333/R5C1-ATWB-L/MS [EVERLIGHT]

Visible LED,;


型号：	333/R5C1-ATWB-L/MS
厂家：	EVERLIGHT ELECTRONICS CO., LTD
描述：	Visible LED,
文件：	总9页 (文件大小：294K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Lamp

PRELIMINARY

333/R5C1-ATWB-L/MS

Features

˙Popular T-1 3/4 round package.

˙High efficiency.

˙General purpose leads.

˙Selected minimum intensities.

˙The product itself will remain within RoHS compliant version.

˙UV resistant epoxy

Descriptions

˙The series is specially designed for applications

requiring higher brightness.

˙The LED lamps are available with different

colors, intensities, epoxy colors, etc.

Applications

˙Color Graphic Signs

˙Message boards

˙Variable message signs (VMS)

˙Commercial outdoor advertising

www.everlight.com

Ver.:1 Release Date:08/27/2013

狀態:Developing(開發階段)

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Device Selection Guide

Chip Materials

AlGaInP

Emitted Color

Resin Color

Water clear

Brilliant Red

Absolute Maximum Ratings (Ta=25℃)

Parameter

Symbol

Rating

Unit

Reverse Voltage

V_R

I_F

Forward Current

Peak Forward Current

(Duty 1/10 @1KHz)

Power Dissipation

160

I_FP

120

T_opr

℃

-40 ~ +85

-40 ~ +100

2000

Operating Temperature

Storage Temperature

Tstg

℃

ESD

ESD_HBM

Soldering Temperature

T_sol

260 ℃ for 5 sec.

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Electro-Optical Characteristics (Ta=25℃)

Parameter

Luminous Intensity

Symbol

Min.

Typ.

Max.

Unit

Condition

2θ_1/2

λp

7150

11250

18000

mcd

deg

I_F=20mA

V_R=5V

Viewing Angle

632

624

Peak Wavelength

λd

620

628

Dominant Wavelength

Spectrum Radiation Bandwidth

Forward Voltage

Δλ

1.8

2.0

2.6

V_F

I_R

μA

Reverse Current

Bin Range of Luminous Intensity

Bin Code

Min.

Max.

Unit

mcd

Condition

I_F=20mA

7150

9000

11250

14250

9000

11250

14250

18000

Note:

Tolerance of Luminous Intensity: ±10%

Bin Range of Dominant Wavelength

Bin Code

Min.

Max.

Unit

Condition

I_F=20mA

620

624

628

Note:

Tolerance of Dominant Wavelength: ±1nm

Bin Range of Forward Voltage

Bin Code

Min.

Max.

Unit

Condition

I_F=20mA

1.8

2.0

2.2

2.4

2.0

2.2

2.4

2.6

Note:

Tolerance of Forward Voltage: ±0.1V

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Typical Electro-Optical Characteristics Curves

Relative Intensity vs. Wavelength (Ta=25℃)

Directivity (Ta=25℃)

1.0

0.8

0.6

0.4

0.2

0.0

450

500

550

600

650

700

Wavelength (nm)

Relative Intensity (a.u.)

Forward Current vs. Forward Voltage (Ta=25℃)

Relative Intensity vs. Forward Current (Ta=25℃)

2.5

2.0

1.5

1.0

0.5

0.0

1.0

1.5

2.0

2.5

3.0

3.5

Forward Voltage (V)

Forward Current (mA)

Relative Intensity vs. Ambient Temp.

Forward Current vs. Ambient Temp.

2.0

1.5

1.0

0.5

0.0

100

Ambient Temperature Ta(℃)

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Package Dimension

Note:

Other dimensions are in millimeters, tolerance is 0.25mm except being specified.

˙Protruded resin under flange is 1.5mm Max LED.

Release Date:08/27/2013

狀態:Developing(開發階段)

ꢀ

www.everlight.com

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Moisture Resistant Packing Materials

Label Explanation

‧CPN: Customer’s Product Number

‧P/N: Product Number

‧QTY: Packing Quantity

‧CAT: Ranks of Luminous Intensity and Forward Voltage

‧HUE: Rank of Dominant Wavelength

‧REF: Reference

‧LOT No: Lot Number

Packing Specification

■ Anti-electrostatic bag

■ Inner Carton

■ Outside Carton

Label

EL ECTROSTATIC ELECTRONAGNETIC

MAGNETIC OR RADIOACTIVE RELDS

anti-static for 750

■

Packing Quantity

1. Min 200pcs to Max 500 PCS/1 Bag, 5 Bags/1 Inner Carton.

2. 10 Inner Cartons/1 Outside Carton

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

Production Designation

3 3 3 / R 5 C 1 - □ □ □ □

Voltage Group

Luminous Intensity Bins

Wave Group

Viewing Angle

Color Lens

Color

Product name

Notes

1. Lead Forming



During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.

Lead forming should be done before soldering.

Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it

may break the LEDs.



Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs.

When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the

LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.

2. Storage



The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life

limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a

nitrogen atmosphere and moisture absorbent material.



Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can

occur.

3. Soldering



Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,

and soldering beyond the base of the tie bar is recommended.

Recommended soldering conditions:



Hand Soldering

DIP Soldering

100 ℃ Max. (60 sec

300℃ Max. (30W

Max.)

Temp. at tip of iron

Preheat temp.

Bath temp. & time

Max.)

Soldering time

Distance

3 sec Max.

3mm Min.(From solder Distance

joint to epoxy bulb)

260 Max., 5 sec Max

3mm Min. (From solder

joint to epoxy bulb)



Recommended soldering profile

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

laminar wave

Fluxing

Prehead



Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.

Dip and hand soldering should not be done more than one time

After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return

to room temperature.



A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.

Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the lowest

possible temperature is desirable for the LEDs.



Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the

solder wave.

4. Cleaning



When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than

one minute. Dry at room temperature before use.



Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the

LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be

pre-qualified to ensure this will not cause damage to the LED

5. Heat Management



Heat management of LEDs must be taken into consideration during the design stage of LED application. The current

should be de-rated appropriately by referring to the de-rating curve found in each product specification.



The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating

curve.

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

DATASHEET

Lamp

333/R5C1-ATWB-L/MS

6. ESD (Electrostatic Discharge)



The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.

When handling the products, the following measures against electrostatic discharge are strongly

recommended:

Eliminating the charge

Grounded wrist strap, ESD footwear, clothes, and floors

Grounded workstation equipment and tools

ESD table/shelf mat made of conductive materials



Proper grounding is required for all devices, equipment, and machinery used in product assembly.

Surge protection should be considered when designing of commercial products.

If tools or equipment contain insulating materials such as glass or plastic,

the following measures against electrostatic discharge are strongly recommended:

Dissipating static charge with conductive materials

Preventing charge generation with moisture

Neutralizing the charge with ionizers.

7. Directions for use



The LEDs should be operated with forward bias. The driving circuit must be designed so that the LEDs are not

subjected to forward or reverse voltage while it is off. If reverse voltage is continuously applied to the LEDs, it may

cause migration resulting in LED damage.

8. Other



Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above

specification.



When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these

specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which

does not comply

with the absolute maximum ratings and the instructions included in these specification sheets.

These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t



reproduce or cause anyone to reproduce them without EVERLIGHT’s consent

狀態:Developing(開發階段)

Release Date:08/27/2013

www.everlight.com

ꢀ

333/R5C1-ATWB-L/MS [EVERLIGHT]

相关型号：

333/R5C1-ATWB/MS

333/R5C1-ATWB/P/MS

333/Y2C0-AUYB

333/Y2C1-ASWB

333/Y5C1-APQB/MS

333/Y5C1-APQB/P/MS

333/Y5C1-ARUB/MS

333/Y5C1-ATWB/MS

3330-0-00-80-00-00-03-0

3330-1-00-15-00-00-03-0

3330-1-00-80-00-00-03-0

3330-2-00-15-00-00-03-0