NC7WB3125L8X [FAIRCHILD]
TinyLogic UHS 2-Bit Low Power Bus Switch; TinyLogic UHS 2位低功耗总线开关型号: | NC7WB3125L8X |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | TinyLogic UHS 2-Bit Low Power Bus Switch |
文件: | 总9页 (文件大小:197K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
May 2000
Revised April 2003
NC7WB3125
TinyLogic UHS 2-Bit Low Power Bus Switch
General Description
Features
The NC7WB3125 is a 2-bit ultra high-speed CMOS FET
bus switch with TTL-compatible active LOW control inputs.
The low On Resistance of the switch allows inputs to be
connected to outputs with minimal propagation delay and
without generating additional ground bounce noise. The
device is organized as a 2-bit switch with independent bus
enable (OE) controls. When OE is LOW, the switch is ON
and Port A is connected to Port B. When OE is HIGH, the
■ Space saving US8 surface mount package
■ MicroPak leadless package
■ Typical 3Ω switch resistance at 5.0V VCC
■ Minimal propagation delay through the switch
■ Power down high impedance input/output
■ Zero bounce in flow through mode
■ TTL compatible active LOW control inputs
■ Control inputs are overvoltage tolerant
■ Bus switch replacement for Logic x125 part
switch is OPEN and
a high-impedance state exists
between the two ports. Control inputs tolerate voltages up
to 5.5V independent of VCC
.
Ordering Code:
Product
Code
Order
Package
Package Description
Supplied As
Number
Number Top Mark
NC7WB3125K8X MAB08A
WB25
T4
8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3k Units on Tape and Reel
8-Lead MicroPak, 1.6 mm Wide 5k Units on Tape and Reel
NC7WB3125L8X MAC08A
(Preliminary)
TinyLogic is a registered trademark of Fairchild Semiconductor Corporation.
MircoPak is a trademark of Fairchild Semiconductor Corporation.
© 2003 Fairchild Semiconductor Corporation
DS500376
www.fairchildsemi.com
Logic Diagram
Connection Diagrams
(Top View)
Pin One Orientation Diagram
Pin Descriptions
Pin Name
Description
Bus A
A
B
Bus B
AAA represents Product Code Top Mark - see ordering code
Note: Orientation of Top Mark determines Pin One location. Read the top
product code mark left to right, Pin One is the lower left pin (see diagram).
OE
Bus Enable Input
Function Table
Pad Assignments for MicroPak
Bus Enable Input OE
Function
L
B Connected to A
Disconnected
H
(Top Thru View)
www.fairchildsemi.com
2
Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions (Note 3)
Supply Voltage (VCC
)
−0.5V to +7.0V
−0.5V to +7.0V
−0.5V to +7.0V
DC Switch Voltage (VS)
DC Output Voltage (VIN) (Note 2)
DC Input Diode Current
(IIK) VIN < 0V
Supply Operating (VCC
Control Input Voltage (VIN
Switch Input Voltage (VIN
Output Voltage (VOUT
)
4.0V to 5.5V
0V to 5.5V
)
)
0V to 5.5V
−50 mA
)
0V to 5.5V
DC Output (IOUT) Current
DC VCC or Ground Current
128 mA
Operating Temperature (TA)
Input Rise and Fall Time (tr, tf)
Switch Control Input
Switch I/O
−40°C to +85°C
(ICC/IGND
)
±100 mA
−65°C to +150°C
+150°C
0 ns/V to 5 ns
0 ns/V to DC
250°C/W
Storage Temperature Range (TSTG
)
Junction Temperature under Bias (TJ)
Junction Lead Temperature (TL)
(Soldering, 10 Seconds)
Thermal Resistance (θJA
)
+260°C
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum ratings.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Power Dissipation (PD) @ +85°C
250 mW
Note 2: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
Note 3: Unused logic inputs must be held HIGH or LOW. They may not
float.
DC Electrical Characteristics
VCC
T
A = −40°C to +85°C
Symbol
Parameter
Units
Conditions
IIN = −18 mA
(V)
4.5
Min
Typ
Max
VIK
Clamp Diode Voltage
HIGH Level Input Voltage
LOW Level Input Voltage
HIGH Level Output Voltage
Input Leakage Current
Switch OFF Leakage Current
Switch On Resistance
(Note 4)
−1.2
V
V
VIH
VIL
4.0 to 5.5
4.0 to 5.5
4.0 to 5.5
5.5
2.0
0.8
V
VOH
IIN
See Figure 3
V
VIN = VCC
±1.0
±1.0
7
µA
µA
0 ≤ VIN ≤ 5.5V
0 ≤ A, B ≤ VCC
IOFF
RON
5.5
4.5
3
3
VIN = 0V, IIN = 64 mA
VIN = 0V, IIN = 30 mA
VIN = 2.4V, IIN = 15 mA
VIN = 2.4V, IIN = 15 mA
VIN = VCC or GND
4.5
7
Ω
4.5
6
15
20
3
4.0
10
ICC
Quiescent Supply Current
5.5
µA
I
OUT = 0
IN = 3.4V, One OE Input only,
Other OE = VCC
∆ ICC
Increase in ICC per Input (Note 5)
5.5
1
2.5
mA
V
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B) pins.
Note 5: Per TTL driven input (VIN = 3.4V, control input only). A and B pins do not contribute to ICC
.
3
www.fairchildsemi.com
AC Electrical Characteristics
TA = −40°C to +85°C,
VCC
CL = 50 pF, RU = RD = 500Ω
Symbol
Parameter
Units
Conditions
Figure
(V)
Min
Typ
Max
Number
tPHL
tPLH
tPZL
tPZH
tPLZ
tPHZ
,
Propagation Delay Bus to Bus
(Note 6)
4.0 to 5.5
0.25
ns
VI = OPEN
Figures
1, 2
,
Output Enable Time
4.5 to 5.5
4.0
0.8
0.8
0.8
0.8
2.5
3.0
3.1
2.9
4.2
4.6
4.8
4.4
VI = 7V for tPZL
VI = 0V for tPZH
VI = 7V for tPLZ
VI = 0V for tPHZ
Figures
1, 2
ns
ns
,
Output Disable Time
4.5 to 5.5
4.0
Figures
1, 2
Note 6: This parameter is guaranteed by design. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of
the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance). The specified limit is calculated on this basis.
Capacitance
Symbol
Parameter
Typ
Max
Units
Conditions
CIN
Control Pin Input Capacitance
2.5
pF
V
V
V
CC = 0V
CI/O (OFF)
CI/O (ON)
Port Off Capacitance
6
pF
pF
CC = 5.0V = OE
Switch ON Capacitance
12
CC = 5.0V, OE = 0V
AC Loading and Waveforms
Input driven by 50Ω source terminated in 50Ω
CL includes load and stray capacitance
Input PRR = 1.0 MHz; tW = 500 ns
FIGURE 1. AC Test Circuit
FIGURE 2. AC Waveforms
www.fairchildsemi.com
4
DC Characteristics
FIGURE 3. Typical High Level Output Voltage vs. Supply Voltage
5
www.fairchildsemi.com
Tape and Reel Specification
TAPE FORMAT for US8
Package
Tape
Section
Number
Cavities
125 (typ)
250
Cavity
Status
Empty
Filled
Cover Tape
Status
Designator
Leader (Start End)
Carrier
Sealed
K8X
Sealed
Trailer (Hub End)
75 (typ)
Empty
Sealed
TAPE DIMENSIONS inches (millimeters)
TAPE FORMAT for MicroPak
Package
Tape
Section
Number
Cavities
125 (typ)
250
Cavity
Status
Empty
Filled
Cover Tape
Status
Designator
Leader (Start End)
Carrier
Sealed
L8X
Sealed
Trailer (Hub End)
75 (typ)
Empty
Sealed
TAPE DIMENSIONS inches (millimeters)
www.fairchildsemi.com
6
Tape and Reel Specification (Continued)
REEL DIMENSIONS inches (millimeters)
Tape
Size
A
B
C
D
N
W1
W2
W3
7.0
0.059
0.512
0.795
2.165 0.331 + 0.059/−0.000
0.567
W1 + 0.078/−0.039
(W1 + 2.00/−1.00)
8 mm
(177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/−0.00)
(14.40)
7
www.fairchildsemi.com
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide
Package Number MAB08A
www.fairchildsemi.com
8
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8-Lead MicroPak, 1.6 mm Wide
Package Number MAC08A
(Preliminary)
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be rea-
sonably expected to result in a significant injury to the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
9
www.fairchildsemi.com
相关型号:
NC7WB3306K8X_NL
Bus Driver, CBT/FST/QS/5C/B Series, 2-Func, 1-Bit, True Output, CMOS, PDSO8, 3.10 MM, MO-187CA, US-8
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明