334-15-T2C1-7UWC [EVERLIGHT]
Popular T-1 3/4 round package; 流行的T-1 3/4圆包型号: | 334-15-T2C1-7UWC |
厂家: | EVERLIGHT ELECTRONICS CO., LTD |
描述: | Popular T-1 3/4 round package |
文件: | 总12页 (文件大小:241K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Technical Data Sheet
334-15/T2C1-7UWC
Features
․Popular T-1 3/4 round package.
․High luminous power.
․Typical chromaticity coordinates x=0.30, y=0.29
according to CIE1931.
․Bulk, available taped on reel.
․ESD-withstand voltage: up to 4KV
․The product itself will remain within RoHS compliant version.
Descriptions
․The series is designed for application required
high luminous intensity.
․The phosphor filled in the reflector converts the
blue emission of InGaN chip to ideal white.
Applications
․Message panels
․Optical Indicators
․Backlighting
․Marker Lights
Device Selection Guide
Chip
PART NO.
Lens Color
Material
Emitted Color
White
334-15/T2C1-7UWC
InGaN
Water Clear
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 1 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Package Dimensions
Notes:
1.All dimensions are in millimeters, and tolerance is 0.25mm except being specified.
2.Lead spacing is measured where the lead emerges from the package.
3.Protruded resin under flange is 1.5mm Max. LED.
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 2 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
IF
Rating
30
Unit
mA
mA
V
Continuous Forward Current
Peak Forward Current(Duty /10 @ 1KHZ)
Reverse Voltage
IFP
100
VR
5
℃
Operating Temperature
Storage Temperature
Topr
Tstg
Tsol
Pd
-40 ~ +85
-40 ~ +100
260
℃
℃
Soldering Temperature (T=5 sec)
Power Dissipation
mW
mA
V
110
Zener Reverse Current
Iz
100
Electrostatic Discharge
ESD
4K
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 3 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Production Designation
334-15/T2C1-□ □ □ □
Voltage Group
Luminous Intensity Bins
Color Group
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Condition
Min.
2.8
Typ.
Max. Units
Forward Voltage
VF
IF=20mA
Iz=5mA
--
--
3.6
--
V
V
Zener Reverse Voltage
Vz
5.2
Reverse Current
IR
VR=5V
--
--
--
50
uA
IV
IF=20mA
IF=20mA
mcd
Luminous Intensity
Viewing Angle
9000
--
18000
2θ1/2
15
--
--
--
deg
--
x
y
--
0.30
0.29
Chromaticity Coordinates
IF=20mA
--
--
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 4 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Luminous Intensity Combination (mcd at 20mA)
Min
9000
Max
Rank
U
11250
14250
18000
V
11250
14250
W
*Measurement Uncertainty of Luminous Intensity: 10%
Forward Voltage Combination (V at 20mA)
Rank
0
1
2
3
Forward Voltage
2.8~3.0
3.0~3.2
3.2~3.4
3.4~3.6
*Measurement Uncertainty of Forward Voltage: 0.1V
Color Combination ( at 20mA)
Group
7
Bins
B5+B6
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 5 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
CIE Chromaticity Diagram
0.8
0.6
5600K
7000K
9000K
0.4
0.2
0.0
B6
B5
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
Color Ranks (IF=20mA,Ta=25℃)
Color Ranks
CIE
X
Y
X
Y
0.287
0.295
0.307
0.315
0.307
0.315
0.33
0.311
0.294
0.33
0.296
0.276
0.311
0.294
B5
B6
0.339
0.318
*Measurement uncertainty of the color coordinates: 0.01
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 6 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Typical Electro-Optical Characteristics Curves
Relative Intensity vs. Wavelength
Forward Current vs. Forward Voltage
25
1.0
20
15
10
5
0.8
0.6
0.4
0.2
0.0
0
2.0
2.5
3.0
3.5
4.0
4.5
350 400 450 500 550 600 650 700 750 800
Forward Voltage(V)
Wavelength(nm)
Relative Intensity vs. Forward Current
Forward Current vs. Ambient Temp.
40
30
20
10
0
1.5
1.0
0.5
0.0
0
20
40
60
80
100
0
5
10
15
20
25
Ambient Temperature Ta(OC)
Forward Current(mA)
Chromaticity Coordinate vs. Forward Current
Relative Intensity vs. Angle Displacement
90O
1.0
60O
30O
0O
10O
20O
0.330
30O
0.320
0.310
O
40
50O
60O
70O
x
0.300
y
0.5
0.290
0.280
0.270
0.260
80O
90O
1.0
0
0
10
20
30
40
50
0
0.5
Forward Current(mA)
Radiation Angle
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Established date:01-20-2009
Rev 1
Page: 7 of 12
Device Number: DLE-0000791
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Packing Specification
Anti-electrostatic bag
Label
Inner Carton
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks of Luminous Intensity and Forward Voltage
HUE: Color Rank
Outside Carton
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
Packing Quantity
1. 500 PCS/1 Bag, 5 Bags/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 8 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
Notes
1. Lead Forming
ꢀ
During lead formation, the leads should be bent at a point at least 3mm from the base of the
epoxy bulb.
ꢀ
ꢀ
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage
the LED’s characteristics or it may break the LEDs.
ꢀ
ꢀ
Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures
may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead
position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration
of the epoxy resin and this will degrade the LEDs.
2. Storage
ꢀ
ꢀ
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from
Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or
more, they can be stored for a year in a sealed container with a nitrogen atmosphere and
moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity
environments where condensation can occur.
3. Soldering
ꢀ
ꢀ
Careful attention should be paid during soldering. When soldering, leave more then 3mm
from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is
recommended.
Recommended soldering conditions:
Hand Soldering
300℃ Max. (30W
Max.)
DIP Soldering
100℃ Max. (60 sec
Max.)
Temp. at tip of
Preheat temp.
iron
3 sec Max.
Soldering time
Distance
Bath temp. & time
Distance
260 Max., 5 sec Max
3mm Min. (From
solder joint to epoxy
bulb)
3mm Min.(From
solder joint to
epoxy bulb)
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Established date:01-20-2009
Rev 1
Page: 9 of 12
Device Number: DLE-0000791
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
laminar wave
Fluxing
Prehead
ꢀ
Avoiding applying any stress to the lead frame while the LEDs are at high temperature
particularly when soldering.
ꢀ
ꢀ
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or
vibration until the LEDs return to room temperature.
ꢀ
ꢀ
ꢀ
A rapid-rate process is not recommended for cooling the LEDs down from the peak
temperature.
Although the recommended soldering conditions are specified in the above table, dip or
handsoldering at the lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature
and dwell time in the solder wave.
4. Cleaning
ꢀ
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for
a duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of
ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the
assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause
damage to the LED
ꢀ
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 10 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
5. Circuit Protection
ꢀ
Below the zener reference voltage Vz, all the current flows through LED and as the voltage
rises to Vz, the zener diode “breakdown." If the voltage tries to rise above Vz current flows
through the zener branch to keep the voltage at exactly Vz.
ꢀ
When the LED is connected using serial circuit, if either piece of LED is no light up but
current can’t flow through causing others to light down. In new design, the LED is parallel
with zener diode. if either piece of LED is no light up but current can flow through causing
others to light up.
6. Heat Management
ꢀ
Heat management of LEDs must be taken into consideration during the design stage of LED
application. The current should be de-rated appropriately by referring to the de-rating curve
found in each product specification.
ꢀ
The temperature surrounding the LED in the application should be controlled. Please refer to
the data sheet de-rating curve.
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Rev 1
Page: 11 of 12
Device Number: DLE-0000791
Established date:01-20-2009
Established by: Ruby Lin
Technical Data Sheet
334-15/T2C1-7UWC
7. ESD (Electrostatic Discharge)
ꢀ
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
ꢀ
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling
LEDs.
ꢀ
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the
LEDs plastic lens as a result of friction between LEDs during storage and handing.
ꢀ
8. Other
ꢀ
Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
ꢀ
ꢀ
When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Everlight Electronics Co., Ltd.
http\\:www.everlight.com
Established date:01-20-2009
Rev 1
Page: 12 of 12
Device Number: DLE-0000791
Established by: Ruby Lin
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明