PT15-21B-TR8 [EVERLIGHT]

Phototransistor; PHOTOTRANSISTOR


型号：	PT15-21B-TR8
厂家：	EVERLIGHT ELECTRONICS CO., LTD
描述：	Phototransistor PHOTOTRANSISTOR
文件：	总10页 (文件大小：185K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Technical Data Sheet

1206 Package Phototransistor

PT15-21B/TR8

Features

․Fast response time

․High photo sensitivity

․Small junction capacitance

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

․PT15-21B/TR8 is a phototransistor in miniature SMD package

which is molded in a black plastic with flat top view lens.

The device is spectrally matched to infrared emitting diode.

Applications

․Miniature switch

․Counters and sorter

․Position sensor

․Infrared applied system

Device Selection Guide

Chip

LED Part No.

Lens Color

Material

Silicon

Black

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 1 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Package Dimensions

Emitter

Collector

Notes: 1.All dimensions are in millimeters

2.Tolerances unless dimensions ±0.1mm

Absolute Maximum Ratings (Ta=25℃)

Parameter

Collector-Emitter Voltage

Emitter-Collector-Voltage

Collector Current

Symbol

V_CEO

V_ECO

I_C

Rating

Units

℃

Operating Temperature

Storage Temperature

Soldering Temperature

T_opr

-25 ~ +85

-40 ~ +85

260

℃

T_stg

℃

T_sol

Power Dissipation at(or below)

P_c

25℃Free Air Temperature

Notes: *1:Soldering time≦5 seconds.

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 2 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Electro-Optical Characteristics (Ta=25℃)

Parameter

Symbol

Condition

Min Typ Max Unit

λ_0.5

Rang Of Spectral Bandwidth

---

730

---

1100 nm

λ_P

Wavelength Of Peak Sensitivity

---

940

---

I_C=100μA

Collector-Emitter Breakdown

Voltage

BV_CEO

---

Ee=0mW/cm²

I_E=100μA

Emitter-Collector Breakdown

Voltage

BV_ECO

V_CE(sat)

I_CEO

---

0.4

100

Ee=0mW/cm²

Collector-Emitter Saturation

Voltage

I_C=2mA

---

Ee=1m W/cm²

V_CE=20V

Collector Dark Current

Ee=0mW/cm²

V_CE=5V

On State Collector Current

I_C(ON)

0.1

0.3

Ee=1mW /cm²

Rise Time

Fall Time

t_r

t_f

---

V_CE=5V

I_C=1mA

R_L=1000Ω

μS

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Prepared date：06-06-2006

Rev 2

Page: 3 of 10

Device No：DTT-015-031

Prepared by：Jaine Tsai

PT15-21B/TR8

Typical Electro-Optical Characteristics Curves

Fig.1Collector Power Dissipation vs.

Ambient Temperature

Fig.2 Spectral Sensitivity

1.0

100

Ta=25C

0.8

0.6

0.4

0.2

-25

75 85 100

700 800 900 1000 1100 1300

Fig.3 Relative Collector Current vs.

Ambient Temperature

Fig.4 Collector Current vs.

Irradiance

100

160

140

120

100

0.1

0.01

10 20

30 40 50 60 70

0.5

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Prepared date：06-06-2006

Rev 2

Page: 4 of 10

Device No：DTT-015-031

Prepared by：Jaine Tsai

PT15-21B/TR8

Typical Electro-Optical Characteristics Curves

Fig.5 Collector Dark Current vs.

Ambient Temperature

Fig.6 Collector Current vs.

Collector-Emitter Voltage

100

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 5 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 6 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3

seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more

intervals, and do soldering of each terminal. Be careful because the damage of the product is often

started at the time of the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed

beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 7 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Reliability Test Item And Condition

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

NO. Item

Test Conditions

Test Hours/ Sample Failure

Ac/Re

Cycles

Sizes

22pcs

Judgement

Criteria

TEMP.：260℃±5℃

1 REFLOW

6Mins

0/1

5secs

_C(ON)≦L×0.8

H : +100℃

15mins

2 Temperature Cycle

50Cycles

5mins

L：Lower

Specification

Limit

L : -40℃

15mins

H :+100℃

5mins

3 Thermal Shock

50Cycles

22pcs

0/1

10secs

5mins

L :-10℃

TEMP.：+100℃

4 High Temperature

Storage

1000hrs

22pcs

0/1

TEMP.：-40℃

5 Low Temperature

Storage

6 DC Operating Life V_CE=5V

1000hrs

22pcs

0/1

85℃ / 85% R.H

7 High Temperature/

High Humidity

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 8 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Package Dimensions

Taping Dimensions

Emitter

Collector

Unit:mm

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Rev 2

Page: 9 of 10

Device No：DTT-015-031

Prepared date：06-06-2006

Prepared by：Jaine Tsai

PT15-21B/TR8

Packing Quantity Specification

1.2000Pcs/1Volume，1Volume/1Bag

2.10Boxes/1Carton

Label Form Specification

CPN: Customer’s Production Number

P/N : Production Number

QTY: Packing Quantity

CAT: Ranks

RoHS

PT15-21B/TR8

HUE: Peak Wavelength

REF: Reference

LOT No: Lot Number

MADE IN TAIWAN: Production Place

Notes

1. Above specification may be changed without notice. EVERLIGHT will reserve authority on

material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions

for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for

any damage resulting from use of the product which does not comply with the absolute

maximum ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s

consent.

EVERLIGHT ELECTRONICS CO., LTD.

Office: No 25, Lane 76, Sec 3, Chung Yang Rd,

Tucheng, Taipei 236, Taiwan, R.O.C

Tel: 886-2-2267-2000, 2267-9936

Fax: 886-2267-6244, 2267-6189, 2267-6306

http:\\www.everlight.com

Everlight Electronics Co., Ltd.

http:\\www.everlight.com

Prepared date：06-06-2006

Rev 2

Page: 10 of 10

Device No：DTT-015-031

Prepared by：Jaine Tsai

相关型号：