MC33977DWR2 [FREESCALE]
Single Gauge Driver; 单计驱动器型号: | MC33977DWR2 |
厂家: | Freescale |
描述: | Single Gauge Driver |
文件: | 总37页 (文件大小:1775K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: MC33977
Rev. 2.0, 1/2007
Freescale Semiconductor
Technical Data
Single Gauge Driver
33977
The 33977 is a Serial Peripheral Interface (SPI) Controlled, stepper
motor gauge driver Integrated Circuit (IC). This monolithic IC consists
of a dual H-Bridge coil driver and its associated control logic. The H-
Bridge drivers are used to automatically control the speed, direction,
and magnitude of current through the coils of a two-phase
instrumentation stepper motor, similar to an MMT-licensed AFIC 6405
of Switec MS-X156.xxx motor.
SINGLE GAUGE DRIVER
The 33977 is ideal for use in instrumentation systems requiring
distributed and flexible stepper motor gauge driving. The device also
eases the transition to stepper motors from air core motors by
emulating the damped air core pointer movement.
Features
• MMT-Licensed Two-Phase Stepper Motor Compatible
• Switec MS-X15.xxx Stepper Motor Compatible
• Minimal Processor Overhead Required
• Fully Integrated Pointer Movement and Position State Machine
with Air Core Movement Emulation
• 4096 Possible Steady State Pointer Positions
• 340° Maximum Pointer Sweep
• Maximum Acceleration of 4500°/s2
DW SUFFIX
EG SUFFIX (Pb-FREE)
98ASB42344B
24-PIN SOICW
• Maximum Pointer Velocity of 400°/s
ORDERING INFORMATION
Temperature
• Analog Microstepping (12 Steps/Degrees of Pointer Movement)
• Pointer Calibration and Return to Zero (RTZ)
• Controlled via 16-Bit SPI Messages
Device
Package
Range (T )
A
• Internal Clock Capable of Calibration
• Low Sleep Mode Current
• Pb-Free Packaging Designated by suffix code EG
MC33977DW/R2
-40°C to 125°C
24 SOICW
MCZ33977EG/R2
V
PWR
33977
VPWR
V
DD
5.0 V
Regulator
VDD
SIN+
SIN-
Motor
RTZ
RST
CS
COS+
COS-
MCU
SCLK
SI
SO
GND
Figure 1. 33977 Simplified Application Diagram
Freescale Semiconductor, Inc. reserves the right to change the detail specifications,
as may be required, to permit improvements in the design of its products.
© Freescale Semiconductor, Inc., 2007. All rights reserved.
INTERNAL BLOCK DIAGRAM
INTERNAL BLOCK DIAGRAM
VPWR
VDD
CS
INTERNAL
REGULATOR
COS+
COS-
COS
SCLK
SO
SPI
SI
LOGIC
RST
STATE
MACHINE
H-BRIDGE
AND
SIN+
SIN-
UNDER-
AND
ILIM
CONTROL
OVERVOLTAGE
DETECT
OVERTEMPERATURE
DETECT
SIN
VDD
SIGMA-DELTA
ADC
MULTIPLEXER
OSCILLATOR
AGND
RTZ
GND (8)
Figure 2. 33977 Simplified Internal Block Diagram
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
2
PIN CONNECTIONS
PIN CONNECTIONS
COS+
COS-
SIN+
SIN-
GND
GND
GND
GND
CS
NC
NC
NC
NC
GND
GND
GND
GND
VPWR
RST
VDD
RTZ
SCLK
SO
SI
Figure 3. 33977 Pin Connections
Table 1. 33977 Pin Definitions
A functional description of each pin can be found in the Functional Pin Description section beginning onpage 10.
Pin
Pin Name Pin Function
Formal Name
Definition
(MS Motor
Pin #)
H-Bridge Outputs 0
Each pin is the output of a half-bridge, designed to source or sink current.
Output
COS+ (MS #4)
COS- (MS #3)
SIN+ (MS #1)
SIN- (MS #2)
1
2
3
4
5 to 8,
17 to 20
GND
Ground
Ground pins
N/A
Input
Input
Output
Input
9
Chip Select
Serial Clock
Serial Output
Serial Input
Return to Zero
This pin is connected to a chip select output of a Large Scale Integration
(LSI) Master IC and controls which device is addressed.
CS
10
11
12
13
SCLK
This pin is connected to the SCLK pin of the master device and acts as a
bit clock for the SPI port.
SO
SI
This pin is connected to the SPI Serial Data Input pin of the Master device
or to the SI pin of the next device in a daisy chain.
This pin is connected to the SPI Serial Data Output pin of the Master
device from which it receives output command data.
RTZ
This is a multiplexed output pin for the non-driven coil, during a Return to
Zero (RTZ) event.
Multiplexed
Output
14
15
VDD
RST
Voltage
Reset
This SPI and logic power supply input will work with 5.0 V supplies.
Input
Input
This pin is connected to the Master and is used to reset the device, or
place it into a sleep state by driving it to Logic [1]. When this pin is driven
to Logic [0], all internal logic is forced to the default state. This input has
an internal active pull-up.
16
VPWR
NC
Battery Voltage
No Connect
Power supply
Input
–
21, 22, 23, 24
These pins are not connected to any internal circuitry, or any other pin,
and may be connected to the board where convenient.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
3
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
MAXIMUM RATINGS
Table 2. Maximum Ratings
All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or
permanent damage to the device.
Ratings
Symbol
Value
Unit
ELECTRICAL RATINGS
Power Supply Voltage
Steady-State
V
V
PWRSS
-0.3 to 41
-0.3 to 7.0
40
Input Pin Voltage (1)
V
V
mA
V
IN
SIN± COSI± Continuous Current Per Output (2)
I
OUTMAX
ESD Voltage (3)
V
ESD
Human Body Model (HBM)
Machine Model (MM)
Charge Device Model (CDM)
±2000
±2000
±200
THERMAL RATINGS
Operating Temperature
Ambient
°C
TA
TJ
-40 to 125
-40 to 150
Junction
Storage Temperature
TSTG
-55 to 150
°C
Thermal Resistance
Junction-to-Ambient
Junction-to-Lead
°C/W
RΘJA
RΘJL
60
20
(5)
Peak Package Reflow Temperature During Reflow (4)
,
TPPRT
Note 5
°C
Notes
1. Exceeding voltage limits on Input pins may cause permanent damage to the device.
2. Output continuous output rating so long as maximum junction temperature is not exceeded. Operation at 125°C ambient temperature
will require maximum output current computation using package thermal resistances.
3. ESD testing is performed in accordance with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 Ω), the Machine Model (MM)
(CZAP = 200 pF, RZAP = 0 Ω), and the Charge Device Model (CDM).
4. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may
cause malfunction or permanent damage to the device.
5. Freescale’s Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow
Temperature and Moisture Sensitivity Levels (MSL),
Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e.
MC33xxxD enter 33xxx), and review parametrics.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
4
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Characteristics noted under conditions 4.75 V < VDD < 5.25 V, and -40°C < TA< 125°C, unless otherwise noted. Typical
values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER INPUT (VDD)
Battery Supply Voltage Range
Fully Operational
VPWR
V
6.5
4.0
–
26
26
Limited Operation (6), (7)
VPWR Supply Current
IPWR
mA
Gauge Outputs ON, No Output Loads
–
4.0
6.0
VPWR Supply Current (All Outputs Disabled)
Reset = Logic [0], VDD = 5.0 V
µA
IPWRSLP1
IPWRSLP2
–
–
42
15
60
25
Reset = Logic [0], VDD = 0 V
Overvoltage Detection Level (8)
VPWROV
VPWRUV
VDD
26
5.0
4.5
–
32
5.6
5.0
–
38
6.2
5.5
4.5
V
V
V
V
Undervoltage Detection Level (9)
Logic Supply Voltage Range (5.0 V Nominal Supply)
Under VDD Logic Reset
VDDUV
VDD Supply Current
Sleep: Reset Logic [0]
Outputs Enabled
IDDOFF
IDDON
–
–
40
65
µV
1.0
1.8
mA
POWER OUTPUT (SIN-, SIN+, COS-, COS+)
Microstep Output (Measured Across Coil Outputs)
SIN± (COS±) (Refer to Pin Definitions onpage 3)
ROUT = 200 Ω, PE6 = 0
V
Steps
Pin Definitions
VST6
VST5
VST4
VST3
VST2
VST1
VST0
4.82
5.3
6.0
6, 18,
0, 12
0.94 VST6 0.97 VST6
1.0 VST6
5, 7, 17, 19
4, 8, 16, 20
3, 9, 15, 21
2, 10, 14, 22
1, 11, 13, 23
0, 12
1, 11, 13, 23
2, 10, 14, 22
3, 9, 15, 21
5, 7, 17, 19
5, 7, 17, 19
6, 18
0.84 VST6 0.87 VST6 0.96 VST6
0.68 VST6 0.71 VST6 0.8 VST6
0.47 VST6 0.50 VST6 0.57 VST6
0.23 VST6 0.26 VST6 0.31 VST6
0.1
0.0
0.1
Full Step Active Output (Measured Across Coil Outputs) (10)
SIN± (COS±), Steps 1,3 (Pin Definitions 0 and 2)
VFS
V
4.9
5.3
6.0
Notes
6. Outputs and logic remain active; however, the larger coil voltage levels may be clipped. The reduction in drive voltage may result in a
loss of position control.
7. The logic will reset at some level below the specified Limited Operational minimum.
8. Outputs will disable and must be re-enabled via the PECCR command.
9. Outputs remain active; however, the reduction in drive voltage may result in a loss of position control.
10. See Figure 7.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
5
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics (continued)
Characteristics noted under conditions 4.75 V < VDD < 5.25 V, and -40°C < TA< 125°C, unless otherwise noted. Typical
values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER OUTPUT (SIN-, SIN+, COS-, COS+) (Continued)
Microstep Full Step Output (Measured from Coil Low Side to Ground)
SIN± (COS±) IOUT = 30 mA
VLS
V
0.0
0.1
0.3
Output Flyback Clamp (11)
VFB
ILIM
–
VST6 + 0.5 VST6 + 1.0
V
Output Current Limit (Output - VST6
Overtemperature Shutdown (12)
Overtemperature Hysteresis (12)
)
40
100
–
170
180
16
mA
°C
°C
TSD
155
8.0
THYST
–
CONTROL I/O (SI, SCLK, CS, RST, SO)
Input Logic High Voltage (12)
VIH
VIL
2.0
–
–
–
0.8
–
V
V
Input Logic Low Voltage (12)
–
Input Logic Voltage Hysteresis (12)
Input Logic Pull-Down Current (SI, SCLK)
Input Logic Pull-Up Current (CS, RST)
SO High State Output Voltage (IOH = 1.0 mA)
SO Low State Output Voltage (IOL = 1.6 mA)
SO Tri-State Leakage Current (CS = 3.5 V)
Input Capacitance (13)
VINHYST
IDWN
IUP
–
3.0
5.0
0.8 VDD
–
100
–
mV
µA
µA
V
20
20
–
–
VSOH
VSOL
ISOLK
CIN
–
0.2
0.0
4.0
–
0.4
5.0
12
20
V
-5.0
–
µA
pF
pF
SO Tri-State Capacitance (13)
CSO
–
ANALOG TO DIGITAL CONVERTER (RTZ ACCUMULATOR COUNT)
ADC Gain (12), (14)
G
100
188
270
Counts/V/
ms
ADC
Notes
11. Outputs remain active; however, the reduction in drive voltage may result in a loss of position control.
12. This parameter is guaranteed by design; however, it is not production tested.
13. Capacitance not measured. This parameter is guaranteed by design; however, it is not production tested.
14. Reference RTZ Accumulator (Typical) on page 30
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
6
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. Dynamic Electrical Characteristics
Characteristics noted under conditions 4.75 V < VDD < 5.25 V, and -40°C < TA < 125°C, unless otherwise noted. Typical
values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER OUTPUT AND CLOCK TIMINGS (SIN+, SIN-, COS+, COS-) CS
SIN± (COS±) Output Turn ON Delay Time (Time from Rising CS
Enabling Outputs to Steady State Coil Voltages and Currents) (15)
tDLYON
ms
ms
–
–
1.0
SIN± (COS±) Output Turn OFF Delay Time (Time from Rising CS
Disables Outputs to Steady State Coil Voltages and Currents) (15)
tDLYOFF
–
–
1.0
1.7
Uncalibrated Oscillator Cycle Time
tCLU
tCLC
0.65
1.0
µs
µs
Calibrated Oscillator Cycle Time
Calibration Pulse = 8.0 µs, PECCR D4 = Logic [0]
Calibration Pulse = 8.0 µs, PECCR D4 = Logic [1]
1.0
0.9
1.1
1.0
1.2
1.1
Maximum Pointer Speed (16)
VMAX
AMAX
–
–
–
–
400
°/s
Maximum Pointer Acceleration (16)
4500
°/s2
SPI INTERFACE TIMING (CS, SCLK, SO, SI, RST) (17)
Recommended Frequency of SPI Operation
fSPI
tLEAD
tLAG
–
167
167
–
1.0
–
2.0
–
MHz
ns
Falling Edge of CS to Rising Edge of SCLK (Required Setup Time) (18)
Falling Edge of SCLK to Rising Edge of CS (Required Setup Time) (18)
SI to Falling Edge of SCLK (Required Setup Time) (18)
Falling Edge of SCLK to SI (Required Hold Time) (18)
–
–
ns
tSISU
25
25
83
83
ns
tSIHOLD
–
ns
SO Rise Time
CL = 200 pF
tRSO
ns
–
25
50
tFSO
SO Fall Time
CL = 200 pF
ns
–
25
50
SI, CS, SCLK, Incoming Signal Rise Time (19)
tRSI
tFIS
–
–
–
–
–
–
–
–
–
–
50
50
ns
ns
µs
µs
µs
SI, CS, SCLK, Incoming Signal Fall Time (19)
Falling Edge of RST to Rising Edge of RST (Required Setup Time) (18)
Rising Edge of CS to Falling Edge of CS (Required Setup Time) (18), (20)
Falling Edge of RST to Rising Edge of CS (Required Setup Time) (18)
Notes
t
3.0
5.0
5.0
WRST
tCS
tEN
15. Maximum specified time for the 33977 is the minimum guaranteed time needed from the microcontroller.
16. The minimum and maximum value will vary proportionally to the internal clock tolerance. These numbers are based on an ideally
calibrated clock frequency of 1.0 MHz. These are not 100 percent tested.
17. The 33977 shall meet all SPI interface timing requirements specified in the SPI Interface Timing section of this table, over the specified
temperature range. Digital interface timing is based on a symmetrical 50 percent duty cycle SCLK Clock Period of 33 ns. The device shall
be fully functional for slower clock speeds. Reference Figure 4 and 5.
18. The required setup times specified for the 33977 are the minimum time needed from the microcontroller to guarantee correct operation.
19. Rise and Fall time of incoming SI, CS, and SCLK signals suggested for design consideration to prevent the occurrence of double pulsing.
20. The value is for a 1.0 MHz calibrated internal clock. The value will change proportionally as the internal clock frequency changes.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
7
ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. Dynamic Electrical Characteristics (continued)
Characteristics noted under conditions 4.75 V < VDD < 5.25 V, and -40°C < TA < 125°C, unless otherwise noted. Typical
values noted reflect the approximate parameter means at TA = 25°C under nominal conditions unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
SPI INTERFACE TIMING (CS, SCLK, SO, SI, RST) ‘ (CONTINUED)
Time from Falling Edge of CS to SO Low Impedance (22)
Time from Falling Edge of CS to SO High Impedance (23)
tSOEN
tSODIS
tVALID
–
–
–
145
4.0
ns
µs
ns
1.3
Time from Rising Edge of SCLK to SO Data Valid (24)
0.2 VDD = SO = 0.8 VDD, CL = 200 pF
–
90
150
Notes
21. The 33977 shall meet all SPI interface timing requirements specified in the SPI Interface Timing section of this table, over the specified
temperature range. Digital interface timing is based on a symmetrical 50 percent duty cycle SCLK Clock Period of 33 ns. The device shall
be fully functional for slower clock speeds.
22. Time required for output status data to be terminated at SO 1.0 kΩ load on SO.
23. Time required for output status data to be available for use at SO 1.0 kΩ load on SO.
24. Time required to obtain valid data out from SO following the rise of SCLK.
33977
Analog Integrated Circuit Device Data
8
Freescale Semiconductor
ELECTRICAL CHARACTERISTICS
TIMING DIAGRAMS
TIMING DIAGRAMS
V
V
IN
IL
RST
CS
0.2 V
DD
tWRST
t
CS
0.7 V
V
V
DD
IH
IL
0.7 V
DD
t
t
t
LAG
LEAD
RSI
V
IH
0.7 V
DD
DD
0.2 V
SCLK
SI
t
FIS
t
SISU
t
SI(HOLD)
Don’t Care
0.7 V
DD
Don’t Care
Valid
Valid
Don’t Care
0.2 V
DD
Figure 4. Input Timing Switching Characteristics
t
FIS
t
RSI
V
V
OH
3.5V
50%
SCLK
1.0V
OL
t
SO(EN)
V
V
OH
OL
V
0.7 DD
V
0.2 DD
SO
Low-to-High
t
RSO
t
VALID
t
RSO
SO
V
V
OH
OL
High-to-Low
V
0.7 DD
V
0.2 DD
t
SO(DIS)
Figure 5. Valid Data Delay Time and Valid Time Waveforms
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
This 33977 is a single-packaged, Serial Peripheral
INterface (SPI) controlled, single stepper motor gauge driver
integrated circuit (IC). This monolithic stepper IC consists of
[deleted two per D. Mortensen] a dual output H-Bridge coil
driver [deleted plural s for accurate tense] and the
associated control logic. The dual H-Bridge driver is used to
automatically control the speed, direction, and magnitude of
current through the coils of a two-phase instrumentation
stepper motor, similar to an MMT-licensed AFIC 6405 of
Switec MS-X 156.xxx motor.
FUNCTIONAL PIN DESCRIPTION
SCLK has an internal pull down (lDWN), as specified in the
section of the Static Electrical Characteristics Table. When
CS is logic [1], signals at the SCLK and SI pins are ignored
and SO is tri-stated (high impedance). Refer to the data
transfer Timing Diagrams on page 9.
COSINE POSITIVE (COS0+)
The H-Bridge pins linearly drive the sine and cosine coils
of a stepper motor, providing four-quadrant operation.
COSINE NEGATIVE (COS0-)
The H-Bridge pins linearly drive the sine and cosine coils
of a stepper motor, providing four-quadrant operation.
SERIAL OUTPUT (SO)
The SO data pin is a tri-stateable output from the Shift
register. The Status register bits are the first 16 bits shifted
out. Those bits are followed by the message bits clocked in
FIFO, when the device is in a daisy chain connection or being
sent words that are multiples of 16 bits. Data is shifted on the
rising edge of the SCLK signal. The SO pin will remain in a
high impedance state until the CS pin is put into a logic low
state.
SINE POSITIVE (SIN+)
The H-Bridge pins linearly drive the sine and cosine coils
of a stepper motor, providing four-quadrant operation.
SINE NEGATIVE (SIN-)
The H-Bridge pins linearly drive the sine and cosine coils
of a stepper motor, providing four-quadrant operation.
SERIAL INPUT (SI)
GROUND (GND)
The SI pin is the input of the SPI. Serial input information
is read on the falling edge of SCLK. A 16-bit stream of serial
data is required on the SI pin, beginning with the most
significant bit (MSB). Messages that are not multiples of 16
bits (e.g., daisy chained device messages) are ignored. After
transmitting a 16-bit word, the CS pin must be de-asserted
(logic [1]) before transmitting a new word. SI information is
ignored when CS is in a logic high state.
Ground pins.
CHIP SELECT (CS)
The pin enables communication with the master device.
When this pin is in a logic [0] state, the 33977 is capable of
transferring information to, and receiving information from,
the master. The 33977 latches data in from the Input Shift
registers to the addressed registers on the rising edge of CS.
RETURN TO ZERO (RTZ)
The output driver on the SO pin is enabled when CS is
logic [0]. When CS is logic high, signals at the SCLK and SI
pins are ignored and the SO pin is tri-stated (high
This is a multiplexed output pin for the non-driven coil,
during a Return to Zero (RTZ) event.
impedance). CS will only be transitioned from a logic [1] state
to a logic [0] state when SCLK is logic [0]. CS has an internal
pull-up (IUP) connected to the pin, as specified in the section
of the Static Electrical Characteristics Table.
VOLTAGE (VDD)
The SPI and logic power supply input will work with 5.0 V
supplies.
SERIAL CLOCK (SCLK)
RESET (RST)
SCLK clocks the Internal Shift registers of the 33977
device. The SI pin accepts data into the Input Shift register on
the falling edge of the SCLK signal, while the Serial Output
pin (SO) shifts data information out of the SO Line Driver on
the rising edge of the SCLK signal. It is important that the
SCLK pin be in a logic [0] state whenever the CS makes any
transition.
If the master decides to reset the device, or place it into a
sleep state, the RST pin is driven to a Logic [0]. A Logic [0] on
the RST pin forces all internal logic to the known default state.
This input has an internal active pull-up.
VOLTAGE POWER (VPWR)
This is the power supply pin.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
10
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION (OPTIONAL)
FUNCTIONAL INTERNAL BLOCK DESCRIPTION (OPTIONAL)
Internal
SPI
Logic
Oscillator
RTZ
Reference
Under and
Overvoltage
Detect
H-Bridge
and Control
Figure 6. Functional Internal 33977 Block Illustration
SERIAL PERIPHERAL INTERFACE (SPI)
OSCILLATOR
This circuitry manages incoming messages and outgoing
status data.
The internal oscillator generates the internal clock for all
timing critical features.
LOGIC
H-BRIDGE AND CONTROL
This design element includes internal logic including state
machines and message decoding.
This circuitry contains the output coil drivers and the
multiplexers necessary for four quadrant operation and RTZ
sequencing. This circuitry is repeated for the Sine and Cosine
coils.
INTERNAL REFERENCE
• Overtemperature — Each output includes an
overtemperature sensing circuit
This design element is used for step value levels.
• ILIM — Each output is current limited
UNDER AND OVERVOLTAGE DETECTION
This design element detects when VPWR is out of the
normal operating range.
RETURN TO ZERO (RTZ)
This circuitry outputs the voltage present on the non-driven
coil during RTZ operation.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
STATE MACHINE OPERATION
The 33977 is ideal for use in instrumentation systems
requiring distributed and flexible stepper motor gauge driving.
The device also eases the transition to stepper motors from
air core motors by emulating the air core pointer movement
with little additional processor bandwidth utilization. The two-
phase stepper motor has maximum allowable velocities and
acceleration and deceleration. The purpose of the stepper
motor state machine is to drive the motor with the maximum
performance while remaining within the motor’s voltage,
velocity, and acceleration constraints.
A requirement of the state machine is to ensure the
deceleration phase begins at the correct time and pointer
position. When commanded, the motor [will deleted PV]
accelerates constantly to the maximum velocity, and then it
moves toward the commanded position at the maximum
velocity. Eventually, the pointer reaches the calculated
location where the movement has to decelerate, safely
slowing to a stop at the desired position. During the
deceleration phase, the motor does [will deleted PV] not
exceed the maximum deceleration.
During normal operation, both stepper motor rotors are
microstepped at 24 steps per electrical revolution, illustrated
in Figure 7. A complete electrical revolution results in two
degrees of pointer movement. There is a second smaller
[parentheses removed-unnecessary] state machine in the IC
controlling these microsteps. The smaller state machine
receives clockwise or counter-clockwise index commands at
timed intervals, thereby stepping the motor in the appropriate
direction by adjusting the current in each coil. Normalized
values are provided in Table 5.
Figure 7. Clockwise Microsteps
Table 5. Coil Step Value
SINE
(Angle)*
COS (Angle -30)* COS (Angle -30)*
Step
Angle
PE6=0
PE6=1
0.866
0.966
1.0
0
1
0.0
15
0.0
1.0
0.259
0.5
0.965
0.866
0.707
0.5
2
30
3
45
0.707
0.866
0.966
1.0
0.966
0.866
0.707
0.500
0.259
0.0
4
60
5
75
0.259
0.0
6
90
7
105
120
135
150
0.966
0.866
0.707
0.5
-0.259
-0.5
8
9
-0.707
-0.866
-0.259
-0.500
10
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
12
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Table 5. Coil Step Value
and solving for v in terms of u, s, and t gives:
11
12
13
14
15
16
17
18
19
20
21
22
23
165
180
195
210
225
240
255
270
285
300
315
330
345
0.259
0.0
-0.966
-1.0
-0.707
-0.866
-0.966
-1.0
v = 2/t - u
The correct value of t to use in the equation is the
quantized value obtained above.
-0.259
-0.5
-0.966
-0.867
-0.707
-0.5
From these equations, a set of recursive equations can be
generated to give the allowed time step between motor
indexes when the motor is accelerating from a stop to its
maximum velocity.
-0.707
-0.866
-0.966
-1.0
-0.966
-0.866
-0.707
-0.500
-0.259
0.0
-0.259
0.0
Starting from a position p of 0 and a velocity v of 0, these
equations define the time interval between steps at each
position. To drive the motor at maximum performance, index
commands are given to the motor at these intervals. A table
is generated giving the time step *t at an index position n.
-0.966
-0.866
-0.707
-0.5
0.259
0.5
0.707
0.866
0.966
0.259
0.500
0.707
p0 = 0
v0 = 0
-0.259
* Denotes normalized values
⎡
2
⎤
-vn -1 + √
v
n -1 + 2a
The motor is stepped by providing index commands at
intervals. The time between steps defines the motor velocity
and the changing time defines the motor acceleration.
∆tn =
a
The state machine uses a table to define the allowed time
and the maximum velocity. A useful side effect of the table is
that it also allows the direct determination of the position at
which the velocity should reduce to stop the motor at the
desired position.
where ⎡ ⎤ indicates rounding up
vn = 2/∆tn - Vn -1
pn = n
Motor motion equations follow: [reworded for efficient use
of space]
Note: [chgd for format consistency AND deleted that as PV]
For pn = n, on the nth step, the motor [has deleted as PV]
indexed by n positions and has been accelerating steadily at
the maximum allowed rate. This is critical because it also
indicates the minimum distance the motor must travel while
decelerating to a stop. For example, the stopping distance is
also equal to the current value of n.
(The units of position are steps and velocity and
acceleration are in steps/second and steps/second2.)
From an initial position of 0 with an initial velocity (u), the
motor position (s) at a time (t) is:
s = ut + 1/2 at 2
The algorithm of pointer movement can be summarized in
two steps:
1. The pointer is at the previously commanded position
and is not moving.
For unit steps, the time between steps is:
2. A command to move to a pointer position (other than
the current position) has been received. Timed index
pulses are sent to the motor driver at an ever-
increasing rate, according to the time steps in Table 6,
until:
- u + √ u2 + 2a
⇒
t =
a
This defines the time increment between steps when the
motor is initially traveling at a velocity u. In the ROM, this time
is quantized to multiples of the system clock by rounding
upwards, ensuring acceleration never exceeds the allowed
value. The actual velocity and acceleration is calculated from
the time step actually used. Using:
aThe maximum velocity (default or selected) is
reached after which the step time intervals will no
longer decrease.
bThe distance in steps that remain to travel are less
than the current step time index value. The motor
then decelerates by increasing the step times
according to Table 6 until the commanded
position is reached. The state machine controls
the deceleration so that the pointer reaches the
commanded position efficiently.
v2 = u2 + 2as
and
v = u + at
An example of the velocity table for a particular motor is
provided in Table 6. This motor’s maximum speed is 4800
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
microsteps/s (at 12 microsteps/degrees), and its maximum
acceleration is 54000 microsteps/s2. The table is quantized
to a 1.0 MHz clock.
Table 6. Velocity Table
Velocity Time Between
Velocity
Velocity Time Between
Velocity
Velocity Time Between
Velocity
Position
Steps (µs)
(µSteps/s)
Position
Steps (µs)
(µSteps/s)
Position
Steps (µs)
(µSteps/s)
0
0.0
27217
13607
11271
7970
5858
4564
3720
3132
2701
2373
2115
1908
1737
1594
1473
1369
1278
1199
1129
1066
1010
960
0.00
36.7
76
77
380
377
374
372
369
366
364
361
358
356
354
351
349
347
344
342
340
338
336
334
332
330
328
326
324
322
321
319
317
315
314
312
310
309
307
306
2631.6
2652.5
2673.8
2688.2
2710.0
2732.2
2747.3
2770.1
2793.3
2809.0
2824.9
2849.0
2865.3
2881.8
2907.0
2924.0
2941.2
2958.6
2976.2
2994.0
3012.0
3030.3
3048.8
3067.5
3086.4
3105.6
3115.3
3134.8
3154.6
3174.6
3184.7
3205.1
3225.8
3236.2
3257.3
3268.0
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
257
256
255
254
254
253
252
251
250
249
248
248
247
246
245
244
244
243
242
241
241
240
239
238
238
237
236
265
235
234
233
233
232
231
231
230
3891.1
3906.3
3921.6
3937.0
3937.0
3952.6
3968.3
3984.1
4000.0
4016.1
4032.3
4032.3
4048.6
4065.0
4081.6
4098.4
4098.4
4115.2
4132.2
4149.4
4149.4
4166.7
4184.1
4201.7
4201.7
4219.4
4237.3
4255.3
4255.3
4273.5
4291.8
4291.8
4310.3
4329.0
4329.0
4347.8
1
2
73.5
78
3
88.7
79
4
125.5
170.7
219.1
268.8
319.3
370.2
421.4
472.8
524.1
575.7
627.4
678.9
730.5
782.5
834.0
885.7
938.1
990.1
1041.7
1091.7
1140.3
1187.6
1231.5
1275.5
1315.8
1356.9
1396.6
1434.7
1470.6
1508.3
1543.2
1577.3
80
5
81
6
82
7
83
8
84
9
85
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
86
87
88
89
90
91
92
93
94
95
96
97
98
916
99
877
100
101
102
103
104
105
106
107
108
109
110
111
842
812
784
760
737
716
697
680
663
648
634
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
14
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Table 6. Velocity Table (continued)
Velocity Time Between
Velocity
Velocity Time Between
Velocity
Velocity Time Between
Velocity
Position
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Steps (µs)
(µSteps/s)
Position
Steps (µs)
(µSteps/s)
Position
Steps (µs)
(µSteps/s)
621
608
596
585
575
565
555
546
538
529
521
514
507
500
493
487
481
475
469
464
458
453
448
444
439
434
430
426
422
418
414
410
406
403
399
396
393
389
386
383
1610.3
1644.7
1677.9
1709.4
1739.1
1769.9
1801.8
1831.5
1858.7
1890.4
1919.4
1945.5
1972.4
2000.0
2028.4
2053.4
2079.0
2105.3
2132.2
2155.2
2183.4
2207.5
2232.1
2252.3
2277.9
2304.1
2325.6
2347.4
2369.7
2392.3
2415.5
2439.0
2463.1
2481.4
2506.3
2525.3
2544.5
2570.7
2590.7
2611.0
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
304
303
301
300
298
297
295
294
293
291
290
289
287
286
285
284
282
281
280
279
278
277
275
274
273
272
271
270
269
268
267
266
265
264
263
262
261
260
259
258
3289.5
3300.3
3322.3
3333.3
3355.7
3367.0
3389.8
3401.4
3413.0
3436.4
3448.3
3560.2
3484.3
3496.5
3508.8
3521.1
3546.1
3558.7
3571.4
3584.2
3597.1
3610.1
3636.4
3649.6
3663.0
3676.5
3690.0
3703.7
3717.5
3731.3
3745.3
3759.4
3773.6
3787.9
3802.3
3816.8
3831.4
3846.2
3861.0
3876.0
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
229
229
228
227
227
226
226
225
224
224
223
222
222
221
221
220
220
219
218
218
217
217
216
216
215
215
214
214
213
212
212
211
211
210
210
209
209
208
4366.8
4366.8
4386.0
4405.3
4405.3
4424.8
4424.8
4444.4
4464.3
4464.3
4484.3
4504.5
4504.5
4524.9
4524.9
4545.5
4545.5
4566.2
4587.2
4587.2
4608.3
4608.3
4629.6
4629.6
4651.2
4651.2
4672.9
4672.9
4694.8
4717.0
4717.0
4739.3
4739.3
4761.9
4761.9
4784.7
4784.7
4807.7
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
3. A third, and even more expensive approach requires
the use of an additional crystal, or resonator.
INTERNAL CLOCK CALIBRATION
Timing-related functions on the 33977 (e.g., pointer,
velocities, acceleration, and Return to Zero Pointer speeds)
depend upon a precise, consistent time reference to control
the pointer accurately and reliably. Generating accurate time
references on an integrated circuit can be accomplished.
There are three methods to generate accurate time
references on an integrated circuit:
The internal clock in the 33977 is temperature
independent and area efficient; however, it can vary up to 70
percent due to process variation. Using the existing SPI
inputs and the precision timing reference already available to
the microcontroller, the 33977 allows more accurate clock
calibration to within ±10 percent without requiring extra pins,
components, or costly circuitry.
1. One option is trimming; however, timing tends to be
costly due to the large amount of die area required for
trim pads.
Calibrating the internal 1.0 MHz clock is initiated by writing
Logic [1] to PECCR bit PE3, illustrated in Figure 8.
2. Another, but expensive possibility is an externally
generated clock signal. This option requires a
dedicated pin on the device and controller.
Figure 8. Gauge Enable and Clock Calibration Example
fall below 1.0 MHz. The frequency range of the calibrated
clock is always below 1.0 MHz if PECCR bit PE4 is Logic [0]
prior to initiating a calibration command, followed by an 8.0 µs
reference pulse. The frequency is centered at 1.0 MHz if bit
D4 is written Logic [1].
The 8.0 µs calibration pulse is then provided by the
controller to result in a nominal internal 33977 clock speed of
1.0 MHz. The pulse is sent on the CS pin immediately after
the SPI calibration command is sent. During the calibration,
The 33977 can be fooled into calibrating faster or slower
than the optimal frequency by sending a calibration pulse
longer or shorter than the intended 8.0 µs. As long as the
calibration divisor remains between four and 15 there is no
calibration flag. For applications requiring a slower calibrated
clock, e.g., a motor designed with a gear ratio of 120:1
(8 microsteps/deg), users will have to provide a longer
calibration pulse. The internal oscillator can be slowed with
the PECCR command, so the calibration divisor safely falls
within the four to 15 range when calibrating with a longer time
reference. Fro example, for the 120:1 motor, the pulse would
be 12 µs instead of 8.0 µs. The result of this slower calibration
is longer step times resulting in generating pointer
no other SPI lines should be toggled. At the moment the CS
pin transitions from Logic [1] to Logic [0], an internal 7-bit
counter counts the number of cycles of an internal, 8.0 MHz
clock. The counter stops when the CS pin transitions from
Logic [0] to Logic [1]. The value in the counter represents the
number of cycles of the 8.0 MHz clock occurring in the 8.0 µs
window; it should range from 32 to 119. An offset is added to
this number to help center, or skew, the calibrated result to
generate a desired maximum, or normal frequency. The
modified counter value is truncated by four bits to generate
the calibration divisor, potentially ranging from four to 15. The
8.0 MHz clock is divided by the calibration divisor, resulting in
a calibrated 1.0 MHz clock. If the calibration divisor lies
outside the range of four to 15, the 33977 flags the CAL bit in
the device Status register, indicating the calibration
movements capable of meeting acceleration and velocity
requirements. The resolution of the pointer positioning
decreases from 0.083 deg/microstep (180:1) to 0.125
deg/microstep (120:1) while the pointer sweep range
increases from approximately 340° to over 500°.
procedure was not successful. A clock calibration is allowed
only if the gauge is disabled, or the pointer is not moving as
indicated by the Status bit of MOV, illustrated in Table 16
section of this document.
Note: A fast calibration could result in violations of the
motor acceleration and a velocity maximums, resulting in
missed steps.
Some applications may require a guaranteed maximum
pointer velocity and acceleration. Guaranteeing these
maximums requires the nominal internal clock frequency to
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
16
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
position step values as the pointer decelerates. The default
movement in the 33977 uses this ramp modification feature.
An example is illustrated in Figure 9. If the maximum
acceleration and deceleration of the pointer is desired, the
repetitive steps can be disabled by writing Logic [1] to the
PECCR bit PE5.
POINTER DECELERATION
Constant acceleration and deceleration of the pointer
produces relatively choppy movements when compared to
those of an air core gauge. Modification of the velocity
position ramp during deceleration can create the desired
damped movement. This modification is accomplished in the
33977 by adding repetitive steps at several of the last velocity
.
Velocity
Position
24
24
23
23
22
22
21
20
21
20
19
18
17
16
15
14
13
12
11
10
19
18
17
16
15
14
13
12
11
10
Hold Counts
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
=
0
Position
0
Microsteps
Figure 9. Deceleration Ramp
determines an RTZ sequence is not working properly, for
example, the RTZ taking too long; it can disable the
command via the RTZR bit RZ1. [Altered for better read flow]
RETURN TO ZERO CALIBRATION
Many stepper motor applications require [that deleted as
PV] the IC detect when the stepper motor stalls after
commanded to return to the zero position for calibration
purposes. In instrumentation applications, the stalling occurs
when the pointer hits the end stop on the gauge bezel,
[which is deleted as PV] usually at the zero position. It is
important to know [that PV] when the pointer reaches the end
stop, it immediately stops without bouncing away. The 33977
device provides the ability to automatically and independently
return the pointer to the zero position via the RTZR and
RTZCR SPI commands. An automatic RTZ is initiated, using
the RZ1 and RZ2 bits, provided the RZ4 is Logic [1]. During
an RTZ event, all commands related to the gauge being
returned are ignored until the pointer has successfully
zeroed, or the RTZR bit RZ1 is written to disable the event.
Once an RTZ event is initiated, the device reports back via
the SO pin an RTZ event is underway.
RTZCR bits RC10:RC5 are written to preload the
accumulator with a predetermined value assuring accurate
pointer stall detection. This preloaded value can be
determined during application development by disabling the
automatic shutdown feature of the device with the RTZR bit
RZ4. This operating mode allows the master to monitor the
RTZ event, using the accumulator information available via
the SO if the device is configured to provide the RTZ
Accumulator Status. The unconditional RTZ event can be
turned OFF using the RTZR bit RZ1.
If the Position 0 location bit, RZ2, is in the default Logic [0]
mode, then during an RTZ event the pointer is returned
counterclockwise (CCW) using full steps at a constant speed
determined by the RTZCR RC3:RC0 and RC12:RC11 bits
written during RTZ configuration, see Figure 10. Full steps
are used during an RTZ so only coil of the motor is being
driven at any time. The coil not being driven is used to
determine if the pointer is moving. If the pointer is moving, the
flux present in the non-driven coil is processed by integrating
the back EMF signal present on the opened pin of the coil
while applying a fixed potential to the other end.
The RTZCR command is used to set the RTZ pointer
speed, choose an appropriate blanking time, and preload the
integration accumulator with an appropriate offset. On
reaching the end stop, the device reports back to the
microcontroller via the status message [that PV] the RTZ was
successful. The RTZ automatically disables, [that will PV]
allowing other commands to be valid. In the event the master
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
IMAX
+
0
ICOIL
SINE
_
IMAX
0
1
2
3
0
I
MAX
COSINE
+
ICOIL
0
_
IMAX
0
1
2
3
0
Figure 10. Full Steps (Counterclockwise)
The IC automatically prepares the non-driven coil at each
step, waits for a predetermined blanking time, and then
processes the signal for the duration of the full step. When
the pointer reaches the stop and not longer moves, the
dissipating flux is detected. The processed results are placed
in the RTZ accumulator, and then compared to a decision
threshold. If the signal exceeds the decision threshold, the
pointer is assumed to be moving. If the threshold value is not
exceeded, the drive sequence is stopped if RTZR bit RZ4 is
Logic [0]. If bit RZ4 is Logic [1], the RTZ movement will
continue indefinitely until the RTZR bit RZ1 is used to stop the
RTZ event.
held constant. The full steps are evenly spaced, resulting in
equidistant movement as the motor is full stepped.
In comparison, motors [that have deleted PV] whose coils
aligned at a 60° angle [will deleted PV] results in two distinct
flux values as a the coils are driven in the same full step
fashion. This lack of symmetry in the measured flux is due to
the difference in the electrical angles between full steps.
Clearly stated, the distance the rotor moves changes from full
step to full step. This difference can be observed in Figure 7
and Table 5.
In Figure 7, where PE6 = 0, the difference in microsteps
between alternating full steps (one coil at maximum current
while the other is at zero) is always six. In contrast, the same
figure illustrates PE6 = 1 showing the difference in
microsteps between full steps of the 60° coils alternating
between four and eight. These expected differences should
be taken into account when setting the RTZ threshold.
A pointer [that is PV] not on a full step location, or [that
PV] is in magnetic alignment prior to the RTZ event may
cause a false RTZ detection. More specifically, an RTZ event
beginning from a non-full step position may result in an
abbreviated flux value potentially interpreted as a stalled
pointer. Advancing the pointed by at least 12 microsteps
clockwise (if PE7 = 0) to the nearest full step position (e.g., 0,
6, 12, 18, 24, etc.) prior to initiating an RTZ ensures the
magnetic fields line up and increases the chances of a
successful pointer stall detection. It is important that the
pointer be in a static, or commanded, position before starting
the RTZ event. Because the time duration and the number of
steps the pointer moves prior to reaching the commanded
position can vary depending upon its status at the time a
position change is communicated, the master should make
sure that the rotor is not moving prior to starting an RTZ.
Cessation of movement can be inferred by monitoring the
CMD and/or the MOV status bits.
After completion of an RTZ, the 33977 automatically
assigns the zero step position to the full step position at the
end-stop location. Because the actual zero position could lie
anywhere within the full step where the zero was detected,
the assigned zero position could be within a window of ±0.5°.
An RTZ can be used to detect stall, even if the pointer rests
on the end-stop when RTZ sequence is initiated. However, it
is recommended to advance the pointer by at least 12
microsteps to the nearest full step prior to initiating the RTZ.
RTZ OUTPUT
During an RTZ event the non-driven coil is analyzed to
determine the state of the motor. The 33977 multiplexes the
coil voltages, [chgd PV and provides to read as active voice]
providing signal from the non-driven coil to the RTZ pin.
It should be pointed out, the flux value, for an ideal motor
with the coils perfectly aligned at 90°, will vary little from full
step to full step if all other variables, such as temperature, are
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
18
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
continues to be set until the gauge is successfully re-enacted,
provided the junction temperature has fallen below the
hysteresis level.
DEFAULT MODE
Default mode refers to the state of the 33977 after an
internal or external reset prior to SPI communication. An
internal reset occurs during VDD power-up or if VPWR falls
below 4.0 V. An external reset is initiated by the RST pin
driven to Logic [0]. With the exception of the RTZCR full step
time, all of the specific pin functions and internal registers will
operate as though all of the addressable configuration
register bits were set to Logic [0]. This means, for example,
[deleted PV that] the outputs will be disabled after a power-
up or external reset, and SO flag OD6 and OD8 are set,
indicating an undervoltage event. Anytime an external reset
is exerted and the default is restored, all configuration
parameters [replaced e.g. with such as] such as clock
calibration, maximum speed, and RTZ parameters are lost
and must be reloaded.
OVERVOLTAGE FAULT REQUIREMENTS
The device is capable of surviving VPWR voltages within
the maximum specified in Maximum Ratings, Table 2. VPWR
levels resulting in an overvoltage shutdown condition can
result in uncertain pointer positions. Therefore, the pointer
position should be re-calibrated. The master will be notified of
an overvoltage event via the SO pin if the device status is
selected. Overvoltage detection and notification occurs
regardless of whether the gauge(s) are enabled or disabled.
OVERCURRENT FAULT REQUIREMENTS
Outcome currents are limited to safe levels allowing the
device to rely on thermal shutdown to protect itself.
FAULT LOGIC REQUIREMENTS
The 33977 device indicates each of the following faults as
they occur:
UNDERVOLTAGE FAULT REQUIREMENTS
Undervoltage VPWR conditions may result in uncertain
pointer positions. Therefore, the internal clock and the pointer
position may require re-calibration. The state machine
continues to operate with VPWR voltage levels as low as 4.0
V; however, the coil voltages may be clipped. Notification of
an undervoltage event is provided via the SO pin.
• Overtemperature fault
• Undervoltage VPWR
• Overvoltage VPWR
• Clock Out of Specification [Formalized spec]
These fault bits remain enabled until they are clocked out
of the SO pin with a valid SPI message.
RESET (SLEEP MODE)
Overcurrent faults are not reports directly; however, it is
likely an overcurrent condition will become a thermal issue
and be reported.
The device can reset internally or externally. If the VDD
level falls below the VDDUV level, the device resets and
powers up in the Default mode. See Static Electrical
Characteristics table under the sub-heading: Power Input in
Table 3. Similarly, if the RST pin is driven to Logic [0], then
the device resets to its default state. The device consumes
the least amount of current (IDD and IPWR) when the RST pin
is Logic [0]. This is also referred to as the Sleep mode.
OVERTEMPERATURE FAULT REQUIREMENTS
The 33977 incorporates overtemperature protection
circuitry, shutting off the gauge driver when an excessive
temperature is detected. In the event of a thermal overload,
the gauge driver is automatically disabled and the fault is
flagged via the OT device status bit. The indicating flag
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
Figure 11 and Figure 12. [figure numbers changed due to
SPI PROTOCOL DESCRIPTION
template formatting]
The SPI interface has a full-duplex, three-wire
synchronous,16-bit serial synchronous interface data
transfer and four I/O lines associated with it: Chip Select
(CS), Serial Clock (SCLK), Serial Input (SI), and Serial Output
(SO). The SI/SO pins of the 33977 follow a first in/first out
(D15/D0) protocol with both input and output words
transferring the most significant bit first. All inputs are
compatible with 5.0 V CMOS logic levels.
It transitions one time per bit transferred at an operating
frequency, fSPI, defined in the SPI Interface Timing section of
the Dynamic Electrical Characteristics Table 4. It is idle
between command transfers. The pin is 50 percent duty
cycle, with CMOS logic levels. This signal is used to shift data
to and from the device.
SERIAL OUTPUT (SO)
CHIP SELECT (CS)
The SO data pin is a tri-stateable output from the Shift
register. This output will remain tri-stated unless the device is
selected by a low CS signal. The output signal generated will
have CMOS logic levels and the output will transition on the
rising edges of SCLK. The serial output data provides status
feedback and fault information for each output and is returned
MSB first when the device is addressed.
The CS pin enables communication with the master
device.
When this pin is in a Logic [0] state, the 33977 is capable
of transferring information to, and receiving information from,
the master. The 33977 latches data in from the Input Shift
registers to the addressed registers on the rising edge of CS.
The output driver on the SO pin is enabled when CS is Logic
[0]. When CS is logic high, signals at the SCLK and SI pins
are ignored and the SO pin is tri-stated (high impedance). CS
will only be transitioned from a Logic [1] state to a Logic [0]
The Status register bits are the first 16 bits shifted out.
Those bits are followed by the message bits clocked in FIFO,
when the device is in a daisy chain connection, or being sent
words [that are deleted as PV] multiples of 16 bits. Data is
shifted on the rising edge of the SCLK signal. The SO pin
[will deleted as PV] remains in a high impedance state until
the CS pin is put into a logic low state.
state when SCLK is Logic [0]. CShas an internal pull-up (IUP
)
connected to the pin, as specified in the section of the Static
Electrical Characteristics table entitled CONTROL I/O,
[which is found on page...deleted for consistent format]
Table 3. This pin is also used to calibrate the internal clock.
SERIAL INPUT (SI)
The SI pin is the input of the SPI. This input has an internal
active pull-down requiring CMOS logic levels. The serial data
transmitted on this line is a 16-bit control command sent MSB
first, controlling the gauge functions. The master ensures
data is available on the falling edge of SCLK.
SERIAL CLOCK (SCLK)
SCLK clocks the Internal Shift registers of the 33977
device. The SI pin accepts data into the Input Shift register on
the falling edge of the SCLK signal, while the Serial Output
pin (SO) shifts data information out of the SO line driver on
the rising edge of the SCLK signal. It is important the SCLK
pin be in a Logic [0] state whenever the CS makes any
transition. SCLK has an internal pull-down (lDWN), as
specified in the section Control I/O of the Static Electrical
Characteristics, [which is found on page...deleted for
consistent format] Table 3. When CS is Logic [1], signals at
the SCLK and SI pins are ignored and SO is tri-stated (high
impedance). Refer to the data transfer timing diagrams in
Serial input information is read on the falling edge of
SCLK. A 16-bit stream of serial data is required on the SI pin,
beginning with the most significant bit (MSB). Messages [that
are deleted as PV] not multiples of 16 bits (e.g., daisy
chained device messages) are ignored. After transmitting a
16-bit word, the CSpin must be de-asserted (Logic [1]) before
transmitting a new word. SI information is ignored when CS
is in a logic high state.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
20
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
This section provides a description of the 33977 SPI
behavior. To follow the explanation below, please refer to
Table 7 and to the timing diagrams illustrated in Figure 11
and Figure 12.
Table 7. Data Transfer Timing
Pin
Description
CS (1-to-0)
CS (0-to-1)
SO
SO pin is enabled
33977 configuration and desired output states are transferred and executed according to the data in the Shift registers
Will change state on the rising edge of the SCLK pin signal
SI
Will accept data on the falling edge of the SCLK pin signal
CS
Output Shift register is loaded here
Note: SO is tri-stated when CS is Logic [1]
Figure 11. Single 16-Bit Word SPI Communication
CS
SCLK
SI
D2
D12 D11
0D12 OD
SO
Notes:
1. SO is tri-stated when CS is Logic [1].
2. D15, D14, D13, , and D0 refer to the first 16 bits of data into the 33977.
3. D15*, D14*, D13*,. . . ., and D0* refer to the most recent entry of program data into the 33977.
4. OD15, OD14, OD13, . . .,and OD0 refer to the first 16 bits of fault and status data out of the 33977.
Figure 12. Multiple 16-Bit Word SPI Communication
DATA INPUT
DATA OUTPUT
The Input Shift register captures data at the falling edge of
the SCLK. The SCLK pulses exactly 16 times only inside the
transmission windows (CS in a Logic [1] state). By the time
the CS signal goes to Logic [1] again, the contents of the
Input Shift register are transferred to the appropriate internal
register addressed in bits 15:13. The minimum time CS
should be kept high depends on the internal clock speed,
specified in the SPI Interface Timing section of the [Static
replaced with Dynamic - correcting table location] Dynamic
Electrical Characteristics, Table 4. It must be long enough so
the internal clock is able to capture the data from the Input
Shift register and transfer it to the internal registers.
At the first rising edge of the SCLK [clock deleted to
eliminate redundancy], with CS at Logic [1], the contents of
the selected Status Word register are transferred to the
Output Shift register. The first 16 bits clocked out are the
status bits. If data continues to clock in before the CS
transitions to Logic [1], the device begins to shift out the data
previously clocked in FIFO after the CS first transitioned to
Logic[1].
COMMUNICATION MEMORY MAPS AND
REGISTER DESCRIPTIONS
The 33977 device is capable of interfacing directly with a
microcontroller via the 16-bit SPI protocol specified below.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
The device is controlled by the microprocessor and reports
back status information via the SPI. This section provides a
detailed description of all registers accessible via serial
interface. The various registers control the behavior of this
device.
• Battery overvoltage
• Battery undervoltage
• Pointer zeroing status
• Internal clock status
• Confirmation of pointer movement commands
• Real time pointer position information
• Real time pointer velocity step information
• Pointer movement direction
• Command pointer position status
• RTZ accumulator value
A message is transmitted by the master beginning with the
MSB (D15) and ending with the LSB (D0). Multiple messages
can be transmitted in succession to accommodate those
applications where daisy chaining is desirable, or to confirm
transmitted data, as long as the messages are all multiples of
16 bits. Data is transferred through daisy-chained devices, as
illustrated in Figure 12. If an attempt is made to latch in a
message smaller than 16 bits wide, it is ignored.
REGISTER DESCRIPTIONS
The following section describes the registers, their
addresses, and their impact on device operation.
Table 8 lists the five registers the 33977 uses to configure
the device, control the state of the [Chgd to two per D.
Mortensen] two H-bridge outputs, and determine the type of
status information [that is deleted PV] clocked back to the
master. The registers are addressed via D15:D13 of the
incoming SPI word.
ADDRESS 000 - POWER, ENABLE, CALIBRATION,
AND CONFIGURATION REGISTER (PECCR)
The Power, Enable, Calibration, and Configuration
Register is illustrated in Table 9. A write to the 33977 using
this register allows the master to:
Table 8. Module Memory Map
Address
• Enable or disable the output drivers of the gauge
controller
• Calibrate the internal clock
Register
Name
See
[15:13]
000
Power, Enable, Calibration, and
Configuration Register
PECCR
Table
9
• Disable the air core emulation
• Select the direction of the pointer movement during
pointer positioning and zeroing
• Configure the device for the desired status information
to be clocked out into the SO pin, or
• Send a null command for the purpose of reading the
status bits.
001
010
Maximum Velocity Register
VELR
POSR
Table
10
Gauge Position Register
Table
11
011
100
Not Used
–
–
This register is also used to place the 33977 into a low
current consumption mode.
Return to Zero Register
RTZR
Table
12
The gauge drivers can be enabled by writing Logic [1] to
the assigned address bits, PE0. This feature could be used
to disable a driver if it is failing. The device can be placed into
a standby current mode by writing Logic [0] to PE0. During
this state, most current consuming circuits are biased off.
When in the Standby mode, the internal clock will remain ON.
101
Return to Zero Configuration
Register
RTZCR
Table
13
110
111
Not Used
RMPSELR
–
–
–
Reserved for Test
The internal state machine utilizes a ROM table of step
times defining the duration that the motor will spend at each
microstep as it accelerates or decelerates to a commanded
position. The accuracy of the acceleration and velocity of the
motor is directly related to the accuracy of the internal clock
Although the accuracy of the internal clock is temperature
independent, the non-calibrated tolerance is +70% to -35%.
The 33977 was designed with a feature allowing the internal
clock to be software calibrated to a tighter tolerance of ±10%,
using the CS pin and a reference time pulse provided by the
microcontroller.
[The word Zero omitted above in 101 my error]
MODULE MEMORY MAP
Various registers of the 33977 SPI module are addressed
by the three MSBs of the 16-bit word received serially.
Functions to be controlled include:
• Individual gauge drive enabling
• Power-up/down
• Internal clock calibration
• Gauge pointer position and velocity
• Gauge pointer zeroing
Calibration of the internal clock is initiated by writing Logic
[1] to PE3. The calibration pulse, which must be 8.0 µs for an
internal clock speed of 1.0 MHz, will be sent on the CS pin
immediately after the SPI word is sent. No other SPI lines will
be toggled. A clock calibration will be allowed only if the
gauge is disabled or the pointer is not moving, as indicated
• Air core motor movement emulation
• Status information
Status reporting includes:
• Individual gauge overtemperature condition
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
by status bits MOV0. Additional details are provided in the
Internal clock Calibration section.
Similarly, this bit must always be written as Logic [1] when
being used to control Switec style motors.
Some applications may require a guaranteed maximum
pointer velocity and acceleration. Guaranteeing these fall
below 1.0 MHz. The frequency range of the calibrated clock
maximums requires [that deleted PV] the nominal internal
clock frequency will always be below 1.0 MHz if bit PE4 is
Logic [0] when initiating a calibration command, followed by
an 8.0 µs reference pulse. The frequency will be centered at
1.0 MHz if bit PE4 is Logic [1]. Some applications may require
a slower calibrated clock due to a lower motor gear reduction
ratio. Writing Logic [1] to bit PE2 will slow the internal
oscillator by one-third. Slowing the oscillator accommodates
a longer calibration pulse without overrunning the internal
counter - a condition designed to generate a CAL fault
indication. For example, calibration for a clock frequency of
667 kHz would require a calibration pulse of 12 µs. Unless the
internal oscillator is slowed by writing PE2 to Logic [1], a 12
µs calibration pulse may overrun the counter and generate a
CAL fault indication.
The default Pointer Position 0 (PE7 = 0) will be the farthest
counter-clockwise position. A Logic [1] written to bit PE7 will
change the location of the position 0 for the gauge to the
farthest clockwise position. The pointer will always move
towards position 0 when executing an RTZ. Exercise care
when writing to PECCR bit PE7 in order to prevent an
accidental change of the position 0 location.
Bits PE11:PE9 determine the content of the bits clocked
out of the SO pin. When bit PE11 is at Logic [0], the clocked
out bits will provide device status. If Logic [1] is written to bit
PE11, the bits clocked out of the SO pin, depending upon the
state of bits PE10:PE9, provides either:
• Accumulator information and detection status during
the RTZ (PE10 Logic [0])
• Real time pointer position location at the time CS goes
low (PE10 Logic [1] and PE9 Logic [0]), or
• The real time step position of the pointer as described
in the velocity Table 6 (PE10 and PE9 Logic [1]).
Some applications may require faster pointer positioning
than is provided with the air core motor emulation feature.
Writing Logic [1] to bit PE5 will disable the air core emulation
for both gauges and provide an acceleration and deceleration
at the maximum that the velocity position ramp can provide.
Bit PE6 must always be written Logic [0] during all PECCR
writes if the device is being used to drive an MMT style motor.
Additional details are provided in the SO Communication
section.
If bit PE12 is Logic [1] during a PECCR command, the
state of PE11:PE0 is ignored. This is referred to as the null
command and can be used to read device status without
affecting device operation.
Table 9. Power, Enable, Calibration, and Configuration Register (PECCR)
Address 000
Bits
D12
–
D11
–
D10
–
D9
–
D8
–
D7
–
D6
–
D5
–
D4
–
D3
–
D2
–
D1
–
D0
–
Read
Write
PE12
PE11
PE10
PE9
0
PE7
PE6
PE5
PE4
PE3
PE2
0
PE0
Pointer Position or Pointer Speed Select (PE9) Bit D9
The bits in Table 9 are write-only.
This bit is recognized only if PE11 and PE10 = 1.
Null Command for Status Read (PE12) Bit D12
• 0 = Gauge Pointer Position
• 1 = Gauge Pointer Speed
• 0 = Disable
• 1 = Enable
(PE8) Bit D8
Status Select (PE11) Bit D11
This bit must be transmitted as Logic [0] for valid PECCR
commands.
This bit selects the information clocked out of the SO pin.
• 0 = Device Status (the logic states of PE10, and PE9
are don’t cares)
Position 0 Location Select (PE7) Bit D7
• 1 = RTZ Accumulator Value, Gauge Pointer position, or
Gauge Velocity ramp position (depending upon the
logic states of PE10, and PE9)
This bit determines the Position 0 of the gauge. RTZ
direction will always be to the position 0.
• 0 = Position 0 is the most CCW (counterclockwise)
position
• 1 = Position 0 is the most CW (clockwise) position
RTZ Accumulator or Pointer Status Select (PE10) Bit D10
This bit is recognized only when PE11 = 1.
Motor Type Selection (PE6) Bit D6
• 0 = RTZ Accumulator Value and status
• 1 = Pointer Position or Speed
• 0 = MMT Style (coil phase difference = 90°)
• 1 = Switec Style (coil phase difference = 60°)
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Air Core Motor Emulation (PE5) Bit D5
Gauge Enable (PE0) Bit D0
This bit is enabled or disabled (acceleration and
deceleration is constant if disabled).
This bit enables or disables the output drivers of the
Gauge.
• 0 = Enable
• 1 = Disable
• 0 = Disable
• 1 = Enable
Clock Calibration Frequency Selector (PE4) Bit D4
ADDRESS 001 - MAXIMUM VELOCITY REGISTER
(VELR)
• 0 = Maximum f =1.0 MHz (for 8.0 µs calibration pulse)
• 1 = Nominal f =1.0 MHz (for 8.0 µs calibration pulse)
The Gauge Maximum Velocity Register is used to set a
maximum velocity for the gauge (refer to Table 4). Bits V7:V0
contain a position value from 1 - 225 representative of the
velocity position value described in the Velocity Table,
Table 6. The table value becomes the maximum velocity until
it is changed to another value. If a maximum value is chosen
that is greater than the maximum velocity of the acceleration
Clock Calibration Enable (PE3) Bit D3
This bit enables or disables the clock calibration.
• 0 = Disable
• 1 = Enable
table, the maximum table value becomes the maximum
velocity.
Oscillator Adjustment (PE2) Bit D2
• 0 = tCLU
• 1 = 0.66 x tCLU
If the motor is turning at a speed greater than the new
maximum, the motor immediately moves down the velocity
ramp until the speed falls equal to or below it. Bit V8 must be
written to a Logic [1] when changing the maximum velocity of
the motor. Bits V12:V10 must be at Logic [0] for valid VELR
commands.
(PE1) Bit D1
This bit must be transmitted as Logic [0] for valid PECCR
commands
.
Table 10. Maximum Velocity Register (VELR)
Address 001
Bits
D12
–
D11
–
D10
–
D9
–
D8
–
D7
–
D6
–
D5
–
D4
–
D3
–
D2
–
D1
–
D0
–
Read
Write
0
0
0
0
V8
V7
V6
V5
V4
V3
V2
V1
V0
(V7:V0) Bits D7:D0
The bits in Table 10 are write-only.
These bits can be used to program the device to limit the
maximum velocity of the pointer movement. to one of over
200 speeds listed in the Velocity Table 6. This velocity will
remain the maximum of the intended gauge until changed by
command. Velocities can range from position 1 (00000001)
to position 225 (11111111).
(V12:V9) Bits D12:D9
These bits must be transmitted as Logic [0] for valid VELR
commands.
Gauge Velocity (V8) Bit D8
Enables the maximum velocity as determined in the V7:
V0.
ADDRESSES 010 - GAUGE POSITION REGISTER
(POSR)
• 0 = Velocity change disabled
• 1 = Velocity change enabled
SI Address 010 (Gauge Position Register) register bits
PO11: PO0 are written to when communicating the desired
pointer positions. Commanded positions can range from 0 to
4095
Table 11. Gauge Position Register (POSR)
Address 010
Bits
D12
–
D11
–
D10
–
D9
–
D8
–
D7
–
D6
–
D5
–
D4
–
D3
–
D2
–
D1
–
D0
–
Read
Write
0
P011
P010
P09
P08
P07
P06
P05
P04
P03
P02
P01
P00
The bits in Table 11 are write-only.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
24
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
PO012 (D12)
steps, where only one coil is driven at any point in time. The
back electromotive force (EMF) signal present on the non-
driven coil is integrated and its results are stored in an
accumulator. A Logic [1] written to bit RZ1 enables a Return
to Zero for the Gauge if RZ0 is Logic [0]. A Logic [0] written to
This bits must be transmitted as Logic [0] for valid POSR
commands.
P011:P00 (D11:D0)
bit RZ1 disables a Return to Zero for the Gauge when RZ0 is
Logic [0].
Desired pointer position of Gauge. Pointer positions can
range from 0 (000000000000) to position 4095
(111111111111). For a stepper motor requiring 12
microsteps per degree of pointer movement, the maximum
pointer sweep is 341.25° (4095 ÷ 12).
Bits D12:D5 and D3:D2 must be written Logic [0] for valid
RTZR commands. An unconditional RTZ event can be
enabled or disabled with Bit RZ4. Writing Logic [0] results in
a typical RTZ event, automatically providing a Stop when a
stall condition is detected. A Logic [1] will result in RTZ
movement, causing a Stop if a Logic [0] is written to bit RZ0.
This feature is useful during development and
ADDRESS 100 - GAUGE RETURN TO ZERO
REGISTER (RTZR)
Gauge Return to Zero Register (RTZR), Table 12 below,
is written to return the gauge pointers to the zero position.
During an RTZ event, the pointer is returned to zero using full
characterization of RTZ requirements.
Table 12. Gauge Return to Zero Register (RTZR)
Address 100
Bits
D12
–
D11
–
D10
–
D9
–
D8
–
D7
–
D6
–
D5
–
D4
–
D3
–
D2
–
D1
–
D0
–
Read
Write
0
0
0
0
0
0
0
0
RZ4
0
RZ2
RZ1
0
(RZ0) Bit D0
Return to Zero Enable. This bit must always be written
Logic [0].
The register bits in Table 12 are write-only.
(RZ12:RZ5) Bits D12:D5
These bits must be transmitted as Logic [0] for valid
commands.
ADDRESS 101 - GAUGE RETURN TO ZERO
CONFIGURATION REGISTER
(RZ4) Bit D4
Gauge Return to Zero Configuration Register (RTZCR) is
used to configure the Return to Zero Event, Table 13. It is
written to modify the: [listed as bullets for reading ease]
This bit is used to enable an unconditional RTZ event.
• 0 = Automatic Return to Zero
• 1 = Unconditional Return to Zero
• Step time, or rate at which the pointer moves during an
RTZ event
• Integration blanking time, which is the time immediately
following the transition of a coil from a driven state to an
open state in the RTZ mode
(RZ3) Bit D3
This bit must be transmitted as Logic [0] for valid
commands.
• Threshold of the RTZ integration register
Values used for this register should be selected during
development to optimize the RTZ for each application.
Selecting an RTZ step rate resulting in consistently
successful zero detections depends on a clear understanding
of the motor characteristics. Specifically, resonant
frequencies exist due to the interaction between the motor
and the pointer. This command allows for the selection of an
RTZ pointer speed away from these frequencies. Also, some
motors require a significant amount of time for the pointer to
settle to a steady state position when moving from one full
step position to the next. Consistent and accurate integration
values require that the pointer be stationary at the end of the
full step time.
(RZ2) Bit D2
Return to Zero Direction bit. This bit is used to properly
sequence the integrator, depending upon the desired zeroing
direction.
• 0 = Return to Zero will occur in the CCW direction
(PE7 = 0)
• 1 = Return to Zero will occur in the CW direction
(PE7 =1)
(RZ1) Bit D1
Return to Zero Enable. This bit commands the gauge to
return the pointer to zero position.
Bits RC3:RC0, RC12:RC11, and RC4 determine the time
spent at each full step during an RTZ event. Bits RC3:RC0
are used to select a ∆t ranging from 0 ms (0000) to 61.44 ms
• 0 = Return to Zero Disabled
• 1 = Return to Zero Enabled
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
(1111) in increments of 4.096 ms (refer to Table 14). The ∆t
is multiplied by the factor M, defined by bits RC12:RC11. The
product is then added to the blanking time, selected using bit
RC4, to generate the full step time. The multiplier selected
with RC12:RC11 will be 1 (00), 2 (01), or 4 (10) as illustrated
in the equations below. Note that the RC12:RC11 value of 8
(11) is not recommended for use in a product design
application, because of the potential for an RTZ accumulator
internal overflow, due to the long time step. The blanking time
is either 512 µs when RC4 is Logic [0], or 768 µs when it is
Logic [1].The full step time is calculated using the following
equations:
and is compared to a threshold. Values above the threshold
indicate a pointer is moving. Values below the threshold
indicate a stalled pointer, thereby resulting in the cessation of
the RTZ event.
The RTZ accumulator bits are signed and represented in
two’s complement. After a full step of integration, a sign bit of
0 is the indicator of an accumulator exceeding the decision
threshold of 0, and the pointer is assumed to still be moving.
Similarly, if the sign bit is Logic [1] after a full step of
integration, the accumulator value is negative and the pointer
is assumed to be stopped. The integrator and accumulator
are initialized after each full step. If the PECCR command is
written to clock out the RTZ accumulator values via the SO,
the OD14 bit corresponds to the sign bit of the RTZ
accumulator.
When D3:D0 (RC3:RC0) = 0000
Full Step (t) = ∆t x M+ blanking (t)
(1)
When D3:D0 (RC3:RC0) = 0000
Accurate pointer stall detection depends on a correctly
preloaded accumulator for specific gauge, pointer, and full
step combinations. Bits RC10:RC5 are used to offset the
initial RTZ accumulator value, properly detecting a stalled
motor. The initial accumulator value at the start of a full step
of integration is negative. If the accumulator was correctly
preloaded, a free moving pointer will result in a positive value
at the end of the integration time, and a stalled pointer will
result in a negative value. The preloaded values associated
with each combination of bits RC10:RC5 are illustrated in
Table 15. The accumulator should be loaded with a value
resulting in an accumulator MSB to Logic [1] when the motor
is stalled. For the default mode, after a power-up or any reset,
the 33977 device sets the accumulator value to -1.
Full Step (t) = blanking (t) + 2.048 ms (2)
Note: In equation (2), a 2.048 ms offset is added to the full
step time when the RC3:RC0 = 0000. The full step time
default value after a logic reset is 12.80 ms (RC12:RC11 =
00, RC4 = 0, and RC3:RC0 = 0011).
If there are two full steps per degree of pointer movement,
the pointer speed is 1/(Full Step x 2) deg/s.
Detecting pointer movement is accomplished by
integrating the EMF present in the non-driven coil during the
RTZ event. The integration circuitry is implemented using a
Sigma-Delta converter resulting in the placement of a value
in the 15-bit RTZ accumulator at the end of each full step. The
value in the RTZ accumulator represents the change in flux
Table 13. Return to Zero Register Configuration Register (RTZCR)
Address 101
Bits
D12
–
D11
–
D10
–
D9
–
D8
–
D7
–
D6
–
D5
–
D4
–
D3
–
D2
–
D1
–
D0
–
Read
Write
RC12
RC11
RC10
RC9
RC8
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
The bits in Table 13 are write-only.
Values range from -1 (00000000) to -1009 (11111111) as
shown in Table 15, the default value = 000000.
(RC12:RC11) Bits D12:D11
(RC4) Bit D4
These bits, along with RC3:RC0 (D3:D0) and RC4 (D4),
determine the full step time and, therefore, the rate at which
the pointer will move during an RTZ event. The values of
D12:D11 determine the multiplier (M) used in equation (1)
(refer to the previous page).
This bit determines the RTZ blanking time (blanking (t)).
The default value = 0
• 0 = 512 µs
• 1 = 768 µs
RC12:RC11 = M; default value = 00
(RC3:RC0) Bits D3:D0
• 00 = 1
• 01 = 2
• 10 = 4
These bits, along with RC12:RC11 (D12:D11) and RC4
(D4), determine the time variables used to calculate the full
step times with equations (1) or (2) illustrated above.
RC3:RC0 determines the ∆t time. The ∆t values range from 0
(0000) to 61.440 ms (1111) and are shown in Table 14. The
default ∆t is 0 (0011).
• 11 = 8 (Not to be used for design)
(RC10:RC5) Bits D10:D5
These bits determine the value preloaded into the RTZ
integration accumulator to adjust the detection threshold.
Note: Equation (2) (refer to the preceding page) is only
used to calculate the full step time if RC3:RC0 = 0000. Use
equation (1) for all other combinations of RC3:RC0.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
26
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Table 14. RTZCR Full Step Time
Table 14. RTZCR Full Step Time
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
32.768
36.864
40.960
45.056
49.152
53.248
57.344
61.440
RC3
0
RC2
0
RC1
0
RC0
0
∆t (ms)
0.0
0
0
0
1
4.096
0
0
1
0
8.192
0
0
1
1
12.288
16.384
20.480
24.576
28.672
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
Table 15. RTZCR Accumulator Offset
RC10
RC9
RC8
RC7
RC6
RC5
Preload Value
Initial Accumulator Value = (-16xPV) -1
0
0
0
0
0
.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
.
0
1
0
1
0
.
0
1
2
3
4
.
-1
-17
-33
-49
-65
.
1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
1
1
1
1
63
-1009
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
PECCR command determines the nature of the status data
that is clocked out of the SO pin. There are four different
types of status information available:
SO COMMUNICATION
When the CS pin is pulled low, the internal status register,
as configured with the PECCR command bits PE11:PE8, is
loaded into the output register and the data is clocked out
MSB (OD15) first. Following a CS transition 0 to 1, the device
determines if the shifted-in message was of a valid length (a
valid message length is one that is greater than 0 bits and a
multiple of 16 bits) and, if so, latches the incoming data into
the appropriate registers. At this time, the SO pin is tri-stated
and the status register is now able to accept new status
information. Fault status information will be latched and held
until the Device Status Output register is selected and it is
clocked out via the SO. If the message length was
1. Device Status (Table 16)
2. RTZ Accumulator Status (Table 17)
3. Gauge Pointer Position Status (Table 18)
4. Gauge Pointer Velocity Status (Table 19)
Once a specific status type is selected, it will not change
until either the PECCR command bits PE11:PE8 (D11:D8)
are written to select another or the device is reset. Each of the
Status types and the PECCR bit necessary to select them ar
described in the following paragraphs.
determined to be invalid, the fault information will not be
cleared and will be transmitted again during the next valid SPI
message. Pointer status information bits (e.g., pointer
position, velocity, and commanded position status) will
always reflect the real time state of the pointer. Any bits
clocked out of the SO pin after the first 16 are representative
of the initial message bits clocked into the SI pin since the CS
pin first transitioned to a Logic [0]. This feature is useful for
daisy-chaining devices as well as message verification. As
described above, the last valid write to bits PE11:PE8 of the
DEVICE STATUS INFORMATION
Most recent valid PECCR command resulting in the Device
Status output:
D11
D10
D9
D8
0
x
x
x
x = Don’t Care
Table 16. Device Status Output Register
Bits
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD8
UV
–
OD7
OD6
OD5
OD4
OD3
ST3
–
OD2
OD1
ST1
–
OD0
OT
–
Read
Write
ST15
–
DIR
–
ST13 0POS ST11 CMD
OV
–
CAL OVUV ST5
MOV
–
RTZ
–
–
–
–
–
–
–
–
The bits in Table 16 are read-only bits.
• 0 = At commanded position
• 1 = Not at commanded position
(ST15) Bit OD15
Overvoltage Indication (OV) Bit OD9
This bit has no meaning.
A Logic [1] on this bit indicates VPWRvoltage exceeded the
upper limit of VPWROV since the last SPI communication.
Refer to the Static Electrical Characteristics Table 3 under
POWER INPUT.
(DIR) Bit OD14
This bit indicates the direction that the Gauge is moving.
• 0 = Toward position 0
An overvoltage event will automatically disable the driver
outputs. Because the pointer may not be in the expected
position, the master may want to re-calibrate the pointer
position with an RTZ command after the voltage returns to a
normal level. For an overvoltage event, both gauges must be
re-enabled as quickly as this flag returns to Logic [0]. The
state machine will continue to operate properly as long as
VDD is within the normal range.
• 1 = Away from position 0
(ST13) Bit OD13
This bit has no meaning.
(0POS) Bit OD12
This bit indicates the configured Position 0 for the Gauge.
• 0 = Normal range
• 1 = Battery voltage exceeded VPWROV
• 0 = Farthest CCW
• 1 = Farthest CW
Undervoltage Indication (UV) Bit OD8
(ST11) Bit OD11
A Logic [1] on this bit indicates the VPWR voltage fell below
VPWRUV since the last SPI communication. Refer to the Static
Electrical Characteristics Table 3 under the heading of
POWER INPUT. An undervoltage event is just flagged;
however, at some voltage level below 4.0 V, the outputs turn
OFF and the state machine resets. Because the pointer may
This bit has no meaning.
(CMD) Bit OD10
This bit indicates if the Gauge is at the most recently
commanded position.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
28
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
not be in the expected position, the master may want to re-
calibrate the pointer position with an RTZ command after the
voltage returns to a normal level. For an undervoltage vent,
both gauges may need to be re-enabled as quickly as this
flag returns to Logic [0]. The state machine will continue to
operate properly as long as VDD is within the normal range.
This bit may also be used to determine if the Gauge is
enabled or disabled.
• 0 = Gauge position has not changed since the last SPI
command
• 1 = Gauge pointer position has changed since the last
SPI command
• 0 = Normal range
• 1 = Battery voltage fell below VPWRUV
ST3 (OD3) - This bit has no meaning
Calibrated Clock out of Specification (CAL) Bit OD7
RTZ0 Is Enabled or Disabled (RTZ) Bit OD2
Reading Logic [1] on this bit indicates the clock count
calibrated to a value outside the expected range given the
tolerance specified by tCLC in the Dynamic Electrical
Characteristics Table 4 under POWER OUTPUT and
CLOCK TIMING.
A Logic [1] on this bit indicates the gauge is in the process
of returning to the zero position as requested with the RTZ
command. This bit continues to indicate Logic [1] until the SPI
message following a detection of the zero position, or the
RTZ feature is commanded OFF using the RTZ message.
• 0 = Clock within specification
• 1 = Clock out of specification
• 0 = Return to Zero disabled
• 1 = Return to Zero enabled successfully
Undervoltage or Overvoltage Indication (OVUV) Bit OD6
(ST1) Bit OD1
A Logic [1] on this bit indicates VPWR voltage fell to a level
below the VPWRUV since the last SPI communication. Refer
to the Static Electrical Characteristics table, Table 3 under
the subheading INPUT POWER. An undervoltage event is
just flagged, while an overvoltage event automatically
disables the drive outputs. Because the pointer may not be in
the expected position, the master may want to re-calibrate
the pointer with an RTZ command after the voltage returns to
normal level. For an overvoltage event, both gauges must be
re-enabled as soon as this flag returns to Logic [0]. The state
machine will continue to operate properly as long as VDD is
within the normal range.
This bit has no meaning.
Gauge Driver Junction Overtemperature (OT) Bit OD0
A Logic [1] on this bit indicates that the coil drive circuitry
has exceeded the maximum allowable junction temperature
since the last SPI communication and that the Gauge has
been disabled. It is recommended that the pointer be re-
calibrated using the RTZ command after re-enabling the
gauge using the PECCR command. This bit remains Logic [1]
until the gauge is re-enabled.
• 0 = Temperature within range
• 1 = Maximum allowable junction temperature condition
is reached
• 0 = Normal range
• 1 = Battery voltage fell below VPWRUV or exceeded
VPWROV
RTZ ACCUMULATOR STATUS INFORMATION
Most recent valid PECCR command resulting in the RTZ
Accumulator status output:
(ST5) Bit OD5
This bit has no meaning
D11
D10
D9
D8
Gauge Movement Since last SPI Communication (MOV)
Bit OD4
1
0
x
x
x = Don’t Care
A Logic [1] on this bit indicates the Gauge pointer position
has changed since the last SPI command. This information
allows the master to confirm the pointer is moving as
commanded.
[Used headings to distinguish bits and accompanying text.]
Table 17. RTZ Accumulator Status Output Register
Bits
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD8
OD7
OD6
OD5
OD4
OD3
OD2
OD1
OD0
Read
Write
RTZ ACC14 ACC13 ACC12 ACC11 ACC10 ACC9 ACC8 ACC7 ACC6 ACC5 ACC4 ACC3 ACC2 ACC1 ACC0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
The bits in Table 17 are read-only bits.
(RTZ) Bit OD15
RTZ Bit Is Enabled or Disabled. Reading Logic [1] on this
bit indicates that the Gauge is in the process of returning to
the zero position as requested with the RTZ command. This
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
bit will continue to indicate Logic [1] until the SPI message
following a detection of the zero position, or after the RTZ
feature is commanded OFF using the RTZ message.
The analog-to-digital converter's linear input range covers
the expected magnitude of motor back e.m.f. signals, which
is usually less than 500mV. Input signals greater than this will
not cause any damage (the circuit is connected to the motor
H-Bridge drivers, and thus is exposed to the full magnitude of
the drive voltages), but may cause some small loss of
linearity. A typical plot of output vs. input is shown in
Figure 13 for 4ms step times.
• 0 = Return to Zero disabled
• 1 = Return to Zero enabled successfully
[Corrected original entry above to ACC2]
(ACC14:ACC0) Bits OD14:OD0
These 15 bits are from the RTZ accumulator. They
represent the integrated signal present on the non-driven coil
during an RTZ event. These bits are Logic [0] after power-on
reset, or after the RST pin transitions from Logic [0] to [1].
After an RTZ event, they will represent the last RTZ
accumulator result before the RTZ was stopped.
GAUGE POINTER POSITION STATUS
INFORMATION
Most recent valid PECCR command resulting in the
Gauge Pointer Position status output:
ACC14 is the MSB and is the sign bit used for zero
detection. Negative numbers have MSB Logic [1] and are
coded in twos complement.
D11
D10
D9
D8
1
1
0
0
omitted “don’t care--because N/A
Figure 13. RTZ Accumulator (Typical)
Table 18. Gauge Pointer Position Status Output Register
Bits
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD8
OD7
OD6
OD5
OD4
OD3
OD2
OD1
OD0
Read
Write
ENB
–
DIR
–
DIRC CMD POS11 POS10 POS9 POS8 POS7 POS5 POS5 POS4 POS3 POS2 POS1 POS0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(DIRC) Bit OD13
The bits in Table 18 are read-only bits.
This bit is used to determine whether the direction of the
most recent pointer movement is toward the last commanded
position or away from it.
(ENB) Bit OD15
This bit indicates whether the Gauge is enabled.
• 0 = Direction of the pointer movement is toward the
commanded position
• 1 = Direction of the pointer movement is away from the
commanded position
• 0 = Disabled
• 1 = Enabled
(DIR) Bit OD14
This bit indicates the direction the Gauge is moving.
(CMD) Bit OD12
• 0 = Toward position 0
• 1 = Away from position 0
This bit indicates whether the gauge is at the most recently
commanded position.
• 0 = At commanded position
• 1 = Not at commanded position
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
30
FUNCTIONAL DEVICE OPERATION
(POS11:POS0) Bits OD11:OD0
D11
D10
D9
D8
These 12 bits represent the actual position of the pointer
at the time CS transitions to a Logic [0].
1
1
1
x
x = Don’t Care
GAUGE POINTER VELOCITY STATUS
INFORMATION
Most recent valid PECCR command resulting in the
Gauge and 1 Pointer Velocity status output:
Table 19. Gauge Pointer Velocity STatus Output Register
Bits
OD15 OD14 OD13 OD12 OD11 OD10 OD9
OD8
V8
–
OD7
V7
–
OD6
OD5
V5
–
OD4
OD3
V3
–
OD2
OD1
V1
–
OD0
V0
–
Read
Write
V15
–
V14
–
V13
–
V12
–
V11
–
V10
–
V9
–
V6
–
V4
–
V2
–
(V7:V0) Bits OD7:OD0
The bits in Table 19 are read-only bits.
These eight bits represent the step table value, [that
deleted PV] indicating the actual velocity step location (refer
to Table 19) of the Gauge pointer at the time that the CS
transitions to a Logic [0].
(V15:V8) Bits OD15:OD8
These eight bits have no meaning. Velocity position that
identifies it in the un-truncated ramp (e.g., if RS = 2, then the
velocity step location will be 3 when the pointer is at the
commanded position).
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
TYPICAL APPLICATIONS
TYPICAL APPLICATIONS
The 33977 is an extremely versatile device that can be
used in a variety of applications, Figure 1. The acceleration
and deceleration ramps have been designed for applications
where smooth movement is of the highest priority. These
ramps are fixed and the characteristics can be seen in the
following figures. For applications where configurable pointer
response and damping are desirable, consider the features
of the MC33976. Figure 14 shows the characteristics of the
acceleration ramp.
6000
5000
76ms
4000
Ideal
Acceleration
(4500 deg/s^2)
3000
2000
1000
0
MC33977
Acceleration
0
20000
40000
60000
80000
100000
120000
140000
160000
180000
TIME (us)
Figure 14. Acceleration Response Characteristics
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
32
TYPICAL APPLICATIONS
Figure 15 illustrates the deceleration damping characteristics of the device with the hold counts enabled and disabled.
1250
1200
1150
1100
1050
1000
950
MC33977
without
Hold Counts
MC33977
with
Hold Counts
900
850
800
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Time (s)
Figure 15. Deceleration Damping Response Examples
Table 20 provides a step-by-step example of configuring
and using many of the features designed into the IC This
example is intended to familiarize users with some of the
device features.
Table 20. 33977 Setup, Configuration, and Usage Example
Reference Table
and/or Figure
Step
Command
Description
a) Enables the gauge
Bit PE0: Gauge enable bit
•
b) Clock calibration
Table 9,
Figure 8
1
PECCR
•
•
Bit PE3: Enables calibration procedure
Bit PE4: Set clock f = 1.0 MHz maximum or nominal
c) Send 8.0 µs pulse on CS to calibrate 1.0 MHz clock
a) Set RTZ full step time
Table 13
Table 14
•
Bit RC3:RC0
b) Set RTZ blanking time
Bits RC4
c) Preload RTZ accumulator
Bits RC12:RC11 and RC10:RC5
d) Check SO for an out-of-range clock calibration
Is Bit CAL Logic [1}? If so, repeat Steps 1 and 2
Table 15
Table 9
•
2
RTZCR
Table 16
•
•
a) Move pointer to position 12 prior to RTZ
Table 11
Table 9
4
5
POSR
b) Check SO to determine if gauge has moved
Table 16
•
Is bit MOV (OD4) Logic [1]? If so, the gauge moved to the first microstep
a) Send null command to determine if gauges moved
Bit PE12
b) Check SO to determine if the gauge has moved
•
Table 9
Table 9
Table 16
PECCR
•
Is bit MOV (OD4) Logic [1]? If so, the gauge moved another microstep since the last
SPI message. Keep track of movement and if 12 steps are finished, and both gauges
are at a static position, the RTZ. Otherwise, repeat steps a) and b).
•
Bit CMD (OD10) could also be monitored to determine if the pointer is static.
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
TYPICAL APPLICATIONS
Table 20. 33977 Setup, Configuration, and Usage Example
Reference Table
and/or Figure
Step
Command
Description
a) Return the gauge to the zero stop using the RTZ command
•
•
Bit RZ1 enables or disables an RTZ
Bits RZ2 and PE7 select the direction
Table 12
Table 9
6
RTZ
b) Select the RTZ accumulator bits to clock out on the SO bits using bits PE11:PE10.
These will be used if characterizing the RTZ.
Table 15
a) Check the status of the RTZ by sending the null command to monitor bit RTZ of the
Device Status SO.
Table 9
Table 16
•
Bit PE12 is the null command
7
PECCR
VELR
b) Is RTZ (OD2) Logic [1]? If not, the gauge is still returning and null command should be
resent.
a) Change the maximum velocity of the gauge
•
•
Table 9
Table 6
Bit V8 enables a change to the maximum velocity
Bits V7:V10 determine the maximum velocity position from Table 6, Velocity Table
10
a) Position gauge pointer
Bits P011:P00: Desired pointer position
•
b) Check SO for out-of-range VPWR
•
Is bit OVUV (OD6) Logic [1] If so, use UV (OD8) and OV (OD9) to decide whether to
RTZ after valid VPWR
Table 11
Table 6
11
POSR
c) Check SO for overtemperature
•
Is bit OT Logic [1]? If so, enable driver again. If OT continues to indicate
overtemperature, shut down the gauge.
•
Once OT returns to normal, re-establish the zero reference by RTZ command.
a) Return the pointer close to zero position using POSR
13
15
POSR
Table 11
b) Move pointer position at least 12 microsteps CW to the nearest full step prior to RTZ
f) Send null command to see if gauges moved
•
Bit PE12
g) Check SO to determine if the gauge moved.
Table 9
Table 16
PECCR
•
Is bit MOV (OD4) Logic [1]? If so, the gauge moved another microstep since the last
SPI message. Keep track of movement and if 12 steps are finished, and both gauges
are at a static position, then RTZ. Otherwise, repeat steps a) and b).
•
Bit CMD (OD10) could also be monitored to determine the pointer is static.
a) Return the gauge to the zero stop using the RTZ command.
•
•
Bit RZ1 enables or disables an RTZ
Bits RZ2 and PE7 select the direction
TABLE 9
TABLE 12
TABLE 16
RTZ
16
b) Select the RTZ accumulator bits clocking out on the SO bits using bits PE11:PE10
These will be used if characterizing the RTZ.
a) Check the status of the RTZ by sending the null command to monitor SO bit RTZ
TABLE 9
TABLE 16
•
Bit PE12 is the null command
PECCR
PECCR
17
20
b) Is RTZ Logic [0]? If not, the gauge is still returning and null command should be resent
a) Disable the gauge driver and go to standby
•
Bit PE0:PE1 disable the gauge
b) Put the device to sleep
RST pin is pulled to Logic [0]
TABLE 9
•
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
34
PACKAGING
PACKAGE DIMENSIONS
PACKAGING
PACKAGE DIMENSIONS
For the most current revision of the package, visit www.freescale.com and do a keyword search using the “98A” number listed
below.
DW SUFFIX
EG SUFFIX (PB-FREE)
24-PIN
PLASTIC PACKAGE
98ASB42344B
ISSUE F
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
REVISION HISTORY
REVISION HISTORY
REVISION
1.0
DATE
8/2006
1/2007
DESCRIPTION OF CHANGES
• Initial release
• Updated to the current Freescale format
2.0
• Revised Internal Block Diagram to enhance readability
• Added parameter Peak Package Reflow Temperature During Reflow (4)
and notes (4) and (5)
,
(5) on page 4
• Made wording additions to Address 101 - Gauge Return to Zero Configuration Register
on page 25 and (RC12:RC11) Bits D12:D11 on page 26
,
• Added ADC Gain (12) (14) to Static Electrical Characteristics table
• Added RTZ Accumulator (Typical) on page 30 and accompanying text
33977
Analog Integrated Circuit Device Data
Freescale Semiconductor
36
How to Reach Us:
Home Page:
www.freescale.com
RoHS-compliant and/or Pb-free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
For information on Freescale’s Environmental Products program, go to http://
www.freescale.com/epp.
Tempe, Arizona 85284
+1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Semiconductor was negligent regarding the design or manufacture of the part.
Denver, Colorado 80217
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
© Freescale Semiconductor, Inc., 2007. All rights reserved.
MC33977
Rev. 2.0
1/2007
相关型号:
MC33981
High-Frequency, High-Current, Self-Protected High-Side Switch (4.0 mз up to 60 kHz)
MOTOROLA
©2020 ICPDF网 联系我们和版权申明