupts.
2
1
0
IT1
IE0
IT0
INT1 PIN
TF1
INT
Mode 1
Mode 1 is almost identical to Mode 0. They differ in that
in Mode 1, the counter uses the full 16 bits and has no
prescaler.
Counting Function
Mode 2
When operating as a counter, the timer’s register is
incremented at every falling edge of the T0, T1 and T2
signals located at the input of the timer. In this case,
the signal is sampled at the T10 phase of each
machine cycle for Timer 0, Timer 1 and at T9 for Timer
2.
In this mode, the register of the timer is configured as
an 8-bit automatically re-loadable counter. In Mode 2, it
is the lower byte TLx that is used as the counter. In the
event of a counter overflow, the TFx flag is set to 1 and
the value contained in THx, which is preset by
software, is reloaded into the TLx counter. The value of
THx remains unchanged.
When the sampler sees a high immediately followed by
a low in the next machine cycle, the counter is
incremented. Two machine cycles are required to
detect and record an event. This reduces the counting
frequency by a factor of 24 (24 times less than the
oscillator’s frequency).
______________________________________________________________________________________________
www.ramtron.com page 14 of 40
VRS51x550/560
FIGURE 12: TIMER/COUNTER 1 MODE 2: 8-BIT AUTOMATIC RELOAD
CLK
÷12
C/T =0
C/T=1
TL1
0
1
0
7
Control
T1 Pin
Reload
0
7
TH1
TF1
TR1
GATE
INT
INT0 PIN
Mode 3
In Mode 3, Timer 1 is blocked as if its control bit, TR1,
was set to 0. In this mode, Timer 0’s registers TL0 and
TH0 are configured as two separate 8-bit counters.
Additionally, the TL0 counter uses Timer 0’s control
bits C/T, GATE, TR0, INT0, TF0 and the TH0 counter
is held in Timer Mode (counting machine cycles) and
gains control over TR1 and TF1 from Timer 1. At this
point, TH0 controls the Timer 1 interrupt.
FIGURE 13: TIMER/COUNTER 0 MODE 3
TH0
0
7
CLK
Control
TF1
INTERRUPT
TR1
CLK
÷12
TL0
0
1
C/T =0
C/T =1
0
7
CLK
Control
T0PIN
TF0
INTERRUPT
TR0
GATE
INT0 PIN
______________________________________________________________________________________________
www.ramtron.com page 15 of 40
VRS51x550/560
Capture/Reload Select.
0
Timer 2
1: Capture of Timer 2 value into RCAP2H,
RCAP2L is performed if EXEN2=1 and a
negative transitions occurs on the T2EX
pin. The capture mode requires RCLK and
TCLK to be 0.
CP/RL2
Timer 2 is a 16-bit Timer/Counter. Similar to timers 0
and 1, Timer 2 can operate as either an event counter
or as a timer. The user may switch functions by writing
to the C/T2 bit located in the T2CON special function
register. Timer 2 has three operating modes: “Auto-
Load” “Capture”, and “Baud Rate Generator”. The
T2CON SFR configures the modes of operation of
Timer 2. The following table describes each bit in the
T2CON special function register.
0: Auto-reload reloads will occur either with
Timer 2 overflows or negative transitions at
T2EX when EXEN2=1. When either RCK
=1 or TCLK =1, this bit is ignored and the
timer is forced to auto-reload on Timer 2
overflow.
As shown below, there are different combinations of
control bits that may be used for the mode selection of
Timer 2.
TABLE 15: TIMER 2 CONTROL REGISTER (T2CON) –SFR C8H
7
6
EXF2
5
4
3
2
1
C/T2
0
TF2
RCLK
TCLK
EXEN2
TR2
CP/RL2
TABLE 16: TIMER 2 MODE SELECTION BITS
Bit
7
Mnemonic Description
CP/RL2
0
RCLK + TCLK
0
TR2 MODE
Timer 2 Overflow Flag: Set by an overflow
of Timer 2 and must be cleared by
software. TF2 will not be set when either
RCLK =1 or TCLK =1.
TF2
16-bit Auto-
1
1
Reload Mode
16-bit Capture
Mode
0
1
Timer 2 external flag change in state occurs
when either a capture or reload is caused
by a negative transition on T2EX and
EXEN2=1. When Timer 2 is enabled,
EXF=1 will cause the CPU to Vector to the
Timer 2 interrupt routine. Note that EXF2
must be cleared by software.
6
EXF2
Baud Rate
Generator Mode
Off
1
X
X
1
0
X
The details of each mode are described below.
Serial Port Receive Clock Source.
1: Causes Serial Port to use Timer 2
overflow pulses for its receive clock in
modes 1 and 3.
5
4
3
RCLK
TCLK
Capture Mode
In capture mode the EXEN2 bit value defines whether
the external transition on the T2EX pin will be able to
trigger the capture of the timer value.
0: Causes Timer 1 overflow to be used for
the Serial Port receive clock.
Serial Port Transmit Clock.
1: Causes Serial Port to use Timer 2
overflow pulses for its transmit clock in
modes 1 and 3.
When EXEN2 = 0, Timer 2 acts as a 16-bit timer or
counter, which, upon overflowing, will set bit TF2
(Timer 2 overflow bit). This overflow can be used to
generate an interrupt.
0: Causes Timer 1 overflow to be used for
the Serial Port transmit clock.
Timer 2 External Mode Enable.
1: Allows a capture or reload to occur as a
result of a negative transition on T2EX if
Timer 2 is not being used to clock the Serial
Port.
EXEN2
FIGURE 14: TIMER 2 IN CAPTURE MODE
FOSC
÷12
0: Causes Timer 2 to ignore events at
T2EX.
Start/Stop Control for Timer 2.
1: Start Timer 2
0
1
TIMER
TL2
TH2
0
0
7
7
0
0
7
7
C/T2
2
1
TR2
COUNTER
T2 Pin
0: Stop Timer 2
RCAP2L
RCAP2H
TR2
Timer or Counter Select (Timer 2)
1: External event counter falling edge
triggered.
C/T2
TF2
T2 EX Pin
EXF2
0: Internal Timer (OSC/12)
EXEN2
Timer 2
Interrupt
When EXEN2 = 1, the above still applies. In addition, it
is possible to allow a 1 to 0 transition at the T2EX input
to cause the current value stored in the Timer 2
registers (TL2 and TH2) to be captured by the RCAP2L
______________________________________________________________________________________________
www.ramtron.com page 16 of 40
VRS51x550/560
and RCAP2H registers. Furthermore, the transition at
T2EX causes bit EXF2 in T2CON to be set, and EXF2,
like TF2, can generate an interrupt. Note that both
EXF2 and TF2 share the same interrupt vector.
Baud Rate Generator Mode
The baud rate generator mode is activated when RCLK
is set to 1 and/or TCLK is set to 1. This mode will be
described in the serial port section.
Auto-Reload Mode
FIGURE 16: TIMER 2 IN AUTOMATIC BAUD GENERATOR MODE
In this mode, there are also two options. The user may
choose either option by writing to bit EXEN2 in T2CON.
FOSC
÷2
If EXEN2 = 0, when Timer 2 rolls over, it not only sets
TF2, but also causes the Timer 2 registers to be
reloaded with the 16-bit value in the RCAP2L and
RCAP2H registers previously initialised. In this mode,
Timer 2 can be used as a baud rate generator source
for the serial port.
0
1
TIMER
TL2
TH2
0
0
7
0
0
7
C/T2
COUNTER
T2 Pin
7
7
RCAP2L
RCAP2H
TR2
1
0
TX Clock
RX Clock
÷16
÷16
TCLK
1
0
1
0
Timer 1 Overflow
÷2
RCLK
If EXEN2=1, then Timer 2 still performs the above
operation, but a 1 to 0 transition at the external T2EX
input will also trigger an anticipated reload of the Timer
2 with the value stored in RCAP2L, RCAP2H, and set
EXF2.
SMOD
Timer
2
Interrupt
Request
T2 EX Pin
EXF2
EXEN2
FIGURE 15: TIMER 2 IN AUTO-RELOAD MODE
FOSC
÷12
0
1
TIMER
TL2
TH2
0
0
7
7
0
0
7
7
C/T2
COUNTER
T2 Pin
RCAP2L
RCAP2H
TR2
TF2
T2 EX Pin
EXF2
EXEN2
Timer 2
Interrupt
______________________________________________________________________________________________
www.ramtron.com page 17 of 40
VRS51x550/560
9th data bit received in modes 2 and 3.
2
1
RB8
TI
Serial Port
In Mode 1, if SM2 = 0, RB8 is the stop bit
that was received.
In Mode 0, this bit is not used.
This bit must be cleared by software.
Transmission Interrupt flag.
The serial port included in the VRS51x550 and the
VRS51x560 can operate in full duplex; in other words,
it can transmit and receive data simultaneously. This
occurs at the same speed if one timer is assigned as
the clock source for both transmission and reception,
and at different speeds if transmission and reception
are each controlled by their own timer.
Automatically set to 1 when:
· The 8th bit has been sent in Mode 0.
· Automatically set to 1 when the stop bit
has been sent in the other modes.
This bit must be cleared by software.
Reception Interrupt flag
The serial port receive is buffered, which means that it
can begin reception of a byte even if the processor has
not retrieved the last byte from the receive register.
However, if the previously received byte has not been
read by the time reception of the next byte is complete,
the byte present in the receive buffer will be lost.
0
RI
Automatically set to 1 when:
· The 8th bit has been received in Mode 0.
· Automatically set to 1 when the stop bit
has been sent in the other modes (see
SM2 exception).
This bit must be cleared by software.
The SBUF register provides access to the transmit and
receive registers of the serial port. Reading from the
SBUF register will access the receive register, while a
write to the SBUF loads the transmit register..
TABLE 18: SERIAL PORT MODES OF OPERATION
SM0
0
0
SM1
0
1
Mode
Description
Baud Rate
Fosc/12
Variable
Fosc/64 or
Fosc/32
0
1
2
Shift Register
8-bit UART
9-bit UART
Serial Port Control Register
1
0
The SCON (serial port control) register contains control
and status information, and includes the ninth data bit
for transmit and receive (TB8/RB8 if required) mode
selection bits and serial port interrupt bits (TI and RI).
1
1
3
9-bit UART
Variable
Modes of Operation
The serial port on the VRS51x550/560 can operate in
four different modes. In all four modes, a transmission
is initiated by an instruction that uses the SBUF SFR
as a destination register. In Mode 0, reception is
initiated by setting RI to 0 and REN to 1. An incoming
start bit initiates reception in the other modes provided
that REN is set to 1. The following section describes
the four modes.
TABLE 17: SERIAL PORT CONTROL REGISTER (SCON) – SFR 98H
7
SM0
6
SM1
5
SM2
4
REN
3
TB8
2
RB8
1
TI
0
RI
Bit
Mnemonic Description
7
SM0
SM1
SM2
Bit to select mode of operation (see table
below)
Bit to select mode of operation (see table
below)
Multiprocessor communication is possible
in modes 2 and 3.
6
5
In modes 2 or 3 if SM2 is set to 1, RI will
not be activated if the received 9th data bit
(RB8) is 0.
In Mode 1, if SM2 = 1 then RI will not be
activated if a valid stop bit was not
received.
Serial Reception Enable Bit
This bit must be set by software and
cleared by software.
1: Serial reception enabled
0: Serial reception disabled
9th data bit transmitted in modes 2 and 3
This bit must be set by software and
cleared by software.
4
3
REN
TB8
______________________________________________________________________________________________
www.ramtron.com page 18 of 40
VRS51x550/560
Mode 0
The SEND signal enables the output of the shift
register to the alternate output function line of P3.0 and
enables SHIFT CLOCK to the alternate output function
line of P3.1. SHIFT CLOCK is high during T11, T12
and T1, T2 and T3, T4 of every machine cycle and low
during T5, T6, T7, T8, T9 and T10. At T12 of every
machine cycle in which SEND is active, the contents of
the transmit shift register are shifted to the right by one
position.
In this mode, the serial data exits and enters through
the RXD pin. TXD is used to output the shift clock. The
signal is composed of 8 data bits starting with the LSB.
The baud rate in this mode is 1/12 the oscillator
frequency.
Internal Bus
1
Zeros come in from the left as data bits shift out to the
right. The TX control block sends its final shift and
deactivates SEND while setting T1 after certain
conditions are fulfilled: The MSB of the data byte is at
the output position of the shift register; the 1 that was
initially loaded into the ninth position is just to the left of
the MSB; and all positions to the left of that contain
zeros. Once these conditions are met, the deactivation
of SEND and the setting of T1 occur at T1 of the tenth
machine cycle after the “write to SBUF” pulse.
Write to
SBUF
Q
S
D
SBUF
RXD P3.0
Shift
CLK
ZERO DETECTOR
Shift
Clock
TXD P3.1
Shift
Start
TX Control Unit
TX Clock
Send
Fosc/12
TI
Serial Port
Interrupt
RI
RX Clock
Receive
RX Control Unit
Reception in Mode 0
RI
REN
Start Shift
1
1
1
1
1
1
1
0
When REN and R1 are set to 1 and 0 respectively,
reception is initiated. The bits 11111110 are written to
the receive shift register at T12 of the next machine
cycle by the RX control unit. In the following phase, the
RX control unit will activate RECEIVE.
RXD P3.0
Input Function
RXD P3.0
Shift Register
READ SBUF
SBUF
Internal Bus
SHIFT CLOCK to the alternate output function line of
P3.1 is enabled by RECEIVE. At every machine cycle,
SHIFT CLOCK makes transitions at T5 and T11. The
contents of the receive shift register are shifted one
position to the left at T12 of every machine in which
RECEIVE is active. The value that comes in from the
right is the value that was sampled at the P3.0 pin at
T10 of the same machine cycle.
FIGURE 17: SERIAL PORT MODE 0 BLOCK DIAGRAM
Transmission in Mode 0
Any instruction that uses SBUF as a destination
register may initiate a transmission. The “write to
SBUF” signal also loads a 1 into the ninth position of
the transmit shift register and tells the TX control block
to begin a transmission. The internal timing is such that
one full machine cycle will elapse between a write to
SBUF instruction and the activation of SEND.
1’s are shifted out to the left as data bits are shifted in
from the right. The RX control block is flagged to do
one last shift and load SBUF when the 0 that was
initially loaded into the rightmost position arrives at the
leftmost position in the shift register.
______________________________________________________________________________________________
www.ramtron.com page 19 of 40
VRS51x550/560
Mode 1
When a transmission begins, it places the start bit at
TXD. Data transmission is activated one bit time later.
This activation enables the output bit of the transmit
shift register to TXD. One bit time after that, the first
shift pulse occurs.
For an operation in Mode 1, 10 bits are transmitted
through TXD or received through RXD. The
transactions are composed of: a Start bit (Low), 8 data
bits (LSB first) and one Stop bit (high). The reception is
completed once the Stop bit sets the RB8 flag in the
SCON register. Either Timer 1 or Timer 2 controls the
baud rate in this mode.
In this mode, zeros are clocked in from the left as data
bits are shifted out to the right. When the most
significant bit of the data byte is at the output position
of the shift register, the 1 that was initially loaded into
the ninth position is to the immediate left of the MSB,
and all positions to the left of that contain zeros. This
condition flags the TX control unit to shift one more
time.
The following diagram shows the serial port structure
when configured in Mode 1.
FIGURE 18: SERIAL PORT MODE 1 AND 3 BLOCK DIAGRAM
Internal Bus
1
Reception in Mode 1
Write to
SBUF
One to zero transitions at RXD initiate reception. It is
for this reason that RXD is sampled at a rate of 16
multiplied by the established baud rate. When a
transition is detected, 1FFh is written into the input shift
register and the divide-by-16 counter is immediately
reset. The divide-by-16 counter is reset in order to align
its rollovers with the boundaries of the incoming bit
times.
Timer 1
Overflow
Q
S
D
SBUF
TXD
CLK
Timer 2
Overflow
ZERO DETECTOR
÷2
0
1
Shift
Start
Data
SMOD
0
0
1
TX Control Unit
TCLK
TX Clock
÷16
Send
÷16
TI
1
RCLK
Serial Port
Interrupt
In total, there are 16 states in the counter. During the
7th, 8th and 9th counter states of each bit time; the bit
detector samples the value of RXD. The accepted
value is the value that was seen in at least two of the
three samples. The purpose of doing this is for noise
rejection. If the value accepted during the first bit time
is not zero, the receive circuits are reset and the unit
goes back to searching for another one to zero
transition. All false start bits are rejected by doing this.
If the start bit is valid, it is shifted into the input shift
register, and the reception of the rest of the frame will
proceed.
RX Clock
RI
Load
SBUF
RX Control Unit
1-0 Transition
Detector
Start
SHIFT
Bit
Detector
9-Bit Shift Register
Shift
RXD
LOAD SBUF
SBUF
READ SBUF
Internal Bus
For a receive operation, the data bits come in from the
right as 1’s shift out on the left. As soon as the start bit
arrives at the leftmost position in the shift register, (9-
bit register), it tells the RX control block to perform one
last shift operation: to set RI and to load SBUF and
RB8. The signal to load SBUF and RB8, and to set RI,
will be generated if, and only if, the following conditions
are met at the time the final shift pulse is generated:
Transmission in Mode 1
Transmission is initiated by any instruction that makes
use of SBUF as a destination register. The ninth bit
position of the transmit shift register is loaded by the
“write to SBUF” signal. This event also flags the TX
control unit that a transmission has been requested.
It is after the next rollover in the divide-by-16 counter
when transmission actually begins at T1 of the
machine cycle. It follows that the bit times are
synchronized to the divide-by-16 counter and not to the
“write to SBUF” signal.
·
·
Either SM2 = 0 or the received stop bit = 1
RI = 0
______________________________________________________________________________________________
www.ramtron.com page 20 of 40
VRS51x550/560
Mode 3
If both conditions are met, the stop bit goes into RB8,
the 8 data bits go into SBUF and RI is activated. If one
of these conditions is not met, the received frame is
lost. At this time, whether the above conditions are met
or not, the unit goes back to searching for a one to zero
transition in RXD.
In Mode 3, 11 bits are transmitted through TXD or
received through RXD. The transactions are
composed of: a Start bit (Low), 8 data bits (LSB first),
a programmable ninth data bit and one Stop bit (High).
Mode 3 is identical to Mode 2 in all respects but one;
the baud rate. Either Timer 1 or Timer 2 generates the
baud rate in Mode 3.
Mode 2
In Mode 2, a total of 11 bits are transmitted through
TXD or received through RXD. The transactions are
composed of: a Start bit (Low), 8 data bits (LSB first), a
programmable ninth data bit and one Stop bit (High).
FIGURE 20: SERIAL PORT MODE 3 BLOCK DIAGRAM
Internal Bus
1
Write to
SBUF
For transmission, the ninth data bit comes from the
TB8 bit of SCON. For example, the parity bit P in the
PSW could be moved into TB8.
Timer 1
Q
S
D
Overflow
SBUF
TXD
CLK
In the case of receive, the ninth data bit is
automatically written into RB8 of the SCON register.
Timer 2
Overflow
ZERO DETECTOR
÷2
0
1
Shift
Start
Data
SMOD
0
0
1
TX Control Unit
TCLK
In Mode 2, the baud rate is programmable to either
1/32 or 1/64 the oscillator frequency.
TX Clock
÷16
Send
÷16
TI
1
RCLK
Serial Port
Interrupt
FIGURE 19: SERIAL PORT MODE 2 BLOCK DIAGRAM
RI
SAMPLE
RX Clock
Start
Load
SBUF
RX Control Unit
1-0 Transition
Detector
SHIFT
Internal Bus
1
Write to
SBUF
Bit
Detector
9-Bit Shift Register
Shift
RXD
LOAD SBUF
Q
S
D
SBUF
Fosc/2
÷2
TXD
SBUF
CLK
READ SBUF
ZERO DETECTOR
Internal Bus
0
1
Shift
Data
Send
Stop
Start
SMOD
TX Control Unit
TX Clock
÷16
TI
÷16
Serial Port
Interrupt
Sample
RI
RX Clock
Control
Load
SBUF
RX Control Unit
1-0 Transition
Detector
Start
SHIFT
Bit
Detector
9-Bit Shift Register
Shift
RXD
LOAD SBUF
SBUF
READ SBUF
Internal Bus
______________________________________________________________________________________________
www.ramtron.com page 21 of 40
VRS51x550/560
Mode 2 and 3: Additional Information
Reception in Mode 2 and Mode 3
One to zero transitions at RXD initiate reception. It is
for this reason that RXD is sampled at a rate of 16
multiplied by the established baud rate. When a
transition is detected, the 1FFh is written into the input
shift register and the divide-by-16 counter is
immediately reset.
As mentioned earlier, for an operation in these modes,
11 bits are transmitted through TXD or received
through RXD. The signal comprises: a logical low Start
bit, 8 data bits (LSB first), a programmable ninth data
bit and one logical high Stop bit.
On transmission, the TB8 of the SCON register can be
assigned the value of 0 or 1. On receive, the ninth data
bit goes into RB8 in SCON. The baud rate is
programmable to either 1/32 or 1/64 the oscillator
frequency in Mode 2. Mode 3 may have a variable
baud rate generated from either Timer 1 or Timer 2
depending on the states of TCLK and RCLK.
During the 7th, 8th and 9th counter states of each bit
time; the bit detector samples the value of RXD. The
accepted value is the value that was seen in at least
two of the three samples. If the value accepted during
the first bit time is not zero, the receive circuits are
reset and the unit goes back to searching for another
one to zero transition. If the start bit is valid, it is shifted
into the input shift register and the reception of the rest
of the frame will proceed.
Transmission in Mode 2 and Mode 3
The transmission is initiated by any instruction that
makes use of SBUF as the destination register. The
ninth bit position of the transmit shift register is loaded
by the “write to SBUF” signal. This event also informs
the TX control unit that a transmission has been
requested. After the next rollover in the divide-by-16
counter, a transmission actually begins at T1 of the
machine cycle. The bit times are synchronized to the
divide-by-16 counter and not to the “write to SBUF”
signal, as in the previous mode.
For a receive operation, the data bits come in from the
right as 1’s shift out on the left. As soon as the Start bit
arrives at the leftmost position in the shift register (9-bit
register), it tells the RX control block to do one more
shift to set RI and load SBUF and RB8. The signal to
set RI and load SBUF and RB8 will be generated if,
and only if, the following conditions are satisfied at the
instance when the final shift pulse is generated:
·
·
Either SM2 = 0 or the received 9th bit is equal
to 1
RI = 0
Transmissions begin when the SEND signal is
activated, which places the Start bit at TXD. Data is
activated one bit time later. This activation enables the
output bit of the transmit shift register to TXD. The first
shift pulse occurs one bit time after that.
If both conditions are met, the ninth data bit received
goes into RB8, and the first 8 data bits go into SBUF. If
one of these conditions is not met, the received frame
is lost. One bit time later, whether the above conditions
are met or not, the unit goes back to searching for a
one to zero transition at the RXD input.
The first shift clocks a Stop bit (1) into the ninth bit
position of the shift register to TXD. Thereafter, only
zeros are clocked in. Thus, as data bits shift out to the
right, zeros are clocked in from the left. When TB8 is at
the output position of the shift register, the Stop bit is
just to the left of TB8, and all positions to the left of that
contain zeros. This condition signals to the TX control
unit to shift one more time and set TI, while
deactivating SEND. This occurs at the eleventh divide-
by-16 rollover after “write to SBUF”.
Please note that the value of the received Stop bit is
unrelated to SBUF, RB8 or RI.
______________________________________________________________________________________________
www.ramtron.com page 22 of 40
VRS51x550/560
The value to write into the TH1 register is defined by
the following formula:
UART Baud Rates Calculation
In Mode 0, the baud rate is fixed and is represented by
the following formula:
TH1 = 256 -
2SMODx Fosc
32 x 12x (Baud Rate)
Mode 0 Baud Rate = Oscillator Frequency
12
It is possible to use Timer 1 in 16-bit mode to generate
the baud rate for the serial port. To do this, leave the
Timer 1 interrupt enabled, configure the timer to run as
a 16-bit timer (high nibble of TMOD = 0001B) and use
the Timer 1 interrupt to perform a 16-bit software
reload. This can achieve very low baud rates.
In Mode 2, the baud rate depends on the value of the
SMOD bit in the PCON SFR. From the formula below,
we can see that if SMOD = 0 (which is the value on
reset), the baud rate is 1/32 the oscillator frequency.
Generating Baud Rates with Timer 2
Timer 2 is often preferred to generate the baud rate, as
it can be easily configured to operate as a 16-bit timer
with auto-reload. This enables much better resolution
than if using Timer 1 in 8-bit auto-reload mode.
Mode 2 Baud Rate = 2SMOD x (Oscillator Frequency)
64
The baud rate using Timer 2 is defined as:
The Timer 1 and/or Timer 2 overflow rate determines
the baud rates in modes 1 and 3.
Generating Baud Rates with Timer 1
Mode 1, 3 Baud Rate = Timer 2 Overflow Rate
16
When Timer 1 functions as a baud rate generator, the
baud rate in modes 1 and 3 are determined by the
Timer 1 overflow rate.
The timer can be configured as either a timer or a
counter in any of its three running modes. In typical
application, it is configured as a timer (C/T2 is set to 0).
Mode 1, 3 Baud Rate = 2SMODx Timer 1 Overflow Rate
32
To make the Timer 2 operate as a baud rate generator
the TCLK and RCLK bits of the T2CON register must
be set to 1.
Timer 1 must be configured as an 8-bit timer (TL1) with
auto-reload with TH1 value when an overflow occurs
(Mode 2). In this application, the Timer 1 interrupt
should be disabled.
The baud rate generator mode is similar to the auto-
reload mode in that an overflow in TH2 causes the
Timer 2 registers to be reloaded with the 16-bit value in
registers RCAP2H and RCAP2L, which are preset by
software. However, when Timer 2 is configured as a
baud rate generator, its clock source is Osc/2.
The two following formulas can be used to calculate
the baud rate and the reload value to be written into the
TH1 register.
Mode 1, 3 Baud Rate =
2SMODx Fosc
32 x 12(256 – TH1)
______________________________________________________________________________________________
www.ramtron.com page 23 of 40
VRS51x550/560
The following formula can be used to calculate the
baud rate in modes 1 and 3 using the Timer 2:
Modes 1, 3 Baud Rate =
Oscillator Frequency
32x[65536 – (RCAP2H, RCAP2L)]
The formula below is used to define the reload value to
write into the RCAP2h, RCAP2L registers to achieve a
given baud rate.
(RCAP2H, RCAP2L) = 65536 -
Fosc
32x[Baud Rate]
In the above formula, RCAP2H and RCAP2L are the
content of RCAP2H and RCAP2L taken as a 16-bit
unsigned integer.
Note that a rollover in TH2 does not set TF2, and will
not generate an interrupt. Because of this, the Timer 2
interrupt does not have to be disabled when Timer 2 is
configured in baud rate generator mode.
Also, if EXEN2 is set, a 1-to-0 transition in T2EX will
set EXF2 but will not cause a reload from RCAP2x to
Tx2. Therefore, when Timer 2 is used as a baud rate
generator, T2EX can be used as an extra external
interrupt.
Furthermore, when Timer 2 is running (TR2 is set to 1)
as a timer in baud rate generator mode, the user
should not try to read or write to TH2 or TL2. When
operating under these conditions, the timer is being
incremented every state time and the results of a read
or write command may be inaccurate.
The RCAP2 registers, however, may be read but
should not be written to, because a write may overlap a
reload operation and generate write and/or reload
errors. In this case, before accessing the Timer 2 or
RCAP2 registers, be sure to turn the timer off by
clearing TR2.
______________________________________________________________________________________________
www.ramtron.com
page 24 of 40
VRS51x550/560
Interrupt Vectors
Interrupts
The following table specifies each interrupt source, its
flag and its vector address.
The VRS51x550/560 devices have 8 interrupts (9 if we
include the WDT) and 7 interrupt vectors (including
reset) used for handling.
TABLE 20: INTERRUPT VECTOR CORRESPONDING FLAGS ANS VECTOR ADDRESS
Interrupt Source
Flag
Vector
Address
The interrupt can be enabled via the IE register shown
below:
RESET (+ WDT)
INT0
Timer 0
INT1
Timer 1
WDRESET
IE0
TF0
IE1
TF1
0000h
0003h
000Bh
0013h
001Bh
0023h
002Bh
TABLE 19: IEN0INTERRUPT ENABLE REGISTER –SFR A8H
7
EA
6
-
5
ET2
4
ES
3
ET1
2
EX1
1
ET0
0
EX0
Serial Port
Timer 2
RI+TI
TF2+EXF2
Bit
Mnemonic Description
7
EA
Disables All Interrupts
0: no interrupt acknowledgment
External Interrupts
1: Each interrupt source is individually
enabled or disabled by setting or clearing
its enable bit.
Reserved
The VRS51x550 and the VRS51x560 have two
external interrupt inputs named INT0 and INT1. These
interrupt lines are shared with P3.2 and P3.3.
6
5
4
3
2
1
0
-
Timer 2 Interrupt Enable Bit
ET2
ES
ET1
EX1
ET0
EX0
Serial Port Interrupt Enable Bit
Timer 1 Interrupt Enable Bit
External Interrupt 1 Enable Bit
Timer 0 Interrupt Enable Bit
External Interrupt 0 Enable Bit
The bits IT0 and IT1 of the TCON register determine
whether the external interrupts are level or edge
sensitive.
If ITx = 1, the interrupt will be raised when a 1 to 0
transition occurs at the interrupt pin. For the interrupt to
be noticed by the processor, the duration of the sum
high and low condition must be at least equal to 12
oscillator cycles.
The following figure illustrates the various interrupt
sources on the VRS51x550/560.
FIGURE 21: INTERRUPT SOURCES
If ITx = 0, the interrupt will occur when a logic low
condition is present on the interrupt pin.
INT0
TF0
IT0
IE0
The state of the external interrupt, when enabled, can
be monitored using the flags, IE0 and IE1 of the TCON
register that are set when the interrupt condition
occurs.
In the case where the interrupt was configured as edge
sensitive, the associated flag is automatically cleared
when the interrupt is serviced. If the interrupt is
configured as level sensitive, then the interrupt flag
must be cleared by the software.
INTERRUPT
SOURCES
INT1
TF1
IT1
IE1
T1
RI
TF2
EXF2
______________________________________________________________________________________________
www.ramtron.com page 25 of 40
VRS51x550/560
Timer 0 and Timer 1 Interrupt
Execution of an Interrupt
Both Timer 0 and Timer 1 can be configured to
When the processor receives an interrupt request, an
automatic jump to the desired subroutine occurs. This
jump is similar to executing a branch to a subroutine
instruction: the processor automatically saves the
address of the next instruction on the stack. An internal
flag is set to indicate that an interrupt is taking place,
and then the jump instruction is executed. An interrupt
subroutine must always end with the RETI instruction.
This instruction allows users to retrieve the return
address placed on the stack.
generate an interrupt when
a
rollover of the
timer/counter occurs (except Timer 0 in Mode 3).
The TF0 and TF1 flags serve to monitor timer overflow
occurring from Timer 0 and Timer 1. These interrupt
flags are automatically cleared when the interrupt is
serviced.
Timer 2 Interrupt
The RETI instruction also allows updating of the
internal flag, which will take into account an interrupt
with the same priority.
A Timer 2 interrupt can occur if TF2 and/or EXF2 flags
are set to 1 and if the Timer 2 interrupt is enabled.
The TF2 flag is set when a rollover of the Timer 2
Counter/Timer occurs. The EXF2 flag can be set by a 1
to 0 transition on the T2EX pin by the software.
Interrupt Enable and Interrupt Priority
When the VRS51x550/560 are initialized, all interrupt
sources are inhibited by the bits of the IE register being
reset to 0. It is necessary to start by enabling the
interrupt sources that the application requires. This is
achieved by setting bits in the IE register, as discussed
previously.
Note that neither flag is cleared by the hardware upon
execution of the interrupt service routine. The service
routine may have to determine whether it was TF2 or
EXF2 that generated the interrupt. These flag bits will
have to be cleared by the software.
Every bit that generates interrupts can either be
cleared or set by the software, yielding the same result
as when the operation is done by the hardware. In
other words, pending interrupts can be cancelled and
interrupts can be generated by the software.
This register is part of the bit addressable internal
RAM. For this reason, each bit can be modified
individually with one instruction without having to
modify the other bits of the register. All interrupts can
be inhibited by setting EA to 0.
The order in which interrupts are serviced is shown in
the following table:
Serial Port Interrupt
The serial port can generate an interrupt upon byte
reception or once the byte transmission is complete.
TABLE 21: INTERRUPT NATURAL PRIORITY
Interrupt Source
RESET + WDT (Highest Priority)
IE0
TF0
IE1
Those two conditions share the same interrupt vector
and it is up to the user-developed interrupt service
routine software to ascertain the cause of the interrupt
by examining the serial interrupt flags RI and TI.
TF1
Note that neither of these flags is cleared by the
hardware upon execution of the interrupt service
routine. The software must clear these flags.
RI+TI
TF2+EXF2 (Lowest Priority)
______________________________________________________________________________________________
www.ramtron.com page 26 of 40
VRS51x550/560
The WDT timeout delay can be adjusted by configuring
the clock divider input for the time base source clock of
the WDT. To select the divider value, bit2-bit0
(WDPS2~WDPS0) of the WDTCON should be set
accordingly.
Modifying the Interrupt Order of Priority
The VRS51x550 and VRS51x560 devices allow users
to modify the natural priority of the interrupts. One may
modify the order by programming the bits in the IP
(Interrupt Priority) register. When any bit in this register
is set to 1, it gives the corresponding source a greater
priority than interrupts coming from sources that don’t
have their corresponding IP bit set to 1.
Clearing the WDT is accomplished by setting the CLR
bit of the WDTCON to 1. This action will clear the
contents of the 16-bit counter and force it to restart.
The IP register is represented in the table below:
Watchdog Timer Registers
TABLE 22: IP INTERRUPT PRIORITY REGISTER –SFR B8H
Three registers of the VRS51x550/560 devices are
associated with the watchdog timer: WDTCON, the
WDTLOCK and the SYSCON registers. The WDTCON
register allows the user to enable the WDT, to clear the
counter and to divide the clock source. The WDRESET
bit of the SYSCON register indicates whether the
watchdog timer has caused the device reset.
7
EA
6
-
5
ET2
4
ES
3
ET1
2
EX1
1
ET0
0
EX0
Bit
Mnemonic Description
7
6
-
-
Gives Timer 2 Interrupt Higher Priority
5
4
3
2
1
0
PT2
PS
PT1
PX1
PT0
PX0
Gives Serial Port Interrupt Higher Priority
Gives Timer 1 Interrupt Higher Priority
Gives INT1 Interrupt Higher Priority
Gives Timer 0 Interrupt Higher Priority
Gives INT0 Interrupt Higher Priority
TABLE 23: WATCHDOG TIMER REGISTERS: WDTCON – SFR 9FH
7
6
5
4
3
2
1
0
WDCLR
WDTE
Unused
Unused
WDTPS [2:0]
Bit
7
Mnemonic
WDTE
Description
Watchdog Timer Enable Bit
6
5
[4:3]
2
1
Unused
WDCLR
Unused
-
Watchdog Timer
Watchdog Timer Counter Clear Bit
-
The watchdog timer (WDT) is a 16-bit free-running
counter that generates a reset signal if the counter
overflows. The WDT is useful for systems that are
susceptible to noise, power glitches and other
conditions that can cause the software to go into
infinite dead loops or runaways. The WDT function
gives the user software a recovery mechanism from
abnormal software conditions.
WDPS [2:0]
Watchdog Timer Clock Source Divider
0
The watchdog timer on the VRS51x550/560 is driven
by the oscillator.
To enable the WDT, the user must set bit 7 (WDTE) of
the Watchdog Timer Control Register (WDTCON) to 1.
Once WDTE has been set to 1, the 16-bit counter will
start to count with the selected time base source clock
configured in WDPS2~WDPS0. The watchdog timer
will generate a reset signal if an overflow has taken
place.
The WDTE bit will be cleared to 0 automatically when
the device is reset by either the hardware or a WDT
reset.
Once the WDT is enabled, the user software must
clear it periodically. In the case where the WDT is not
cleared, its overflow will trigger a reset of the device.
The user should check the WDRESET bit of the
SYSCON register whenever an unpredicted reset has
taken place.
______________________________________________________________________________________________
www.ramtron.com page 27 of 40
VRS51x550/560
The table below shows examples of watchdog timeout
periods that the user will obtain for different values of
the WDPSx bits of the watchdog timer register.
Crystal Consideration
The crystal connected to the VRS51x550/560 oscillator
input should be of a parallel type, operating in
fundamental mode.
TABLE 24: WATCH DOG TIMER PERIOD VS. WDWDPS [2:0] BIT
Fosc Division
Factor
WDT
Timeout
(ms) @
20MHz
The following table shows the value of the capacitors
and feedback resistor that must be used at different
operating frequencies.
WDPS [2:0]
000
001
010
011
100
101
110
111
8
16
26.2
52.4
XTAL
C1
C2
R
XTAL
C1
3MHz
30 pF
30 pF
open
33MHz
5 pF
6MHz
30 pF
30 pF
open
40MHz
2 pF
12MHz
30 pF
30 pF
open
16MHz 25MHz
30 pF
30 pF
open
15 pF
15 pF
62KO
32
104.8
209.7
419.4
838.8
1677.7
3355.4
64
128
256
512
1024
C2
5 pF
2 pF
R
6.8K
4.7K
Note: Oscillator circuits may differ with different
crystals or ceramic resonators in higher oscillation
frequency.
The System Control Register
The system control register is used to monitor the
status of the watchdog timer and inhibit the address
Latch Enable signal output.
Crystals or ceramic resonator characteristics vary from
one manufacturer to the other. The user should review
the technical literature provided with any crystal or
ceramic resonators or contact the manufacturer to
select the appropriate values for external components.
TABLE 25: THE SYSTEM CONTROL REGISTER (SYSCON)–SFR BFH
7
6
5
4
3
2
1
0
ALEI
WDRESET
Unused
XRAME
Bit
7
[6:3]
2
1
0
Mnemonic
WDRESET
Unused
Unused
Unused
ALEI
Description
Watchdog Timer Reset Status Bit
-
-
-
XTAL1
1: Enable Electromagnetic Interference
Reducer
XTAL
VRS51x550
0: Disable Electromagnetic Interference
Reducer
VRS51x560
The WDRESET bit of the SYSCON register is the
watchdog timer reset bit. It will be set to 1 when a reset
signal is generated by the WDT overflow. The user
should check the WDRESET bit state if a reset has
taken place in applications where the watchdog timer is
activated.
R
XTAL2
C1
C2
Reduced EMI Function
The VRS51x550 and VRS51x560 devices can also be
set up to reduce EMI (electromagnetic interference) by
setting bit 0 (ALEI) of the SYSCON register to 1. This
function will inhibit the Fosc/6Hz clock signal output to
the ALE pin.
______________________________________________________________________________________________
www.ramtron.com page 28 of 40
VRS51x550/560
Operating Conditions
TABLE 26: OPERATING CONDITIONS
Symbol
TA
TS
VCC5V
VCC3V
Fosc 25
Description
Min.
-40
-55
4.5
3.0
3.0
Typ.
25
25
5.0
3.3
-
Max.
85
155
5.5
3.6
40
Unit
ºC
ºC
V
V
Remarks
Ambient temperature operating
Operating temperature
Storage temperature
Supply voltage
Supply voltage
Oscillator Frequency
5 Volt device
3.3 Volt device
For 5V & 3.3V application
MHz
DC Characteristics
TABLE 27: DC CHARACTERISTICS
AMBIENT TEMPERATURE = -40°C TO 85°C, 3.0V TO 5.5V
Symbol Parameter
Valid
Port 0,1,2,3,4,#EA
RES, XTAL1
Port 0,1,2,3,4,#EA
RES, XTAL1
Port 0, ALE, #PSEN
Port 1,2,3,4
Min.
-0.5
0
Max.
0.8
0.8
Unit
V
V
V
V
Test Conditions
VIL1
Input Low Voltage
Input Low Voltage
Input High Voltage
Input High Voltage
Output Low Voltage
Output Low Voltage
VIL2
VIH1
VI H2
VOL1
VOL2
2.0
VCC+0.5
70% VCC VCC+0.5
0.45
0.45
V
V
IOL=3.2mA
IOL=1.6mA
2.4
V
IOH=-800uA (Vcc = 5V)
VOH1
Output High Voltage
Port 0
90% VCC
2.4
V
V
V
IOH=-80uA
IOH=-60uA (Vcc = 5V)
IOH=-10uA
Port
1,2,3,4,ALE,#PSEN
VOH2
IIL
Output High Voltage
90% VCC
Logical 0 Input Current
Port 1,2,3,4
-75
uA
Vin=0.45V
Logical Transition
Current
Port 1,2,3,4
Port 0, #EA
RES
-650
+10
uA
Vin=2.OV
ITL
ILI
Input Leakage Current
uA
0.45V<Vin<VCC
R RES Reset Pull-Down
Resistance
50
300
10
Kohm
C-10
Pin Capacitance
pF
Freq=1 MHz, Ta=25°C
15
10
mA
mA
Active mode 25MHz
Active mode 16MHz
ICC
Power Supply Current
VDD
7.5
6
150
mA
mA
uA
Idle mode 25MHz
Idle mode, 16MHz
Power down mode
FIGURE 22: ICC IDLE MODE TEST CIRCUIT
FIGURE 23: ICC ACTIVE MODE TEST CIRCUIT
Vcc
Vcc
Vcc
Icc
Icc
VCC
VCC
8
RST
8
PO
EA
PO
EA
RST
VRS51x550
VRS51x560
XTAL2
VRS51x550
VRS51x560
XTAL2
XTAL1
VSS
(NC)
(NC)
Clock Signal
XTAL1
VSS
Clock Signal
______________________________________________________________________________________________
www.ramtron.com page 29 of 40
VRS51x550/560
AC Characteristics
TABLE 28: AC CHARACTERISTICS
Fosc 16
Variable Fosc
Valid
Symbol
T LHLL
T AVLL
T LLAX
T LLIV
T LLPL
T PLPH
T PLIV
Parameter
ALE Pulse Width
Cycle
Unit
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
Min.
Type Max.
Min.
Type
Max.
RD/WRT 115
RD/WRT 43
RD/WRT 53
RD
2xT - 10
T - 20
T - 10
Address Valid to ALE Low
Address Hold after ALE Low
ALE Low to Valid Instruction In
ALE Low to #PSEN low
#PSEN Pulse Width
#PSEN Low to Valid Instruction In
Instruction Hold after #PSEN
Instruction Float after #PSEN
Address to Valid Instruction In
#PSEN Low to Address Float
#RD Pulse Width
240
177
4xT - 10
3xT -10
RD
RD
RD
RD
RD
RD
RD
RD
WRT
RD
RD
RD
RD
RD
RD/WRT 178
RD/WRT 230
WRT
WRT
WRT
RD
53
173
T - 10
3xT - 15
T PXIX
T PXIZ
0
0
87
292
10
T + 25
5xT - 20
10
T AVI V
T PLAZ
T RLRH
T WLWH
T RLDV
T RHDX
T RHDZ
T LLDV
T AVDV
T LLYL
T AVYL
T QVWH
T QVWX
T WHQX
T RLAZ
T YALH
T CHCL
T CLCX
T CLCH
T CHCX
365
365
6xT - 10
6xT - 10
#WR Pulse Width
#RD Low to Valid Data In
Data Hold after #RD
302
5xT - 10
0
0
Data Float after #RD
145
590
542
197
2xT + 20
8xT - 10
9xT - 20
3xT + 10
ALE Low to Valid Data In
Address to Valid Data In
ALE low to #WR High or #RD Low
Address Valid to #WR or #RD Low
Data Valid to #WR High
Data Valid to #WR Transition
Data Hold after #WR
#RD Low to Address Float
#W R or #RD High to ALE High
Clock Fall Time
3xT - 10
4xT - 20
7xT - 35
T - 25
403
38
73
T + 10
5
RD/WRT 53
72
T -10
T+10
Clock Low Time
Clock Rise Time
Clock High Time
T,TCLCL Clock Period
63
1/fosc
______________________________________________________________________________________________
www.ramtron.com page 30 of 40
VRS51x550/560
Data Memory Read Cycle Timing
The following timing diagram shows what occurs at each signal during a Data Memory Read Cycle.
FIGURE 24: DATA MEMORY READ CYCLE TIMING
T12
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10 T11 T12
T1
T2
T3
OSC
ALE
1
2
#PSEN
#RD
5
7
3
ADDRESS A15-A8
PORT2
PORT0
3
4
6
8
INST in
Float
A7-A0
Float
Data in
Float
ADDRESS or
Float
______________________________________________________________________________________________
www.ramtron.com page 31 of 40
VRS51x550/560
Program Memory Read Cycle Timing
The following timing diagram shows what occurs at each signal during a Program Memory Read Cycle.
FIGURE 25: PROGRAM MEMORY READ CYCLE
T12
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10 T11 T12
T1
T2
T3
OSC
ALE
1
2
5
7
#PSEN
#RD,#WR
PORT2
PORT0
3
ADDRESS A15-A8
ADDRESS A15-A8
3
4
6
8
Float
A7-A0 Float
INST in Float
A7-A0 Float
INST in Float
______________________________________________________________________________________________
www.ramtron.com page 32 of 40
VRS51x550/560
Data Memory Write Cycle Timing
The following timing diagram shows what occurs at each signal during a Data Memory Write Cycle.
FIGURE 26: DATA MEMORY WRITE CYCLE TIMING
T12
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10 T11 T12
T1
T2
T3
OSC
ALE
1
#PSEN
#WR
5
6
2
ADDRESS A15-A8
3
PORT2
PORT0
2
4
INST in
Float
A7-A0
Data out
ADDRESS or
Float
______________________________________________________________________________________________
www.ramtron.com page 33 of 40
VRS51x550/560
I/O Port Timing
The following timing diagram shows what occurs during I/O Port Timing.
FIGURE 27: I/O PORTS TIMING
T7
T8
T9
T10 T11 T12
T1
T2
T3
T4
T5
T6
T7
T8
X1
Sampled
Inputs P0,P1
Sampled
Inputs P2,P3
Output by Mov
Px, Src
Current Data
Next Data
Sampled
RxD at Serial
Port Shift
Clock Mode 0
______________________________________________________________________________________________
www.ramtron.com page 34 of 40
VRS51x550/560
External Clock Timing
FIGURE 28: TIMING REQUIREMENT OF EXTERNAL CLOCK (VSS= 0.0V IS ASSUMED)
TCLCL
Vdd - 0.5V
70% Vdd
20% Vdd-0.1V
0.45V
TCLCX
TCHCX
TCHCL
TCLCH
External Program Memory Read Cycle
The following timing diagram shows what occurs at each signal during an External Program Memory Read Cycle.
FIGURE 29: EXTERNAL PROGRAM MEMORY READ CYCLE
TPLPH
#PSEN
TLLPL
TLHLL
ALE
TPXIZ
TAVLL TLLAX
A0-A7
TPLIV
TPXIX
TPLAZ
TAVIV
Instruction IN
A0-A7
PORT 0
PORT2
P2.0-P2.7 or AB-A15 from DPH
A8-A15
______________________________________________________________________________________________
www.ramtron.com page 35 of 40
VRS51x550/560
External Data Memory Read Cycle
The following timing diagram shows what occurs at each signal during an External Data Memory Read Cycle.
FIGURE 30: EXTERNAL DATA MEMORY READ CYCLE
#PSEN
TYHLH
ALE
TLLDV
TRLRH
TLLYL
#RD
TRLDV
TRHDZ
TRHDX
DATA IN
TAVLL
TLLAX
A0-A7
TRLAZ
A0-A7
From PCL
INSTRL
IN
PORT 0
PORT 2
From Ri or DPL
TAVYL
TAVDV
P2.0-P2.7 or A8 -A15 from DPH
A8-A15 from PCH
______________________________________________________________________________________________
www.ramtron.com page 36 of 40
VRS51x550/560
External Data Memory Write Cycle
The following timing diagram shows what occurs at each signal during an External Data Memory Write Cycle.
FIGURE 31: EXTERNAL DATA MEMORY WRITE CYCLE
#PSEN
TYHLH
ALE
TLHLL
TLLYL
TWLWH
#WR
TAVLL
TQVWX
TWHQX
TLLAX
TQVWH
A0-A7
From PCL
A0-A7
From Ri or DPL
INSTRL
IN
DATA OUT
PORT 0
PORT 2
TAVYL
P2.0-P2.7 or A8-A15 from DPH
A8-A15 from PCH
.
______________________________________________________________________________________________
www.ramtron.com page 37 of 40
VRS51x550/560
Plastic Chip Carrier (PLCC-44)
L
VRS51x550
VRS51x560
PLCC-44
GE
E
HE
Y
A2
A1
A
D
TABLE 29: DIMENSIONS OF PLCC-44 CHIP CARRIER
HD
Dimension in inch
Symbol
Dimension in mm
Minimal/Maximal
-/4.70
Minimal/Maximal
A
-/0.185
Al
A2
bl
b
C
D
E
e
GD
GE
HD
HE
L
0.020/-
0.51/
0.145/0.155
0.026/0.032
0.016/0.022
0.008/0.014
0.648/0.658
0.648/0.658
0.050 BSC
0.590/0.630
0.590/0.630
0.680/0.700
0.680/0.700
0.090/0.110
-/0.004
3.68/3.94
0.66/0.81
0.41/0.56
0.20/0.36
16.46/16.71
16.46/16.71
1.27 BSC
14.99/16.00
14.99/16.00
17.27/17.78
17.27/17.78
2.29/2.79
-/0.10
C
e
b
b1
GD
Note:
?
1. Dimensions D & E do not include interlead Flash.
2. Dimension B1 does not include dambar
protrusion/intrusion.
?y
/
/
3. Controlling dimension: Inch
4. General appearance spec should be based on
final visual inspection spec.
______________________________________________________________________________________________
www.ramtron.com page 38 of 40
VRS51x550/560
C
Quad Flat Package (QFP-44)
L
L1
S
S
VRS51x550
VRS51x560
QFP-44
b
D2 D1 D
2
A2
R1
A1
Gage Plane
0.25mm
A
3
R2
E2
E1
E
TABLE 30: DIMENSIONS OF QFP-44 CHIP CARRIER
Dimension in in.
Symbol
Dimension in mm
Minimal/Maximal
-/2.55
Minimal/Maximal
A
-/0.100
Al
A2
b
c
D
D1
D2
E
E1
E2
e
0.006/0.014
0.071 / 0.087
0.012/0.018
0.004 / 0.009
0.520 BSC
0.394 BSC
0.315
0.520 BSC
0.394 BSC
0.315
0.031 BSC
0.029 / 0.041
0.063
0.005/-
0.005/0.012
0.008/-
0.15/0.35
1.80/2.20
0.30/0.45
0.09/0.20
13.20 BSC
10.00 BSC
8.00
13.20 BSC
10.00 BSC
8.00
0.80 BSC
0.73/1.03
1.60
0.13/-
0.13/0.30
0.20/-
e1
C
Seating Plane
e
L
L1
R1
R2
S
Note:
1. Dimensions D1 and E1 do not include mold
protrusion.
0
0°/7°
0°/ -
10° REF
7° REF
0.004
as left
as left
as left
as left
2. Allowance protrusion is 0.25mm per side.
3. Dimensions D1 and E1 do not include mold
mismatch and are determined datum plane.
4. Dimension b does not include dambar
protrusion.
? 1
? 2
? 3
?C
0.10
5. Allowance dambar protrusion shall be 0.08 mm
total in excess of the b dimension at maximum
material condition. Dambar cannot be located
on the lower radius of the lead foot.
______________________________________________________________________________________________
www.ramtron.com page 39 of 40
VRS51x550/560
Ordering Information
Device Number Structure
VRS51x550 Ordering Options
Device Number
Flash Size
RAM Size
Package
Voltage
Temperature
Frequency
Option
PLCC-44
PLCC-44
QFP-44
QFP-44
DIP-40
VRS51C550-40-L
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
8KB
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
4.5V to 5.5V
3.0V to 3.6V
4.5V to 5.5V
3.0V to 3.6V
4.5V to 5.5V
3.0V to 3.6V
4.5V to 5.5V
3.0V to 3.6V
4.5V to 5.5V
3.0V to 3.6V
4.5V to 5.5V
3.0V to 3.6V
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
40MHz
25MHz
40MHz
25MHz
40MHz
25MHz
40MHz
25MHz
40MHz
25MHz
40MHz
25MHz
VRS51L550-25-L
VRS51C550-40-Q
VRS51L550-25-Q
VRS51C550-40-P
VRS51L550-25-P
VRS51C550-40-LG
VRS51L550-25-LG
VRS51C550-40-QG
VRS51L550-25-QG
VRS51C550-40-PG
VRS51L550-25-PG
DIP-40
PLCC-44
PLCC-44
QFP-44
QFP-44
DIP-40
DIP-40
VRS51x560 Ordering Options
Device Number
Flash Size
RAM Size
Package
Voltage
Temperature
Frequency
Option
PLCC-44
QFP-44
DIP-40
PLCC-44
QFP-44
DIP-40
VRS51C560-40-L
VRS51C560-40-Q
VRS51C560-40-P
VRS51C560-40-LG
VRS51C560-40-QG
VRS51C560-40-PG
16KB
16KB
16KB
16KB
16KB
16KB
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
256 Bytes
4.5V to 5.5V
4.5V to 5.5V
4.5V to 5.5V
4.5V to 5.5V
4.5V to 5.5V
4.5V to 5.5V
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
40MHz
40MHz
40MHz
40MHz
40MHz
40MHz
Disclaimers
Right to make change - Ramtron reserves the right to make changes to its products - including circuitry, software and services - without notice at
any time. Customers should obtain the most current and relevant information before placing orders.
Use in applications - Ramtron assumes no responsibility or liability for the use of any of its products, and conveys no license or title under any
patent, copyright or mask work right to these products and makes no representations or warranties that these products are free from patent,
copyright or mask work right infringement unless otherwise specified. Customers are responsible for product design and applications using Ramtron
parts. Ramtron assumes no liability for applications assistance or customer product design.
Life support – Ramtron products are not designed for use in life support systems or devices. Ramtron customers using or selling Ramtron products
for use in such applications do so at their own risk and agree to fully indemnify Ramtron for any damages resulting from such applications.
______________________________________________________________________________________________
www.ramtron.com
page 40 of 40
相关型号:
©2020 ICPDF网 联系我们和版权申明