X9410WP24M [ETC]
Digital Potentiometer ; 数字电位计\n
| 型号： | X9410WP24M |
| 厂家： | 
ETC |
| 描述： | Digital Potentiometer
|
| 文件： | 总19页 (文件大小：159K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
APPLICATION NOTES
A V A I L A B L E
AN99 • AN115 • AN120 • AN124 • AN133 • AN134 • AN135
Low Noise/Low Power/2-Wire Bus
X9418
Dual Digitally Controlled Potentiometers (XDCP™)
FEATURES
DESCRIPTION
• Two potentiometers in one package
• 2-wire serial interface
• Register oriented format
—Direct Read/Write Wiper Position
—Store as many as Four Positions per
Potentiometer
The X9418 integrates two digitally controlled
potentiometers (XDCP) on a monolithic CMOS
integrated microcircuit.
The digitally controlled potentiometer is implemented
using 63 resistive elements in a series array. Between
each element are tap points connected to the wiper
terminal through switches. The position of the wiper on
the array is controlled by the user through the 2-wire
bus interface. Each potentiometer has associated with
it a volatile Wiper Counter Register (WCR) and 4
nonvolatile Data Registers (DR0:DR3) that can be
directly written to and read by the user. The contents
of the WCR controls the position of the wiper on the
resistor array through the switches. Power up recalls
the contents of DR0 to the WCR.
• Power supplies
—V
= 2.7V to 5.5V
CC
—V+ = 2.7V to 5.5V
—V– = –2.7V to –5.5V
• Low power CMOS
—Standby current < 1µA
—Ideal for Battery Operated Applications
• High reliability
—Endurance–100,000 Data Changes per Bit per
Register
—Register Data Retention–100 years
• 8-bytes of nonvolatile memory
• 10KΩ resistor array
• Resolution: 64 taps each potentiometer
• 24-pin plastic DIP, 24-lead TSSOP and 24-lead
SOIC packages
The XDCP can be used as a three-terminal
potentiometer or as a two-terminal variable resistor in
a wide variety of applications including control,
parameter adjustments, and signal processing.
BLOCK DIAGRAM
V
V
V+
V-
CC
SS
R0 R1
R2 R3
V
/R
H0 H0
Wiper
Counter
Register
(WCR)
V
V
/R
L0 L0
WP
/R
SCL
W0 W0
SDA
A0
A1
Interface
and
Control
8
Circuitry
A2
V
/R
A3
W1 W1
Data
R0 R1
R2 R3
V
/R
Wiper
Counter
Register
(WCR)
H1 H1
Resistor
Array
XDCP1
V
/R
L1 L1
Characteristics subject to change without notice. 1 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
PIN DESCRIPTIONS
Host Interface Pins
Serial Clock (SCL)
PIN CONFIGURATION
DIP/SOIC
V+
V
1
24
23
22
21
20
19
18
17
16
5
CC
NC
NC
NC
A0
NC
A3
SCL
NC
NC
R
/V
/V
2
3
L0 L0
The SCL input is used to clock data into and out of the
X9418.
R
H0 H0
/V
R
4
5
W0 W0
A2
Serial Data (SDA)
WP
6
X9418
SDA
7
SDA is a bidirectional pin used to transfer data into
and out of the device. It is an open drain output and
may be wire-ORed with any number of open drain or
open collector outputs. An open drain output requires
the use of a pull-up resistor. For selecting typical
values, refer to the guidelines for calculating typical
values on the bus pull-up resistors graph.
A1
8
R
/V
9
L1 L1
R
/V
10
H1 H1
NC
V-
R
/V
11
12
14
13
W1 W1
V
SS
TSSOP
Device Address (A –A )
0
3
WP
A2
V
SDA
A1
1
2
3
24
23
22
21
20
19
18
17
16
15
14
13
The Address inputs are used to set the least
significant 4 bits of the 8-bit slave address. A match in
the slave address serial data stream must be made
with the Address input in order to initiate
communication with the X9418. A maximum of 16
devices may occupy the 2-wire serial bus.
/R
R
/V
W0 W0
L1 L1
V
V
V
/R
4
5
R
/V
H0 H0
H1 H1
/R
R
/V
L0 L0
W1 W1
V
6
7
CC
SS
X9418
NC
NC
NC
V+
A0
NC
NC
NC
8
9
Potentiometer Pins
10
V-
SCL
A3
11
12
V /R (V /R —V /R ), V /R (V /R —V /R )
H
H
H0 H0
H1 H1
L
L
L0 L0
L1 L1
NC
The V /R and V /R inputs are equivalent to the
H
H
L
L
terminal connections on either end of a mechanical
potentiometer.
PIN NAMES
Symbol
V /R (V /R —V /R )
W1 W1
W
W
W0 W0
Description
The wiper outputs are equivalent to the wiper output of
a mechanical potentiometer.
SCL
Serial Clock
Serial Data
SDA
A0-A3
Hardware Write Protect Input (WP)
Device Address
The WP pin when low prevents nonvolatile writes to
the Data Registers.
V
V
/R –V /R
,
Potentiometer Pins
(terminal equivalent)
H0 H0 H1 H1
/R –V /R
L0 L0 L1 L1
V
/R –V /R
Potentiometer Pins
(wiper equivalent)
W0 W0 W1 W1
Analog Supplies V+, V-
The Analog Supplies V+, V- are the supply voltages
for the XDCP analog section.
WP
Hardware Write Protection
Analog Supplies
V+,V-
V
V
System Supply Voltage
System Ground
CC
SS
NC
No Connection
Characteristics subject to change without notice. 2 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
PRINCIPLES OF OPERATION
The X9418 will respond with an acknowledge after
recognition of a start condition and its slave address
and once again after successful receipt of the
command byte. If the command is followed by a data
byte the X9418 will respond with a final acknowledge.
The X9418 is
a
highly integrated microcircuit
incorporating two resistor arrays and their associated
registers and counters and the serial interface logic
providing direct communication between the host and
the XDCP potentiometers.
Array Description
The X9418 is comprised of two resistor arrays. Each
array contains 63 discrete resistive segments that are
connected in series. The physical ends of each array
are equivalent to the fixed terminals of a mechanical
Serial Interface
The X9418 supports a bidirectional bus oriented
protocol. The protocol defines any device that sends
data onto the bus as a transmitter and the receiving
device as the receiver. The device controlling the
transfer is a master and the device being controlled is
the slave. The master will always initiate data transfers
and provide the clock for both transmit and receive
operations. Therefore, the X9418 will be considered a
slave device in all applications.
potentiometer (V /R and V /R inputs).
H
H
L
L
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper
(V /R ) output. Within each individual array only one
W
W
switch may be turned on at a time. These switches are
controlled by the Wiper Counter Register (WCR). The
six bits of the WCR are decoded to select, and enable,
one of sixty-four switches.
Clock and Data Conventions
Data states on the SDA line can change only during
The WCR may be written directly, or it can be changed
by transferring the contents of one of four associated
Data Registers into the WCR. These Data Registers
and the WCR can be read and written by the host
system.
SCL LOW periods (t
). SDA state changes during
LOW
SCL HIGH are reserved for indicating start and stop
conditions.
Start Condition
All commands to the X9418 are preceded by the start
condition, which is a HIGH to LOW transition of SDA
Device Addressing
Following a start condition the master must output the
address of the slave it is accessing. The most
significant four bits of the slave address are the device
type identifier (refer to Figure 1 below). For the X9418
this is fixed as 0101[B].
while SCL is HIGH (t
). The X9418 continuously
HIGH
monitors the SDA and SCL lines for the start condition
and will not respond to any command until this
condition is met.
Stop Condition
Figure 1. Slave Address
All communications must be terminated by a stop
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH.
Device Type
Identifier
Acknowledge
0
1
0
1
A3
A2
A1
A0
Acknowledge is a software convention used to provide
a positive handshake between the master and slave
devices on the bus to indicate the successful receipt of
data. The transmitting device, either the master or the
slave, will release the SDA bus after transmitting eight
bits. The master generates a ninth clock cycle and
during this period the receiver pulls the SDA line LOW
to acknowledge that it successfully received the eight
bits of data.
Device Address
The next four bits of the slave address are the device
address. The physical device address is defined by the
state of the A –A inputs. The X9418 compares the
serial data stream with the address input state; a
successful compare of all four address bits is required
for the X9418 to respond with an acknowledge. The
0
3
A –A inputs can be actively driven by CMOS input
0
3
signals or tied to V or V
.
CC
SS
Characteristics subject to change without notice. 3 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Acknowledge Polling
point to one of the two pots and when applicable they
point to one of four associated registers. The format is
shown below in Figure 2.
The disabling of the inputs, during the internal
nonvolatile write operation, can be used to take
advantage of the typical 5ms EEPROM write cycle
time. Once the stop condition is issued to indicate the
end of the nonvolatile write command the X9418
initiates the internal write cycle. ACK polling can be
initiated immediately. This involves issuing the start
condition followed by the device slave address. If the
X9418 is still busy with the write operation no ACK will
be returned. If the X9418 has completed the write
operation an ACK will be returned, and the master can
then proceed with the next operation.
Figure 2. Instruction Byte Format
Register
Select
I3
I2
I1
I0
R1 R0
0
P0
Wiper Counter
Register Select
Instructions
Flow 1. ACK Polling Sequence
The four high order bits define the instruction. The next
two bits (R1 and R0) select one of the four registers
that is to be acted upon when a register oriented
instruction is issued. The last bits (P0) select which
one of the two potentiometers is to be affected by the
instruction. Bit 1 is defined to be 0.
Nonvolatile Write
Command Completed
Enter ACK Polling
Four of the nine instructions end with the transmission
of the instruction byte. The basic sequence is
illustrated in Figure 3. These two-byte instructions
exchange data between the wiper counter register and
one of the data registers. A transfer from a Data
Register to a Wiper Counter Register is essentially a
write to a static RAM. The response of the wiper to this
Issue
START
Issue Slave
Issue STOP
Address
action will be delayed t
counter register (current wiper position), to a Data
Register is a write to nonvolatile memory and takes a
. A transfer from the wiper
WRL
ACK
Returned?
NO
minimum of t
to complete. The transfer can occur
YES
WR
between one of the two potentiometers and one of its
associated registers; or it may occur globally, wherein
the transfer occurs between both of the potentiometers
and one of their associated registers.
NO
Further
Operation?
YES
Four instructions require a three-byte sequence to
complete. These instructions transfer data between the
host and the X9418; either between the host and one
of the Data Registers or directly between the host and
the wiper counter register. These instructions are:
Read Wiper Counter Register (read the current wiper
position of the selected pot), write Wiper Counter
Register (change current wiper position of the selected
pot), read Data Register (read the contents of the
selected nonvolatile register) and write Data Register
(write a new value to the selected Data Register). The
sequence of operations is shown in Figure 4.
Issue
Instruction
Issue STOP
Proceed
Proceed
Instruction Structure
The next byte sent to the X9418 contains the instruction
and register pointer information. The four most
significant bits are the instruction. The next four bits
Characteristics subject to change without notice. 4 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Figure 3. Two-Byte Instruction Sequence
SCL
SDA
S
T
A
R
T
0
1
0
1
A3 A2 A1 A0
A
C
K
I3 I2
I1 I0 R1 R0
0
P0
A
C
K
S
T
O
P
The Increment/Decrement command is different from
the other commands. Once the command is issued and
the X9418 has responded with an acknowledge, the
master can clock the selected wiper up and/or down in
one segment steps; thereby, providing a fine tuning
resistor segment towards the V /R terminal. Similarly,
H H
for each SCL clock pulse while SDA is LOW, the
selected wiper will move one resistor segment towards
the V /R terminal. A detailed illustration of the
L
L
sequence and timing for this operation are shown in
capability to the host. For each SCL clock pulse (t
)
Figures 5 and 6 respectively.
HIGH
while SDA is HIGH, the selected wiper will move one
Table 1. Instruction Set
Instruction Set
Instruction
I
I
I
I
R
R
P
P
Operation
1/0 Read the contents of the Wiper Counter Register
pointed to by P
3
2
1
0
1
0
1
0
Read Wiper Counter
Register
1
1
1
1
1
0
0
0
1
1
0
1
1
0
0
1
0
1
0
1
0
0
0
0
Write Wiper Counter
Register
0
0
0
0
0
0
1/0 Write new value to the Wiper Counter Register
pointed to by P
0
Read Data Register
1/0 1/0
1/0 1/0
1/0 1/0
1/0 Read the contents of the Data Register pointed to
by P and R –R
0
1
0
Write Data Register
1/0 Write new value to the Data Register pointed to by
P and R –R
0
1
0
XFR Data Register to
Wiper Counter Register
1/0 Transfer the contents of the Data Register pointed
to by P and R –R to its associated Wiper Counter
0
1
0
Register
XFR Wiper Counter
Register to Data Register
1
0
1
0
1
0
0
0
1
0
0
1
0
1
0
0
1/0 1/0
1/0 1/0
1/0 1/0
0
0
0
0
1/0 Transfer the contents of the Wiper Counter Register
pointed to by P to the Data Register pointed to by
0
R –R
1
0
Global XFR Data
Registers to Wiper
Counter Registers
0
0
Transfer the contents of the Data Registers pointed
to by R –R of both pots to their respective Wiper
Counter Registers
1
0
Global XFR Wiper
Counter Registers to
Data Register
Transfer the contents of both Wiper Counter
Registers to their respective data Registers pointed
to by R –R of both pots
1
0
Increment/Decrement
Wiper Counter Register
0
0
1/0 Enable Increment/decrement of the Wiper Counter
Register pointed to by P
0
Note: (7) 1/0 = data is one or zero
Characteristics subject to change without notice. 5 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Figure 4. Three-Byte Instruction Sequence
SCL
SDA
S
T
A
R
T
0
1
0
1
A3 A2 A1 A0
A
C
K
I3 I2
I1 I0 R1 R0 0 P0
A
C
K
0
0
D5 D4 D3 D2 D1 D0
A
C
K
S
T
O
P
Figure 5. Increment/Decrement Instruction Sequence
SCL
SDA
X
X
S
T
A
R
T
0
1
0
1
A3 A2 A1 A0
A
C
K
I3 I2
I1 I0 R1 R0
0
P0
A
C
K
I
I
D
E
C
1
S
T
O
P
I
D
N
C
1
N
C
2
N
C
n
E
C
n
Figure 6. Increment/Decrement Timing Limits
INC/DEC
CMD
Issued
t
WRID
SCL
SDA
Voltage Out
V
/R
W
W
Characteristics subject to change without notice. 6 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Figure 7. Acknowledge Response from Receiver
SCL from
1
Master
8
9
Data Output
from Transmitter
Data Output
from Receiver
START
Acknowledge
Figure 8. Detailed Potentiometer Block Diagram
Serial Data Path
Serial
Bus
Input
V /R
H H
From Interface
Circuitry
C
o
u
n
t
Register 0
Register 2
Register 1
8
6
Parallel
Bus
Input
e
r
Wiper
D
e
c
o
d
e
Register 3
Counter
Register
(WCR)
INC/DEC
Logic
If WCR = 00[H] then V /R = V /R
W
W
L
L
UP/DN
UP/DN
If WCR = 3F[H] then V /R = V /R
H
W
W
H
V /R
Modified SCL
L
L
CLK
V
/R
W
W
Characteristics subject to change without notice. 7 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
DETAILED OPERATION
Register Descriptions
Both XDCP potentiometers share the serial interface
and share a common architecture. Each potentiometer
has a Wiper Counter Register and four Data Registers.
A detailed discussion of the register organization and
array operation follows.
Data Registers, (6-Bit), Nonvolatile
D5
NV
D4
NV
D3
NV
D2
NV
D1
NV
D0
NV
(MSB)
(LSB)
Wiper Counter Register
Four 6-bit Data Registers for each XDCP. (eight 6-bit
registers in total).
The X9418 contains two wiper counter registers, one
for each XDCP potentiometer. The Wiper Counter
Register can be envisioned as a 6-bit parallel and
serial load counter with its outputs decoded to select
one of sixty-four switches along its resistor array. The
contents of the WCR can be altered in four ways: it
may be written directly by the host via the write Wiper
Counter Register instruction (serial load); it may be
written indirectly by transferring the contents of one of
four associated Data Registers via the XFR Data
Register instruction (parallel load); it can be modified
one step at a time by the Increment/Decrement
instruction. Finally, it is loaded with the contents of its
Data Register zero (DR0) upon power-up.
– {D5~D0}: These bits are for general purpose not
volatile data storage or for storage of up to four
different wiper values.The contents of Data Register
0 are automatically moved to the Wiper Counter
Register on power-up.
Wiper Counter Register, (6-Bit), Volatile
WP5
V
WP4
V
WP3
V
WP2
V
WP1
V
WP0
V
(MSB)
(LSB)
One 6-bit wiper counter register for each XDCP. (Four
6-bit registers in total.)
The WCR is a volatile register; that is, its contents are
lost when the X9418 is powered-down. Although the
register is automatically loaded with the value in DR0
upon power-up, it should be noted this may be
different from the value present at power-down.
– {D5~D0}:These bits specify the wiper position of the
respective XDCP. The Wiper Counter Register is
loaded on power-up by the value in Data Register 0.
The contents of the WCR can be loaded from any of
the other Data Register or directly. The contents of
the WCR can be saved in a DR.
Data Registers
Each potentiometer has four nonvolatile Data
Registers. These can be read or written directly by the
host and data can be transferred between any of the
four Data Registers and the Wiper Counter Register. It
should be noted all operations changing data in one of
these registers is a nonvolatile operation and will take
a maximum of 10ms.
If the application does not require storage of multiple
settings for the potentiometer, these registers can be
used as regular memory locations that could possibly
store system parameters or user preference data.
Characteristics subject to change without notice. 8 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Instruction Format
Notes: (1) “MACK”/”SACK”: stands for the acknowledge sent by the master/slave.
(2) “A3 ~ A0”: stands for the device addresses sent by the master.
(3) “X”: indicates that it is a “0” for testing purpose but physically it is a “don’t care” condition.
(4) “I”: stands for the increment operation, SDA held high during active SCL phase (high).
(5) “D”: stands for the decrement operation, SDA held low during active SCL phase (high).
Read Wiper Counter Register (WCR)
S device type
device
addresses
instruction
opcode
wiper
addresses
wiper position
(sent by slave on SDA)
S
A
C
K
S
A
C
K
M S
A T
C O
K P
T
A
R
T
identifier
W W W W W W
0 0 P P P P P P
A A A A
P
0
0
1
0
1
1
0
0
1
0
0
0
3
2 1 0
5
4 3 2 1 0
Write Wiper Counter Register (WCR)
S device type
device
addresses
instruction
opcode
wiper
addresses
wiper position
(sent by master on SDA)
S
A
C
K
S
A
C
K
S S
A T
C O
K P
T
A
R
T
identifier
W W W W W W
0 0 P P P P P P
A A A A
P
0
0
1
0
1
1
0
1
0
0
0
0
3
2 1 0
5
4 3 2 1 0
Read Data Register (DR)
S device type device
instruction
opcode
wiper
addresses
wiper position/data
(sent by slave on SDA)
S
A
C
K
S
A
C
K
M S
A T
C O
K P
T
A
R
T
identifier
addresses
W W W W W W
0 0 P P P P P P
A A A A
R R
P
0
0
1
0
1
1
0
1
1
0
3
2
1
0
1
0
5
4 3 2 1 0
Write Data Register (DR)
S device type
device
addresses
instruction
opcode
wiper
addresses
wiper position/data
(sent by master on SDA)
S
S
A
C
K
S S
T
A
R
T
identifier
A
C
K
A T HIGH-VOLTAGE
C O WRITE CYCLE
K P
W W W W W W
0 0 P P P P P P
5 4 3 2 1 0
A A A A
3 2 1 0
R R
1 0
P
0
0 1 0 1
1 1 0 0
0
XFR Data Register (DR) to Wiper Counter Register (WCR)
S device type
device
addresses
instruction
opcode
wiper
addresses
S
A
C
K
S S
A T
C O
K P
T
A
R
T
identifier
A A A A
3 2 1 0
R R
1 0
P
0
0 1 0 1
1 1 0 1
0
Characteristics subject to change without notice. 9 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
XFR Wiper Counter Register (WCR) to Data Register (DR)
S device type
device
addresses
instruction
opcode
wiper
addresses
S
A
C
K
S S
T
A
R
T
identifier
A T HIGH-VOLTAGE
C O WRITE CYCLE
K P
A A A A
3 2 1 0
R R
1 0
P
0
0 1 0 1
1 1 1 0
0
Increment/Decrement Wiper Counter Register (WCR)
S
T
A
R
T
device type
identifier
device
addresses
instruction
opcode
wiper
addresses
increment/decrement
(sent by master on SDA)
S
A
C
K
S
A
C
K
S
T
O
P
A A A A
P
0
I/ I/
D D
I/ I/
D D
0
1
0
1
0
0
1
0
0
0
0
.
.
.
.
3
2 1 0
Global XFR Data Register (DR) to Wiper Counter Register (WCR)
S
T
A
R
T
device type
identifier
device
addresses
instruction
opcode
wiper
addresses
S
A
C
K
S S
A T
C O
K P
A A A A
R R
1 0
0
1
0
1
0
0
0
1
0 0
3
2
1
0
Global XFR Wiper Counter Register (WCR) to Data Register (DR)
S device type
device
addresses
instruction
opcode
wiper
addresses
S
A
C
K
S S
A T
C O
K P
T
A
R
T
identifier
HIGH-VOLTAGE
WRITE CYCLE
A A A A
3 2 1 0
R R
0 0
1 0
0 1 0 1
1 0 0 0
SYMBOL TABLE
Guidelines for Calculating Typical Values of Bus
Pull-Up Resistors
WAVEFORM
INPUTS
OUTPUTS
120
V
CC MAX
OL MIN
R
=
=1.8KΩ
MIN
I
Must be
steady
Will be
steady
100
80
t
R
R
=
MAX
C
BUS
May change
from Low to
High
Will change
from Low to
High
Max.
Resistance
60
40
20
0
May change
from High to
Low
Will change
from High to
Low
Min.
Resistance
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
0
20 40 60 80 100 120
N/A
Center Line
is High
Impedance
Bus Capacitance (pF)
Characteristics subject to change without notice. 10 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias....................–65°C to +135°C
Storage temperature.........................–65°C to +150°C
Voltage on SDA, SCL or any address
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
input with respect to V ......................... –1V to +7V
SS
Voltage on V+ (referenced to V ) ........................ 10V
SS
Voltage on V- (referenced to V ) ........................ -10V
SS
(V+) – (V-) ............................................................. 12V
Any V /R .............................................................. V+
H
H
Any V /R ................................................................ V-
L
L
Lead temperature (soldering, 10 seconds) ........300°C
I
(10 seconds) ............................................... ±12mA
W
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
Max.
+70°C
+85°C
Device
X9418
Supply Voltage (V ) Limits
CC
5V ±10%
–40°C
X9418-2.7
2.7V to 5.5V
ANALOG CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
R
Parameter
End to end resistance
Power rating
Min.
Typ.
Max.
±20
50
Unit
%
Test Conditions
TOTAL
mW
mA
Ω
25°C, each pot
I
Wiper current
±6
W
R
Wiper resistance
150
40
250
100
+5.5
+5.5
-4.5
-2.7
V+
Wiper current = ± 1mA, V = 3V
CC
W
Ω
Wiper current = ± 1mA, V = 3V
CC
V+
V-
Voltage on V+ pin
Voltage on V- pin
X9418
+4.5
+2.7
-5.5
-5.5
V-
V
X9418-2.7
X9418
V
X9418-2.7
V
Voltage on any V /R or V /R pin
V
dBV
%
TERM
H
H
L
L
Noise
Resolution (4)
-140
1.6
Ref: 1kHz
Absolute linearity (1)
Relative linearity (2)
±1
MI(3)
MI(3)
ppm/°C
V
—V
w(n)(actual)
w(n)(expected)
]
±0.2
V
—[V
w(n) + MI
w(n + 1)
Temperature Coefficient of R
±300
TOTAL
Ratiometric Temperature Coefficient
Potentiometer Capacitances
±20 ppm/°C
pF
C /C /C
W
10/10/25
See Circuit #3,
Spice Macromodel
H
L
Characteristics subject to change without notice. 11 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Typ.
Max.
Unit
Test Conditions
I
V
supply current
1
mA
f = 400kHz, SDA = Open,
SCL
CC1
CC
(nonvolatile write)
Other Inputs = V
SS
I
V
supply current
100
µA
f
= 400kHz, SDA = Open,
SCL
CC2
CC
(move wiper, write, read)
Other Inputs = V
SS
I
V
current (standby)
1
µA
µA
µA
V
SCL = SDA = V , Addr. = V
CC SS
SB
CC
I
Input leakage current
Output leakage current
Input HIGH voltage
Input LOW voltage
Output LOW voltage
10
10
V
V
= V to V
SS CC
LI
IN
I
= V to V
SS CC
LO
OUT
V
V
x 0.7
V
V
x 0.5
IH
CC
CC
V
–0.5
x 0.1
V
IL
CC
V
0.4
V
I
= 3mA
OL
OL
Notes: (1) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used
as a potentiometer.
(2) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potenti-
ometer. It is a measure of the error in step size.
(3) MI = RTOT/63 or (V —V )/63, single pot
H
L
(4) Max. = all four arrays cascaded together, Typical = individual array resolutions.
ENDURANCE AND DATA RETENTION
Parameter
Minimum endurance
Data retention
Min.
100,000
100
Unit
Data changes per bit per register
Years
CAPACITANCE
Symbol
Test
Max.
Unit
pF
Test Conditions
(5)
I/O
C
Input/output capacitance (SDA)
8
6
V
= 0V
= 0V
I/O
(5)
IN
C
Input capacitance (A0, A1, A2, A3, and SCL)
pF
V
IN
POWER-UP TIMING
Symbol
Parameter
Min.
Typ.
Max.
1
Unit
(6)
PUR
t
Power-up to initiation of read operation
Power-up to initiation of write operation
ms
ms
(6)
PUW
t
5
t V
V Power up ramp rate
CC
0.2
50
V/msec
R
CC
POWER-UP AND POWER-DOWN
There are no restrictions on the power-up or power-down sequencing of the bias supplies V , V+, and V- provided
CC
that all three supplies reach their final values within 1msec of each other. However, at all times, the voltages on the
potentiometer pins must be less than V+ and more than V–. The recall of the wiper position from nonvolatile
memory is not in effect until all supplies reach their final value.
Notes: (5) This parameter is periodically sampled and not 100% tested
(6) t
and t
are the delays required from the time the third (last) power supply (V , V+ or V-) is stable until the specific
PUR
PUW CC
instruction can be issued.These parameters are periodically sampled and not 100% tested.
Characteristics subject to change without notice. 12 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
A.C. TEST CONDITIONS
Circuit #3 SPICE Macro Model
Input pulse levels
V
x 0.1 to V x 0.9
CC
CC
R
TOTAL
Input rise and fall times
Input and output timing level
10ns
R
R
L
H
C
V
x 0.5
L
CC
C
H
C
W
10pF
EQUIVALENT A.C. LOAD CIRCUIT
10pF
25pF
5V
2.7V
R
W
1533Ω
SDA Output
100pF
100pF
AC TIMING (over recommended operating conditions)
Symbol Parameter
Min.
Max.
Unit
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
f
Clock frequency
400
SCL
t
Clock cycle time
2500
600
1300
600
600
600
100
30
CYC
t
Clock high time
HIGH
t
Clock low time
LOW
t
Start setup time
SU:STA
HD:STA
SU:STO
t
Start hold time
t
Stop setup time
t
SDA data input setup time
SDA data input hold time
SCL and SDA rise time
SCL and SDA fall time
SU:DAT
t
HD:DAT
t
300
300
900
R
t
F
t
SCL low to SDA data output valid time
SDA data output hold time
100
50
AA
t
DH
T
Noise suppression time constant at SCL and SDA inputs
Bus free time (prior to any transmission)
WP, A0, A1, A2 and A3 setup time
50
I
t
1300
0
BUF
t
SU:WPA
t
WP, A0, A1, A2 and A3 hold time
0
HD:WPA
Characteristics subject to change without notice. 13 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
HIGH-VOLTAGE WRITE CYCLE TIMING
Symbol
Parameter
Typ.
Max.
Unit
t
High-voltage write cycle time (store instructions)
5
10
ms
WR
XDCP TIMING
Symbol
Parameter
Min. Max. Unit
t
Wiper response time after the third (last) power supply is stable
Wiper response time after instruction issued (all load instructions)
10
10
10
µs
µs
µs
WRPO
t
WRL
t
Wiper response time from an active SCL/SCK edge (increment/decrement instruction)
WRID
Note: (8) A device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the undefined region of the falling
edge of SCL.
TIMING DIAGRAMS
START and STOP Timing
g
(START)
(STOP)
t
t
F
R
SCL
SDA
t
t
t
SU:STO
SU:STA
HD:STA
t
t
F
R
Input Timing
t
t
CYC
HIGH
SCL
SDA
t
LOW
t
t
t
BUF
SU:DAT
HD:DAT
Output Timing
SCL
SDA
t
t
DH
AA
Characteristics subject to change without notice. 14 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
XDCP Timing (for All Load Instructions)
(STOP)
SCL
SDA
LSB
t
WRL
V
/R
W
W
XDCP Timing (for Increment/Decrement Instruction)
SCL
Wiper Register Address
Inc/Dec
Inc/Dec
SDA
t
WRID
V
/R
W
W
Write Protect and Device Address Pins Timing
(START)
(STOP)
SCL
...
(Any Instruction)
...
SDA
...
t
t
SU:WPA
HD:WPA
WP
A0, A1
A2, A3
Characteristics subject to change without notice. 15 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
PACKAGING INFORMATION
24-Lead Plastic Dual In-Line Package Type P
1.265 (32.13)
1.230 (31.24)
0.557 (14.15)
0.530 (13.46)
Pin 1 Index
Pin 1
0.080 (2.03)
0.065 (1.65)
1.100 (27.94)
Ref.
0.162 (4.11)
0.140 (3.56)
Seating
Plane
0.030 (0.76)
0.015 (0.38)
0.150 (3.81)
0.125 (3.18)
0.110 (2.79)
0.090 (2.29)
0.065 (1.65)
0.040 (1.02)
0.022 (0.56)
0.014 (0.36)
0.625 (15.87)
0.600 (15.24)
0°
Typ. 0.010 (0.25)
15°
NOTE:
1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
Characteristics subject to change without notice. 16 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
PACKAGING INFORMATION
24-Lead Plastic Small Outline Gull Wing Package Type S
0.393 (10.00)
0.290 (7.37)
0.299 (7.60)
0.420 (10.65)
Pin 1 Index
Pin 1
0.014 (0.35)
0.020 (0.50)
0.598 (15.20)
0.610 (15.49)
(4X) 7°
0.092 (2.35)
0.105 (2.65)
0.003 (0.10)
0.012 (0.30)
0.050 (1.27)
0.050"Typical
0.010 (0.25)
0.020 (0.50)
X 45°
0.050"
Typical
0° – 8°
0.009 (0.22)
0.013 (0.33)
0.420"
0.015 (0.40)
0.050 (1.27)
0.030" Typical
24 Places
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 17 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
PACKAGING INFORMATION
24-Lead Plastic, TSSOP Package Type V
.026 (.65) BSC
.169 (4.3)
.177 (4.5)
.252 (6.4) BSC
.303 (7.70)
.311 (7.90)
.047 (1.20)
.0075 (.19)
.0118 (.30)
.002 (.06)
.005 (.15)
.010 (.25)
Gage Plane
(7.72)
(4.16)
0°–8°
Seating Plane
.020 (.50)
.030 (.75)
(1.78)
(0.42)
Detail A (20X)
(0.65)
ALL MEASUREMENTS ARE TYPICAL
.031 (.80)
.041 (1.05)
See Detail “A”
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
Characteristics subject to change without notice. 18 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
X9418
Ordering Information
X9418
Y
P
T
V
V
Limits
CC
Device
Blank = 5V ±10%
–2.7 = 2.7 to 5.5V
Temperature Range
Blank = Commercial = 0°C to +70°C
I = Industrial = –40°C to +85°C
Package
P24 = 24-Lead Plastic DIP
S24 = 24-Lead SOIC
V24 = 24-Lead TSSOP
Potentiometer Organization
Pot 0 Pot 1
W =
10KΩ 10KΩ
©Xicor, Inc. 2000 Patents Pending
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty,
express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement.
Xicor, Inc. makes no warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices
at any time and without notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, or licenses are implied.
TRADEMARK DISCLAIMER:
Xicor and the Xicor logo are registered trademarks of Xicor, Inc. AutoStore, Direct Write, Block Lock, SerialFlash, MPS, and XDCP are also trademarks of Xicor, Inc. All
others belong to their respective owners.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846;
4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691;
5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection
and correction, redundancy and back-up features to prevent such an occurrence.
Xicor’s products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
Characteristics subject to change without notice. 19 of 19
REV 1.1 10/6/00
www.xicor.com
This Material Copyrighted by Its Respective Manufacturer
相关型号：
X9410WS24-2.7T1
DUAL 10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, PLASTIC, SOIC-24
RENESAS
X9410WS24I-2.7T1
DUAL 10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, PLASTIC, SOIC-24
RENESAS
X9410WS24IT1
DUAL 10K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO24, 0.300 INCH, PLASTIC, MS-013AD, SOIC-24
RENESAS
©2020 ICPDF网 联系我们和版权申明