X11SSM [ETC]
X11SSM(-F)/X11SSL(-F) User Manual;
| 型号： | X11SSM |
| 厂家： | 
ETC |
| 描述： | X11SSM(-F)/X11SSL(-F) User Manual |
| 文件： | 总124页 (文件大小：5813K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
X11SSM(-F)
X11SSL(-F)
USER MANUAL
Revision 1.1a
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes
no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update
or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:
For the most up-to-date version of this manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual
at any time and without notice. This product, including software and documentation, is the property of Supermicro and/
or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except
as expressly permitted by the terms of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIALDAMAGESARISING FROM THE USE OR INABILITYTO USE THIS PRODUCT
OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER
MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the
State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution
of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,
may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only
to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,
nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical
systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products
for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully
indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Manual Revision 1.1a
Release Date: September 04, 2018
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this
document. Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2018 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
Preface
About This Manual
This manual is written for system integrators, IT technicians and knowledgeable end users. It
provides information for the installation and use of the X11SSM(-F)/X11SSL(-F) motherboard.
About This Motherboard
The Super X11SSM(-F)/X11SSL(-F) motherboard supports an Intel Xeon E3-1200 v6/v5,
7th/6th Gen Core i3, Pentium, and Celeron series processor in an LGA 1151 (H4) socket. With
support of the Intel C236/232 chipset*, DDR4 memory, SATA 3.0, Intel Node Manager**, and
Trusted Platform Module (TPM), this motherboard is optimized for cost-effective, entry-level
server platforms. Please note that this motherboard is intended to be installed and serviced
by professional technicians only. For processor/memory updates, please refer to our website
at http://www.supermicro.com/products/.
* The X11SSM(-F) supports the Intel C236 chip, and the X11SSL(-F), the C232 chip.
** Intel Node Manager is supported by the X11SSM-F only.
Conventions Used in the Manual
Special attention should be given to the following symbols for proper installation and to prevent
damage done to the components or injury to yourself:
Warning! Indicates important information given to prevent equipment/property damage
or personal injury.
Warning! Indicates high voltage may be encountered when performing a procedure.
Important: Important information given to ensure proper system installation or to
relay safety precautions.
Note: Additional Information given to differentiate various models or provides infor-
mation for correct system setup.
3
X11SSM(-F)/X11SSL(-F) User Manual
Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
Tel:
Fax:
Email:
+1 (408) 503-8008
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
www.supermicro.com
Website:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
www.supermicro.nl
Website:
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
Website:
support@supermicro.com.tw
www.supermicro.com.tw
4
Preface
Table of Contents
Chapter 1 Introduction
1.1 Checklist...............................................................................................................................8
Quick Reference ...............................................................................................................12
Quick Reference Table......................................................................................................13
Motherboard Features.......................................................................................................15
1.2 Processor and Chipset Overview.......................................................................................19
1.3 Special Features ................................................................................................................19
Recovery from AC Power Loss.........................................................................................19
1.4 System Health Monitoring..................................................................................................20
Onboard Voltage Monitors ................................................................................................20
Fan Status Monitor with Firmware Control .......................................................................20
Environmental Temperature Control .................................................................................20
System Resource Alert......................................................................................................20
1.5 ACPI Features....................................................................................................................20
1.6 Power Supply .....................................................................................................................21
1.7 Serial Port...........................................................................................................................21
Chapter 2 Installation
2.1 Static-Sensitive Devices.....................................................................................................22
Precautions .......................................................................................................................22
Unpacking .........................................................................................................................22
2.2 Motherboard Installation.....................................................................................................23
Tools Needed ....................................................................................................................23
Location of Mounting Holes ..............................................................................................23
Installing the Motherboard.................................................................................................24
2.3 Processor and Heatsink Installation...................................................................................25
Installing the LGA1151 Processor.....................................................................................25
Installing an Active CPU Heatsink with Fan .....................................................................28
Removing the Active Heatsink ..........................................................................................30
Installing a Passive CPU Heatsink ...................................................................................31
Removing the Passive Heatsink .......................................................................................32
5
X11SSM(-F)/X11SSL(-F) User Manual
2.4 Memory Support and Installation .......................................................................................33
Memory Support................................................................................................................33
DIMM Module Population Configuration ...........................................................................33
DIMM Module Population Sequence ................................................................................34
DIMM Installation ..............................................................................................................35
DIMM Removal .................................................................................................................35
2.5 Rear I/O Ports ....................................................................................................................36
2.6 Front Control Panel............................................................................................................41
2.7 Connectors .........................................................................................................................46
Power Connections...........................................................................................................46
Headers.............................................................................................................................48
2.8 Jumper Settings .................................................................................................................57
How Jumpers Work...........................................................................................................57
2.9 LED Indicators....................................................................................................................62
Chapter 3 Troubleshooting
3.1 Troubleshooting Procedures ..............................................................................................65
Before Power On ..............................................................................................................65
No Power ..........................................................................................................................65
No Video ...........................................................................................................................65
System Boot Failure .......................................................................................................66
Memory Errors ..................................................................................................................66
Losing the System's Setup Configuration.........................................................................67
When the System Becomes Unstable ..............................................................................67
3.2 Technical Support Procedures ...........................................................................................69
3.3 Frequently Asked Questions ..............................................................................................70
3.4 Battery Removal and Installation .......................................................................................71
Battery Removal................................................................................................................71
Proper Battery Disposal....................................................................................................71
Battery Installation.............................................................................................................71
Chapter 4 BIOS
4.1 Introduction.........................................................................................................................73
Starting the Setup Utility ...................................................................................................73
4.2 Main Setup .........................................................................................................................74
6
4.3 Advanced Setup Configurations.........................................................................................76
4.4 Event Logs .......................................................................................................................101
4.5 IPMI ..................................................................................................................................103
4.6 Security.............................................................................................................................106
4.7 Boot ..................................................................................................................................109
4.8 Save & Exit.......................................................................................................................111
Appendix A BIOS Codes
Appendix B Software Installation
B.1 Installing Software Programs ...........................................................................................114
B.2 SuperDoctor® 5.................................................................................................................115
Appendix C Standardized Warning Statements
Battery Handling..............................................................................................................116
Product Disposal.............................................................................................................118
Appendix D UEFI BIOS Recovery
Appendix E Dual Boot Block
BIOS Boot Block .............................................................................................................123
BIOS Boot Block Corruption Occurrence ......................................................................123
7
X11SSM(-F)/X11SSL(-F) User Manual
Chapter 1
Introduction
Congratulations on purchasing your computer motherboard from an industry leader. Supermicro
boards are designed to provide you with the highest standards in quality and performance.
Several important parts that are included with the motherboard are listed below. If anything
listed is damaged or missing, please contact your retailer.
1.1 Checklist
Main Parts List
Description
Part Number
Quantity
Supermicro Motherboard
SATA Cables
X11SSM(-F)/X11SSL(-F)
CBL-0044L
1
6
I/O Shield
MCP-260-00042-0N
MNL-1785-QRG
1
1
Quick Reference Guide
Important Links
For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: https://www.supermicro.com/wftp/driver/
• Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm
• If you have any questions, please contact our support team at: support@supermicro.com
This manual may be periodically updated without notice. Please check the Supermicro website
for possible updates to the manual revision level.
8
Chapter 1: Introduction
Figure 1-1. X11SSM(-F) Motherboard Image
Note: All graphics shown in this manual were based upon the latest PCB revision
available at the time of publication of the manual. The motherboard you received may
or may not look exactly the same as the graphics shown in this manual.
9
X11SSM(-F)/X11SSL(-F) User Manual
Figure 1-2. X11SSL(-F) Motherboard Image
10
Chapter 1: Introduction
Figure 1-3. X11SSM(-F)/X11SSL(-F) Motherboard Layout
(not drawn to scale)
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA
FAN3
Differences between X11SSM(-F)/X11SSL(-F)
X11SSM(-F)
X11SSL(-F)
COM2
Yes
No
IPMI LAN
Yes: X11SSM-F
Yes: X11SSL-F
I-SATA6 & I-SATA7
PCI-E Slot 4
Yes
Yes
No
No
Note: Components not documented are for internal testing only.
11
X11SSM(-F)/X11SSL(-F) User Manual
Quick Reference
IPMI_LAN
USB0/1
JUIDB1
LAN1
COM1
VGA
LAN2
LE1
USB6/7
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
JOH1
FAN4
COM2
LEDBMC
LED BMC
BMC
IPMI_LAN
JIPMB1
JPL2
JPL1
JPG1
JPL2
JPL1
JBR1
JPB1
JI2C1
MAC CODE
JPME2
JI2C2
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
JPI2C1
JPWR2
JD1
SP1
SP1
CPU
BT1
USB2/3
JL1
USB2/3
JL1
JBT1JBT1 BT1
Intel PCH
JTPM1
USB4/5
JWD1
JSTBY1
I-SATA7
JSD1
I-SGPIO1
USB10
I-SATA7
I-SATA6
I-SATA5
I-SATA4
I-SATA3
I-SATA2
JPWR1
JF1
USB10(3.0)
LED PWR
LEDPWR
FAN2
FAN1
I-SATA2
FANA FAN3
JF1
FAN3
FANA
I-SGPIO2
JSD2
I-SATA1
USB8/9
FAN2 FAN1
I-SATA0
Notes:
• See Chapter 2 for detailed information on jumpers, I/O ports, and JF1 front panel con-
nections.
• " " indicates the location of Pin 1.
• Jumpers/LED indicators not indicated are used for testing only.
• Please refer to the table on page 10 to see model variations.
• When LEDPWR (Onboard Power LED indicator) is on, system power is on. Unplug the
power cable before installing or removing any components.
12
Chapter 1: Introduction
Quick Reference Table
Jumper
Description
Default Setting
JI2C1/JI2C2
SMB to PCI Slots
BIOS Recovery
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
See Chapter 2
JBR1
JBT1
Clear CMOS
JPB1
BMC Enable/Disable
VGA Enable
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Pins 1-2 (Reset)
JPG1
JPL1/JPL2
JPME2
JWD1
LAN1/LAN2 Enable
Manufacturing Mode Select
Watch Dog Enable
LED
Description
Status
LE1
Rear UID LED
Bllue: On; Unit Identified
LEDBMC
LEDPWR
BMC Heartbeat LED
Onboard Power LED
Green: Blinking; BMC Normal
Green: Solid On; Power On
Connector
BT1
Description
Onboard Battery
COM1
COM1 Port Header
COM2
COM2 Port Header [X11SSM(-F) only]
System/CPU Fan Headers
FAN1-FAN4, FANA
IPMI LAN
I-SATA0-I-SATA5
I-SATA6 & I-SATA7
I-SGPIO 1/2
JD1
Dedicated IPMI Gigabit (RJ45) Port (X11SSM-F & X11SSL-F only)
(Intel PCH) Serial ATA (SATA) 3.0 Ports
(Intel PCH) Serial ATA (SATA) 3.0 Ports [X11SSM(-F) only]
Serial Link General Purpose I/O Connection Headers 1/2
Speaker/Power LED Indicator
JF1
Front Control Panel Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI Card)
Chassis Intrusion Header
JL1
JPI2C1
Power System Management Bus (Power SMB)
Overheat LED Indicator
JOH1
JPWR1
24-pin ATX Main Power Connector (Required)
+12V 8-pin Power Connector (Required)
SATA DOM (Device_On_Module) Power Connectors
Inject External P5V_STBY Power
JPWR2
JSD1/JSD2
JSTBY1
JTPM1
Trusted Platform Module/Port 80 Connector
Unit Identifier Switch
JUIDB1
LAN1/LAN2
PCI-E (CPU) Slot 7
Gigabit (RJ45) Ports (LAN1/2)
PCI-Express 3.0 x8 Slot
Note: Table is continued on the next page.
13
X11SSM(-F)/X11SSL(-F) User Manual
Connector
PCI-E (CPU) Slot 6
PCI-E (PCH) Slot 5
PCI-E (PCH) Slot 4
SP1
Description
PCI-Express 3.0 x8in x16 Slot
PCI-Express 3.0 x4in x8 Slot
PCI-Express 3.0 x4in x8 Slot [X11SSM(-F) only]
Internal Speaker/Buzzer
USB 0/1
Back Panel USB 2.0 Ports
Front Accessible USB 2.0 Headers
Back Panel USB 3.0 Ports
Front Accessible USB 3.0 Header
USB 3.0 Type-A Header
USB 2/3, USB 4/5
USB 6/7
USB 8/9
USB 10
VGA
Back Panel VGA Port
14
Chapter 1: Introduction
Motherboard Features
Motherboard Features
CPU
•
Intel® Xeon® E3-1200 v6/v5, 7th/6th Gen Core™ i3, Pentium, and Celeron series processor in an LGA1151 (H4) socket
with 80W max TDP.
Memory
•
Four (4) 288-pin DIMM slots support up to 64 GB of SDRAM 72-bit DDR4 unbuffered ECC 2400/2133/1866/1600/1333MHz
memory.
DIMM Size
•
16GB, 8GB, and 4GB, up to 64GB at 1.2V
Note 1: Memory speed support depends on the processors used in the system.
Note 2: For the latest CPU/memory updates, please refer to our website at http://www.supermicro.com/products/
motherboard.
Chipset
•
•
Intel® C236 PCH (X11SSM/-F)
Intel® C232 PCH (X11SSL/-F)
Expansion Slots
•
•
•
Two (2) PCI Express 3.0 x4in x8 slots (PCH slots 4 & 5) [slot 4 on X11SSM(-F) only]
One (1) PCI Express 3.0 x8in x16 slot (CPU slot 6)
One (1) PCI Express 3.0 x8 slot (CPU slot 7)
Network
•
Intel i210 AT Gigabit Ethernet Controllers for LAN1/LAN2
Baseboard Management Controller (BMC)
•
•
Aspeed AST 2400 Baseboard Controller (BMC) supports IPMI 2.0 (-F versions only)
One (1) IPMI_dedicated_LAN located on the rear IO back panel (-F versions only)
Graphics
•
Graphics controller via Aspeed AST2400 BMC
I/O Devices
•
•
•
•
•
•
One (1) serial port on the rear I/O panel (COM1)
One (1) front accessible serial port header (COM2) (X11SSM/-F only)
Six (6) SATA 3.0 ports (I-SATA 0-5)
•
•
Serial (COM) Port
SATA 3.0
Two (2) additional SATA 3.0 ports (I-SATA6-7) (X11SSM/-F only)
Two (2) SuperDOM connectors (I-SATA0 & I-SATA1)
RAID 0, 1, 5, and 10
•
RAID (PCH)
Note: The table above is continued on the next page.
15
X11SSM(-F)/X11SSL(-F) User Manual
Motherboard Features
Peripheral Devices
•
•
•
•
•
Two (2) USB 2.0 ports on the rear I/O panel (USB 0/1)
Two (2) front accessible USB 2.0 headers (USB 2/3, USB 4/5),
Two (2) USB 3.0 ports on the rear I/O panel (USB 6/7)
One (1) front accessible USB 3.0 header (USB 8/9)
One (1) USB 3.0 Type-A header (USB 10)
BIOS
•
•
128Mb AMI BIOS® SPI Flash BIOS
Play and Plug (PnP0, DMI 3.0, ACPI 4.0+, USB Keyboard and SMBIOS
Power Management
•
•
•
•
•
•
•
ACPI Power Management
Power / suspend-state indicator LED
Main switch override mechanism
Riser Card auto-detection
Power-on mode for AC power recovery
Keyboard Wakeup from Soft-Off
CPU Fan auto-off in sleep mode
System Health Monitoring
•
Onboard voltage monitoring for CPU core, CPU VCCIO power (0.95V), CPU VCCSA power (1.05V), memory power (1.2V),
chipset power (1.0V), BMC power (1.2V), +12V, +5V, +5V standby, +3.3V, +3.3V standby, and VBAT.
•
•
•
•
CPU 3-phase switching voltage regulator
CPU/System overheat LED and control
CPU Thermal Trip support
Thermal Monitor 2 (TM2) support
Fan Control
•
•
Fan status monitoring with firmware 4-pin fan speed control via IPMI interface
Low noise fan speed control
System Management
•
•
•
•
•
•
•
•
Trusted Platform Module (TPM) support
PECI (Platform Environment Control Interface) 2.0 support
Node Manager Support (X11SSM-F only)
IPMI View
System resource alert via SuperDoctor® 5
SuperDoctor® 5, Watch Dog, NMI
Chassis intrusion header and detection
Server platform service
Note: The table above is continued on the next page.
16
Chapter 1: Introduction
Motherboard Features
LED Indicators
•
•
•
•
•
CPU/Overheating
Fan Failure
UID/remote UID
LAN activity
HDD activity
Other
•
RoHS 6/6 (Full Compliance, Lead Free)
Dimensions
•
Micro ATX form factor (9.6" x 9.6") (243.84 mm x 243.84 mm)
Note 1: The CPU maximum thermal design power (TDP) is subject to chassis and
heatsink cooling restrictions. For proper thermal management, please check the chas-
sis and heatsink specifications for proper CPU TDP sizing.
Note 2: For IPMI configuration instructions, please refer to the Embedded IPMI Con-
figuration User's Guide available at http://www.supermicro.com/support/manuals/.
17
X11SSM(-F)/X11SSL(-F) User Manual
Figure 1-4.
System Block Diagram
#A-2
#A-1
IMVP 8
3 PHASE for Vcore
80W
#B-2
#B-1
PCI-E X8 Gen3
PCIe3.0 x8 (in x8)
PCIe3.0 x8 (in x16)
#8-15
#0-7
Skt-H4
LGA1151
PCI-E X8 Gen3
DMI3
DMI3 x4
PCI-E x4 Gen3
PCI-E x4 Gen3
PCI-E X1 Gen3
PCI-E X1 Gen3
LAN1
PCIe3.0 x4 (in x8)
PCIe 3.0 x4 (in x8)
RJ45
#9
#1/2/3/4
#5/6/7/8
I210
LAN2
I210
#10
RJ45
RGRMII
LAN3
RTL8211E-VB-CG
RJ45
6.0 Gb/S
PCH
PCI-E X1 Gen1
#11
#9
DDR3
BMC Boot Flash
BMC
AST2400
SPI
USB 2.0
SPI
USB 3.0
USB 2.0
COM1
COM2
VGA CONN
Connector Header
SPI
Temp Sensor
EMC1402-1 *2 at diff SMBUS
MUX
LPC
SPI
BIOS
SYSTEM POWER
FAN SPEED CTRL
FRONT PANEL
TPM Header
Debug Card
Note: This is a general block diagram and may not exactly represent the features on
your motherboard. See the previous pages for the actual specifications of your moth-
erboard.
18
Chapter 1: Introduction
1.2 Processor and Chipset Overview
Built upon the functionality and capability of the Intel E3-1200 v6/v5 series processors
(Socket LGA 1151) and the Intel C236/C232 PCH, the X11SSM(-F)/X11SSL(-F) motherboard
offers maximum I/O expandability, energy efficiency, and data reliability in a 14-nm process
architecture, and is optimized for embedded storage solutions, networking applications, or
cloud-computing platforms.
The Intel E3-1200 v6/v5 and PCH C236/C232 platform supports the following features:
• ACPI Power Management Logic Support, Rev. 4.0a
• Intel® Turbo Boost Technology 2.0 Power Monitoring/Power Control, Turbo Time Parameter
(TAU), and Platform Power Control
• Configurable TDP (cTDP) and Lower-Power Mode
• Adaptive Thermal Management/Monitoring
• PCI-E 3.0, SATA 3.0 with transfer rates of up to 6 Gb/s, xHCI USB with SuperSpeed 3.0
• System Management Bus (SMBus) Specification, Version 2.0
• Integrated Sensor Hub (ISH)
• Intel Trusted Execution Technology (Intel TXT)
• Intel Rapid Storage Technology
• Intel Virtualization Technology for Directed I/O (Intel VT-d)
Note: The Intel C236 PCH is supported by the X11SSM(-F) series. The C232 PCH is
supported by the X11SSL(-F) series.
1.3 Special Features
This section describes the health monitoring features of the X11SSM(-F)/X11SSL(-F)
motherboard. The motherboard has an onboard System Hardware Monitor chip that supports
system health monitoring.
Recovery from AC Power Loss
The Basic I/O System (BIOS) provides a setting that determines how the system will respond
when AC power is lost and then restored to the system. You can choose for the system to
remain powered off (in which case you must press the power switch to turn it back on), or
for it to automatically return to the power-on state. See the Advanced BIOS Setup section
for this setting. The default setting is Last State.
19
X11SSM(-F)/X11SSL(-F) User Manual
1.4 System Health Monitoring
The motherboard has an onboard Baseboard Management Controller (BMC) chip that
supports system health monitoring.
Onboard Voltage Monitors
The onboard voltage monitor will continuously scan crucial voltage levels. Once a voltage
becomes unstable, it will give a warning or send an error message to the screen. Users can
adjust the voltage thresholds to define the sensitivity of the voltage monitor. Real time readings
of these voltage levels are all displayed in BIOS.
Fan Status Monitor with Firmware Control
The system health monitor chip can check the RPM status of a cooling fan. The CPU and
chassis fans are controlled by BIOS Thermal Management through the back panel.
Environmental Temperature Control
System Health sensors monitor temperatures and voltage settings of onboard processors
and the system in real time via the IPMI interface. Whenever the temperature of the CPU or
the system exceeds a user-defined threshold, system/CPU cooling fans will be turned on to
prevent the CPU or the system from overheating
Note: To avoid possible system overheating, please be sure to provide adequate air-
flow to your system.
System Resource Alert
This feature is available when used with SuperDoctor 5 in the Windows OS or in the Linux
environment. SuperDoctor is used to notify the user of certain system events. For example,
you can configure SuperDoctor to provide you with warnings when the system temperature,
CPU temperatures, voltages and fan speeds go beyond a predefined range.
1.5 ACPI Features
ACPI stands for Advanced Configuration and Power Interface. The ACPI specification defines
a flexible and abstract hardware interface that provides a standard way to integrate power
management features throughout a computer system, including its hardware, operating
system and application software. This enables the system to automatically turn on and off
peripherals such as CD-ROMs, network cards, hard disk drives and printers.
20
Chapter 1: Introduction
In addition to enabling operating system-directed power management, ACPI also provides a
generic system event mechanism for Plug and Play, and an operating system-independent
interface for configuration control. ACPI leverages the Plug and Play BIOS data structures,
while providing a processor architecture-independent implementation that is compatible with
Windows 7, Windows 8, and Windows 2012 Operating Systems.
1.6 Power Supply
As with all computer products, a stable power source is necessary for proper and reliable
operation. It is even more important for processors that have high CPU clock rates.
The X11SSM(-F)/X11SSL(-F) motherboard accommodates 24-pin ATX power supplies.
Although most power supplies generally meet the specifications required by the CPU, some
are inadequate. In addition, One 12V 8-pin power connection is also required to ensure
adequate power supply to the system.
Warning: To avoid damaging the power supply or the motherboard, be sure to use a
power supply that contains a 24-pin and one 8-pin power connector. Be sure to con-
nect the power supplies to the 24-pin power connector (JPWR1), and the 8-pin power
connector (JPWR2) on the motherboard. Failure in doing so may void the manufacturer
warranty on your power supply and motherboard.
It is strongly recommended that you use a high quality power supply that meets ATX power
supply Specification 2.02 or above. It must also be SSI compliant. (For more information,
please refer to the website at http://www.ssiforum.org/). Additionally, in areas where noisy
power transmission is present, you may choose to install a line filter to shield the computer
from noise. It is recommended that you also install a power surge protector to help avoid
problems caused by power surges.
1.7 Serial Port
The X11SSM(-F) motherboard supports two serial communication connections. X11SSL(-F)
supports COM Port 1 only. COM Ports 1 and 2 can be used for input/output. The UART
provides legacy speeds with a baud rate of up to 115.2 Kbps as well as an advanced speed
with baud rates of 250 K, 500 K, or 1 Mb/s, which support high-speed serial communication
devices.
21
X11SSM(-F)/X11SSL(-F) User Manual
Chapter 2
Installation
2.1 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic components. To prevent damage to your
motherboard, it is important to handle it very carefully. The following measures are generally
sufficient to protect your equipment from ESD.
Precautions
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing the board from the antistatic bag.
• Handle the board by its edges only; do not touch its components, peripheral chips, memory
modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the motherboard and peripherals back into their antistatic bags when not in use.
• For grounding purposes, make sure that your chassis provides excellent conductivity be-
tween the power supply, the case, the mounting fasteners and the motherboard.
• Use only the correct type of CMOS onboard battery as specified by the manufacturer. Do
not install the CMOS battery upside down, which may result in a possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When unpacking
the motherboard, make sure that the person handling it is static protected.
22
Chapter 2: Installation
2.2 Motherboard Installation
All motherboards have standard mounting holes to fit different types of chassis. Make sure
that the locations of all the mounting holes for both the motherboard and the chassis match.
Although a chassis may have both plastic and metal mounting fasteners, metal ones are
highly recommended because they ground the motherboard to the chassis. Make sure that
the metal standoffs click in or are screwed in tightly.
Philips Screws
(7)
Standoffs (7)
Only if Needed
Philips
Screwdriver
(1)
Tools Needed
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
Location of Mounting Holes
Note: 1) To avoid damaging the motherboard and its components, please do not use
a force greater than 8 lb/inch on each mounting screw during motherboard installation.
2) Some components are very close to the mounting holes. Please take precautionary
measures to avoid damaging these components when installing the motherboard to
the chassis.
23
X11SSM(-F)/X11SSL(-F) User Manual
Installing the Motherboard
1. Install the I/O shield into the back of the chassis.
2. Locate the mounting holes on the motherboard. See the previous page for the location.
3. Locate the matching mounting holes on the chassis. Align the mounting holes on the
motherboard against the mounting holes on the chassis.
4. Install standoffs in the chassis as needed.
5. Install the motherboard into the chassis carefully to avoid damaging other motherboard
components.
6. Using the Phillips screwdriver, insert a Phillips head #6 screw into a mounting hole on
the motherboard and its matching mounting hole on the chassis.
7. Repeat Step 5 to insert #6 screws into all mounting holes.
8. Make sure that the motherboard is securely placed in the chassis.
Note: Images displayed are for illustration only. Your chassis or components might
look different from those shown in this manual.
24
Chapter 2: Installation
2.3 Processor and Heatsink Installation
Warning: When handling the processor package, avoid placing direct pressure on the label
area of the fan.
Important:
• Always connect the power cord last, and always remove it before adding, removing or
changing any hardware components. Make sure that you install the processor into the
CPU socket before you install the CPU heatsink.
• If you buy a CPU separately, make sure that you use an Intel-certified multi-directional
heatsink only.
• Make sure to install the motherboard into the chassis before you install the CPU heatsink.
• When receiving a motherboard without a processor pre-installed, make sure that the plastic
CPU socket cap is in place and none of the socket pins are bent; otherwise, contact your
retailer immediately.
• Refer to the Supermicro website for updates on CPU support.
Installing the LGA1151 Processor
1. Press the load lever to release the load plate, which covers the CPU socket, from its
locking position.
Load Plate
Load Lever
25
X11SSM(-F)/X11SSL(-F) User Manual
2. Gently lift the load lever to open the load plate. Remove the plastic cap.
3. Use your thumb and your index finger to hold the CPU at the North center edge and the
South center edge of the CPU.
North Center Edge
South Center Edge
4. Align the CPU key that is the semi-circle cutouts against the socket keys. Once it is
aligned, carefully lower the CPU straight down into the socket. (Do not drop the CPU on
the socket. Do not move the CPU horizontally or vertically.
26
Chapter 2: Installation
5. Do not rub the CPU against the surface or against any pins of the socket to avoid
damaging the CPU or the socket.
6. With the CPU inside the socket, inspect the four corners of the CPU to make sure that
the CPU is properly installed.
7. Use your thumb to gently push the load lever down to the lever lock.
CPU properly
installed
Load lever locked into
place
Note: You can only install the CPU inside the socket in one direction. Make sure that
it is properly inserted into the CPU socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.
27
X11SSM(-F)/X11SSL(-F) User Manual
Installing an Active CPU
Heatsink with Fan
1. Locate the CPU fan power connector on
the motherboard. (Refer to the layout on
the right for the CPU fan location.)
Thermal Grease
2. Position the heatsink so that the heatsink
fan wires are closest to the CPU fan
power connector and are not interfering
with other components.
Heatsink
Fins
3. Inspect the CPU fan wires to make sure
that the wires are routed through the
bottom of the heatsink.
4. Remove the thin layer of protective film
from the heatsink.
Important: CPU overheating may oc-
cur if the protective film is not removed
from the heatsink.
5. Apply the proper amount of thermal
grease on the CPU.
Note: If your heatsink came with a ther-
mal pad, please ignore this step.
Recommended Supermicro heatsink:
SNK-P0046A4 or SNK-P0051AP4
active heatsink
6. If necessary, rearrange the wires to
make sure that the wires are not pinched
between the heatsink and the CPU. Also
make sure to keep clearance between the
fan wires and the fins of the heatsink.
(2U+ or 4U chassis)
28
Chapter 2: Installation
7. Align the four heatsink fasteners with
the mounting holes on the motherboard.
Gently push the pairs of diagonal
fasteners (#1 & #2, and #3 & #4) into
the mounting holes until you hear a click.
Also, make sure to orient each fastener
so that the narrow end of the groove is
pointing outward.
8. Repeat step 7 to insert all four heatsink
fasteners into the mounting holes.
9. Once all four fasteners are securely
inserted into the mounting holes, and
the heatsink is properly installed on the
motherboard, connect the heatsink fan
wires to the CPU fan connector.
29
X11SSM(-F)/X11SSL(-F) User Manual
Removing the Active Heatsink
Note: We do not recommend that
the CPU or the heatsink be removed.
However, if you do need to remove the
heatsink, please follow the instructions
below to remove the heatsink and to
prevent damage done to the CPU or
other components.
Unplug the
PWR cord
1. Unplug the power cord from the power
supply.
2. Disconnect the heatsink fan wires from
the CPU fan header.
3. Use your finger tips to gently press on the
fastener cap and turn it counterclockwise
to make a 1/4 (900) turn, and pull the
fastener upward to loosen it.
4. Repeat step 3 to loosen all fasteners from
the mounting holes.
Pull Up
5. With all fasteners loosened, remove the
heatsink from the CPU.
30
Chapter 2: Installation
Installing a Passive CPU Heatsink
1. Do not apply thermal grease to the heatsink or the CPU die; the required amount has
already been applied.
2. Place the heatsink on top of the CPU so that the four mounting holes are aligned with
those on the motherboard and the underlying heatsink bracket.
3. Screw in two diagonal screws (the #1 and #2 screws in the figure below) until just snug.
To avoid possible damage to the CPU, do not over tighten the screws.
4. Finish the installation by fully tightening all four screws.
Screw#2
Screw#1
Motherboard
Mounting Holes
Heatsink Bracket
Recommended Supermicro heatsink:
SNK-P0046P passive heatsink
(1U chassis)
31
X11SSM(-F)/X11SSL(-F) User Manual
Removing the Passive Heatsink
Note: We do not recommend that the CPU or the heatsink be removed. However, if
you do need to remove the heatsink, please follow the instructions below to remove
the heatsink and to prevent damage done to the CPU or other components.
1. Unscrew the heatsink screws from the motherboard in the sequence as shown in the
figure below.
2. Gently wriggle the heatsink to loosen it from the CPU. (Do not use excessive force)
3. Once the CPU heatsink is loosened, remove the CPU heatsink from the CPU.
Loosen screws in sequence as
shown.
Screw#4
Screw#1
Screw#2
Motherboard
Screw#3
Heatsink Bracket
32
Chapter 2: Installation
2.4 Memory Support and Installation
Note: Check the Supermicro website for recommended memory modules.
Important: Exercise extreme care when installing or removing DIMM modules to pre-
vent any possible damage.
Memory Support
The X11SSM(-F)/X11SSL(-F) motherboard supports up to 64GB of unbuffered (UDIMM)
DDR4 ECC 2400/2133/1866/1600/1333MHz memory in four memory slots. Populating these
DIMM slots with memory modules of the same type and size will result in interleaved memory,
which will improve memory performance.
DIMM Module Population Configuration
For optimal memory performance, follow the table below when populating memory.
Processors and their Corresponding Memory Modules
CPU#
Corresponding DIMM Modules
CPU
DIMMA1
DIMMA2 DIMMB1
DIMMB2
Memory Module Population for Optimal Performance
Number of
DIMMs
Memory Population Configuration Table
(For memory to work properly, please follow the instructions below.)
2 DIMMs
4 DIMMs
DIMMB2/DIMMA2
DIMMB2/DIMMA2, DIMMB1/DIMMA1
Memory Module Population
DIMM Slots
per Channel
POR Speeds Ranks per
Layer
Count
Supported
Voltage
DIMM Type
FW Base
(MHz)
DIMM
2400, 2133,
1866, 1600,
1333
Unbuffered
DDR4 ECC
2
SR, DR
6
SPS
1.2V1
Memory Module Population
Max Memory
Possible
4GB DRAM
Technology
8GB DRAM
Technology
Single Rank
UDIMM
16GB
(4x 4GB DIMMs)
32GB
(4x 8GB DIMMs)
Dual Rank
UDIMMs
32GB
(4x 8GB DIMMs)
64GB
(4x 16GB DIMMs)
33
X11SSM(-F)/X11SSL(-F) User Manual
DIMM Module Population Sequence
When installing memory modules, the DIMM slots should be populated in the following order:
DIMMB2, DIMMA2, DIMMB1, DIMMA1.
• Always use DDR4 DIMM modules of the same type, size and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the
slowest DIMM.
• The motherboard will support odd-numbered modules (1 or 3 modules installed). However,
for best memory performance, install DIMM modules in pairs to activate memory interleav-
ing.
Towards the CPU
DIMMA1
DIMMA2 (Blue Slot)
DIMMB1
DIMMB2 (Blue Slot)
Towards the edge of the motherboard
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
DIMMB2
DIMMA1
DIMMA2
DIMMB1
34
Chapter 2: Installation
VGA
LAN2
LAN1
LE1
JUIDB1
USB6/7
(3.0)
USB0/1
DIMM Installation
COM1
BMC
IPMI_LAN
LED BMC
1. Insert the desired number of DIMMs into
the memory slots, starting with DIMMB2
(Channel B, Slot 2, blue slot). For best
performance, please use the memory
modules of the same type and speed in
the same bank.
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
2. Push the release tabs outwards on both
ends of the DIMM slot to unlock it.
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
3. Align the key of the DIMM module with the
receptive point on the memory slot.
4. Align the notches on both ends of the
module against the receptive points on the
ends of the slot.
5. Use two thumbs together to press the
notches on both ends of the module
straight down into the slot until the module
snaps into place.
Notches
6. Press the release tabs to the lock positions
to secure the DIMM module into the slot.
Release Tabs
DIMM Removal
Press both release tabs on the ends of the
DIMM module to unlock it. Once the DIMM
module is loosened, remove it from the
memory slot.
Press both notches
straight down into
the memory slot.
35
X11SSM(-F)/X11SSL(-F) User Manual
2.5 Rear I/O Ports
See Figure 2-2 below for the locations and descriptions of the various I/O ports on the rear
of the motherboard.
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
Figure 2-2. I/O Port Locations and Definitions
2
5
10
1
3
4
6
7
8
9
Rear I/O Ports
#
1.
2.
3
Description
COM1 Port
IPMI LAN
USB1
#
6.
7.
8
Description
USB6 (3.0)
LAN1
LAN2
4
USB0
9
VGA Port
5.
USB7 (3.0)
10 UID Switch
36
Chapter 2: Installation
VGA Port
A video (VGA) port is located next to LAN2 on the I/O back panel. Refer to the board layout
below for the location.
Serial Ports
One COM connection (COM1) is located on X11SSM(-F)/X11SSL(-F), on the I/O back panel.
X11SSM(-F) has an additional COM connection (COM2) located next to COM1. See the table
below for pin definitions.
COM Port
Pin Definitions
Pin#
1
Definition
DCD
Pin#
6
Definition
DSR
RTS
CTS
RI
2
RXD
7
3
TXD
8
4
DTR
9
5
Ground
10
N/A
1
2
VGA
LAN2
LAN1
1. VGA Port
2. COM1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
3
3. COM2 (X11SSM/-F
only)
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
37
X11SSM(-F)/X11SSL(-F) User Manual
LAN Ports
Two Gigabit Ethernet ports (LAN1 and LAN2) are located on the I/O back panel on the
motherboard. In addition, a dedicated IPMI LAN is located above USB 0/1 ports on the
back panel on the -F boards. All of these ports accept RJ45 cables. Please refer to the LED
Indicator section for LAN LED information.
IPMI_LAN (-F versions only)
LAN Ports 1/2
Pin Definition
Pin Definition
Pin#
Definition
Pin#
Definition
Pin#
1
Definition
TD0-
Pin#
11
Definition
9
19
GND
P3V3_Dual
Act LED (Yellow)
Act LED
(Yellow)
2
TD0+
12
10
11
12
TD0+
TD0-
TD1+
20
21
22
Link 1000 LED
(Amber)
3
4
TD1-
13
14
Link 100 LED
(Green)
Link 100 LED
(Green)
TD1+
Link 1000 LED
(Amber)
5
TD2-
15
16
17
18
GND
GND
GND
GND
13
14
15
16
17
18
TD1-
TD2+
TD2-
TD3+
TD3-
GND
23
24
25
26
SGND
SGND
SGND
SGND
6
TD2+
TD3-
7
8
TD3+
COMMCT
GND
9
10
2
LAN2
1
LAN1
3
VGA
USB0/1
LE1
USB6/7
(3.0)
1. LAN1
2. LAN2
JUIDB1
COM1
BMC
IPMI_LAN
LED BMC
3. IPMI LAN (-F
JPL2
JPL1
versions only)
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
38
Chapter 2: Installation
Universal Serial Bus (USB) Ports
There are two USB 2.0 ports (USB0/1) and two USB 3.0 ports (USB6/7) located on the I/O
back panel. The motherboard also has two front access USB 2.0 headers (USB2/3 and
USB4/5) and one front access USB 3.0 header (USB8/9). The USB10 header is USB 3.0
Type A. The onboard headers can be used to provide front side USB access with a cable
(not included).
Back Panel USB (2.0) 0/1
Pin Definitions
Pin#
1
Definition
+5V
Pin#
5
Definition
+5V
2
USB_N
USB_P
Ground
6
USB_N
USB_P
Ground
3
7
4
8
Front Panel USB (2.0) 2/3, 4/5
Pin Definitions
Pin#
1
Definition
+5V
Pin#
2
Definition
+5V
3
USB_N
USB_P
Ground
Key
4
USB_N
USB_P
Ground
NC
5
6
7
8
9
10
Back Panel USB 6/7 (3.0)
Pin Definitions
Pin#
Definition
Pin#
19
18
17
16
15
14
13
12
11
x
Definition
1
VBUS
Power
2
Stda_SSRX-
Stda_SSRX+
GND
USB3_RN
USB3_RP
GND
3
4
5
Stda_SSTX-
Stda_SSTX+
GND
USB3_TN
USB3_TP
GND
6
7
8
D-
USB_N
USB_P
9
D+
10
39
X11SSM(-F)/X11SSL(-F) User Manual
Front Panel USB 8/9 (3.0)
Pin Definitions
Pin#
A1
A2
A3
A4
A5
A6
A7
A8
A9
Definition
VBUS
Pin#
B1
B2
B3
B4
B5
B6
B7
B8
B9
Definition
Power
D-
USB_N
USB_P
GND
D+
GND
Stda_SSRX-
Stda_SSRX+
GND
USB3_RN
USB3_RP
GND
Stda_SSTX-
Stda_SSTX+
USB3_TN
USB3_TP
Type A USB 10 (3.0)
Pin Definitions
Pin#
1
Definition
Pin#
5
Definition
VBUS
SSRX-
SSRX+
GND
2
USB_N
USB_P
Ground
6
3
7
4
8
SSTX-
SSTX+
9
4
USB6/7
(3.0)
1
USB0/1
VGA
LAN2
LAN1
LE1
1. USB0/1
2. USB2/3
3. USB4/5
4. USB6/7
5. USB8/9
6. USB10
JUIDB1
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
2
USB2/3
JL1
JBT1
BT1
Intel PCH
3
I-SATA7
6
USB10(3.0)
5
JF1
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
40
Chapter 2: Installation
2.6 Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally located on a
control panel at the front of the chassis. These connectors are designed specifically for use
with Supermicro chassis. See the figure below for the descriptions of the front control panel
buttons and LED indicators.
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
Figure 2-3. JF1 Header Pins
1
2
Power Button PWR
Ground
Ground
Reset Button
Reset
P3V3
Power Fail LED
OH/Fan Fail LED
UID LED
P3V3_STBY
P3V3_STBY
NIC2 Link Active LED
NIC1 Link Active LED
HDD LED
P3V3_STBY/ID_UID_SW
FP PWRLED
NC
P3V3
NC
SW_NMI_N
Ground
19 20
41
X11SSM(-F)/X11SSL(-F) User Manual
Power Button
The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both
pins will power on/off the system. This button can also be configured to function as a suspend
button (with a setting in the BIOS - see Chapter 4). To turn off the power when the system
is in suspend mode, press the button for 4 seconds or longer. Refer to the table below for
pin definitions.
Power Button
Pin Definitions (JF1)
Pin# Definition
1
2
Signal
Ground
Reset Button
The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset
switch on the computer case. Refer to the table below for pin definitions.
Reset Button
Pin Definitions (JF1)
Pin# Definition
3
4
Reset
Ground
1
2
1. PWR Button
2. Reset Button
Power Button PWR
Ground
Ground
Power Fail LED
1
2
Reset Button
Reset
P3V3
OH/Fan Fail LED
UID LED
P3V3_STBY
P3V3_STBY
NIC2 Link Active LED
NIC1 Link Active LED
HDD LED
FP PWRLED
NC
P3V3_STBY/ID_UID_SW
P3V3
NC
SW_NMI_N
Ground
19 20
42
Chapter 2: Installation
Power Fail LED
The Power Fail LED connection is located on pins 5 and 6 of JF1. Refer to the table below
for pin definitions.
Power Fail LED
Pin Definitions (JF1)
Pin# Definition
5
6
3.3V
PWR Supply Fail
Overheat (OH)/Fan Fail
Connect an LED cable to pins 7 and 8 of the Front Control Panel to use the Overheat/Fan
Fail LED connections. The LED on pin 8 provides warnings of overheat or fan failure. Refer
to the tables below for pin definitions.
OH/Fan Fail Indicator
Status
OH/Fan Fail LED
Pin Definitions (JF1)
State
Off
Definition
Normal
Pin# Definition
7
8
Blue LED
On
Overheat
OH/Fan Fail LED
Flashing Fan Fail
1
2
1. PWR Fail LED
Power Button PWR
Ground
Ground
Reset Button
Reset
2. OH/Fan Fail LED
Power Fail LED
P3V3
UID LED
1
OH/Fan Fail LED
2
NIC2 Link Active LED
NIC1 Link Active LED
HDD LED
P3V3_STBY
P3V3_STBY
P3V3_STBY/ID_UID_SW
FP PWRLED
NC
P3V3
NC
SW_NMI_N
Ground
19 20
43
X11SSM(-F)/X11SSL(-F) User Manual
NIC1/NIC2 (LAN1/LAN2)
The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pins 11
and 12 of JF1, and the LED connection for LAN port 2 is on pins 9 and 10. Attach the NIC
LED cables here to display network activity. Refer to the table below for pin definitions.
LAN1/LAN2 LED
Pin Definitions (JF1)
Pin# Definition
9
NIC 2 Activity LED
NIC 2 Link LED
NIC 1 Activity LED
NIC 1 Link LED
10
11
12
HDD LED/UID Switch
The HDD LED/UID Switch connection is located on pins 13 and 14 of JF1. Attach a cable to
pin 14 to show hard drive activity status. Attach a cable to Pin 13 to use UID switch. Refer
to the table below for pin definitions.
HDD LED
Pin Definitions (JF1)
Pin# Definition
13
14
3.3V Stdby/UID_SW
HDD Active
1
2
Power Button PWR
1. NIC2 LED
Ground
Reset Button
Reset
P3V3
2. NIC1 LED
Ground
Power Fail LED
3. HDD LED / UID Switch
OH/Fan Fail LED
UID LED
P3V3_STBY
NIC2 Link Active LED
NIC1 Link Active LED
1
2
P3V3_STBY
HDD LED
P3V3_STBY/ID_UID_SW
3
FP PWRLED
NC
P3V3
NC
SW_NMI_N
Ground
19 20
44
Chapter 2: Installation
Power LED
The Power LED connection is located on pins 15 and 16 of JF1. Refer to the table below
for pin definitions.
Power LED
Pin Definitions (JF1)
Pin# Definition
15 3.3V
16 PWR LED
NMI Button
The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the
table below for pin definitions.
NMI Button
Pin Definitions (JF1)
Pin# Definition
19
20
Control
Ground
1
2
1. PWR LED
Power Button PWR
Ground
Ground
Reset Button
Reset
P3V3
2. NMI
Power Fail LED
OH/Fan Fail LED
UID LED
P3V3_STBY
NIC2 Link Active LED
NIC1 Link Active LED
P3V3_STBY
HDD LED
P3V3_STBY/ID_UID_SW
P3V3
FP PWRLED
1
NC
NC
SW_NMI_N
2
Ground
19 20
45
X11SSM(-F)/X11SSL(-F) User Manual
2.7 Connectors
Power Connections
Main ATX Power Supply Connector
The primary power supply connector (JPWR1) meets the ATX SSI EPS 12V specification.
You must also connect the 8-pin (JPWR2) processor power connector to your power supply.
ATX Power 24-pin Connector
Pin Definitions
Pin#
13
14
15
16
17
18
19
20
21
22
23
24
Definition
+3.3V
Pin#
1
Definition
+3.3V
+3.3V
Ground
+5V
-12V
2
Ground
PS_ON
Ground
Ground
Ground
Res (NC)
+5V
3
4
5
Ground
+5V
6
7
Ground
PWR_OK
5VSB
8
9
+5V
10
11
12
+12V
+5V
+12V
Ground
+3.3V
Required Connection
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. 24-Pin ATX Main PWR
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
1
FAN2
FAN1
I-SATA2
FANA FAN3
46
Chapter 2: Installation
Secondary Power Connector
JPWR2 must also be connected to the power supply. This connector is used to power the
processor(s).
+12V 8-pin Power
Pin Definitions
Pin#
Definition
1 - 4 Ground
5 - 8 +12V
Required Connection
Important: To provide adequate power supply to the motherboard, be sure to connect
the 24-pin ATX PWR and the 8-pin PWR connectors to the power supply. Failure to
do so may void the manufacturer warranty on your power supply and motherboard.
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. 8-Pin PWR
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
1
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
47
X11SSM(-F)/X11SSL(-F) User Manual
Headers
Fan Headers
The X11SSM(-F)/X11SSL(-F) has five fan headers (Fan1-Fan4, FanA). All of these 4-pin fan
headers are backwards-compatible with the traditional 3-pin fans. However, fan speed control
is available for 4-pin fans only by Thermal Management via the IPMI 2.0 interface. Refer to
the table below for pin definitions.
Fan Header
Pin Definitions
Pin#
1
Definition
Ground (Black)
2.5A/+12V (Red)
Tachometer
2
3
4
PWM_Control
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. FANA
2. FAN1
3. FAN2
4. FAN3
5. FAN4
5
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
1 4
3
2
48
Chapter 2: Installation
Chassis Intrusion
A Chassis Intrusion header is located at JL1 on the motherboard. Attach the appropriate cable
from the chassis to inform you of a chassis intrusion when the chassis is opened. Refer to
the table below for pin definitions.
Chassis Intrusion
Pin Definitions
Pin#
1
Definition
Intrusion Input
Ground
2
Internal Speaker/Buzzer
The Internal Speaker (SP1) can be used to provide audible notifications using various beep
codes. Refer to the table below for pin definitions. Refer to the layout below for the location
of the internal buzzer.
Internal Buzzer
Pin Definitions
Pin#
1
Definition
Pos (+)
Beep In
2
Neg (-)
Alarm Speaker
VGA
LAN2
LAN1
USB0/1
COM1
LE1
JUIDB1
USB6/7
(3.0)
1. Chassis Intrusion
2. Internal Buzzer
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
2
CPU
USB2/3
JL1
1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
49
X11SSM(-F)/X11SSL(-F) User Manual
Power LED/Speaker
Pins 1-3 of JD1 are used for power LED indication, and pins 4-7 are for the speaker. Please
note that the speaker connector pins (4-7) are used with an external speaker. If you wish to
use the onboard speaker, you should close pins 6-7 with a cap. Refer to the tables below
for pin definitions.
PWR LED Connector
Speaker Connector
Pin Definitions
Pin Definitions
Pin Setting Definition
Pin Setting Definition
1
2
3
JD1_PIN1
4
5
6
7
P5V
FP_PWR_LED
FP_PWR_LED
Key
R_SPKPIN_N
R_SPKPIN
Overheat/Fan Fail LED Header
The JOH1 header is used to connect an LED indicator to provide warnings of chassis
overheating and fan failure. This LED will blink when a fan failure occurs. Refer to the tables
below for pin definitions.
Overheat LED Header
Status
Overheat LED
Pin Definitions
State
Definition
Overheat
Fan Fail
Pin#
Definition
5vDC
Solid
1
2
Blinking
OH Active
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. Speaker Header
BMC
IPMI_LAN
2. Overheat/Fan Fail
LED Header
LED BMC
2
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
1
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
50
Chapter 2: Installation
Disk-On-Module Power Connector
Two power connectors for SATA DOM (Disk_On_Module) devices are located at JSD1/JSD2.
Connect appropriate cables here to provide power support for your Serial Link DOM devices.
DOM Power
Pin Definitions
Pin#
1
Definition
5V
2
Ground
Ground
3
Standby Power
The +5V Standby Power header is located at JSTBY1 on the motherboard. You must have
a card with a Standby Power connector and a cable to use this feature. Refer to the table
below for pin definitions.
Wake-On-LAN
Pin Definitions
Pin#
1
Definition
+5V Standby
Ground
2
3
Wake-up
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. JSD 1 (DOM PWR)
2. JSD 2 (DOM PWR)
3. Standby PWR
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
3
I-SATA7
2
1
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
51
X11SSM(-F)/X11SSL(-F) User Manual
SGPIO Headers
Two I-SGPIO (Serial Link General Purpose Input/Output) headers are located on the
motherboard. They support the onboard I-SATA 3.0 ports. Refer to the table below for pin
definitions.
SGPIO Header
I-SGPIO 1/2
Pin Definitions
I-SGPIO1
I-SGPIO2
I-SATA 3.0 Ports 0-3
I-SATA 3.0 Ports 4-7
Pin#
1
Definition Pin#
Definition
NC
NC
2
4
6
8
3
GND
Load
Clock
Data
GND
NC
5
7
NC = No Connection
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. I-SGPIO 1
2. I-SGPIO 2
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
1
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
2
52
Chapter 2: Installation
TPM/Port 80 Header
A Trusted Platform Module (TPM)/Port 80 header is located at JTPM1 to provide TPM support
and a Port 80 connection. Use this header to enhance system performance and data security.
Refer to the table below for pin definitions.
Trusted Platform Module Header
Pin Definitions
Pin#
1
Definition
LCLK
Pin#
2
Definition
GND
3
LFRAME#
LRESET#
LAD3
4
<(KEY)>
+5V
5
6
7
8
LAD2
9
+3.3V
10
12
14
16
18
20
LAD1
11
13
15
17
19
LAD0
GND
SMB_CLK
+3V Stdby
GND
SMB_DAT
SERIRQ
CLKRUN#
LDRQ#
LPCPD#
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. TPM Header
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
1
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
53
X11SSM(-F)/X11SSL(-F) User Manual
Power SMB (I2C) Header
The Power System Management Bus (I2C) connector (JPI2C1) monitors the power supply,
fan, and system temperatures. Refer to the table below for pin definitions.
Power SMB Header
Pin Definitions
Pin#
1
Definition
Clock
2
Data
3
PMBUS_Alert
Ground
+3.3V
4
5
4-pin BMC External I2C Header
A System Management Bus header for IPMI 2.0 is located at JIPMB1. Connect the appropriate
cable here to use the IPMB I2C connection on your system. Refer to the table below for pin
definitions.
External I2C Header
Pin Definitions
Pin#
1
Definition
Data
2
GND
3
Clock
NC
4
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. Power SMB Header
2. BMC External Header
BMC
IPMI_LAN
LED BMC
2
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
1
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
54
Chapter 2: Installation
SATA Ports
Six SATA 3.0 connectors are located on the X11SSM(-F)/X11SSL(-F) motherboard, supported
by the Intel C232/C236 PCH chip. These SATA ports support RAID 0, 1, 5, and 10. SATA
ports provide serial-link signal connections, which are faster than the connections of Parallel
ATA. See the tables below for pin definitions. Two additional SATA 3.0 connectors (I-SATA
6-7) are located on the X11SSM(-F) motherboard.
Note 1: I-SATA0 and I-SATA1 are Supermicro SuperDOMs. These are yellow SATA-
DOM connectors with power pins built in and do not require separate external power
cables. These connectors are backward-compatible with non-Supermicro SATADOMs
that require an external power supply.
Note 2: For more information on the SATA HostRAID configuration, please refer to the
Intel SATA HostRAID user's guide posted on our website at http://www.supermicro.com.
X11SSM(-F)/X11SSL(-F) SATA 3.0 Connector Types
SATA 3.0 Port
Pin Definitions
Port #
Connection Type
Pin#
1
Signal
SATA 3.0/6 Gb/s
Ground
I-SATA0-1 (Two)
RAID 0, 1, 5, 10
2
SATA_TXP
SATA_TXN
Ground
SuperDOM connectors
3
SATA 3.0/6 Gb/s
RAID 0, 1, 5, 10
I-SATA2-5 (Four)
Supported by
4
5
SATA_RXN
SATA_RXP
Ground
Intel C232/C236 PCH-Exp.
6
I-SATA 6-7 (Two)
[X11SSM(-F) only]
SATA 3.0/6 Gb/s
RAID 0, 1, 5, and 10
7
Supported by
Intel C236 PCH
VGA
LAN2
LAN1
1. I-SATA0
2. I-SATA1
3. I-SATA2
4. I-SATA3
5. I-SATA4
6. I-SATA5
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
7. I-SATA6 (X11SSM/-F
only)
CPU
USB2/3
JL1
8. I-SATA7 (X11SSM/-F
only)
JBT1
BT1
Intel PCH
8
I-SATA7
JF1
USB10(3.0)
7
5
LED PWR
6
4
1
FAN2
FAN1
I-SATA2
FANA FAN3
3
2
55
X11SSM(-F)/X11SSL(-F) User Manual
Unit Identifier Switch/UID LED Indicator
A Unit Identifier (UID) switch and an LED Indicator are located on the motherboard. The UID
switch is located at JUIDB1, which is next to the VGA port on the back panel. The UID LED
(LE1) is located next to the UID switch. When you press the UID switch, the UID LED will
be turned on. Press the UID switch again to turn off the LED indicator. The UID Indicator
provides easy identification of a system unit that may be in need of service.
Note: UID can also be triggered via IPMI on the motherboard. For more information
on IPMI, please refer to the IPMI User's Guide posted on our website at http://www.
supermicro.com.
UID Switch
UID LED
Pin Definitions
Pin Definitions
Pin#
Definition
Ground
Color
Status
1
2
3
4
Blue: On
Unit Identified
Ground
Button In
Button In
1
2
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. UID Switch
2. UID LED
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
56
Chapter 2: Installation
2.8 Jumper Settings
How Jumpers Work
To modify the operation of the motherboard, jumpers can be used to choose between optional
settings. Jumpers create shorts between two pins to change the function of the connector.
Pin 1 is identified with a square solder pad on the printed circuit board. See the diagram
below for an example of jumping pins 1 and 2. Refer to the motherboard layout page for
jumper locations.
Note: On two-pin jumpers, "Closed" means the jumper is on and "Open" means the
jumper is off the pins.
3
2
1
Connector
Pins
Jumper
Setting
3
2
1
57
X11SSM(-F)/X11SSL(-F) User Manual
CMOS Clear
JBT1 is used to clear the CMOS. Instead of pins, this "jumper" consists of contact pads to
prevent accidental clearing of the CMOS. To clear the CMOS, use a metal object such as a
small screwdriver to touch both pads at the same time to short the connection.
Note: Be sure to completely shut down the system, and then short JBT1 to clear the
CMOS.
LAN Port Enable/Disable
Jumpers JPL1/JPL2 enable or disable LAN ports 1/2 on the motherboard. Refer to the table
below for jumper settings. The default setting is Enabled.
LAN1-LAN4 Enable/Disable
Jumper Settings
Jumper Setting
Pins 1-2
Definition
Enabled
Disabled
Pins 2-3
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. CMOS Clear
2. LAN1 Port Enable/
BMC
IPMI_LAN
LED BMC
3
JPL2
2
JPL1
Disable
3. LAN2 Port Enable/
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Disable
Designed in the USA
SP1
CPU
USB2/3 1
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
58
Chapter 2: Installation
Watch Dog
Watch Dog (JWD1) is a system monitor that can reboot the system when a software
application hangs. Close pins 1-2 to reset the system if an application hangs. Close pins 2-3
to generate a non-maskable interrupt (NMI) signal for the application that hangs. Refer to the
table below for jumper settings. The Watch Dog must also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting
Pins 1-2
Pins 2-3
Open
Definition
Reset
NMI
Disabled
SMBus to PCI Slots
Use jumpers JI2C1 and JI2C2 to connect the System Management Bus (I2C) to PCI-Express
slots to improve PCI performance. These two jumpers should be set at the same time. Refer
to the table below for jumper settings. The default setting is Enabled.
I2C for PCI-E Slots
Jumper Settings
Jumper Setting
Pins 1-2
Definition
Enabled
Disabled
Pins 2-3
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. Watch Dog
2. SMBus to PCI Slots
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
2
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
1
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
59
X11SSM(-F)/X11SSL(-F) User Manual
VGA Enable/Disable
Jumper JPG1 allows the user to enable the onboard VGA connector. The default setting is
pins 1-2 to enable the connection. Refer to the table below for jumper settings.The default
setting is Enabled.
VGA Enable/Disable
Jumper Settings
Jumper Setting
Pins 1-2
Definition
Enabled
Disabled
Pins 2-3
BIOS Recovery
Use jumper JBR1 to recover the BIOS settings on the motherboard. Refer to the table below
for jumper settings. The default setting is Normal.
BIOS Recovery
Jumper Settings
Jumper Setting
Pins 1-2
Definition
Normal
Pins 2-3
BIOS Recovery
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
1. VGA Enable
COM1
2. BIOS Recovery
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
2
1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
60
Chapter 2: Installation
BMC Enabled
Jumper JPB1 allows the user to enable the embedded ASpeed AST2400 Baseboard
Management Controller (BMC) to provide IPMI 2.0/KVM support on the motherboard. Refer
to the table below for jumper settings. The default setting is BMC Enable.
BMC Enable
Jumper Settings
Jumper Setting
Pins 1-2
Definition
BMC Enabled
Disabled
Pins 2-3
Manufacturer Mode Select
Close pin 2 and pin 3 of jumper JPME2 to bypass SPI flash security and force the system to
operate in the manufacturer mode, which will allow the user to flash the system firmware from
a host server for system setting modifications. Refer to the table below for jumper settings.
The default setting is Normal.
Manufacturer Mode
Jumper Settings
Jumper Setting
Pins 1-2
Definition
Normal
Pins 2-3
Manufacturer Mode
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
1. BMC Enable
COM1
2. Manufacturer Mode
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
2
X11SSM(-F)/X11SSL(-F)
REV:1.01
1
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
61
X11SSM(-F)/X11SSL(-F) User Manual
2.9 LED Indicators
LAN LEDs
Two LAN ports (LAN 1 and LAN 2) are located on the I/O back panel of the motherboard.
Each Ethernet LAN port has two LEDs. The green LED indicates activity, while the other Link
LED may be green, amber, or off to indicate the speed of the connection. Refer to the tables
below for more information.
LAN1/2 Activity LED (Right)
LED State
LAN1/2 Link LED (Left)
LED State
Color
Status
Definition
LED Color
Off
Definition
Green
Flashing
Active
No Connection/10 Mbps
1 Gbps
Amber
Green
100 Mbps
2
1
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. LAN1 LED
2. LAN2 LED
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
62
Chapter 2: Installation
IPMI-Dedicated LAN LEDs (-F versions only)
In addition to LAN 1 and LAN 2, an IPMI LAN is also located on the I/O back panel. The
amber LED on the right indicates activity, while the green LED on the left indicates the speed
of the connection. Refer to the table below for more information.
IPMI LAN
IPMI LAN LEDs
Link LED
Activity LED
Color/State
Definition
Green: Solid
Amber: Solid
100 Mbps
1Gbps
Link (left)
Activity (Right)
Amber: Blinking
Active
Onboard Power LED
The Onboard Power LED is located at LEDPWR on the motherboard. When this LED is on,
the system is on. Be sure to turn off the system and unplug the power cord before removing
or installing components. Refer to the table below for more information.
Onboard Power LED Indicator
LED Color
Definition
System Off
(power cable not
connected)
System On
Off
Green
1
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. IPMI LAN
2. Onboard PWR LED
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
2
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
63
X11SSM(-F)/X11SSL(-F) User Manual
BMC Heartbeat LED
A BMC Heartbeat LED is located at LEDBMC on the motherboard. When LEDBMC is blinking,
the BMC is functioning normally. Refer to the table below for more information.
BMC Heartbeat LED Indicator
LED Color
Green:
Definition
BMC: Normal
Blinking
VGA
LAN2
LAN1
USB0/1
LE1
JUIDB1
USB6/7
(3.0)
COM1
1. BMC Heartbeat LED
1
BMC
IPMI_LAN
LED BMC
JPL2
JPL1
MAC CODE
X11SSM(-F)/X11SSL(-F)
REV:1.01
Designed in the USA
SP1
CPU
USB2/3
JL1
JBT1
BT1
Intel PCH
I-SATA7
JF1
USB10(3.0)
LED PWR
FAN2
FAN1
I-SATA2
FANA FAN3
64
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3.1 Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all of the
procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/
or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC
power cord before adding, changing or installing any non hot-swap hardware components.
Before Power On
1. Make sure that there are no short circuits between the motherboard and chassis.
2. Disconnect all ribbon/wire cables from the motherboard, including those for the keyboard
and mouse.
3. Remove all add-on cards.
4. Install the CPU first (making sure it is fully seated) and connect the front panel
connectors to the motherboard.
No Power
1. Make sure that there are no short circuits between the motherboard and the chassis.
2. Make sure that the ATX power connectors are properly connected.
3. Check that the 115V/230V switch, if available, on the power supply is properly set.
4. Turn the power switch on and off to test the system, if applicable.
5. The battery on your motherboard may be old. Check to verify that it still supplies
~3VDC. If it does not, replace it with a new one.
No Video
1. If the power is on but you have no video, remove all the add-on cards and cables.
2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for details on
beep codes.
65
X11SSM(-F)/X11SSL(-F) User Manual
3. Remove all memory modules and turn on the system (if the alarm is on, check the
specs of memory modules, reset the memory or try a different one).
System Boot Failure
If the system does not display POST (Power-On-Self-Test) or does not respond after the
power is turned on, check the following:
1. Check for any error beep from the motherboard speaker.
• If there is no error beep, try to turn on the system without DIMM modules installed. If there
is still no error beep, replace the motherboard.
• If there are error beeps, clear the CMOS settings by unplugging the power cord and
contacting both pads on the CMOS Clear Jumper (JBT1). Refer to Chapter 2.
2. Remove all components from the motherboard, especially the DIMM modules. Make
sure that system power is on and that memory error beeps are activated.
3. Turn on the system with only one DIMM module installed. If the system boots, check for
bad DIMM modules or slots by following the Memory Errors Troubleshooting procedure
in this Chapter.
Memory Errors
When a no-memory beep code is issued by the system, check the following:
1. Make sure that the memory modules are compatible with the system and that the
DIMMs are properly and fully installed. (For memory compatibility, refer to the memory
compatibility chart posted on our website at http://www.supermicro.com.)
2. Check if different speeds of DIMMs have been installed. It is strongly recommended that
you use the same RAM type and speed for all DIMMs in the system.
3. Make sure that you are using the correct type of UDIMM ECC DDR4 modules
recommended by the manufacturer.
4. Check for bad DIMM modules or slots by swapping a single module among all memory
slots and check the results.
66
Chapter 3: Troubleshooting
5. Make sure that all memory modules are fully seated in their slots. Follow the instructions
given in Section 2-4 in Chapter 2.
6. Please follow the instructions given in the DIMM population tables listed in Section 2-4
to install your memory modules.
Losing the System's Setup Configuration
1. Make sure that you are using a high-quality power supply. A poor-quality power supply
may cause the system to lose the CMOS setup information. Refer to Chapter 2 for
details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still supplies
~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the setup configuration problem, contact your vendor for
repairs.
When the System Becomes Unstable
A. If the system becomes unstable during or after OS installation, check the following:
1. CPU/BIOS support: Make sure that your CPU is supported and that you have the latest
BIOS installed in your system.
2. Memory support: Make sure that the memory modules are supported by testing the
modules using memtest86 or a similar utility.
Note: Refer to the product page on our website at http:\\www.supermicro.com for
memory and CPU support and updates.
3. HDD support: Make sure that all hard disk drives (HDDs) work properly. Replace the
bad HDDs with good ones.
4. System cooling: Check the system cooling to make sure that all heatsink fans and CPU/
system fans, etc., work properly. Check the hardware monitoring settings in the IPMI
to make sure that the CPU and system temperatures are within the normal range. Also
check the front panel Overheat LED and make sure that it is not on.
5. Adequate power supply: Make sure that the power supply provides adequate power to
the system. Make sure that all power connectors are connected. Please refer to our
website for more information on the minimum power requirements.
67
X11SSM(-F)/X11SSL(-F) User Manual
6. Proper software support: Make sure that the correct drivers are used.
B. If the system becomes unstable before or during OS installation, check the following:
1. Source of installation: Make sure that the devices used for installation are working
properly, including boot devices such as CD/DVD and CD/DVD-ROM.
2. Cable connection: Check to make sure that all cables are connected and working
properly.
3. Using the minimum configuration for troubleshooting: Remove all unnecessary
components (starting with add-on cards first), and use the minimum configuration (but
with the CPU and a memory module installed) to identify the trouble areas. Refer to the
steps listed in Section A above for proper troubleshooting procedures.
4. Identifying bad components by isolating them: If necessary, remove a component in
question from the chassis, and test it in isolation to make sure that it works properly.
Replace a bad component with a good one.
5. Check and change one component at a time instead of changing several items at the
same time. This will help isolate and identify the problem.
6. To find out if a component is good, swap this component with a new one to see if the
system will work properly. If so, then the old component is bad. You can also install the
component in question in another system. If the new system works, the component is
good and the old system has problems.
68
Chapter 3: Troubleshooting
3.2 Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, please note that as
a motherboard manufacturer, Supermicro also sells motherboards through its channels, so it
is best to first check with your distributor or reseller for troubleshooting services. They should
know of any possible problems with the specific system configuration that was sold to you.
1. Please go through the Troubleshooting Procedures and Frequently Asked Questions
(FAQ) sections in this chapter or see the FAQs on our website (http://www.supermicro.
com/) before contacting Technical Support.
2. BIOS upgrades can be downloaded from our website (http://www.supermicro.com).
3. If you still cannot resolve the problem, include the following information when contacting
Supermicro for technical support:
• Motherboard model and PCB revision number
• BIOS release date/version (This can be seen on the initial display when your system first
boots up.)
• System configuration
4. An example of a Technical Support form is on our website at http://www.supermicro.com/
RmaForm/.
• Distributors: For immediate assistance, please have your account number ready when
placing a call to our Technical Support department. We can be reached by email at sup-
port@supermicro.com.
69
X11SSM(-F)/X11SSL(-F) User Manual
3.3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The motherboard supports ECC DDR4 UDIMM modules. To enhance memory
performance, do not mix memory modules of different speeds and sizes. Please follow all
memory installation instructions given in Chapter 2.
Question: How do I update my BIOS?
Answer: It is recommended that you do not upgrade your BIOS if you are not experiencing
any problems with your system. Updated BIOS files are located on our website at http://www.
supermicro.com. Please check our BIOS warning message and the information on how to
update your BIOS on our website. Select your motherboard model and download the BIOS
file to your computer. Also, check the current BIOS revision to make sure that it is newer
than your BIOS before downloading. You can choose from the zip file and the .exe file. If
you choose the zip BIOS file, please unzip the BIOS file onto a bootable USB device. Run
the batch file using the format FLASH.BAT filename.rom from your bootable USB device to
flash the BIOS. Then, your system will automatically reboot.
Warning: Do not shut down or reset the system while updating the BIOS to prevent possible
system boot failure!)
Note: The SPI BIOS chip used on this motherboard cannot be removed. Send your
motherboard back to our RMA Department at Supermicro for repair. For BIOS Recov-
ery instructions, please refer to the AMI BIOS Recovery Instructions posted at http://
www.supermicro.com.
70
Chapter 3: Troubleshooting
3.4 Battery Removal and Installation
Battery Removal
To remove the onboard battery, follow the steps below:
1. Power off your system and unplug your power cable.
2. Locate the onboard battery as shown below.
3. Using a tool such as a pen or a small screwdriver, push the battery lock outwards to
unlock it. Once unlocked, the battery will pop out from the holder.
4. Remove the battery.
Proper Battery Disposal
Please handle used batteries carefully. Do not damage the battery in any way; a damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
Battery Installation
1. To install an onboard battery, follow the steps 1 & 2 above and continue below:
2. Identify the battery's polarity. The positive (+) side should be facing up.
3. Insert the battery into the battery holder and push it down until you hear a click to
ensure that the battery is securely locked.
Important: When replacing a battery, be sure to only replace it with the same type.
OR
71
X11SSM(-F)/X11SSL(-F) User Manual
3.5 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before any
warranty service will be rendered. You can obtain service by calling your vendor for a
Returned Merchandise Authorization (RMA) number. When returning the motherboard to
the manufacturer, the RMA number should be prominently displayed on the outside of the
shipping carton, and the shipping package is mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service is complete.
For faster service, You can also request a RMA authorization online (http://www.supermicro.
com/RmaForm/).
This warranty only covers normal consumer use and does not cover damages incurred in
shipping or from failure due to the alternation, misuse, abuse or improper maintenance of
products.
During the warranty period, contact your distributor first for any product problems.
72
Chapter 4: BIOS
Chapter 4
BIOS
4.1 Introduction
This chapter describes the AMIBIOS™ Setup utility for the X11SSM-F motherboard. The BIOS
is stored on a chip and can be easily upgraded using a flash program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of our website for any changes to BIOS that may not be reflected in
this manual.
Starting the Setup Utility
To enter the BIOS Setup Utility, hit the <Delete> key while the system is booting-up. (In
most cases, the <Delete> key is used to invoke the BIOS setup screen. There are a few
cases when other keys are used, such as <F1>, <F2>, etc.) Each main BIOS menu option
is described in this manual.
The Main BIOS screen has two main frames. The left frame displays all the options that can
be configured. “Grayed-out” options cannot be configured. The right frame displays the key
legend. Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accompany it.
(Note that BIOS has default text messages built in. We retain the option to include, omit, or
change any of these text messages.) Settings printed in Bold are the default values.
A " " indicates a submenu. Highlighting such an item and pressing the <Enter> key will
open the list of settings within that submenu.
The BIOS setup utility uses a key-based navigation system called hot keys. Most of these
hot keys (<F1>, <F2>, <F3>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used at any time
during the setup navigation process.
73
X11SSM(-F)/X11SSL(-F) User Manual
4.2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen. You can
always return to the Main setup screen by selecting the Main tab on the top of the screen.
The Main BIOS setup screen is shown below.The following Main menu items will be displayed:
System Date/System Time
Use this option to change the system date and time. Highlight System Date or System Time
using the arrow keys. Enter new values using the keyboard. Press the <Tab> key or the arrow
keys to move between fields. The date must be entered in Day MM/DD/YYYY format. The
time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.
The date's default value is 01/01/2014 after RTC reset.
Supermicro X11SSM-F
BIOS Version
This item displays the version of the BIOS ROM used in the system.
Build Date
This item displays the date when the version of the BIOS ROM used in the system was built.
74
Chapter 4: BIOS
Memory Information
Total Memory
This item displays the total size of memory available in the system.
Memory Speed
This item displays the memory speed.
75
X11SSM(-F)/X11SSL(-F) User Manual
4.3 Advanced Setup Configurations
Use the arrow keys to select Boot Setup and press <Enter> to access the submenu items.
Warning: Take caution when changing the Advanced settings. An incorrect value, a very high
DRAM frequency, or an incorrect DRAM timing setting may make the system unstable. When
this occurs, revert to the default to the manufacture default settings.
Boot Feature
Quiet Boot
Use this feature to select the screen display between the POST messages and the OEM logo
upon bootup. Select Disabled to display the POST messages. Select Enabled to display the
OEM logo instead of the normal POST messages. The options are Enabled and Disabled.
AddOn ROM Display Mode
Use this feature to set the display mode for the Option ROM. Select Keep Current to display
the current AddOn ROM setting. Select Force BIOS to use the Option ROM display set by
the system BIOS. The options are Force BIOS and Keep Current.
Bootup NumLock State
Use this feature to set the Power-on state for the <Numlock> key. The options are Off and On.
76
Chapter 4: BIOS
Wait For 'F1' If Error
Use this feature to force the system to wait until the 'F1' key is pressed if an error occurs.
The options are Disabled and Enabled.
INT19 (Interrupt 19) Trap Response
Interrupt 19 is the software interrupt that handles the boot disk function. When this item is
set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt 19 at bootup
immediately and allow the drives that are attached to these host adaptors to function as
bootable disks. If this item is set to Postponed, the ROM BIOS of the host adaptors will not
capture Interrupt 19 immediately and allow the drives attached to these adaptors to function
as bootable devices at bootup. The options are Immediate and Postponed.
Re-try Boot
If this item is enabled, the BIOS will automatically reboot the system from a specified boot
device after its initial boot failure. The options are Disabled, Legacy Boot, and EFI Boot.
Power Configuration
Watch Dog Function
If enabled, the Watch Dog Timer will allow the system to reset or generate NMI based on
jumper settings when it is expired for more than 5 minutes. The options are Enabled and
Disabled.
Power Button Function
This feature controls how the system shuts down when the power button is pressed. Select
4_Seconds_Override for the user to power off the system after pressing and holding the power
button for 4 seconds or longer. Select Instant Off to instantly power off the system as soon
as the user presses the power button. The options are 4 Seconds Override and Instant Off.
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Stay-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off, and Last State.
77
X11SSM(-F)/X11SSL(-F) User Manual
CPU Configuration
The following CPU information will display:
• CPU Signature
• Microcode Patch
• Max CPU Speed
• Min CPU Speed
• CPU Speed
• Processor Cores
• Hyper Threading Technology
• Intel VT-x Technology
• Intel SMX Technology
• 64-bit
• EIST Technology
• CPU C3 State
• CPU C6 State
• CPU C7 State
• L1 Data Cache
• L1 Code Cache
• L2 Cache
• L3 Cache
• L4 Cache
Hyper-threading (Available when supported by the CPU)
Select Enabled to support Intel Hyper-threading Technology to enhance CPU performance.
The options are Enabled and Disabled.
78
Chapter 4: BIOS
Active Processor Cores
This feature determines how many CPU cores will be activated for each CPU. When all
is selected, all cores in the CPU will be activated. (Please refer to Intel's website for more
information.) The options are All and 1, 2, and 3.
®
Intel Virtualization Technology
Select Enable to use Intel Virtualization Technology so that I/O device assignments will be
reported directly to the VMM (Virtual Memory Management) through the DMAR ACPI Tables.
This feature offers fully-protected I/O resource-sharing across the Intel platforms, providing
the user with greater reliability, security and availability in networking and data-sharing. The
options are Enabled and Disabled.
Hardware Prefetcher (Available when supported by the CPU)
If set to Enabled, the hardware prefetcher will prefetch streams of data and instructions from
the main memory to the L2 cache to improve CPU performance. The options are Disabled
and Enabled.
Adjacent Cache Line Prefetch (Available when supported by the CPU)
The CPU prefetches the cache line for 64 bytes if this feature is set to Disabled. The CPU
prefetches both cache lines for 128 bytes as comprised if this feature is set to Enabled.
CPU AES
Select Enabled to enable Intel CPU Advanced Encryption Standard (AES) Instructions for
CPU to enhance data integrity. The options are Enabled and Disabled.
Boot Performance Mode
This feature allows the user to select the performance state that the BIOS will set before the
operating system handoff. The options are Power Saving, Max Non-Turbo Performance
and Turbo Performance.
HardWare P-States (HWP)
Use this feature to enable or disable hardware P-States support. The options are Disabled
and Enabled.
®
Intel SpeedStep™
Intel SpeedStep Technology allows the system to automatically adjust processor voltage and
core frequency to reduce power consumption and heat dissipation. The options are Disabled
and Enabled.
Turbo Mode
Select Enabled for processor cores to run faster than the frequency specified by the
manufacturer. The options are Disabled and Enabled.
79
X11SSM(-F)/X11SSL(-F) User Manual
Package Power Limit MSR Lock
Select Enabled to lock the package power limit for the model specific registers. The options
are Disabled and Enabled.
Power Limit 1 Override
Select Enabled to support average power limit (PL1) override. The default setting is Disabled.
Power Limit 2 Override
Select Enabled to support rapid power limit (PL2) override. The default setting is Enabled.
Power Limit 2
Use this item to configure the value for Power Limit 2. The value is in milli watts and the step
size is 125mW. Use the number keys on your keyboard to enter the value. Enter 0 to use the
manufacture default setting If the value is 0, the BIOS will set PL2 as 1.25* TDP.
1-Core Ratio Limit Override
This increases (multiplies) 1 clock speed in the CPU core in relation to the bus speed when
one CPU core is active. Press "+" or "-" on your keyboard to change the value. Enter 0 to
use the manufacture default setting.
2-Core Ratio Limit Override
This increases (multiplies) 2 clock speeds in the CPU core in relation to the bus speed when
two CPU cores are active. Press "+" or "-" on your keyboard to change the value. Enter 0 to
use the manufacture default setting.
3-Core Ratio Limit Override
This increases (multiplies) 3 clock speeds in the CPU core in relation to the bus speed when
three CPU cores are active. Press "+" or "-" on your keyboard to change the value. Enter 0
to use the manufacture default setting.
4-Core Ratio Limit Override
This increases (multiplies) 4 clock speeds in the CPU core in relation to the bus speed when
three CPU cores are active. Press "+" or "-" on your keyboard to change the value. Enter 0
to use the manufacture default setting.
CPU C-States
Use this feature to enable the C-State of the CPU. The options are Disabled and Enabled.
Enhanced C-States
Use this feature to enable the enhanced C-State of the CPU. The options are Disabled and
Enabled.
80
Chapter 4: BIOS
C-State Auto Demotion
Use this feature to prevent unnecessary excursions into the C-states to improve latency. The
options are Disabled, C1, C3, and C1 and C3.
C-State Un-Demotion
This feature allows the user to enable or disable the un-demotion of C-State. The options are
Disabled, C1, C3, and C1 and C3
Package C-State Demotion
Use this feature to enable or disable the Package C-State demotion. The options are Disabled
and Enabled.
Package C-State Un-Demotion
Use this feature to enable or disable the Package C-State un-demotion. The options are
Disabled and Enabled.
C-State Pre-Wake
This feature allows the user to enable or disable the C-State Pre-Wake. The options are
Disabled and Enabled.
Package C-State Limit
Use this feature to set the Package C-State limit. The options are C0/C1, C2, C3, C6, C7,
C7s, C8, and AUTO.
CPU Thermal Configuration
CPU DTS
Select Enabled for the ACPI thermal management to use the DTS SMM mechanism to
obtain CPU temperature values. Select Disabled for EC to report the CPU temperature
values. The options are Disabled and Enabled.
ACPI 3.0 T-States
Select Enabled to support CPU throttling by the operating system to reduce power
consumption. The options are Enabled and Disabled.
81
X11SSM(-F)/X11SSL(-F) User Manual
Chipset Configuration
Warning: Setting the wrong values in the following features may cause the system to malfunc-
tion.
System Agent (SA) Configuration
The following System Agent information will display:
• System Agent Bridge Name
• SA PCIe Code Version
• VT-d
VT-d
Select Enabled to enable Intel Virtualization Technology support for Direct I/O VT-d by
reporting the I/O device assignments to VMM through the DMAR ACPI Tables. This feature
offers fully-protected I/O resource-sharing across the Intel platforms, providing the user with
greater reliability, security and availability in networking and data-sharing. The options are
Enabled and Disabled.
Gaussian Mixture Model
This feature is to enable or disable the System Agent Gaussian Mixture Model device. The
opitons are Enabled and Disabled.
Graphics Configuration
Primary Display
Use this feature to select the graphics device to be used as the primary display. The options
are Auto, PEG, and PCIE.
Primary PEG
This feature allows the user to select the primary PCI Express Graphics (PEG) slot. The
options are CPU SLOT6 PCI-E 3.0 X8 (IN X16) and CPU SLOT7 PCI-E 3.0 X8.
Primary PCIE (PCI-Express Graphics)
This feature allows the user to specify which graphics card to be used as the primary
graphics card. The options are Onboard, PCH SLOT4 PCI-E 3.0 X4 (IN X8), and PCH
SLOT5 PCI-E 3.0 X4 (IN X8).
82
Chapter 4: BIOS
DMI/OPI Configuration
The following DMI information will display:
• DMI
DMI VC1 Control
Use this feature to enable or disable DMI Virtual Channel 1. The options are Enabled and
Disabled.
DMI VCm Control
Use this feature to enable or disable the DMI Virtual Channel map. The options are Enabled
and Disabled.
DMI Link ASPM Control
Use this feature to set the ASPM (Active State Power Management) state on the SA (System
Agent) side of the DMI Link. The options are Disabled and L1.
DMI Extended Sync Control
Use this feature to enable or disable the DMI extended synchronization. The options are
Enabled and Disabled.
DMI De-Emphasis Control
Use this feature to configure the De-emphasis control on DMI. The options are -6dB and
-3.5dB.
PEG Port Configuration
CPU SLOT6 PCI-E 3.0 X8 (IN X16)
SLOT6 Max Link Speed
Use this item to configure the link speed of a PCI-E port specified by the user. The options
are Auto, Gen1, Gen2, and Gen3.
SLOT6 Max Payload Size
Select Auto for the system BIOS to automatically set the maximum payload value for a PCI-E
device to enhance system performance. The options are Auto, 128 TLP, and 256 TLP.
SLOT6 Slot Power Limit Value
Use this feature to set the upper limit on the power supplied by the PCIE slot. Press "+"
or "-" on your keyboard to change this value. The default setting is 75.
SLOT6 Slot Power Limit Scale
Use this feature to select the scale used for the slot power limit value. The options are
1.0x, 0.1x, 0.01x, and 0.001x.
83
X11SSM(-F)/X11SSL(-F) User Manual
CPU SLOT7 PCI-E 3.0 X8
SLOT7 Max Link Speed
Use this item to configure the link speed of a PCI-E port specified by the user. The options
are Auto, Gen1, Gen2, and Gen3.
SLOT7 Max Payload Size
Select Auto for the system BIOS to automatically set the maximum payload value for a PCI-E
device to enhance system performance. The options are Auto, 128 TLP, and 256 TLP.
SLOT7 Slot Power Limit Value
Use this feature to set the upper limit on the power supplied by the PCIE slot. Press "+"
or "-" on your keyboard to change this value. The default setting is 75.
SLOT7 Slot Power Limit Scale
Use this feature to select the scale used for the slot power limit value. The options are
1.0x, 0.1x, 0.01x, and 0.001x.
Program PCIe ASPM After OPROM
PCIe ASPM, the Active State Power Management for PCI-Express slots, is a power
management protocol used to manage power consumption of serial-link devices installed
on PCI-Exp slots during a prolonged off-peak time. If this item is set to Enabled, PCI-E
ASMP will be programmed after OPROM. If this item is set to Disabled, the PCI-E ASPM
will be programmed before OPROM. The options are Disabled and Enabled.
Memory Configuration
The following memory information will display:
• Memory RC Version
• Memory Frequency
• Total Memory
• VDD
• DIMMA1
• DIMMA2
• DIMMB1
• DIMMB2
• Memory Timings (tCL-tRCD-tRP-tRAS)
84
Chapter 4: BIOS
Maximum Memory Frequency
Use this feature to set the maximum memory frequency for onboard memory modules. The
options are Auto, 1067, 1200, 1333, 1400, 1600, 1800, 1867, 2000, 2133, 2200, and 2400.
Max TOLUD
This feature sets the maximum TOLUD value, which specifies the "Top of Low Usable
DRAM" memory space to be used by internal graphics devices, GTT Stolen Memory, and
TSEG, respectively, if these devices are enabled. The options are Dynamic, 1 GB, 1.25
GB, 1.5 GB, 1.75 GB, 2 GB, 2.25 GB, 2.5 GB, 2.75 GB, 3 GB, 3.25 GB, and 3.5 GB.
Energy Performance Gain
Use this feature to enable or disable the energy performance gain. The options are Disabled
and Enabled.
Memory Scrambler
Select Enabled to enable memory scrambler support. The options are Disabled and
Enabled.
Fast Boot
Use this feature to enable or disable fast path through the memory reference code. The
options are Enabled and Disabled.
REFRESH_2X_MODE
Use this feature to select the refresh mode. The options are Disabled, 1-Enabled for WARM
or HOT, and 2-Enabled HOT only.
Closed Loop Thermal Management
Use this feature to monitor the power consumption and temperature of the system to predict
a thermal trend. The options are Disabled and Enabled.
PCH-IO Configuration
The following PCH-IO information will display:
• Intel PCH RC Version
• Intel PCH SKU Name
• Intel PCH Rev ID
85
X11SSM(-F)/X11SSL(-F) User Manual
PCI Express Configuration
DMI Link ASPM Control
Use this feature to set the ASPM (Active State Power Management) state on the SA (System
Agent) side of the DMI Link. The options are Disabled and Enabled.
Peer Memory Write Enable
Use this feature to enable or disable peer memory write. The options are Disabled or
Enabled.
PCH SLOT4 PCI-E 3.0 X4 (IN X8)
SLOT4 ASPM
Use this item to set the Active State Power Management (ASPM) level for a PCI-E device.
Select Auto for the system BIOS to automatically set the ASPM level based on the system
configuration. Select Disabled to disable ASPM support. The options are Disabled, L0s,
L1, L0s & L1, and Auto.
SLOT4 L1 Substates
Use this feature to configure the PCI Express L1 Substates. The options are Disabled,
L1.1, L1.2, and L1.1 & L1.2
SLOT4 PCIe Speed
Use this feature to select the PCI Express port speed. The options are Auto, Gen1, Gen2,
and Gen3.
SLOT4 Detect Non-Compliance Device
Select Enabled for the AMI BIOS to automatically detect a PCI-E device that is not compliant
with the PCI-E standards. The options are Disabled and Enabled.
PCH SLOT5 PCI-E 3.0 X4 (IN X8)
SLOT5 ASPM
Use this item to set the Active State Power Management (ASPM) level for a PCI-E device.
Select Auto for the system BIOS to automatically set the ASPM level based on the system
configuration. Select Disabled to disable ASPM support. The options are Disabled, L0s,
L1, L0s & L1, and Auto.
SLOT5 L1 Substates
Use this feature to configure the PCI Express L1 Substates. The options are Disabled,
L1.1, L1.2, and L1.1 & L1.2
86
Chapter 4: BIOS
SLOT5 PCIe Speed
Use this feature to select the PCI Express port speed. The options are Auto, Gen1, Gen2,
and Gen3.
SLOT5 Detect Non-Compliance Device
Select Enabled for the AMI BIOS to automatically detect a PCI-E device that is not compliant
with the PCI-E standards. The options are Disabled and Enabled.
Port 61h bit-4 Emulation
Select Enabled to enable the emulation of Port 61h bit-4 toggling in SMM (System Management
Mode). The options are Disabled and Enabled.
PCIe PLL SSC
Enable this feature to reduce EMI interference by down spreading clock 0.5%. Disable this
feature to centralize the clock without spreading. The options are Disabled and Enabled.
SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA
devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller(s)
This item enables or disables the onboard SATA controller supported by the Intel PCH chip.
The options are Enabled and Disabled.
SATA Mode Selection
Use this item to select the mode for the installed SATA drives. The options are AHCI and RAID.
SATA Frozen
Use this item to enable the HDD Security Frozen Mode. The options are Enabled and
Disabled.
*If the item above "SATA Mode Selection" is set to RAID, the following items will
display:
SATA RAID Option ROM/UEFI Driver
Select UEFI to load the EFI drvier for system boot. Select Legacy to load a legacy driver
for system boot. The options are Legacy ROM and UEFI Driver.
SATA Port 0 ~ Port 7 (Port 6 and Port 7 on X11SSM-F only)
This item displays the information detected on the installed SATA drive on the particular
SATA port.
• Model number of drive and capacity
• Software Preserve Support
87
X11SSM(-F)/X11SSL(-F) User Manual
Port 0 ~ Port 7 Spin Up Device (Port 6 and Port 7 on X11SSM-F only)
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device. The
options are Enabled and Disabled.
Port 0 ~ Port 7 SATA Device Type (Port 6 and Port 7 on X11SSM-F only)
Use this item to specify if the SATA port specified by the user should be connected to a Solid
State drive or a Hard Disk Drive. The options are Hard Disk Drive and Solid State Drive.
PCIe/PCI/PnP Configuration
The following information will display:
• PCI Bus Driver Version
• PCI Devices Common Settings:
PCI Latency Timer
Use this feature to set the latency Timer of each PCI device installed on a PCI bus. Select
32 to set the PCI latency to 32 PCI clock cycles. The options are 32 PCI Bus Clocks, 64
PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus
Clocks, 224 PCI Bus Clocks, and 248 PCI Bus Clocks.
PCI PERR/SERR Support
Select Enabled to allow a PCI device to generate a PERR/SERR number for a PCI Bus Signal
Error Event. The options are Enabled and Disabled.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G Address.
The options are Enabled and Disabled.
PCH SLOT4 PCI-E 3.0 X4 (IN X8) OPROM (X11SSM-F only)
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled, Legacy, and EFI.
PCH SLOT5 PCI-E 3.0 X4 (IN X8) OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled, Legacy, and EFI.
CPU SLOT6 PCI-E 3.0 X8 (IN X16) OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled, Legacy, and EFI.
88
Chapter 4: BIOS
CPU SLOT 7 PCI-E 3.0 X8 OPROM
Use this feature to select which firmware type to be loaded for the add-on card in this slot.
The options are Disabled, Legacy, and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a network device
specified by the user. The options are Legacy and EFI.
Onboard LAN1 Option ROM
Use this option to select the type of device installed in LAN Port1 used for system boot. The
default setting for LAN1 Option ROM is PXE.
Onboard LAN2 Option ROM
Use this option to select the type of device installed in LAN Port2 used for system boot. The
default setting for LAN2 Option ROM is Disabled.
Onboard Video Option ROM
Use this item to select the Onboard Video Option ROM type. The options are Disabled,
Legacy, and EFI.
VGA Priority
This feature allows the user to select the graphics adapter to be used as the primary boot
device. The options are Onboard and Offboard.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible
Firmware Interface) for network stack support. The options are Enabled and Disabled.
IPv4 PXE Support
Select Enabled to enable IPv4 PXE boot support. The options are Enabled and Disabled.
IPv6 PXE Support
Select Enabled to enable IPv6 PXE boot support. The options are Enabled and Disabled.
PXE boot wait time
Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press
"+" or "-" on your keyboard to change the value. The default setting is 0.
Media detect count
Use this option to specify the number of times media will be checked. Press "+" or "-" on your
keyboard to change the value. The default setting is 1.
89
X11SSM(-F)/X11SSL(-F) User Manual
Super IO Configuration
The following Super IO information will display:
• AMI SIO Driver Version
Super IO Chip Logical Device(s) Configuration
Serial Port 1
Serial Port 1 Configuration
This submenu allows the user the configure settings of Serial Port 1.
Serial Port 1
Select Enabled to enable the selected onboard serial port. The options are Enabled and
Disabled.
Logical Device Settings
This item displays the status of a serial part specified by the user.
Serial Port 1 Change Settings
This feature specifies the base I/O port address and the Interrupt Request address of a
serial port specified by the user. Select Auto to allow the BIOS to automatically assign the
base I/O and IRQ address.
The options for Serial Port 1 are Use Automatic Settings, (IO=3F8h; IRQ=4; DMA),
(IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;
DMA), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), and (IO=2E8h; IRQ=3, 4, 5, 6, 7,
9, 10, 11, 12; DMA).
Serial Port 2
Serial Port 2 Configuration
This submenu allows the user the configure settings of Serial Port 1.
Serial Port 2
Select Enabled to enable the selected onboard serial port. The options are Enabled and
Disabled.
Logical Device Settings
This item displays the status of a serial part specified by the user.
90
Chapter 4: BIOS
Serial Port 2 Change Settings
This feature specifies the base I/O port address and the Interrupt Request address of a serial
port specified by the user. Select Auto to allow the BIOS to automatically assign the base
I/O and IRQ address. The options for Serial Port 2 are Use Automatic Settings, (IO=2F8h;
IRQ=3; DMA), (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 6,
7, 9, 10, 11, 12; DMA), (IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA), and (IO=2E8h;
IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12; DMA).
Serial Port 2 Attribute (Available for Serial Port 2 only)
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirection.
The options are SOL and COM.
Intel Server Platform Services
The following Intel Server Platform Services information will display:
• ME BIOS Interface Version
• SPS Version
• ME FW Status Value
• ME FW State
• ME FW Operation State
• ME FW Error Code
• ME NM FW Status Value
• BIOS Booting Mode
• Cores Disabled
• ME FW SKU Information
• End-of-Post Status
Serial Port Console Redirection
COM1 Console Redirection
Select Enabled to enable console redirection support for a serial port specified by the user.
The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available for user's
configuration:
91
X11SSM(-F)/X11SSL(-F) User Manual
COM1 Console Redirection Settings
This feature allows the user to specify how the host computer will exchange data with the
client computer, which is the remote computer used by the user.
COM1 Terminal Type
This feature allows the user to select the target terminal emulation type for Console
Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color and
function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8
to use UTF8 encoding to map Unicode characters into one or more bytes. The options are
VT100, VT100+, VT-UTF8, and ANSI.
COM1 Bits Per second
Use this feature to set the transmission speed for a serial port used in Console Redirection.
Make sure that the same speed is used in the host computer and the client computer. A lower
transmission speed may be required for long and busy lines. The options are 9600, 19200,
38400, 57600 and 115200 (bits per second).
COM1 Data Bits
Use this feature to set the data transmission size for Console Redirection. The options are
7 Bits and 8 Bits.
COM1 Parity
A parity bit can be sent along with regular data bits to detect data transmission errors. Select
Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the
parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want
to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity
bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent
with your data bits. The options are None, Even, Odd, Mark, and Space.
COM1 Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data
communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
COM1 Flow Control
Use this feature to set the flow control for Console Redirection to prevent data loss caused
by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full.
Send a "Start" signal to start sending data when the receiving buffer is empty. The options
are None and Hardware RTS/CTS.
COM1 VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The
options are Disabled and Enabled.
92
Chapter 4: BIOS
COM1 Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text messages to
a remote server. The options are Disabled and Enabled.
COM1 Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and
Enabled.
COM1 Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console Redirection for
legacy OS support. The options are 80x24 and 80x25.
COM1 Putty KeyPad
This feature selects the settings for Function Keys and KeyPad used for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6,
SC0, ESCN, and VT400.
COM1 Redirection After BIOS Post
Use this feature to enable or disable legacy console redirection after BIOS POST. When set to
Bootloader, legacy console redirection is disabled before booting the OS. When set to Always
Enable, legacy console redirection remains enabled when booting the OS. The options are
Always Enable and Bootloader.
SOL/COM2
SOL/COM2 Console Redirection
Select Enabled to use the SOL port for Console Redirection. The options are Disabled and
Enabled.
*If the item above set to Enabled, the following items will become available for user's
configuration:
SOL/COM2 Console Redirection Settings
Use this feature to specify how the host computer will exchange data with the client computer,
which is the remote computer used by the user.
COM2 Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select
VT100 to use the ASCII Character set. Select VT100+ to add color and function key support.
Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding
to map Unicode characters into one or more bytes. The options are ANSI, VT100, VT100+,
and VT-UTF8.
93
X11SSM(-F)/X11SSL(-F) User Manual
COM2 Bits Per second
Use this feature to set the transmission speed for a serial port used in Console Redirection.
Make sure that the same speed is used in the host computer and the client computer. A lower
transmission speed may be required for long and busy lines. The options are 9600, 19200,
38400, 57600 and 115200 (bits per second).
COM2 Data Bits
Use this feature to set the data transmission size for Console Redirection. The options are
7 Bits and 8 Bits.
COM2 Parity
A parity bit can be sent along with regular data bits to detect data transmission errors. Select
Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the
parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want
to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity
bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent
with your data bits. The options are None, Even, Odd, Mark and Space.
COM2 Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data
communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
COM2 Flow Control
Use this feature to set the flow control for Console Redirection to prevent data loss caused
by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full.
Send a "Start" signal to start sending data when the receiving buffer is empty. The options
are None and Hardware RTS/CTS.
COM2 VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100 terminals. The
options are Disabled and Enabled.
COM2 Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text messages to
a remote server. The options are Disabled and Enabled.
COM2 Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and
Enabled.
COM2 Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console Redirection for
legacy OS support. The options are 80x24 and 80x25.
94
Chapter 4: BIOS
COM2 Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a terminal emulator
designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SCO, ESCN, and
VT400.
COM2 Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS POST. When
set to Bootloader, legacy Console Redirection is disabled before booting the OS. When set
to Always Enable, legacy Console Redirection remains enabled when booting the OS. The
options are Always Enable and Bootloader.
EMS (Emergency Management Services) Console Redirection
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The
options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available for user's
configuration:
EMS Console Redirection Settings
This feature allows the user to specify how the host computer will exchange data with the
client computer, which is the remote computer used by the user.
Out-of-Band Management Port
The feature selects a serial port in a client server to be used by the Microsoft Windows
Emergency Management Services (EMS) to communicate with a remote host server. The
options are COM1 and SOL/COM2.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select
VT100 to use the ASCII character set. Select VT100+ to add color and function key support.
Select ANSI to use the extended ASCII character set. Select VT-UTF8 to use UTF8 encoding
to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-
UTF8, and ANSI.
Bits Per Second
This item sets the transmission speed for a serial port used in Console Redirection. Make
sure that the same speed is used in the host computer and the client computer. A lower
transmission speed may be required for long and busy lines. The options are 9600, 19200,
57600, and 115200 (bits per second).
95
X11SSM(-F)/X11SSL(-F) User Manual
Flow Control
Use this item to set the flow control for Console Redirection to prevent data loss caused by
buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full.
Send a "Start" signal to start sending data when the receiving buffer is empty. The options
are None, Hardware RTS/CTS, and Software Xon/Xoff.
Data Bits
Use this feature to set the data transmission size for Console Redirection. The options are
7 Bits and 8 Bits.
Parity
A parity bit can be sent along with regular data bits to detect data transmission errors. Select
Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the
parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want
to send a parity bit with your data bits in transmission. Select Mark to add a mark as a parity
bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent
with your data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data
communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.
ACPI Settings
High Precision Event Timer
Select Enabled to activate the High Performance Event Timer (HPET) that produces periodic
interrupts at a much higher frequency than a Real-time Clock (RTC) does in synchronizing
multimedia streams, providing smooth playback and reducing the dependency on other
timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU.
The High Performance Event Timer is used to replace the 8254 Programmable Interval Timer.
The options are Disabled and Enabled.
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and
provide a common infrastructure for the system to handle hardware errors within the Windows
OS environment to reduce system crashes and to enhance system recovery and health
monitoring. The options are Disabled and Enabled.
96
Chapter 4: BIOS
Trusted Computing Configuration
Security Device Support
If this feature and the TPM jumper on the motherboard are both set to Enabled, onbaord
security devices will be enabled for TPM (Trusted Platform Module) support to enhance data
integrity and network security. Please reboot the system for a change on this setting to take
effect. The options are Disabled and Enabled.
TPM State
This feature changes the TPM State. The options are Disabled and Enabled. Note: The
system will restart to change the TPM State.
Pending TPM operation
Use this item to schedule a TPM-related operation to be performed by a security device for
system data integrity. Your system will reboot to carry out a pending TPM operation. The
options are None and TPM Clear.
Device Select
Use this feature to select the TPM version. TPM 1.2 will restrict support to TPM 1.2 devices.
TPM 2.0 will restrict support for TPM 2.0 devices. Select Auto to enable support for both
versions. The default setting is Auto.
The following are informational status messages that indicate the current TPM State:
TPM Enabled Status
TPM Active Status
TPM Owner Status
TXT Support
Intel TXT (Trusted Execution Technology) helps protect against software-based attacks and
ensures protection, confidentiality and integrity of data stored or created on the system. Use
this feature to enable or disable TXT Support. The options are Disabled and Enabled.
97
X11SSM(-F)/X11SSL(-F) User Manual
iSCSi Configuration
iSCSI Initiator Name
This feature allows the user to enter the unique name of the iSCSI Initiator in IQN format.
Once the name of the iSCSI Initiator is entered into the system, configure the proper settings
for the following items.
Add an Attempt
Delete Attempts
Change Attempt order
Intel I210 Gigabit Network Connection - OC:C4:7A:1A:44:CE
NIC Configuration
Link Speed
This feature allows the user to specify the port speed used for the selected boot protocol.
The options are Auto Negotiated, 10 Mbps Half, 10 Mbps Full, 100 Mbps Half, and 100
Mbps Full.
Wake On LAN
Select Enabled for Wake_On_LAN support, which will allow the system to "wake up" when
an onboard device receives an incoming signal. The options are Disabled and Enabled.
Blink LEDs
Use this feature to identify the physical network port by blinking the associated LED. Use the
keybaord to select a value.
UEFI Driver
This item displays the UEFI driver version.
Adapter PBA
This item displays the Processor Bus Adapter (PBA) model number. The PBA number is a
nine digit number (i.e., 010B00-000) located near the serial number.
Device Name
This item displays the adapter device name.
Chip Type
This item displays the network adapter chipset name.
98
Chapter 4: BIOS
PCI Device ID
This item displays the device ID number.
PCI Address
This item displays the PCI address for this computer. PCI addresses are 3 two-digit
hexadecimal numbers.
Link Status
This item displays the connection status.
MAC Address
This item displays the MAC address for this computer. Mac addresses are 6 two-digit
hexadecimal numbers.
Virtual MAC Address
This item displays the Virtual MAC address for this computer. Mac addresses are 6 two-digit
hexadecimal numbers.
Intel I210 Gigabit Network Connection - OC:C4:7A:1A:44:CF
NIC Configuration
Link Speed
This feature allows the user to specify the port speed used for the selected boot protocol.
The options are Auto Negotiated, 10 Mbps Half, 10 Mbps Full, 100 Mbps Half, and 100
Mbps Full.
Wake On LAN
Select Enabled for Wake_On_LAN support, which will allow the system to "wake up" when
an onboard device receives an incoming signal. The options are Disabled and Enabled.
Blink LEDs
Use this feature to identify the physical network port by blinking the associated LED. Use the
keybaord to select a value.
UEFI Driver
This item displays the UEFI driver version.
Adapter PBA
This item displays the Processor Bus Adapter (PBA) model number. The PBA number is a
nine digit number (i.e., 010B00-000) located near the serial number.
99
X11SSM(-F)/X11SSL(-F) User Manual
Device Name
This item displays the adapter device name.
Chip Type
This item displays the network adapter chipset name.
PCI Device ID
This item displays the device ID number.
PCI Address
This item displays the PCI address for this computer. PCI addresses are 3 two-digit
hexadecimal numbers.
Link Status
This item displays the connection status.
MAC Address
This item displays the MAC address for this computer. Mac addresses are 6 two-digit
hexadecimal numbers.
Virtual MAC Address
This item displays the Virtual MAC address for this computer. Mac addresses are 6 two-digit
hexadecimal numbers.
100
Chapter 4: BIOS
4.4 Event Logs
Use this feature to configure Event Log settings.
Change SMBIOS Event Log Settings
Enabling/Disabling Options
SMBIOS Event Log
Change this item to enable or disable all features of the SMBIOS Event Logging during system
boot. The options are Enabled and Disabled.
Erasing Settings
Erase Event Log
If No is selected, data stored in the event log will not be erased. Select Yes, Next Reset, data
in the event log will be erased upon next system reboot. Select Yes, Every Reset, data in
the event log will be erased upon every system reboot. The options are No, Yes, Next reset,
and Yes, Every reset.
When Log is Full
Select Erase Immediately for all messages to be automatically erased from the event log
when the event log memory is full. The options are Do Nothing and Erase Immediately.
101
X11SSM(-F)/X11SSL(-F) User Manual
SMBIOS Event Long Standard Settings
Log System Boot Event
This option toggles the System Boot Event logging to enabled or disabled. The options are
Disabled and Enabled.
MECI
The Multiple Event Count Increment (MECI) counter counts the number of occurences that
a duplicate event must happen before the MECI counter is incremented. This is a numeric
value. The default value is 1.
METW
The Multiple Event Time Window (METW) defines number of minutes must pass between
duplicate log events before MECI is incremented. This is in minutes, from 0 to 99. The default
value is 60.
Note: After making changes on a setting, be sure to reboot the system for the changes
to take effect.
View SMBIOS Event Log
This section displays the contents of the SMBIOS Event Log.
102
Chapter 4: BIOS
4.5 IPMI
Use this feature to configure Intelligent Platform Management Interface (IPMI) settings.
BMC Firmware Revision
This item indicates the IPMI firmware revision used in your system.
IPMI Status (Baseboard Management Controller)
This item indicates the status of the IPMI firmware installed in your system.
System Event Log
Enabling/Disabling Options
SEL Components
Select Enabled for all system event logging at bootup. The options are Enabled and Disabled.
Erasing Settings
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot. Select
Yes, On every reset to erase all system event logs upon each system reboot. Select No to
keep all system event logs after each system reboot. The options are No, Yes, On next reset,
and Yes, On every reset.
103
X11SSM(-F)/X11SSL(-F) User Manual
When SEL is Full
This feature allows the user to decide what the BIOS should do when the system event log
is full. Select Erase Immediately to erase all events in the log when the system event log is
full. The options are Do Nothing and Erase Immediately.
Note: After making changes on a setting, be sure to reboot the system for the changes
to take effect.
BMC Network Configuration
BMC Network Configuration
IPMI LAN Selection
This item displays the IPMI LAN setting. The default setting is Failover.
IPMI Network Link Status
This item displays the IPMI Network Link status. The default setting is Dedicated LAN.
Update IPMI LAN Configuration
Select Yes for the BIOS to implement all IP/MAC address changes at the next system boot.
The options are No and Yes.
*If the item above set to Yes, the following item will become available for user's
configuration:
Configuration Address Source
This feature allows the user to select the source of the IP address for this computer. If Static
is selected, you will need to know the IP address of this computer and enter it to the system
manually in the field. If DHCP is selected, the BIOS will search for a DHCP (Dynamic Host
Configuration Protocol) server in the network that is attached to and request the next available
IP address for this computer. The options are DHCP and Static.
Configuration Address Source
This item displays the current configuration address for this computer.
Station IP Address
This item displays the Station IP address for this computer. This should be in decimal and in
dotted quad form (i.e., 192.168.10.253).
Subnet Mask
This item displays the sub-network that this computer belongs to. The value of each three-
digit number separated by dots should not exceed 255.
104
Chapter 4: BIOS
Station MAC Address
This item displays the Station MAC address for this computer. Mac addresses are 6 two-digit
hexadecimal numbers.
Gateway IP Address
This item displays the Gateway IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 172.31.0.1).
105
X11SSM(-F)/X11SSL(-F) User Manual
4.6 Security
This menu allows the user to configure the following security settings for the system.
Password Check
Select Setup for the system to check for a password at Setup. Select Always for the system
to check for a password at bootup or upon entering the BIOS Setup utility. The options are
Setup and Always.
Administrator Password
Press Enter to create a new, or change an existing Administrator password.
Secure Boot Menu
This section displays the contents of the following secure boot features:
• System Mode
• Secure Boot
• Vendor Keys
Secure Boot
Use this item to enable secure boot. The options are Disabled and Enabled.
106
Chapter 4: BIOS
Secure Boot Mode
Use this item to select the secure boot mode. The options are Standard and Custom.
CSM Support
Select Enabled to support the EFI Compatibility Support Module (CSM), which provides
compatibility support for traditional legacy BIOS for system boot. The options are Enabled
and Disabled.
Key Management
This submenu allows the user to configure the following Key Management settings.
Provision Factory Default Keys
Select Enabled to install the default Secure-Boot keys set by the manufacturer. The options
are Disabled and Enabled.
Enroll All Factory Default Keys
Select Yes to install all default secure keys set by the manufacturer. The options are Yes
and No.
Save All Secure Boot Variables
This feature allows the user to decide if all secure boot variables should be saved.
Platform Key (PK)
This feature allows the user to configure the settings of the platform keys.
Set New Key
Select Yes to load the new platform keys (PK) from the manufacturer's defaults. Select No
to load the platform keys from a file. The options are Yes and No.
Key Exchange Key
Set New Key
Select Yes to load the KEK from the manufacturer's defaults. Select No to load the KEK from
a file. The options are Yes and No.
Append Key
Select Yes to add the KEK from the manufacturer's defaults list to the existing KEK. Select
No to load the KEK from a file. The options are Yes and No.
Authorized Signatures
Set New Key
Select Yes to load the database from the manufacturer's defaults. Select No to load the DB
from a file. The options are Yes and No.
107
X11SSM(-F)/X11SSL(-F) User Manual
Append Key
Select Yes to add the database from the manufacturer's defaults to the existing DB. Select
No to load the DB from a file. The options are Yes and No.
Forbiden Signatures
Set New Key
Select Yes to load the DBX from the manufacturer's defaults. Select No to load the DBX from
a file. The options are Yes and No.
Append Key
Select Yes to add the DBX from the manufacturer's defaults to the existing DBX. Select No
to load the DBX from a file. The options are Yes and No.
Authorized TimeStamps
Set New Key
Select Yes to load the DBT from the manufacturer's defaults. Select No to load the DBT from
a file. The options are Yes and No.
Append Key
Select Yes to add the DBT from the manufacturer's defaults list to the existing DBT. Select
No to load the DBT from a file. The options are Yes and No.
108
Chapter 4: BIOS
4.7 Boot
Use this feature to configure Boot Settings:
Boot Mode Select
Use this item to select the type of device that the system is going to boot from. The options
are Legacy, UEFI, and Dual. The default setting is Dual.
Fixed Boot Order Priorities
This option prioritizes the order of bootable devices that the system to boot from. Press
<Enter> on each entry from top to bottom to select devices.
*If the item above set to Legacy, UEFI/Dual the following items will be displayed:
• Legacy/UEFI/Dual/Boot Order #1
• Legacy/UEFI/Dual/Boot Order #2
• Legacy/UEFI/Dual/Boot Order #3
• Legacy/UEFI/Dual/Boot Order #4
• Legacy/UEFI/Dual/Boot Order #5
• Legacy/UEFI/Dual/Boot Order #6
• Legacy/UEFI/Dual/Boot Order #7
109
X11SSM(-F)/X11SSL(-F) User Manual
• Legacy/UEFI/Dual/Boot Order #8
• Legacy/UEFI/Dual/Boot Order #9
• Legacy/UEFI/Dual/Boot Order #10
• Legacy/UEFI/Dual/Boot Order #11
• Legacy/UEFI/Dual/Boot Order #12
• Legacy/UEFI/Dual/Boot Order #13
• Legacy/UEFI/Dual/Boot Order #14
• Legacy/UEFI/Dual/Boot Order #15
Delete Boot Option
Use this feature to remove a pre-defined boot device from which the system will boot during
startup.
The settings are [any pre-defined boot device].
Hard Disk Drive BBS Priorities (Available when SATA HDD is connected onboard)
This feature allows the user to specify which hard disk drives are boot devices.
• Legacy Boot Order #1
NETWORK Drive BBS Priorities
This feature allows the user to specify which UEFI network drive devices are boot devices.
• Legacy Boot Order #1
• Legacy Boot Order #2
UEFI Application Boot Priorities
This feature allows the user to specify which UEFI devices are boot devices.
• UEFI Boot Order #1
110
Chapter 4: BIOS
4.8 Save & Exit
Select the Exit tab from the BIOS setup utility screen to enter the Exit BIOS Setup screen.
Discard Changes and Exit
Select this option to quit the BIOS Setup without making any permanent changes to the
system configuration, and reboot the computer. Select Discard Changes and Exit from the
Exit menu and press <Enter>.
Save Changes and Reset
When you have completed the system configuration changes, select this option to leave the
BIOS setup utility and reboot the computer, so the new system configuration parameters can
take effect. Select Save Changes and Exit from the Exit menu and press <Enter>.
Save Changes
After completing the system configuration changes, select this option to save the changes
you have made. This will not reset (reboot) the system.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the AMI BIOS
utility Program.
111
X11SSM(-F)/X11SSL(-F) User Manual
Default Options
Restore Optimized Defaults
To set this feature, select Restore Optimized Defaults from the Save & Exit menu and press
<Enter>. These are factory settings designed for maximum system stability, but not for
maximum performance.
Save As User Defaults
To set this feature, select Save as User Defaults from the Exit menu and press <Enter>. This
enables the user to save any changes to the BIOS setup for future use.
Restore User Defaults
To set this feature, select Restore User Defaults from the Exit menu and press <Enter>. Use
this feature to retrieve user-defined settings that were saved previously.
Boot Override
Listed on this section are other boot options for the system (i.e., Built-in EFI shell). Select
an option and press <Enter>. Your system will boot to the selected boot option.
112
Appendix A: BIOS Codes
Appendix A
BIOS Codes
BIOS Error POST (Beep) Codes
During the POST (Power-On Self-Test) routines, which are performed upon each system
boot, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue to boot. These
error messages normally appear on the screen.
Fatal errors will not allow the system to continue with bootup. If a fatal error occurs, you
should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps. The numbers
on the fatal error list correspond to the number of beeps for the corresponding error.
BIOS Beep (POST) Codes
Beep Code
Error Message
Description
1 beep
Refresh
Ready to boot
5 short, 1 long
Memory error
No memory detected in system
Con-in includes USB or PS/2 keyboard, PCI or serial
console redirection, and IPMI KVM or SOL.
5 beeps
No con-in or con-out devices
Refresh
Con-out includes the video controller, PCI or serial
console redirection, and IPMI SOL
1 beep per device
1 beep for each USB device detected
IPMI Error Codes
Beep Code
Error Message
Description
1 long continuous
System OH
System overheat condition
113
X11SSM(-F)/X11SSL(-F) User Manual
Appendix B
Software Installation
B.1 Installing Software Programs
The Supermicro website contains drivers and utilities for your system at https://www.
supermicro.com/wftp/driver. Some of these must be installed, such as the chipset driver.
After accessing the website, go into the CDR_Images (in the parent directory of the above
link) and locate the ISO file for your motherboard. Download this file to create a DVD of the
drivers and utilities it contains. (You may also use a utility to extract the ISO file if preferred.)
After creating a DVD with the ISO files, insert the disk into the DVD drive on your system
and the display shown in Figure B-1 should appear.
Another option is to go to the Supermicro website at http://www.supermicro.com/products/.
Find the product page for your motherboard here, where you may download individual drivers
and utilities to your hard drive or a USB flash drive and install from there.
Note: To install the Windows OS, please refer to the instructions posted on our website
at http://www.supermicro.com/support/manuals/.
Figure B-1. Driver/Tool Installation Display Screen
114
Appendix B: Software Installation
Click the icons showing a hand writing on paper to view the readme files for each item. Click
the computer icons to the right of these items to install each item (from top to bottom) one at
a time. After installing each item, you must re-boot the system before moving on to the
next item on the list. The bottom icon with a CD on it allows you to view the entire contents.
B.2 SuperDoctor® 5
The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based
interface for Windows and Linux operating systems. The program monitors such system health
information as CPU temperature, system voltages, system power consumption, fan speed,
and provides alerts via email or Simple Network Management Protocol (SNMP).
SuperDoctor 5 comes in local and remote management versions and can be used with Nagios
to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM
Server), you can remotely control power on/off and reset chassis intrusion for multiple systems
with SuperDoctor 5 or IPMI. SuperDoctor 5 Management Server monitors HTTP, FTP, and
SMTP services to optimize the efficiency of your operation.
Note: The default User Name and Password for SuperDoctor 5 is admin / admin.
Figure B-2. SuperDoctor 5 Interface Display Screen (Health Information)
Note: The SuperDoctor 5 program and user’s manual can be downloaded from the
Supermicro website at http://www.supermicro.com/products/nfo/sms_sd5.cfm.
115
X11SSM(-F)/X11SSL(-F) User Manual
Appendix C
Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of
situations which have the potential for bodily injury. Should you have questions or experience
difficulty, contact Supermicro's Technical Support department for assistance. Only certified
technicians should attempt to install or configure components.
Read this section in its entirety before installing or configuring components.
These warnings may also be found on our website at http://www.supermicro.com/about/
policies/safety_information.cfm.
Battery Handling
Warning! There is the danger of explosion if the battery is replaced incorrectly. Replace
the battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推
奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电
池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按
照製造商的說明指示處理廢棄舊電池。
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur
durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten
Batterien nach den Anweisungen des Herstellers.
116
Appendix C: Warning Statements
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une
pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées
conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la
batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante.
Desechar las baterías gastadas según las instrucciones del fabricante.
!
אזהרה
ף
להחלי
יש
.תקינה
לא
בדרך
והוחלפה
במידה
הסוללה
של
פיצוץ
סכנת
קיימת
.
מומלצת
יצרן
מחברת
התואם
בסוג
הסוללה
את
.
היצרן
הוראות
לפי
לבצע
יש
המשומשות
הסוללות
סילוק
ꢋꢉꢌ
فع
ة
ꢈꢉꢈص
ر
ꢉغ
قة
ꢇطر
ꢊ ة
ꢇꢄبطا
ꢂꢁ ل
ꢁسحبذ
ꢁ ة
ꢂا
ꢃ في
ꢄجا
ꢅꢆꢁ ꢀم
خطر
هناك
ة
ꢇꢄبطا
ꢂꢁ ل
ꢁسحبذ
ꢁ ة
نع
ꢓꢑꢂꢁ ة
ꢒشر
ꢂꢁ ꢔꢊ أوصث
ا
ꢑꢒ ا
ꢐꢂعاد
ꢇ ما
أو
ꢎنى
ꢂꢁ ꢏꢅن
ꢊ ꢍفق
ة
ع
ꢆا
ꢓꢂꢁ ة
ꢒشر
ꢂꢁ ات
ꢑꢉꢌحع
ꢂ وفقا
ة
ꢌꢑحع
ꢘꢑꢂꢁ ات
ꢇꢄبطا
ꢂꢁ ꢀم
ꢕꢌꢖꢗ 경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나
제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라
사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de batterij
slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte
batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden.
117
X11SSM(-F)/X11SSL(-F) User Manual
Product Disposal
Warning! Ultimate disposal of this product should be handled according to all national
laws and regulations.
製品の廃棄
この製品を廃棄処分する場合、国 の関係する全ての法律・条例に従い処理する必要があります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos
nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou
directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
ר
המוצ
סילוק
!
אזהרה
.
המדינה
וחוקי
להנחיות
בהתאם
להיות
חייב
זה
מוצר
של
סופי
סילוק
ة
ꢉلىطن
ꢀ ئح
ꢀى
ꢁل
ꢀو
ꢂꢉꢋꢀلقى
ꢀ ꢈꢉꢃꢊل
وفقا
ꢅمع
ꢆلتعام
ꢀ نبغي
ꢇ نتج
ꢃل
ꢀ ꢀذ
ꢄ ꢂم
لنهائي
ꢀ ص
ꢁلتخ
ꢀ ند
ꢌ 경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
118
Appendix D: UEFI BIOS Recovery
Appendix D
UEFI BIOS Recovery
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing
the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro
be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS
update. If you need to update the BIOS, do not shut down or reset the system while the BIOS
is updating to avoid possible boot failure.
D.1 Overview
The Unified Extensible Firmware Interface (UEFI) provides a software-based interface
between the operating system and the platform firmware in the pre-boot environment. The
UEFI specification supports an architecture-independent mechanism that will allow the UEFI
OS loader stored in an add-on card to boot the system. The UEFI offers clean, hands-off
management to a computer during system boot.
D.2 Recovering the UEFI BIOS Image
A UEFI BIOS flash chip consists of a recovery BIOS block and a main BIOS block (a main
BIOS image). The recovery block contains critical BIOS codes, including memory detection
and recovery codes for the user to flash a healthy BIOS image if the original main BIOS image
is corrupted. When the system power is turned on, the recovery block codes execute first.
Once this process is complete, the main BIOS code will continue with system initialization
and the remaining POST (Power-On Self-Test) routines.
Note 1: Follow the BIOS recovery instructions below for BIOS recovery when the main
BIOS block crashes.
Note 2: When the BIOS recovery block crashes, you will need to follow the procedures
to make a Returned Merchandise Authorization (RMA) request. (For a RMA request,
please see section 3.5 for more information). Also, you may use the Supermicro Up-
date Manager (SUM) Out-of-Band (OOB) (https://www.supermicro.com.tw/products/
nfo/SMS_SUM.cfm) to reflash the BIOS.
D.3 Recovering the Main BIOS Block with a USB Device
This feature allows the user to recover the main BIOS image using a USB-attached device
without additional utilities used. A USB flash device such as a USB Flash Drive, or a USB
CD/DVD ROM/RW device can be used for this purpose. However, a USB Hard Disk drive
cannot be used for BIOS recovery at this time.
119
X11SSM(-F)/X11SSL(-F) User Manual
The file system supported by the recovery block is FAT (including FAT12, FAT16, and FAT32),
which is installed on a bootable or non-bootable USB-attached device. However, the BIOS
might need several minutes to locate the SUPER.ROM file if the media size becomes too
large due to the huge volumes of folders and files stored in the device.
To perform UEFI BIOS recovery using a USB-attached device, follow the instructions below:
1. Using a different machine, copy the "Super.ROM" binary image file into the Root "\"
directory of a USB device or a writable CD/DVD.
Note 1: If you cannot locate the "Super.ROM" file in your drive disk, visit our website
at www.supermicro.com to download the BIOS package. Extract the BIOS binary
image into a USB flash device and rename it "Super.ROM" for BIOS recovery use.
Note 2: Before recovering the main BIOS image, confirm that the "Super.ROM" bi-
nary image file you download is the same version or a close version meant for your
motherboard.
2. Insert the USB device that contains the new BIOS image ("Super.ROM") into your USB
drive and reset the system until the following screen appears:
Note: On the other hand, if the following screen displays, please load the "Super.
ROM" file to the root folder and connect this folder to the system. (You can do so by
inserting a USB device that contains the new "Super.ROM" image to your machine
for BIOS recovery.)
120
Appendix D: UEFI BIOS Recovery
3. After locating the healthy BIOS binary image, the system will enter the BIOS Recovery
menu as shown below:
Note: At this point, you may decide if you want to start the BIOS recovery. If you decide
to proceed with BIOS recovery, follow the procedures below.
4. When the screen as shown above displays, use the arrow keys to select the item
"Proceed with flash update" and press the <Enter> key. You will see the BIOS recovery
progress as shown in the screen below:
Note: Do not interrupt the BIOS flashing process until it has completed.
121
X11SSM(-F)/X11SSL(-F) User Manual
5. After the BIOS recovery process is complete, press any key to reboot the system.
6. Using a different system, extract the BIOS package into a bootable USB flash drive.
7. When a DOS prompt appears, enter FLASH.BAT BIOSname.### at the prompt.
Note: Do not interrupt this process until the BIOS flashing is complete.
8. After seeing the message indicating the BIOS update has completed, unplug the AC
power cable from the power supply, clear CMOS, then plug the AC power cable in the
power supply again to power on the system.
9. Press <Del> continuously to enter the BIOS Setup utility.
10. Press <F3> to load the default settings.
11. After loading the default settings, press <F4> to save the settings and exit the BIOS
Setup utility.
122
Appendix E: Dual Boot Block
Appendix E
Dual Boot Block
E.1 Introduction
This motherboard supports the Dual Boot Block feature, which is the last-ditch mechanism
to recover the BIOS boot block. This section provides an introduction to the feature.
BIOS Boot Block
A BIOS boot block is the minimum BIOS loader required to enable necessary hardware
components for the BIOS crisis recovery flash that will update the main BIOS block. An on-
call BIOS boot-block corruption may occur due to a software tool issue (see image below)
or an unexpected power outage during BIOS updates.
-----------------------------------------------------------------------------------------------------------------
AMI Firmware Update Utility vX.XX.XX
Copyright (C)XXXX American Megatrends Inc. All Rights Reserved.
-----------------------------------------------------------------------------------------------------------------
Reading flash . . . . . . . . . . . . . . . . . . . . . . done
-- ME Data Size checking . ok
-- FFS checksums . . . . . . . . ok
Erasing Boot Block . . . . . . . . . . . done
__Updating Boot Block . . . . . . . . 0x00A91000 (13%)
BIOS Boot Block Corruption Occurrence
When a BIOS boot block is corrupted due to an unexpected power outage or a software tool
malfunctioning during BIOS updates, you can still reboot the system by closing pins 2 and 3
using a cap on jumper JBR1. When JBR1 is set to pins 2 and 3, the system will boot from a
backup boot block pre-loaded in the BIOS by the manufacturer.
123
X11SSM(-F)/X11SSL(-F) User Manual
E.2 Steps to Reboot the System by Using Jumper JBR1
1. Power down the system.
2. Close pins 2-3 on jumper JBR1, and power on the system.
3. Follow the BIOS recovery SOP listed in the previous chapter (Appendix D).
4. After completing the steps above, power down the system.
5. Close pins 1-2 on jumper JBR1, and power on the system.
124
相关型号：
X11SSM-F
X11SSM(-F)/X11SSL(-F) User ManualWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
X1202S8-2.7
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, SOIC-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202S8-2.7A
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, SOIC-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202S8-2.7AT1
Real Time Clock, 0 Timer(s), CMOS, PDSO8, PLASTIC, SOIC-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202S8-4.5A
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, SOIC-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202S8I-4.5A
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, SOIC-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202V8
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202V8-2.7
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202V8-4.5A
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1202V8I-2.7
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDSO8, PLASTIC, TSSOP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1203P
Real Time Clock, Volatile, 0 Timer(s), CMOS, PDIP8, PLASTIC, DIP-8Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
XICOR
X1203S8
IC-SMD-RTC WITH EEPROMWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
©2020 ICPDF网 联系我们和版权申明