MCIMX31C_10_技术文档

Document Number: MCIMX31C

Rev. 4.3, 2/2010

Freescale Semiconductor

Data Sheet: Technical Data

MCIMX31C and

MCIMX31LC

Package Information

Plastic Package

Case 1931 19 x 19 mm, 0.8 mm Pitch

MCIMX31C and

MCIMX31LC

Multimedia Applications

Processors for Industrial and

Automotive Products

Ordering Information

See Table 1 on page 3 for ordering information.

Contents

1 Introduction

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Ordering Information . . . . . . . . . . . . . . . . . . . . . .3

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . .4

The MCIMX31C and MCIMX31LC multimedia

applications processors represent the next step in

low-power, high-performance application processors.

Unless otherwise specified, the material in this data sheet

is applicable to both the MCIMX31C and MCIMX31LC

processors and referred to singularly throughout this

document as MCIMX31C. The MCIMX31LC does not

include a graphics processing unit (GPU).

Functional Description and Application Information 4

ARM11 Microprocessor Core . . . . . . . . . . . . . . . .4

Module Inventory . . . . . . . . . . . . . . . . . . . . . . . . .6

Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . .9

Electrical Characteristics . . . . . . . . . . . . . . . . . . . . .9

Chip-Level Conditions . . . . . . . . . . . . . . . . . . . . .9

Supply Power-Up/Power-Down Requirements and

Restrictions . . . . . . . . . . . . . . . . . . . . . . . .15

Based on an ARM11™ microprocessor core, the

MCIMX31C provides the performance with low power

consumption required by modern digital devices such

as:

Module-Level Electrical Specifications . . . . . . . .16

Package Information and Pinout . . . . . . . . . . . . . .99

MAPBGA Production Package 473 19 x 19 mm,

0.8 mm Pitch . . . . . . . . . . . . . . . . . . . . . .100

•

Automotive infotainment and navigation

Industrial control (human interface)

Product Documentation . . . . . . . . . . . . . . . . . . . .106

Revision History . . . . . . . . . . . . . . . . . . . . . . . .107

The MCIMX31C takes advantage of the

ARM1136JF-S™ core running at 400 MHz, and is

optimized for minimal power consumption using the

most advanced techniques for power saving (DVFS,

power gating, clock gating). With 90 nm technology and

dual-Vt transistors (two threshold voltages), the

This document contains information on a new product. Specifications and information herein are subject to change without notice.

Introduction

MCIMX31C provides the optimal performance versus leakage current balance.

The performance of the MCIMX31C is boosted by a multi-level cache system, and features peripheral

devices such as an MPEG-4 Hardware Encoder (VGA, 30 fps), an Autonomous Image Processing Unit, a

Vector Floating Point (VFP11) co-processor, and a RISC-based SDMA controller.

The MCIMX31C supports connections to various types of external memories, such as DDR, NAND Flash,

NOR Flash, SDRAM, and SRAM. The MCIMX31C can be connected to a variety of external devices

using technology, such as high-speed USB2.0 OTG, ATA, MMC/SDIO, and compact flash.

1.1

Features

The MCIMX31C is designed for automotive and industrial markets where extended operating temperature

is required. They provide low-power solutions for high-performance demanding multimedia and graphics

applications.

The MCIMX31C is built around the ARM11 MCU core and implemented in the 90 nm technology.

The systems include the following features:

•

Multimedia and floating-point hardware acceleration supporting:

— MPEG-4 real-time encode of up to VGA at 30 fps

— MPEG-4 real-time video post-processing of up to VGA at 30 fps

— Video conference call of up to QCIF-30 fps (decoder in software), 128 kbps

— Video streaming (playback) of up to VGA-30 fps, 384 kbps

®

— 3D graphics and other applications acceleration with the ARM tightly-coupled Vector

Floating Point co-processor

— On-the-fly video processing that reduces system memory load (for example, the

power-efficient viewfinder application with no involvement of either the memory system or the

ARM CPU)

•

Advanced power management

— Dynamic voltage and frequency scaling

— Multiple clock and power domains

— Independent gating of power domains

•

Multiple communication and expansion ports including a fast parallel interface to an external

graphic accelerator (supporting major graphic accelerator vendors)

Security

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

2

Freescale Semiconductor

Introduction

1.2

Ordering Information

Table 1 provides the ordering information for the MCIMX31C.

1

Table 1. MCIMX31C and MCIMX31LC Ordering Information

Operating Temperature

2

Part Number

Silicon Revision

Package

Range (°C)

MCIMX31CVMN4C!

MCIMX31LCVMN4C!

MCIMX31CVMN4D!

MCIMX31LCVMN4D!

MCIMX31CJMN4C

MCIMX31LCJMN4D

MCIMX31CJMN4D

2.0

–40 to 85

2.0

2.0.1

19 x 19 mm,

0.8 mm pitch,

Case 1931

1

Because of an order from the United States International Trade Commission, BGA-packaged product lines

and part numbers indicated here currently are not available from Freescale for import or sale in the United

States prior to September 2010: Indicated by the Icon (!)

2

Case 1931 is RoHS compliant, lead-free, MSL = 3.

1.2.1

Feature Differences Between TO2.0 and TO 2.0.1

The following is a summary of the differences between silicon Revision 2.0 and Revision 2.0.1:

•

Revision 2.0.1 - iROM updated to support boot from USB HS and SD/MMC.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

3

Functional Description and Application Information

1.3

Block Diagram

Figure 1 shows the MCIMX31C simplified interface block diagram.

SDRAM

DDR

SRAM, PSRAM,

NOR Flash

NAND Flash,

SmartMedia

Parallel

Display (2)

Serial

LCD

Camera

Sensor (2)

Tamper

Detection

Mouse

Keyboard

AP Peripherals

AUDMUX

SSI (2)

External Memory

Interface (EMI)

MPEG-4

Video Encoder

Image Processing Unit (IPU)

Inversion and Rotation

Camera Interface

Power

Management

UART (5)

I²C (3)

FIR

Blending

IC

SDMA

Display/TV Ctl

Pre & Post Processing

CSPI (3)

PWM

Internal

Memory

Expansion

SDHC (2)

PCMCIA/CF

Mem Stick (2)

SIM

Timers

RTC

USB Host (2)

WDOG

GPT

USB-OTG

KPP

8 x 8

Keypad

ARM11^TMPlatform

ARM1136JF-S^TM

EPIT (2)

GPIO

CCM

ATA

I-Cache

Serial

EPROM

1-WIRE

®

Security

SCC

RTIC

D-Cache

IIM

Debug

ECT

L2-Cache

GPU

*

MAX

ROMPATCH

VFP

RNGA

SJC

GPS

ETM

* GPU unavailable for i.MX31L

ATA

Hard Drive

Fast

IrDA

USB

Host/Device

PC

Card

PC

Card

SD

Card

Bluetooth

Baseband

WLAN

Figure 1. MCIMX31C Simplified Interface Block Diagram

2 Functional Description and Application Information

2.1

ARM11 Microprocessor Core

The CPU of the MCIMX31C is the ARM1136JF-S core based on the ARM v6 architecture. It supports the

®

ARM Thumb instruction sets, features Jazelle technology (which enables direct execution of Java byte

codes), and a range of SIMD DSP instructions that operate on 16-bit or 8-bit data values in 32-bit registers.

The ARM1136JF-S processor core features:

™

•

Integer unit with integral EmbeddedICE logic

Eight-stage pipeline

Branch prediction with return stack

Low-interrupt latency

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

4

Freescale Semiconductor

Functional Description and Application Information

•

Instruction and data memory management units (MMUs), managed using micro TLB structures

backed by a unified main TLB

•

Instruction and data L1 caches, including a non-blocking data cache with Hit-Under-Miss

Virtually indexed/physically addressed L1 caches

64-bit interface to both L1 caches

Write buffer (bypassable)

™

High-speed Advanced Micro Bus Architecture (AMBA) L2 interface

Vector Floating Point co-processor (VFP) for 3D graphics and other floating-point applications

hardware acceleration

™

•

ETM and JTAG-based debug support

2.1.1

Memory System

The ARM1136JF-S complex includes 16 KB Instruction and 16 KB Data L1 caches. It connects to the

MCIMX31C L2 unified cache through 64-bit instruction (read-only), 64-bit data read/write

(bi-directional), and 64-bit data write interfaces.

The embedded 16K SRAM can be used for audio streaming data to avoid external memory accesses for

the low-power audio playback, for security, or for other applications. There is also a 32-KB ROM for

bootstrap code and other frequently-used code and data.

A ROM patch module provides the ability to patch the internal ROM. It can also initiate an external boot

by overriding the boot reset sequence by a jump to a configurable address.

Table 2 shows information about the MCIMX31C core in tabular form.

Table 2. MCIMX31C Core

Core

Acronym

Core

Name

Integrated Memory

Includes

Brief Description

ARM11 or ARM1136 The ARM1136™ Platform consists of the ARM1136JF-S core, the ETM

• 16 Kbyte

ARM1136 Platform

real-time debug modules, a 6 x 5 multi-layer AHB crossbar switch (MAX), and a

Vector Floating Processor (VFP).

Instruction Cache

• 16 Kbyte Data

Cache

• 128 Kbyte L2

Cache

The MCIMX31C provides a high-performance ARM11 microprocessor core and

highly integrated system functions. The ARM Application Processor (AP) and

other subsystems address the needs of the personal, wireless, and portable

product market with integrated peripherals, advanced processor core, and

power management capabilities.

• 32 Kbyte ROM

• 16 Kbyte RAM

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

5

Functional Description and Application Information

2.2

Module Inventory

Table 3 shows an alphabetical listing of the modules in the multimedia applications processor. For

extended descriptions of the modules, see the reference manual. A cross-reference is provided to the

electrical specifications and timing information for each module with external signal connections.

Table 3. Digital and Analog Modules

Block

Mnemonic

Functional

Grouping

Section/

Page

Block Name

Brief Description

1-Wire® 1-Wire Interface Connectivity The 1-Wire module provides bi-directional communication between

Peripheral the ARM11 core and external 1-Wire devices.

4.3.4/20

ATA

Advanced

Connectivity The ATA block is an AT attachment host interface. It is designed to

4.3.5/21

Technology (AT) Peripheral

Attachment

interface with IDE hard disc drives and ATAPI optical disc drives.

AUDMUX Digital Audio

Multiplexer

Multimedia

Peripheral

The AUDMUX interconnections allow multiple, simultaneous

audio/voice/data flows between the ports in point-to-point or

point-to-multipoint configurations.

4.3.6/30

CAMP

CCM

Clock Amplifier Clock

Module

The CAMP converts a square wave/sinusoidal input into a rail-to-rail

square wave. The output of CAMP feeds the predivider.

4.3.3/19

—

Clock Control

Module

Clock

The CCM provides clock, reset, and power management control for

the MCIMX31C.

CSPI

Configurable

Connectivity The CSPI is equipped with data FIFOs and is a master/slave

4.3.7/30

SerialPeripheral Peripheral

Interface (x 3)

configurable serial peripheral interface module, capable of

interfacing to both SPI master and slave devices.

DPLL

ECT

EMI

Digital Phase

Lock Loop

Clock

The DPLLs produce high-frequency on-chip clocks with low

frequency and phase jitters.

Note: External clock sources provide the reference frequencies.

4.3.8/31

—

Embedded

Cross Trigger

Debug

The ECT is composed of three CTIs (Cross Trigger Interface) and

one CTM (Cross Trigger Matrix—key in the multi-core and

multi-peripheral debug strategy.

External

Memory

Interface

Memory

Interface

(EMI)

The EMI includes

• Multi-Master Memory Interface (M3IF)

• Enhanced SDRAM Controller (ESDCTL)

• NAND Flash Controller (NFC)

—

4.3.9.3/40,

4.3.9.1/32,

4.3.9.2/35

• Wireless External Interface Module (WEIM)

EPIT

Enhanced

Periodic

Interrupt Timer

Timer

Peripheral

The EPIT is a 32-bit “set and forget” timer which starts counting after

the EPIT is enabled by software. It is capable of providing precise

interrupts at regular intervals with minimal processor intervention.

—

ETM

FIR

Embedded

Trace Macrocell

Debug/Trace The ETM (from ARM, Ltd.) supports real-time instruction and data

tracing by way of ETM auxiliary I/O port.

4.3.10/48

Fast InfraRed

Interface

Connectivity This FIR is capable of establishing a 0.576 Mbit/s, 1.152 Mbit/s or 4 4.3.11/49

Peripheral

Mbit/s half duplex link via a LED and IR detector. It supports 0.576

Mbit/s, 1.152 Mbit/s medium infrared (MIR) physical layer protocol

and 4Mbit/s fast infrared (FIR) physical layer protocol defined by

IrDA, version 1.4.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

6

Freescale Semiconductor

Functional Description and Application Information

Table 3. Digital and Analog Modules (continued)

Block

Mnemonic

Functional

Grouping

Section/

Page

Block Name

Brief Description

Fusebox Fusebox

ROM

The Fusebox is a ROM that is factory configured by Freescale.

4.3.12/49

See also

Table 10

GPIO

General

Purpose I/O

Module

Pins

The GPIO provides several groups of 32-bit bidirectional, general

purpose I/O. This peripheral provides dedicated general-purpose

signals that can be configured as either inputs or outputs.

—

GPT

GPU

General

Purpose Timer Peripheral

Timer

The GPT is a multipurpose module used to measure intervals or

generate periodic output.

—

Graphics Multimedia

The GPU provides hardware acceleration for 2D and 3D graphics

algorithms.

Processing Unit Peripheral

Inter IC

2

I C

Connectivity The I C provides serial interface for controlling the Sensor Interface 4.3.13/50

Communication Peripheral

and other external devices. Data rates of up to 100 Kbits/s are

supported.

IIM

IPU

KPP

IC Identification ID

Module

The IIM provides an interface for reading device identification.

—

Image

Multimedia

The IPU processes video and graphics functions in the MCIMX31C 4.3.14/51,

and interfaces to video, still image sensors, and displays.

Processing Unit Peripheral

4.3.15/53

Keypad Port Connectivity The KPP is used for keypad matrix scanning or as a general purpose

—

Peripheral

I/O. This peripheral simplifies the software task of scanning a keypad

matrix.

MPEG-4 MPEG-4 Video Multimedia

The MPEG-4 encoder accelerates video compression, following the

—

Encoder

Peripherals MPEG-4 standard

MSHC

PADIO

Memory Stick

Host Controller Peripheral

Connectivity The MSHC is placed in between the AIPS and the customer memory 4.3.16/78

stick to support data transfer from the MCIMX31C to the customer

memory stick.

Pads I/O

Buffers and The PADIO serves as the interface between the internal modules and

Drivers the device's external connections.

4.3.1/16

4.3.17/80

4.3.18/82

—

PCMCIA PCM

Connectivity The PCMCIA Host Adapter provides the control logic for PCMCIA

Peripheral

socket interfaces.

PWM

Pulse-Width

Modulator

Timer

Peripheral

The PWM has a 16-bit counter and is optimized to generate sound

from stored sample audio images. It can also generate tones.

RNGA

Random

Number

Generator

Accelerator

Security

The RNGA module is a digital integrated circuit capable of generating

32-bit random numbers. It is designed to comply with FIPS-140

standards for randomness and non-determinism.

RTC

Real Time Clock Timer

Peripheral

The RTC module provides a current stamp of seconds, minutes,

hours, and days. Alarm and timer functions are also available for

programming. The RTC supports dates from the year 1980 to 2050.

—

RTIC

Run-Time

Integrity

Security

The RTIC ensures the integrity of the peripheral memory contents

and assists with boot authentication.

Checkers

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

7

Functional Description and Application Information

Table 3. Digital and Analog Modules (continued)

Block

Mnemonic

Functional

Grouping

Section/

Page

Block Name

Brief Description

SCC

SDHC

SDMA

SIM

Security

Controller

Module

Security

The SCC is a hardware component composed of two blocks—the

Secure RAM module, and the Security Monitor. The Secure RAM

provides a way of securely storing sensitive information.

—

Secured Digital Connectivity The SDHC controls the MMC (MultiMediaCard), SD (Secure Digital) 4.3.19/83

Host Controller Peripheral

memory, and I/O cards by sending commands to cards and

performing data accesses to and from the cards.

Smart Direct

Memory Access Control

Peripheral

System

The SDMA controller maximizes the system’s performance by

relieving the ARM core of the task of bulk data transfer from memory

to memory or between memory and on-chip peripherals.

—

Subscriber

Identification

Module

Connectivity The SIM interfaces to an external Subscriber Identification Card. It is 4.3.20/84

Peripheral

an asynchronous serial interface adapted for Smart Card

communication for e-commerce applications.

SJC

Secure JTAG

Controller

Debug

The SJC provides debug and test control with maximum security and 4.3.21/88

provides a flexible architecture for future derivatives or future

multi-cores architecture.

SSI

Synchronous

Serial Interface Peripheral

Multimedia

The SSI is a full-duplex, serial port that allows the device to

communicate with a variety of serial devices, such as standard

codecs, Digital Signal Processors (DSPs), microprocessors,

peripherals, and popular industry audio codecs that implement the

inter-IC sound bus standard (I2S) and Intel AC97 standard.

4.3.22/90

UART

USB

Universal

Connectivity The UART provides serial communication capability with external

—

Asynchronous

Receiver/Trans

mitter

Peripheral

devices through an RS-232 cable or through use of external circuitry

that converts infrared signals to electrical signals (for reception) or

transforms electrical signals to signals that drive an infrared LED (for

transmission) to provide low speed IrDA compatibility.

Universal Serial Connectivity • USB Host 1 is designed to support transceiverless connection to 4.3.23/98

Bus—

2 Host

Controllers and

1 OTG

(On-The-Go)

Peripherals

the on-board peripherals in Low Speed and Full Speed mode, and

connection to the ULPI (UTMI+ Low-Pin Count) and Legacy Full

Speed transceivers.

• USB Host 2 is designed to support transceiverless connection to

the Cellular Modem Baseband Processor.

• The USB-OTG controller offers HS/FS/LS capabilities in Host

mode and HS/FS in device mode. In Host mode, the controller

supports direct connection of a FS/LS device (without external

hub). In device (bypass) mode, the OTG port functions as gateway

between the Host 1 Port and the OTG transceiver.

WDOG

Watchdog Timer Timer

Module Peripheral

The WDOG module protects against system failures by providing a

method for the system to recover from unexpected events or

programming errors.

—

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

8

Freescale Semiconductor

Signal Descriptions

3 Signal Descriptions

Signal descriptions are in the reference manual. Special signal considerations are listed following this

paragraph. The BGA ball assignment is in Section 5, “Package Information and Pinout,” on page 99.

Special Signal Considerations:

•

Tamper detect (GPIO1_6)

Tamper detect logic is used to issue a security violation. This logic is activated if the tamper detect

input is asserted.

The tamper detect logic is disabled after reset. After enabling the logic, it is impossible to disable

it until the next reset. The GPR[16] bit functions as the tamper detect enable bit.

GPIO1_6 functions similarly to other I/O with GPIO capabilities regardless of the status of the

tamper detect enable bit. (For example, the GPIO1_6 can function as an input with GPIO

capabilities, such as sampling through PSR or generating interrupts.)

•

Power ready (GPIO1_5)

The power ready input, GPIO1_5, should be connected to an external power management IC power

ready output signal. If not used, GPIO1_5 must either be (a) externally pulled-up to NVCC1 or (b)

a no connect, internally pulled-up by enabling the on-chip pull-up resistor. GPIO1_5 is a dedicated

input and cannot be used as a general-purpose input/output.

SJC_MOD

SJC_MOD must be externally connected to GND for normal operation. Termination to GND

through an external pull-down resistor (such as 1 kΩ) is allowed, but the value should be much

smaller than the on-chip 100 kΩ pull-up.

•

CE_CONTROL

CE_CONTROL is a reserved input and must be externally tied to GND through a 1 kΩ resistor.

M_REQUEST and M_GRANT

These two signals are not utilized internally. The user should make no connection to these signals.

Clock Source Select (CLKSS)

The CLKSS is the input that selects the default reference clock source providing input to the DPLL.

To select CKIH, tie CLKSS to NVCC1. To select CKIL, tie CLKSS to ground. After initialization,

the reference clock source can be changed (initial setting is overwritten) by programming the

PRCS bits in the CCMR.

4 Electrical Characteristics

This section provides the device-level and module-level electrical characteristics for the MCIMX31C.

4.1

Chip-Level Conditions

This section provides the device-level electrical characteristics for the IC. See Table 4 for a quick reference

to the individual tables and sections.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

9

Electrical Characteristics

Table 4. MCIMX31C Chip-Level Conditions

For these characteristics, …

Topic appears …

Table 5, “Absolute Maximum Ratings”

on page 10

on page 12

on page 13

on page 14

on page 15

Table 6, “Thermal Resistance Data—19 × 19 mm Package”

Table 7, “Operating Ranges”

Table 8, “Specific Operating Ranges for Silicon Revision 2.0 and 2.0.1”

Table 9, “Interface Frequency”

Section 4.1.1, “Supply Current Specifications”

Section 4.2, “Supply Power-Up/Power-Down Requirements and Restrictions”

CAUTION

Stresses beyond those listed under Table 5, "Absolute Maximum Ratings,"

on page 10 may cause permanent damage to the device. These are stress

ratings only. Functional operation of the device at these or any other

conditions beyond those indicated under Table 7, "Operating Ranges," on

page 12 is not implied. Exposure to absolute-maximum-rated conditions for

extended periods may affect device reliability.

Table 5. Absolute Maximum Ratings

Parameter

Symbol

Min

Max

Units

Supply Voltage (Core)

Supply Voltage (I/O)

Input Voltage Range

Storage Temperature

ESD Damage Immunity:

QVCC

NVCC

–0.5

–40

1.47

3.1

V

max

V

NVCC +0.3

125

Imax

o

T

C

storage

1

Human Body Model (HBM)

—

H1C

V

esd

Machine Model (MM)

200

2

Charge Device Model (CDM)

C2

3

Offset voltage allowed in run mode between core supplies.

V

15

mV

core_offset

1

2

HBM ESD classification level according to the AEC-Q100-002-Rev-D standard.

Integrated circuit CDM ESD classification level according to the AEC-Q100-011-Rev-B standard.

3

The offset is the difference between all core voltage pair combinations of QVCC, QVCC1, and QVCC4.

Table 6 provides the thermal resistance data for the 19 × 19 mm, 0.8 mm pitch package.

Table 6. Thermal Resistance Data—19 × 19 mm Package

Rating

Board

Symbol

Value

Unit

Notes

Junction to Ambient (natural convection)

Junction to Ambient (@200 ft/min)

Single layer board (1s)

Four layer board (2s2p)

Single layer board (1s)

R

46

29

38

°C/W

1, 2, 3

θJA

R

θJMA

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

10

Freescale Semiconductor

Electrical Characteristics

Table 6. Thermal Resistance Data—19 × 19 mm Package (continued)

Rating

Board

Symbol

Value

Unit

Notes

Junction to Ambient (@200 ft/min)

Junction to Board

Four layer board (2s2p)

R

25

19

10

2

°C/W

1, 2, 3

1, 3

θJMA

—

R

θJB

Junction to Case (Top)

R

1, 4

θJCtop

Junction to Package Top (natural convection)

Ψ

1, 5

JT

NOTES

1. Junction temperature is a function of die size, on-chip power dissipation, package thermal

resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of

other components on the board, and board thermal resistance.

2. Junction-to-Ambient Thermal Resistance determined per JEDEC JESD51-3 and JESD51-6.

Thermal test board meets JEDEC specification for this package.

3. Junction-to-Board thermal resistance determined per JEDEC JESD51-8. Thermal test board

meets JEDEC specification for the specified package.

4. Junction-to-Case at the top of the package determined using MIL-STD 883 Method 1012.1. The

cold plate temperature is used for the case temperature. Reported value includes the thermal

resistance of the interface layer.

5. Thermal characterization parameter indicating the temperature difference between the package

top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the

thermal characterization parameter is written as Psi-JT.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

11

Electrical Characteristics

Table 7 provides the operating ranges.

NOTE

The term NVCC in this section refers to the associated supply rail of an

input or output. The association is shown in the Signal Multiplexing chapter

of the reference manual.

CAUTION

NVCC6 and NVCC9 must be at the same voltage potential. These supplies

are connected together on-chip to optimize ESD damage immunity.

Table 7. Operating Ranges

Symbol

Parameter

Min

Max

Units

1 2

3

QVCC,

QVCC1,

QVCC4

Core Operating Voltage ,

0 ≤ f

≤ 400 MHz

1.22

0.95

1.75

1.47

—

V

ARM

State Retention Voltage

4

NVCC1,

NVCC3–10

I/O Supply Voltage, except DDR

3.1

V

NVCC2,

NVCC21,

NVCC22

I/O Supply Voltage, DDR only

1.75

1.3

1.95

1.47

5

FVCC, MVCC, PLL (Phase-Locked Loop) and FPM (Frequency Pre-multiplier) Supply Voltage

SVCC, UVCC

V

IOQVDD

On-device Level Shifter Supply Voltage

1.6

—

1.9

—

V

6

Fusebox read Supply Voltage

FUSE_VDD

7

Fusebox write (program) Supply Voltage

Operating Ambient Temperature Range

Operating Junction Temperature Range

3.0

–40

—

3.3

85

o

T

C

A

o

T

105

C

j

1

2

Measured at package balls, including peripherals, ARM, and L2 cache supplies (QVCC, QVCC1, QVCC4, respectively).

The core voltage must be higher than 1.38V to avoid corrupted data during transfers from the USB HS. Please refer to Errata

file ENGcm02610 ID

3

4

The SR voltage is applied to QVCC, QVCC1, and QVCC4 after the device is placed in SR mode. The Real-Time Clock (RTC)

is operational in State Retention (SR) mode.

Overshoot and undershoot conditions (transitions above NVCC and below GND) on I/O must be held below 0.6 V, and the

duration of the overshoot/undershoot must not exceed 10% of the system clock cycle. Overshoot/undershoot must be

controlled through printed circuit board layout, transmission line impedance matching, signal line termination, or other

methods. Non-compliance to this specification may affect device reliability or cause permanent damage to the device.

5

PLL voltage must not be altered after power-up, otherwise the PLL will be unstable and lose lock. To minimize inducing noise

on the PLL supply line, source the voltage from a low-noise, dedicated supply. PLL parameters in Table 28, "DPLL

Specifications," on page 31, are guaranteed over the entire specified voltage range.

6

7

In read mode, FUSE_VDD can be floated or grounded.

Fuses might be inadvertently blown if written to while the voltage is below this minimum.

Table 8. Specific Operating Ranges for Silicon Revision 2.0 and 2.0.1

Symbol

Parameter

Min

Max

Units

1

Fusebox read Supply Voltage

Fusebox write (program) Supply Voltage

—

V

FUSE_VDD

2

3.0

3.3

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

12

Freescale Semiconductor

Electrical Characteristics

1

2

In read mode, FUSE_VDD should be floated or grounded.

Fuses might be inadvertently blown if written to while the voltage is below the minimum.

Table 9 provides information for interface frequency limits. For more details about clocks characteristics,

see Section 4.3.8, “DPLL Electrical Specifications” on page 31 and Section 4.3.3, “Clock Amplifier

Module (CAMP) Electrical Characteristics” on page 19.

Table 9. Interface Frequency

ID

Parameter

JTAG TCK Frequency

Symbol

Min

Typ

Max

Units

1

2

3

f

DC

32

15

5

32.768

26

10

38.4

75

MHz

kHz

JTAG

1

CKIL Frequency

f

CKIL

2

CKIH Frequency

f

MHz

CKIH

1

2

CKIL must be driven by an external clock source to ensure proper start-up and operation of the device. CKIL is needed to clock

the internal reset synchronizer, the watchdog, and the real-time clock.

DPTC functionality, specifically the voltage/frequency relation table, is dependent on CKIH frequency. At the time of publication,

standard tables used by Freescale OSs provided for a CKIH frequency of 26 MHz only. Any deviation from this frequency

requires an update to the OS. For more details, refer to the particular OS user's guide documentation. DPTC/DVFS are not

supported for fARM ≤ 400MHz.

Table 10 shows the fusebox supply current parameters.

Table 10. Fusebox Supply Current Parameters

Description Symbol Minimum Typical Maximum Units

35 60 mA

Ref. Num

1

eFuse Program Current.

Current to program one eFuse bit: efuse_pgm = 3.0V

I

—

program

1

The current I is during program time (t ).

program

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

13

Electrical Characteristics

4.1.1

Supply Current Specifications

Table 11 shows the core current consumption for –40°C to 85°C for Silicon Revision 2.0 and 2.0.1 for the

MCIMX31C.

1, 2

Table 11. Current Consumption for –40°C to 85°C

for Silicon Revision 2.0 and 2.0.1

FVCC + MVCC

QVCC

(Peripheral)

QVCC1

(ARM)

QVCC4

(L2)

+ SVCC + UVCC

Mode

Conditions

Unit

(PLL)

Typ Max Typ

0.20 9.00

Max

Typ Max

Typ

Max

Deep

Sleep

• QVCC = 0.95 V

—

0.04

0.14

mA

• ARM and L2 caches are power gated

(QVCC1 = QVCC4 = 0 V)

• All PLLs are off, VCC = 1.4 V

• ARM is in well bias

• FPM is off

• 32 kHz input is on

• CKIH input is off

• CAMP is off

• TCK input is off

• All modules are off

• No external resistive loads

• RNGA oscillator is off

State

• QVCC and QVCC1 = 0.95 V

0.20 9.00 0.15 3.50

—

0.04

0.14

mA

Retention • L2 caches are power gated (QVCC4 = 0 V)

• All PLLs are off, VCC = 1.4 V

• ARM is in well bias

• FPM is off

• 32 kHz input is on

• CKIH input is off

• CAMP is off

• TCK input is off

• All modules are off

• No external resistive loads

• RNGA oscillator is off

Wait

• QVCC,QVCC1, and QVCC4 = 1.22 V

• ARM is in wait for interrupt mode

• MAX is active

7.00 19.00 3.00

100.00

0.03 0.90

4.00

6.00

mA

• L2 cache is stopped but powered

• MCU PLL is on (400 MHz), VCC = 1.4 V

• USB PLL and SPLL are off, VCC = 1.4 V

• FPM is on

• CKIH input is on

• CAMP is on

• 32 kHz input is on

• All clocks are gated off

• All modules are off

(by programming CGR[2:0] registers)

• RNGA oscillator is off

• No external resistive loads

1

2

Typical column: TA = 25°C

Maximum column: TA = 85°C

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

14

Freescale Semiconductor

Electrical Characteristics

4.2

Supply Power-Up/Power-Down Requirements and Restrictions

Any MCIMX31C board design must comply with the power-up and power-down sequence guidelines as

described in this section to guarantee reliable operation of the device. Any deviation from these sequences

may result in any or all of the following situations:

•

Cause excessive current during power-up phase

Prevent the device from booting

Cause irreversible damage to the MCIMX31C (worst-case scenario)

4.2.1

Powering Up

The Power On Reset (POR) pin must be kept asserted (low) throughout the power-up sequence. Power-up

logic must guarantee that all power sources reach their target values prior to the release (de-assertion) of

POR. Figure 2 and Figure 3 show two options of the power-up sequence.

NOTE

Stages need to be performed in the order shown; however, within each stage,

supplies can be powered up in any order. For example, supplies IOQVDD, NVCC1,

and NVCC3 through NVCC10 do not need to be powered up in the order shown.

CAUTION

NVCC6 and NVCC9 must be at the same voltage potential. These supplies

are connected together on-chip to optimize ESD damage immunity.

Notes:

1

The board design must guarantee that supplies reach 90% level before

Hold POR Asserted

transition to the next state, using Power Management IC or other

means.

2

3

4

5

The NVCC1 supply must not precede IOQVDD by more than 0.2 V until

IOQVDD has reached 1.5 V. If IOQVDD is powered up first, there are

no restrictions.

The parallel paths in the flow indicate that supply group NVCC2,

NVCC21, and NVCC22, and supply group FVCC, MVCC, SVCC, and

UVCC ramp-ups are independent.

FUSE_VDD should not be driven on power-up for Silicon Revision 2.0

and 2.0.1. This supply is dedicated for fuse burning (programming),

and should not be driven upon boot-up.

Raising IOQVDD before NVCC21 produces a slight increase in current

drain on IOQVDD of approximately 3–5 mA. The current increase will

not damage the IC. Refer to Errata ID TLSbo91750 for details.

QVCC, QVCC1, QVCC4¹

1, 2

IOQVDD, NVCC1, NVCC3–10

1,3

NVCC2, NVCC21, NVCC22^{1, 3}

FVCC, MVCC, SVCC, UVCC

4

Release POR

Figure 2. Option 1 Power-Up Sequence for Silicon Revision 2.0 and 2.0.1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

15

Electrical Characteristics

Notes:

1

The board design must guarantee that supplies reach

Hold POR Asserted

90% level before transition to the next state, using Power

Management IC or other means.

2

3

The NVCC1 supply must not precede IOQVDD by more

than 0.2 V until IOQVDD has reached 1.5 V. If IOQVDD

is powered up first, there are no restrictions.

Raising NVCC2, NVCC21, and NVCC22 at the same

time as IOQVDD does not produce the slight increase in

current drain on IOQVDD (as described in Figure 2,

Note 5).

FUSE_VDD should not be driven on power-up for Silicon

Revision2.0 and 2.0.1. This supply is dedicated for fuse

burning (programming), and should not be driven upon

boot-up.

QVCC, QVCC1, QVCC4¹

1, 2,3

4

IOQVDD, NVCC1, NVCC3–10, NVCC2, NVCC21, NVCC22

1

FVCC, MVCC, SVCC, UVCC

4

Release POR

Figure 3. Option 2 Power-Up Sequence (Silicon Revision 2.0 and 2.0.1)

4.2.2

Powering Down

The power-down sequence should be completed as follows:

1. Lower the FUSE_VDD supply (when in write mode).

2. Lower the remaining supplies.

4.3

Module-Level Electrical Specifications

This section contains the MCIMX31C electrical information including timing specifications, arranged in

alphabetical order by module name.

4.3.1

I/O Pad (PADIO) Electrical Specifications

This section specifies the AC/DC characterization of functional I/O of the MCIMX31C. There are two

main types of I/O: regular and DDR. In this document, the “Regular” type is referred to as GPIO.

4.3.1.1

DC Electrical Characteristics

The MCIMX31C I/O parameters appear in Table 12 for GPIO. See Table 7, "Operating Ranges," on page

12 for temperature and supply voltage ranges.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

16

Freescale Semiconductor

Electrical Characteristics

NOTE

The term NVCC in this section refers to the associated supply rail of an

input or output. The association is shown in the Signal Multiplexing chapter

of the reference manual. NVCC for Table 12 refers to NVCC1 and

NVCC3–10; QVCC refers to QVCC, QVCC1, and QVCC4.

Table 12. GPIO DC Electrical Parameters

Parameter

Symbol

Test Conditions

= –1 mA

Min

Typ

Max

Units

High-level output voltage

V

I

NVCC –0.15

—

V

OH

I

= specified Drive

0.8*NVCC

OH

Low-level output voltage

V

I

= 1 mA

—

0.15

V

OL

I

= specified Drive

0.2*NVCC

—

V

OL

High-level output current, slow slew rate

I

V

=0.8*NVCC

mA

OH_S

OH

Std Drive

High Drive

Max Drive

–2

–4

–8

High-level output current, fast slew rate

Low-level output current, slow slew rate

Low-level output current, fast slew rate

I

V

=0.8*NVCC

—

mA

OH_F

OH

Std Drive

High Drive

Max Drive

–4

–6

–8

I

=0.2*NVCC

OL

OL_S

OL_F

Std Drive

High Drive

Max Drive

2

4

8

I

=0.2*NVCC

OL

Std Drive

High Drive

Max Drive

4

6

8

High-Level DC input voltage

Low-Level DC input voltage

Input Hysteresis

V

—

0.7*NVCC

—

NVCC

V

IH

V

0

0.3*QVCC

IL

V

Hysteresis enabled

0.25

—

HYS

Schmitt trigger VT+

V +

Hysteresis enabled

0.5*QVCC

—

T

Schmitt trigger VT–

V –

Hysteresis enabled

—

0.5*QVCC

T

1

Pull-up resistor (100 kΩ PU)

Pull-down resistor (100 kΩ PD)

Input current (no PU/PD)

Input current (100 kΩ PU)

R

—

100

—

1

PU

PD

kΩ

μA

1

I

V = NVCC or GND

IN

I

V = 0

—

25

μA

I

Input current (100 kΩ PD)

I

V = NVCC

—

28

2

μA

IN

I

Tri-state leakage current

I

V = NVCC or GND

OZ

I

I/O = High Z

1

Not a precise value. Measurements made on small sample size have shown variations of 50% or more.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

17

Electrical Characteristics

The MCIMX31C I/O parameters appear in Table 13 for DDR (Double Data Rate). See Table 7, "Operating

Ranges," on page 12 for temperature and supply voltage ranges.

NOTE

NVCC for Table 13 refers to NVCC2, NVCC21, and NVCC22.

Table 13. DDR (Double Data Rate) I/O DC Electrical Parameters

Parameter

High-level output voltage

Symbol

Test Conditions

= –1 mA

Min

Typ

Max

Units

V

I

NVCC –0.12

—

V

OH

I

= specified Drive 0.8*NVCC

OH

Low-level output voltage

High-level output current

V

I

= 1 mA

OL

—

0.08

V

OL

= specified Drive

0.2*NVCC

—

V

OL

I

V

=0.8*NVCC

mA

OH

Std Drive

High Drive

Max Drive

DDR Drive

=0.2*NVCC

OL

–3.6

–7.2

–10.8

–14.4

1

Low-level output current

I

V

—

mA

OL

Std Drive

High Drive

Max Drive

3.6

7.2

10.8

14.4

1

DDR Drive

High-Level DC input voltage

Low-Level DC input voltage

Tri-state leakage current

V

—

0.7*NVCC NVCC NVCC+0.3

V

IH

V

I

–0.3

—

0

0.3*NVCC

2

IL

V = NVCC or GND

—

μA

OZ

I

I/O = High Z

1

Use of DDR Drive can result in excessive overshoot and ringing.

4.3.2

AC Electrical Characteristics

Figure 4 depicts the load circuit for outputs. Figure 5 depicts the output transition time waveform. The

range of operating conditions appears in Table 14 for slow general I/O, Table 15 for fast general I/O, and

Table 16 for DDR I/O (unless otherwise noted).

From Output

Under Test

Test Point

CL

CL includes package, probe and fixture capacitance

Figure 4. Load Circuit for Output

NVCC

0V

80%

20%

80%

20%

Output (at I/O)

PA1

Figure 5. Output Transition Time Waveform

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

18

Freescale Semiconductor

Electrical Characteristics

1

Table 14. AC Electrical Characteristics of Slow General I/O

Test

Condition

ID

Parameter

Symbol

Min

Typ

Max

Units

PA1 Output Transition Times (Max Drive)

Output Transition Times (High Drive)

Output Transition Times (Std Drive)

tpr

25 pF

50 pF

0.92

1.5

1.95

2.98

3.17

4.75

ns

tpr

25 pF

50 pF

1.52

2.75

—

4.81

8.42

ns

25 pF

50 pF

2.79

5.39

—

8.56

16.43

1

Fast/slow characteristic is selected per GPIO (where available) by “slew rate” control. See reference manual.

1

2

Table 15. AC Electrical Characteristics of Fast General I/O

Test

Condition

ID

Parameter

Symbol

Min

Typ

Max

Units

PA1

Output Transition Times (Max Drive)

tpr

25 pF

50 pF

0.68

1.34

1.33

2.6

2.07

4.06

ns

Output Transition Times (High Drive)

Output Transition Times (Std Drive)

tpr

25 pF

50 pF

.91

1.79

1.77

3.47

2.74

5.41

ns

25 pF

50 pF

1.36

2.68

2.64

5.19

4.12

8.11

1

2

Fast/slow characteristic is selected per GPIO (where available) by “slew rate” control. See reference manual.

Use of GPIO in fast mode with the associated NVCC > 1.95 V can result in excessive overshoot and ringing.

Table 16. AC Electrical Characteristics of DDR I/O

Test

ID

Parameter

Symbol

Min

Typ

Max

Units

Condition

1

PA1

Output Transition Times (DDR Drive)

tpr

25 pF

50 pF

0.51

0.97

0.82

1.58

1.28

2.46

ns

Output Transition Times (Max Drive)

Output Transition Times (High Drive)

Output Transition Times (Std Drive)

tpr

25 pF

50 pF

0.67

1.29

1.08

2.1

1.69

3.27

ns

25 pF

50 pF

.99

1.93

1.61

3.13

2.51

4.89

25 pF

50 pF

1.96

3.82

3.19

6.24

4.99

9.73

1

Use of DDR Drive can result in excessive overshoot and ringing.

4.3.3

Clock Amplifier Module (CAMP) Electrical Characteristics

This section outlines the Clock Amplifier Module (CAMP) specific electrical characteristics. Table 17

shows clock amplifier electrical characteristics.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

19

Electrical Characteristics

Table 17. Clock Amplifier Electrical Characteristics for CKIH Input

Parameter

Input Frequency

Min

Typ

Max

Units

15

0

—

50

75

0.3

3

MHz

V

VIL (for square wave input)

VIH (for square wave input)

Sinusoidal Input Amplitude

Duty Cycle

1

(VDD – 0.25)

V

2

0.4

VDD

55

Vp-p

%

45

1

2

VDD is the supply voltage of CAMP. See reference manual.

This value of the sinusoidal input will be measured through characterization.

4.3.4

1-Wire Electrical Specifications

Figure 6 depicts the RPP timing, and Table 18 lists the RPP timing parameters.

OWIRE Tx

DS2502 Tx

“Presence Pulse”

“Reset Pulse”

OW2

1-Wire bus

(BATT_LINE)

OW3

OW1

OW4

Figure 6. Reset and Presence Pulses (RPP) Timing Diagram

Table 18. RPP Sequence Delay Comparisons Timing Parameters

ID

Parameters

Symbol

Min

Typ

Max

Units

OW1

OW2

OW3

OW4

Reset Time Low

Presence Detect High

Presence Detect Low

Reset Time High

t

480

15

511

—

60

µs

RSTL

t

PDH

t

60

—

240

—

PDL

t

480

512

RSTH

Figure 7 depicts Write 0 Sequence timing, and Table 19 lists the timing parameters.

OW6

1-Wire bus

(BATT_LINE)

OW5

Figure 7. Write 0 Sequence Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

20

Freescale Semiconductor

Electrical Characteristics

Table 19. WR0 Sequence Timing Parameters

ID

Parameter

Symbol

Min

Typ

Max

Units

OW5

OW6

Write 0 Low Time

Transmission Time Slot

t

60

100

117

120

µs

WR0_low

t

OW5

SLOT

Figure 8 depicts Write 1 Sequence timing, Figure 9 depicts the Read Sequence timing, and Table 20 lists

the timing parameters.

OW8

1-Wire bus

(BATT_LINE)

OW7

Figure 8. Write 1 Sequence Timing Diagram

OW8

1-Wire bus

(BATT_LINE)

OW7

OW9

Figure 9. Read Sequence Timing Diagram

Table 20. WR1/RD Timing Parameters

ID

Parameter

Symbol

Min

Typ

Max

Units

OW7

OW8

OW9

Write 1 / Read Low Time

Transmission Time Slot

Release Time

t

1

5

15

120

45

µs

LOW1

t

60

15

117

—

SLOT

t

RELEASE

4.3.5

ATA Electrical Specifications (ATA Bus, Bus Buffers)

This section discusses ATA parameters. For a detailed description, refer to the ATA specification.

The user needs to use level shifters for 3.3 Volt or 5.0 Volt compatibility on the ATA interface.

The use of bus buffers introduces delay on the bus and introduces skew between signal lines. These factors

make it difficult to operate the bus at the highest speed (UDMA-5) when bus buffers are used. If fast

UDMA mode operation is needed, this may not be compatible with bus buffers.

Another area of attention is the slew rate limit imposed by the ATA specification on the ATA bus.

According to this limit, any signal driven on the bus should have a slew rate between 0.4 and 1.2 V/ns with

a 40 pF load. Not many vendors of bus buffers specify slew rate of the outgoing signals.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

21

Electrical Characteristics

When bus buffers are used, the ata_data bus buffer is special. This is a bidirectional bus buffer, so a

direction control signal is needed. This direction control signal is ata_buffer_en. When its high, the bus

should drive from host to device. When its low, the bus should drive from device to host. Steering of the

signal is such that contention on the host and device tri-state busses is always avoided.

4.3.5.1

Timing Parameters

In the timing equations, some timing parameters are used. These parameters depend on the implementation

of the ATA interface on silicon, the bus buffer used, the cable delay and cable skew. Table 21 shows ATA

timing parameters.

Table 21. ATA Timing Parameters

Value/

Contributing Factor

Name

Description

1

T

Bus clock period (ipg_clk_ata)

peripheral clock

frequency

ti_ds

Set-up time ata_data to ata_iordy edge (UDMA-in only)

UDMA0

UDMA1

UDMA2, UDMA3

UDMA4

15 ns

10 ns

7 ns

5 ns

UDMA5

4 ns

ti_dh

tco

Hold time ata_iordy edge to ata_data (UDMA-in only)

UDMA0, UDMA1, UDMA2, UDMA3, UDMA4

UDMA5

5.0 ns

4.6 ns

Propagation delay bus clock L-to-H to

12.0 ns

ata_cs0, ata_cs1, ata_da2, ata_da1, ata_da0, ata_dior, ata_diow, ata_dmack, ata_data,

ata_buffer_en

tsu

tsui

Set-up time ata_data to bus clock L-to-H

Set-up time ata_iordy to bus clock H-to-L

Hold time ata_iordy to bus clock H to L

8.5 ns

2.5 ns

7 ns

thi

tskew1

Max difference in propagation delay bus clock L-to-H to any of following signals

ata_cs0, ata_cs1, ata_da2, ata_da1, ata_da0, ata_dior, ata_diow, ata_dmack, ata_data

(write), ata_buffer_en

tskew2

tskew3

Max difference in buffer propagation delay for any of following signals

ata_cs0, ata_cs1, ata_da2, ata_da1, ata_da0, ata_dior, ata_diow, ata_dmack, ata_data

(write), ata_buffer_en

transceiver

Max difference in buffer propagation delay for any of following signals ata_iordy, ata_data

(read)

tbuf

Max buffer propagation delay

transceiver

cable

tcable1

tcable2

tskew4

Cable propagation delay for ata_data

Cable propagation delay for control signals ata_dior, ata_diow, ata_iordy, ata_dmack

Max difference in cable propagation delay between ata_iordy and ata_data (read)

cable

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

22

Freescale Semiconductor

Electrical Characteristics

Value/

Table 21. ATA Timing Parameters (continued)

Description

Name

1

Contributing Factor

tskew5

Max difference in cable propagation delay between (ata_dior, ata_diow, ata_dmack) and

ata_cs0, ata_cs1, ata_da2, ata_da1, ata_da0, ata_data(write)

cable

tskew6

Max difference in cable propagation delay without accounting for ground bounce

cable

1

Values provided where applicable.

4.3.5.2

PIO Mode Timing

Figure 10 shows timing for PIO read, and Table 22 lists the timing parameters for PIO read.

Figure 10. PIO Read Timing Diagram

Table 22. PIO Read Timing Parameters

ATA

Parameter

Controlling

Variable

Value

Parameter from Figure 10

t1

t2

t9

t5

t1

t2r

t9

t1 (min) = time_1 * T – (tskew1 + tskew2 + tskew5)

t2 min) = time_2r * T – (tskew1 + tskew2 + tskew5)

t9 (min) = time_9 * T – (tskew1 + tskew2 + tskew6)

t5 (min) = tco + tsu + tbuf + tbuf + tcable1 + tcable2

time_1

time_2r

time_3

t5

If not met, increase

time_2

t6

tA

t6

tA

0

—

tA (min) = (1.5 + time_ax) * T – (tco + tsui + tcable2 + tcable2 + 2*tbuf)

time_ax

trd

trd1

trd1 (max) = (–trd) + (tskew3 + tskew4)

time_pio_rdx

trd1 (min) = (time_pio_rdx – 0.5)*T – (tsu + thi)

(time_pio_rdx – 0.5) * T > tsu + thi + tskew3 + tskew4

t0

—

t0 (min) = (time_1 + time_2 + time_9) * T

time_1, time_2r, time_9

Figure 11 shows timing for PIO write, and Table 23 lists the timing parameters for PIO write.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

23

Electrical Characteristics

Figure 11. Multiword DMA (MDMA) Timing

Table 23. PIO Write Timing Parameters

ATA

Parameter

Controlling

Variable

Value

Parameter from Figure 11

t1

t2

t9

t3

t1

t2w

t9

t1 (min) = time_1 * T – (tskew1 + tskew2 + tskew5)

t2 (min) = time_2w * T – (tskew1 + tskew2 + tskew5)

t9 (min) = time_9 * T – (tskew1 + tskew2 + tskew6)

t3 (min) = (time_2w – time_on)* T – (tskew1 + tskew2 +tskew5)

time_1

time_2w

time_9

—

If not met, increase

time_2w

t4

tA

t0

t4

tA

—

t4 (min) = time_4 * T – tskew1

time_4

tA = (1.5 + time_ax) * T – (tco + tsui + tcable2 + tcable2 + 2*tbuf)

t0(min) = (time_1 + time_2 + time_9) * T

time_ax

time_1, time_2r,

time_9

—

Avoid bus contention when switching buffer on by making ton long enough.

Avoid bus contention when switching buffer off by making toff long enough.

—

Figure 12 shows timing for MDMA read, Figure 13 shows timing for MDMA write, and Table 24 lists the

timing parameters for MDMA read and write.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

24

Freescale Semiconductor

Electrical Characteristics

Figure 12. MDMA Read Timing Diagram

Figure 13. MDMA Write Timing Diagram

Table 24. MDMA Read and Write Timing Parameters

Parameter

from

Figure 12,

Figure 13

ATA

Parameter

Controlling

Variable

Value

tm, ti

tm

td, td1

tk

tm (min) = ti (min) = time_m * T – (tskew1 + tskew2 + tskew5)

td1.(min) = td (min) = time_d * T – (tskew1 + tskew2 + tskew6)

tk.(min) = time_k * T – (tskew1 + tskew2 + tskew6)

t0 (min) = (time_d + time_k) * T

time_m

time_d

td

tk

time_k

t0

—

time_d, time_k

time_d

tg(read)

tgr

tgr (min-read) = tco + tsu + tbuf + tbuf + tcable1 + tcable2

tgr.(min-drive) = td – te(drive)

tf(read)

tg(write)

tf(write)

tL

tfr

—

tfr (min-drive) = 0

—

time_d

tg (min-write) = time_d * T – (tskew1 + tskew2 + tskew5)

tf (min-write) = time_k * T – (tskew1 + tskew2 + tskew6)

tL (max) = (time_d + time_k–2)*T – (tsu + tco + 2*tbuf + 2*tcable2)

—

time_k

—

time_d, time_k

tn, tj

tkjn

tn= tj= tkjn = (max(time_k,. time_jn) * T – (tskew1 + tskew2 + tskew6)

time_jn

—

ton

toff

ton = time_on * T – tskew1

toff = time_off * T – tskew1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

25

Electrical Characteristics

4.3.5.3

UDMA In Timing

Figure 14 shows timing when the UDMA in transfer starts, Figure 15 shows timing when the UDMA in

host terminates transfer, Figure 16 shows timing when the UDMA in device terminates transfer, and

Table 25 lists the timing parameters for UDMA in burst.

Figure 14. UDMA In Transfer Starts Timing Diagram

Figure 15. UDMA In Host Terminates Transfer Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

26

Freescale Semiconductor

Electrical Characteristics

Figure 16. UDMA In Device Terminates Transfer Timing Diagram

Table 25. UDMA In Burst Timing Parameters

Parameter

from

Figure 14,

Figure 15,

Figure 16

ATA

Parameter

Description

Controlling Variable

tack

tenv

tack

tenv

tack (min) = (time_ack * T) – (tskew1 + tskew2)

time_ack

time_env

tenv (min) = (time_env * T) – (tskew1 + tskew2)

tenv (max) = (time_env * T) + (tskew1 + tskew2)

tds

tdh

tds1

tdh1

tc1

tds – (tskew3) – ti_ds > 0

tskew3, ti_ds, ti_dh

should be low enough

tdh – (tskew3) – ti_dh > 0

tcyc

trp

(tcyc – tskew) > T

T big enough

time_rp

trp

trp (min) = time_rp * T – (tskew1 + tskew2 + tskew6)

(time_rp * T) – (tco + tsu + 3T + 2 *tbuf + 2*tcable2) > trfs (drive)

tmli1 (min) = (time_mlix + 0.4) * T

1

—

tx1

time_rp

tmli

tzah

tdzfs

tcvh

—

tmli1

tzah

tdzfs

tcvh

time_mlix

time_zah

time_dzfs

time_cvh

—

tzah (min) = (time_zah + 0.4) * T

tdzfs = (time_dzfs * T) – (tskew1 + tskew2)

tcvh = (time_cvh *T) – (tskew1 + tskew2)

ton

toff

ton = time_on * T – tskew1

toff = time_off * T – tskew1

1

There is a special timing requirement in the ATA host that requires the internal DIOW to go only high 3 clocks after the last

active edge on the DSTROBE signal. The equation given on this line tries to capture this constraint.

2. Make ton and toff big enough to avoid bus contention

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

27

Electrical Characteristics

4.3.5.4 UDMA Out Timing

Figure 17 shows timing when the UDMA out transfer starts, Figure 18 shows timing when the UDMA out

host terminates transfer, Figure 19 shows timing when the UDMA out device terminates transfer, and

Table 26 lists the timing parameters for UDMA out burst.

Figure 17. UDMA Out Transfer Starts Timing Diagram

Figure 18. UDMA Out Host Terminates Transfer Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

28

Freescale Semiconductor

Electrical Characteristics

Figure 19. UDMA Out Device Terminates Transfer Timing Diagram

Table 26. UDMA Out Burst Timing Parameters

Parameter

from

Figure 17,

Figure 18,

Figure 19

ATA

Parameter

Controlling

Variable

Value

tack

tenv

tack

tenv

tack (min) = (time_ack * T) – (tskew1 + tskew2)

time_ack

time_env

tenv (min) = (time_env * T) – (tskew1 + tskew2)

tenv (max) = (time_env * T) + (tskew1 + tskew2)

tdvs

tdvh

tcyc

t2cyc

trfs1

—

tdvs

tdvh

tcyc

—

tdvs = (time_dvs * T) – (tskew1 + tskew2)

tdvs = (time_dvh * T) – (tskew1 + tskew2)

tcyc = time_cyc * T – (tskew1 + tskew2)

t2cyc = time_cyc * 2 * T

time_dvs

time_dvh

time_cyc

—

trfs

trfs = 1.6 * T + tsui + tco + tbuf + tbuf

tdzfs = time_dzfs * T – (tskew1)

tss = time_ss * T – (tskew1 + tskew2)

tdzfs_mli =max (time_dzfs, time_mli) * T – (tskew1 + tskew2)

tli1 > 0

tdzfs

tss

time_dzfs

time_ss

—

tss

tmli

tli

tdzfs_mli

tli1

—

tli

tli2

tli2 > 0

—

tli

tli3

tli3 > 0

—

tcvh

—

tcvh

tcvh = (time_cvh *T) – (tskew1 + tskew2)

time_cvh

—

ton

toff

ton = time_on * T – tskew1

toff = time_off * T – tskew1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

29

Electrical Characteristics

4.3.6

AUDMUX Electrical Specifications

The AUDMUX provides a programmable interconnect logic for voice, audio and data routing between

internal serial interfaces (SSI) and external serial interfaces (audio and voice codecs). The AC timing of

AUDMUX external pins is hence governed by the SSI module. Please refer to their respective electrical

specifications.

4.3.7

CSPI Electrical Specifications

This section describes the electrical information of the CSPI.

4.3.7.1 CSPI Timing

Figure 20 and Figure 21 depict the master mode and slave mode timings of CSPI, and Table 27 lists the

timing parameters.

SPI_RDY

CS11

SSx

CS2

CS6

CS1

CS3

CS5

CS3

CS4

SCLK

MOSI

MISO

CS2

CS7 CS8

CS9

CS10

Figure 20. CSPI Master Mode Timing Diagram

SSx

CS2

CS6

CS1

CS3

CS5

CS3

CS4

SCLK

CS2

CS7 CS8

MISO

MOSI

CS9

CS10

Figure 21. CSPI Slave Mode Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

30

Freescale Semiconductor

Electrical Characteristics

Table 27. CSPI Interface Timing Parameters

Parameter Symbol

ID

Min

Max

Units

CS1

CS2

CS3

CS4

CS5

CS6

CS7

CS8

CS9

CS10

CS11

SCLK Cycle Time

t

60

30

—

25

5

—

7.6

—

ns

clk

SCLK High or Low Time

SCLK Rise or Fall

t

SW

RISE/FALL

t

SSx pulse width

t

CSLH

SSx Lead Time (CS setup time)

SSx Lag Time (CS hold time)

Data Out Setup Time

Data Out Hold Time

t

SCS

HCS

t

Smosi

Hmosi

Smiso

Hmiso

5

Data In Setup Time

6

Data In Hold Time

5

1

SPI_RDY Setup Time

t

—

SRDY

1

SPI_RDY is sampled internally by ipg_clk and is asynchronous to all other CSPI signals.

4.3.8

DPLL Electrical Specifications

The three PLL’s of the MCIMX31C (MCU, USB, and Serial PLL) are all based on same DPLL design.

The characteristics provided herein apply to all of them, except where noted explicitly. The PLL

characteristics are provided based on measurements done for both sources—external clock source (CKIH),

and FPM (Frequency Pre-Multiplier) source.

4.3.8.1

Electrical Specifications

Table 28 lists the DPLL specification.

Table 28. DPLL Specifications

Parameter

Min

Typ

Max Unit

Comments

1

2

CKIH frequency

15

—

26

75

—

MHz

—

CKIL frequency

(Frequency Pre-multiplier (FPM) enable mode)

32; 32.768, 38.4

kHz FPM lock time ≈ 480 µs.

Predivision factor (PD bits)

1

—

16

35

—

PLL reference frequency range after Predivider

15

MHz 15 ≤ CKIH frequency/PD ≤ 35 MHz

15 ≤ FPM output/PD ≤ 35 MHz

PLL output frequency range:

—

MPLL and SPLL 52

UPLL 190

400 MHz

240

—

Maximum allowed reference clock phase noise.

—

100 ps

—

Frequency lock time

398

—

Cycles of divided reference clock.

(FOL mode or non-integer MF)

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

31

Electrical Characteristics

Table 28. DPLL Specifications (continued)

Parameter

Min

Typ

Max Unit

Comments

Phase lock time

—

100

25

µs In addition to the frequency

Maximum allowed PLL supply voltage ripple

PLL output clock phase jitter

mV

F

< 50 kHz

modulation

20

mV 50 kHz < F

< 300 kHz

modulation

25

mV

F

> 300 kHz

modulation

5.2

420

ns Measured on CLKO pin

ps Measured on CLKO pin

PLL output clock period jitter

1

2

The user or board designer must take into account that the use of a frequency other than 26 MHz would require adjustment to

the DPTC–DVFS table, which is incorporated into operating system code.

The PLL reference frequency must be ≤ 35 MHz. Therefore, for frequencies between 35 MHz and 70 MHz, program the

predivider to divide by 2 or more. If the CKIH frequency is above 70 MHz, program the predivider to 3 or more. For PD bit

description, see the reference manual.

4.3.9

EMI Electrical Specifications

This section provides electrical parametrics and timings for EMI module.

4.3.9.1 NAND Flash Controller Interface (NFC)

The NFC supports normal timing mode, using two flash clock cycles for one access of RE and WE. AC

timings are provided as multiplications of the clock cycle and fixed delay. Figure 22, Figure 23, Figure 24,

and Figure 25 depict the relative timing requirements among different signals of the NFC at module level,

for normal mode, and Table 29 lists the timing parameters.

NFCLE

NF2

NF1

NF3

NF4

NFCE

NF5

NFWE

NFALE

NF6

NF7

NF8

NF9

Command

NFIO[7:0]

Figure 22. Command Latch Cycle Timing DIagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

32

Freescale Semiconductor

Electrical Characteristics

NFCLE

NFCE

NF1

NF3

NF4

NF10

NF11

NF5

NF8

NFWE

NFALE

NF7

NF9

NF6

NFIO[7:0]

Address

Figure 23. Address Latch Cycle Timing DIagram

NFCLE

NFCE

NF1

NF3

NF10

NF11

NF5

NFWE

NFALE

NF7

NF6

NF8

NF9

NFIO[15:0]

Data to NF

Figure 24. Write Data Latch Cycle Timing DIagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

33

Electrical Characteristics

NFCLE

NFCE

NF14

NF13

NF15

NFRE

NFRB

NF17

NF16

NF12

NFIO[15:0]

Data from NF

Figure 25. Read Data Latch Cycle Timing DIagram

1

Table 29. NFC Timing Parameters

Example Timing for

Timing

T = NFC Clock Cycle

^{NFC Clock}≈ 33 MHz

2

ID

Parameter

Symbol

Unit

T = 30 ns

Min

Max

Min

Max

NF1 NFCLE Setup Time

NF2 NFCLE Hold Time

NF3 NFCE Setup Time

NF4 NFCE Hold Time

NF5 NF_WP Pulse Width

NF6 NFALE Setup Time

NF7 NFALE Hold Time

NF8 Data Setup Time

NF9 Data Hold Time

tCLS

tCLH

tCS

T–1.0 ns

T–2.0 ns

T–1.0 ns

T–2.0 ns

—

29

28

29

28

—

ns

tCH

tWP

tALS

tALH

tDS

T–1.5 ns

28.5

T

—

30

27

30

25

—

T–3.0 ns

T

tDH

T–5.0 ns

NF10 Write Cycle Time

NF11 NFWE Hold Time

NF12 Ready to NFRE Low

NF13 NFRE Pulse Width

NF14 READ Cycle Time

NF15 NFRE High Hold Time

NF16 Data Setup on READ

NF17 Data Hold on READ

tWC

tWH

tRR

2T

T–2.5 ns

60

27.5

6T

1.5T

2T

—

180

45

—

tRP

tRC

60

tREH

tDSR

tDHR

0.5T–2.5 ns

N/A

12.5

10

N/A

0

1

2

The flash clock maximum frequency is 50 MHz.

Subject to DPLL jitter specification on Table 28, "DPLL Specifications," on page 31.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

34

Freescale Semiconductor

Electrical Characteristics

NOTE

High is defined as 80% of signal value and low is defined as 20% of signal

value.

NOTE

Timing for HCLK is 133 MHz and internal NFC clock (flash clock) is

approximately 33 MHz (30 ns). All timings are listed according to this NFC

clock frequency (multiples of NFC clock phases), except NF16 and NF17,

which are not NFC clock related.

4.3.9.2

Wireless External Interface Module (WEIM)

All WEIM output control signals may be asserted and deasserted by internal clock related to BCLK rising

edge or falling edge according to corresponding assertion/negation control fields. Address always begins

related to BCLK falling edge but may be ended both on rising and falling edge in muxed mode according

to control register configuration. Output data begins related to BCLK rising edge except in muxed mode

where both rising and falling edge may be used according to control register configuration. Input data,

ECB and DTACK all captured according to BCLK rising edge time. Figure 26 depicts the timing of the

WEIM module, and Table 30 lists the timing parameters.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

35

Electrical Characteristics

WEIM Outputs Timing

WE22

WE21

WE23

...

BCLK

WE1

WE2

Address

CS[x]

WE3

WE5

WE4

WE6

RW

WE7

WE9

WE8

OE

WE10

EB[x]

WE11

WE13

WE12

WE14

LBA

Output Data

WEIM Inputs Timing

BCLK

WE16

Input Data

ECB

WE15

WE18

WE20

WE17

DTACK

WE19

Figure 26. WEIM Bus Timing Diagram

Table 30. WEIM Bus Timing Parameters

Parameter

ID

Min

Max

Unit

WE1

WE2

WE3

WE4

WE5

WE6

WE7

Clock fall to Address Valid

Clock rise/fall to Address Invalid

–0.5

–3

2.5

5

ns

Clock rise/fall to CS[x] Valid

Clock rise/fall to CS[x] Invalid

Clock rise/fall to RW Valid

Clock rise/fall to RW Invalid

Clock rise/fall to OE Valid

3

–3

3

–3

3

–3

3

–3

3

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

36

Freescale Semiconductor

Electrical Characteristics

Table 30. WEIM Bus Timing Parameters (continued)

ID

Parameter

Min

Max

Unit

WE8

WE9

Clock rise/fall to OE Invalid

Clock rise/fall to EB[x] Valid

–3

3

ns

WE10 Clock rise/fall to EB[x] Invalid

WE11 Clock rise/fall to LBA Valid

–3

3

–3

3

WE12 Clock rise/fall to LBA Invalid

WE13 Clock rise/fall to Output Data Valid

WE14 Clock rise to Output Data Invalid

–3

3

–2.5

4

WE15 Input Data Valid to Clock rise, FCE=0

FCE=1

8

2.5

—

ns

WE16 Clock rise to Input Data Invalid, FCE=0

FCE=1

–2

—

WE17 ECB setup time, FCE=0

FCE=1

6.5

3.5

WE18 ECB hold time, FCE=0

FCE=1

–2

2

1

WE19 DTACK setup time

0

—

ns

1

WE20 DTACK hold time

4.5

—

2, 3

WE21 BCLK High Level Width

T/2 – 3

—

2, 3

WE22 BCLK Low Level Width

—

2

WE23 BCLK Cycle time

15

1

2

3

Applies to rising edge timing

BCLK parameters are being measured from the 50% VDD.

The actual cycle time is derived from the AHB bus clock frequency.

NOTE

High is defined as 80% of signal value and low is defined as 20% of signal

value.

Test conditions: load capacitance, 25 pF. Recommended drive strength for all

controls, address, and BCLK is Max drive.

Figure 27, Figure 28, Figure 29, Figure 30, Figure 31, and Figure 32 depict some examples of

basic WEIM accesses to external memory devices with the timing parameters mentioned in

Table 30 for specific control parameter settings.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

37

Electrical Characteristics

BCLK

WE2

WE1

WE3

V1

Next Address

WE4

Last Valid Address

ADDR

CS[x]

RW

WE11

WE12

WE8

LBA

WE7

WE9

OE

WE10

WE16

EB[y]

V1

WE15

DATA

Figure 27. Asynchronous Memory Timing Diagram for Read Access—WSC=1

BCLK

WE2

WE1

Last Valid Address

ADDR

CS[x]

Next Address

V1

WE3

WE5

WE4

WE6

RW

LBA

OE

WE11

WE12

WE10

WE9

EB[y]

DATA

WE14

V1

WE13

Figure 28. Asynchronous Memory Timing Diagram for Write Access—

WSC=1, EBWA=1, EBWN=1, LBN=1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

38

Freescale Semiconductor

Electrical Characteristics

BCLK

WE1

Last Valid Addr

WE3

WE2

Address V1

Address V2

ADDR

CS[x]

WE4

RW

WE11

WE7

WE12

LBA

WE8

OE

WE10

WE9

EB[y]

WE18

WE17

ECB

WE17

V1+2

WE16

V1

WE16

WE15

V2

Halfword

V2+2

Halfword

DATA

Halfword Halfword

WE15

Figure 29. Synchronous Memory Timing Diagram for Two Non-Sequential Read Accesses—

WSC=2, SYNC=1, DOL=0

BCLK

WE2

WE4

WE6

WE1

ADDR

Last Valid Addr

Address V1

WE3

CS[x]

WE5

RW

WE12

WE11

LBA

OE

WE10

WE9

EB[y]

WE18

ECB

WE17

V1

WE14

WE13

V1+4 V1+8 V1+12

DATA

WE13

Figure 30. Synchronous Memory TIming Diagram for Burst Write Access—

BCS=1, WSC=4, SYNC=1, DOL=0, PSR=1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

39

Electrical Characteristics

BCLK

WE1

WE2

WE14

WE4

WE6

ADDR/

M_DATA

Last Valid Addr

Write Data

Address V1

WE13

WE3

CS[x]

RW

WE5

Write

WE11

WE12

LBA

OE

WE9

WE10

EB[y]

Figure 31. Muxed A/D Mode Timing Diagram for Asynchronous Write Access—

WSC=7, LBA=1, LBN=1, LAH=1

BCLK

WE16

WE2

WE1

Last Valid Addr

WE3

ADDR/

M_DATA

Address V1

Read Data

WE15

CS[x]

WE4

RW

WE11

WE12

LBA

WE7

WE8

OE

WE9

WE10

EB[y]

Figure 32. Muxed A/D Mode Timing Diagram for Asynchronous Read Access—

WSC=7, LBA=1, LBN=1, LAH=1, OEA=7

4.3.9.3

ESDCTL Electrical Specifications

Figure 33, Figure 34, Figure 35, Figure 36, Figure 37, and Figure 38 depict the timings pertaining to the

ESDCTL module, which interfaces Mobile DDR or SDR SDRAM. Table 31, Table 32, Table 33, Table 34,

Table 35, and Table 36 list the timing parameters.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

40

Freescale Semiconductor

Electrical Characteristics

SD1

SDCLK

SD2

SD3

SD4

CS

RAS

CAS

SD5

SD4

SD5

SD4

SD5

WE

ADDR

DQ

SD6

SD7

ROW/BA

COL/BA

SD8

SD10

SD9

Data

SD4

DQM

Note: CKE is high during the read/write cycle.

Figure 33. SDRAM Read Cycle Timing Diagram

Table 31. DDR/SDR SDRAM Read Cycle Timing Parameters

SD5

ID

Parameter

Symbol

Min

Max

Unit

SD1

SD2

SD3

SD4

SD5

SD6

SD7

SD8

SDRAM clock high-level width

SDRAM clock low-level width

SDRAM clock cycle time

tCH

tCL

3.4

7.5

2.0

1.8

2.0

1.8

—

4.1

—

ns

tCK

CS, RAS, CAS, WE, DQM, CKE setup time

CS, RAS, CAS, WE, DQM, CKE hold time

Address setup time

tCMS

tCMH

tAS

—

Address hold time

tAH

—

SDRAM access time

tAC

6.47

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

41

Electrical Characteristics

Table 31. DDR/SDR SDRAM Read Cycle Timing Parameters (continued)

ID

Parameter

Symbol

Min

Max

Unit

1

SD9

Data out hold time

Active to read/write command period

tOH

tRC

1.8

10

—

ns

SD10

clock

1

Timing parameters are relevant only to SDR SDRAM. For the specific DDR SDRAM data related timing parameters, see

Table 35 and Table 36.

NOTE

SDR SDRAM CLK parameters are being measured from the 50%

point—that is, high is defined as 50% of signal value and low is defined as

50% of signal value. SD1 + SD2 does not exceed 7.5 ns for 133 MHz.

NOTE

The timing parameters are similar to the ones used in SDRAM data

sheets—that is, Table 31indicates SDRAM requirements. All output signals

are driven by the ESDCTL at the negative edge of SDCLK and the

parameters are measured at maximum memory frequency.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

42

Freescale Semiconductor

Electrical Characteristics

SD1

SDCLK

SD2

SD4

SD3

CS

SD5

RAS

CAS

SD11

SD4

SD5

SD4

WE

SD5

SD12

SD7

SD6

BA

ADDR

COL/BA

DATA

ROW / BA

SD13

SD14

DQ

DQM

Figure 34. SDR SDRAM Write Cycle Timing Diagram

Table 32. SDR SDRAM Write Timing Parameters

ID

Parameter

Symbol

Min

Max

Unit

SD1

SD2

SD3

SD4

SD5

SD6

SD7

SD11

SD12

SDRAM clock high-level width

SDRAM clock low-level width

SDRAM clock cycle time

tCH

tCL

3.4

7.5

2.0

1.8

2.0

1.8

1

4.1

—

4

ns

tCK

ns

CS, RAS, CAS, WE, DQM, CKE setup time

CS, RAS, CAS, WE, DQM, CKE hold time

Address setup time

tCMS

tCMH

tAS

ns

Address hold time

tAH

ns

1

Precharge cycle period

tRP

clock

1

Active to read/write command delay

tRCD

1

8

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

43

Electrical Characteristics

Table 32. SDR SDRAM Write Timing Parameters (continued)

ID

Parameter

Symbol

Min

Max

Unit

SD13

SD14

Data setup time

Data hold time

tDS

tDH

2.0

1.3

—

ns

1

SD11 and SD12 are determined by SDRAM controller register settings.

NOTE

SDR SDRAM CLK parameters are being measured from the 50%

point—that is, high is defined as 50% of signal value and low is defined as

50% of signal value.

NOTE

The timing parameters are similar to the ones used in SDRAM data

sheets—that is, Table 32indicates SDRAM requirements. All output signals

are driven by the ESDCTL at the negative edge of SDCLK and the

parameters are measured at maximum memory frequency.

SD1

SDCLK

SD2

SD3

CS

RAS

CAS

SD11

SD10

WE

SD7

SD6

BA

ADDR

ROW/BA

Figure 35. SDRAM Refresh Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

44

Freescale Semiconductor

Electrical Characteristics

Table 33. SDRAM Refresh Timing Parameters

ID

Parameter

Symbol

Min

Max

Unit

SD1

SD2

SDRAM clock high-level width

SDRAM clock low-level width

SDRAM clock cycle time

Address setup time

tCH

tCL

tCK

tAS

tAH

tRP

tRC

3.4

7.5

1.8

1

4.1

—

4

ns

SD3

ns

SD6

ns

SD7

Address hold time

ns

1

SD10

SD11

Precharge cycle period

clock

1

Auto precharge command period

2

20

1

SD10 and SD11 are determined by SDRAM controller register settings.

NOTE

SDR SDRAM CLK parameters are being measured from the 50%

point—that is, high is defined as 50% of signal value and low is defined as

50% of signal value.

NOTE

The timing parameters are similar to the ones used in SDRAM data

sheets—that is, Table 33indicates SDRAM requirements. All output signals

are driven by the ESDCTL at the negative edge of SDCLK and the

parameters are measured at maximum memory frequency.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

45

Electrical Characteristics

SDCLK

CS

RAS

CAS

WE

ADDR

CKE

BA

SD16

Don’t care

Figure 36. SDRAM Self-Refresh Cycle Timing Diagram

NOTE

The clock will continue to run unless both CKEs are low. Then the clock

will be stopped in low state.

Table 34. SDRAM Self-Refresh Cycle Timing Parameters

ID

SD16

Parameter

CKE output delay time

Symbol

Min

Max

Unit

tCKS

1.8

—

ns

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

46

Freescale Semiconductor

Electrical Characteristics

SDCLK

SD20

SD19

DQS (output)

DQ (output)

SD18

Data

SD17

Data

SD17

SD18

Data

DM

Data

DM

Data

DM

DQM (output)

DM

SD17

SD18

Figure 37. Mobile DDR SDRAM Write Cycle Timing Diagram

Table 35. Mobile DDR SDRAM Write Cycle Timing Parameters

1

ID

Parameter

Symbol

Min

Max Unit

SD17 DQ & DQM setup time to DQS

SD18 DQ & DQM hold time to DQS

tDS

tDH

0.95

1.8

—

ns

SD19 Write cycle DQS falling edge to SDCLK output delay time.

SD20 Write cycle DQS falling edge to SDCLK output hold time.

tDSS

tDSH

1.8

1

Test condition: Measured using delay line 5 programmed as follows: ESDCDLY5[15:0] = 0x0703.

NOTE

SDRAM CLK and DQS related parameters are being measured from the

50% point—that is, high is defined as 50% of signal value and low is

defined as 50% of signal value.

NOTE

The timing parameters are similar to the ones used in SDRAM data

sheets—that is, Table 35indicates SDRAM requirements. All output signals

are driven by the ESDCTL at the negative edge of SDCLK and the

parameters are measured at maximum memory frequency.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

47

Electrical Characteristics

SDCLK

SD23

DQS (input)

DQ (input)

SD22

Data

SD21

Data

Figure 38. Mobile DDR SDRAM DQ versus DQS and SDCLK Read Cycle Timing Diagram

Table 36. Mobile DDR SDRAM Read Cycle Timing Parameters

ID

Parameter

Symbol Min Max Unit

SD21 DQS – DQ Skew (defines the Data valid window in read cycles related to DQS).

SD22 DQS DQ HOLD time from DQS

tDQSQ

tQH

—

2.3

—

0.85 ns

—

ns

SD23 DQS output access time from SDCLK posedge

tDQSCK

6.7

NOTE

SDRAM CLK and DQS related parameters are being measured from the

50% point—that is, high is defined as 50% of signal value and low is

defined as 50% of signal value.

NOTE

The timing parameters are similar to the ones used in SDRAM data

sheets—that is, Table 36indicates SDRAM requirements. All output signals

are driven by the ESDCTL at the negative edge of SDCLK and the

parameters are measured at maximum memory frequency.

4.3.10 ETM Electrical Specifications

ETM is an ARM protocol. The timing specifications in this section are given as a guide for a TPA that

supports TRACECLK frequencies up to 133 MHz.

Figure 39 depicts the TRACECLK timings of ETM, and Table 37 lists the timing parameters.

Figure 39. ETM TRACECLK Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

48

Freescale Semiconductor

Electrical Characteristics

Table 37. ETM TRACECLK Timing Parameters

ID

Parameter

Min

Max

Unit

T

Clock period

Frequency dependent

—

3

ns

cyc

T

Low pulse width

2

wl

T

High pulse width

wh

T

Clock and data rise time

Clock and data fall time

—

r

T

3

f

Figure 40 depicts the setup and hold requirements of the trace data pins with respect to TRACECLK, and

Table 38 lists the timing parameters.

Figure 40. Trace Data Timing Diagram

Table 38. ETM Trace Data Timing Parameters

ID

Parameter

Min

Max

Unit

T

Data setup

Data hold

2

1

—

ns

s

h

4.3.10.1 Half-Rate Clocking Mode

When half-rate clocking is used, the trace data signals are sampled by the TPA on both the rising and

falling edges of TRACECLK, where TRACECLK is half the frequency of the clock shown in Figure 40.

4.3.11 FIR Electrical Specifications

®

FIR implements asynchronous infrared protocols (FIR, MIR) that are defined by IrDA (Infrared Data

Association). Refer to http://www.IrDA.org for details on FIR and MIR protocols.

4.3.12 Fusebox Electrical Specifications

Table 39. Fusebox Timing Characteristics

Ref. Num

Description

Symbol

Minimum

Typical

Maximum

Units

1

Program time for eFuse

t

125

—

µs

program

1

The program length is defined by the value defined in the epm_pgm_length[2:0] bits of the IIM module. The value to program

is based on a 32 kHz clock source (4 * 1/32 kHz = 125 µs)

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

49

Electrical Characteristics

4.3.13 I²C Electrical Specifications

2

This section describes the electrical information of the I C Module.

4.3.13.1 I²C Module Timing

2

Figure 41 depicts the timing of I C module. Table 40 lists the I C module timing parameters where the I/O

supply is 2.7 V. 1

IC11

IC9

IC10

I2DAT

I2CLK

IC7

IC4

IC2

IC3

IC8

IC10

IC6

IC11

STOP

START

IC5

IC1

2

Figure 41. I C Bus Timing Diagram

2

Table 40. I C Module Timing Parameters—I C Pin I/O Supply=2.7 V

Standard Mode

Fast Mode

Min Max

ID

IC1 I2CLK cycle time

Parameter

Unit

Min

Max

10

4.0

—

2.5

0.6

—

0.9

—

μs

ns

μs

ns

pF

IC2 Hold time (repeated) START condition

IC3 Set-up time for STOP condition

IC4 Data hold time

1

2

1

2

0

3.45

—

0

IC5 HIGH Period of I2CLK Clock

4.0

4.7

250

4.7

—

0.6

1.3

0.6

IC6 LOW Period of the I2CLK Clock

IC7 Set-up time for a repeated START condition

IC8 Data set-up time

—

3

—

100

1.3

IC9 Bus free time between a STOP and START condition

IC10 Rise time of both I2DAT and I2CLK signals

IC11 Fall time of both I2DAT and I2CLK signals

—

4

1000

300

400

20+0.1C

—

300

400

b

—

IC12 Capacitive load for each bus line (C )

—

b

1

A device must internally provide a hold time of at least 300 ns for I2DAT signal in order to bridge the undefined region of the

falling edge of I2CLK.

2

3

The maximum hold time has to be met only if the device does not stretch the LOW period (ID IC6) of the I2CLK signal.

2

A Fast-mode I C-bus device can be used in a standard-mode I C-bus system, but the requirement of set-up time (ID IC7) of

250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the I2CLK signal.

If such a device does stretch the LOW period of the I2CLK signal, it must output the next data bit to the I2DAT line max_rise_time

2

(ID No IC10) + data_setup_time (ID No IC8) = 1000 + 250 = 1250 ns (according to the Standard-mode I C-bus specification)

before the I2CLK line is released.

4

C = total capacitance of one bus line in pF.

b

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

50

Freescale Semiconductor

Electrical Characteristics

4.3.14 IPU—Sensor Interfaces

4.3.14.1 Supported Camera Sensors

Table 41 lists the known supported camera sensors at the time of publication.

1

Table 41. Supported Camera Sensors

Vendor

Model

2

Conexant

Agilant

CX11646, CX20490 , CX20450

2

HDCP–2010, ADCS–1021 , ADCS–1021

TC90A70

Toshiba

ICMedia

iMagic

2

ICM202A, ICM102

IM8801

Transchip

Fujitsu

TC5600, TC5600J, TC5640, TC5700, TC6000

MB86S02A

MI–SOC–0133

MN39980

Micron

Matsushita

STMicro

OmniVision

Sharp

2

W6411, W6500, W6501 , W6600 , W6552 , STV0974

OV7620, OV6630

LZ0P3714 (CCD)

2

Motorola

MC30300 (Python) , SCM20014 , SCM20114 , SCM22114 , SCM20027

2

National Semiconductor

LM9618

1

2

Freescale Semiconductor does not recommend one supplier over another and in no way suggests that these are the only

camera suppliers.

These sensors not validated at time of publication.

4.3.14.2 Functional Description

There are three timing modes supported by the IPU.

4.3.14.2.1 Pseudo BT.656 Video Mode

Smart camera sensors, which include imaging processing, usually support video mode transfer. They use

an embedded timing syntax to replace the SENSB_VSYNC and SENSB_HSYNC signals. The timing

syntax is defined by the BT.656 standard.

This operation mode follows the recommendations of ITU BT.656 specifications. The only control signal

used is SENSB_PIX_CLK. Start-of-frame and active-line signals are embedded in the data stream. An

active line starts with a SAV code and ends with a EAV code. In some cases, digital blanking is inserted in

between EAV and SAV code. The CSI decodes and filters out the timing-coding from the data stream, thus

recovering SENSB_VSYNC and SENSB_HSYNC signals for internal use.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

51

Electrical Characteristics

4.3.14.2.2 Gated Clock Mode

The SENSB_VSYNC, SENSB_HSYNC, and SENSB_PIX_CLK signals are used in this mode. See

Figure 42.

Active Line

Start of Frame

nth frame

n+1th frame

SENSB_VSYNC

SENSB_HSYNC

SENSB_PIX_CLK

invalid

SENSB_DATA[9:0]

1st byte

Figure 42. Gated Clock Mode Timing Diagram

A frame starts with a rising edge on SENSB_VSYNC (all the timings correspond to straight polarity of the

corresponding signals). Then SENSB_HSYNC goes to high and hold for the entire line. Pixel clock is

valid as long as SENSB_HSYNC is high. Data is latched at the rising edge of the valid pixel clocks.

SENSB_HSYNC goes to low at the end of line. Pixel clocks then become invalid and the CSI stops

receiving data from the stream. For next line the SENSB_HSYNC timing repeats. For next frame the

SENSB_VSYNC timing repeats.

4.3.14.2.3 Non-Gated Clock Mode

The timing is the same as the gated-clock mode (described in Section 4.3.14.2.2, “Gated Clock Mode,” on

page 52), except for the SENSB_HSYNC signal, which is not used. See Figure 43. All incoming pixel

clocks are valid and will cause data to be latched into the input FIFO. The SENSB_PIX_CLK signal is

inactive (states low) until valid data is going to be transmitted over the bus.

Start of Frame

nth frame

n+1th frame

SENSB_VSYNC

SENSB_PIX_CLK

invalid

SENSB_DATA[7:0]

1st byte

Figure 43. Non-Gated Clock Mode Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

52

Freescale Semiconductor

Electrical Characteristics

The timing described in Figure 43 is that of a Motorola sensor. Some other sensors may have a slightly

different timing. The CSI can be programmed to support rising/falling-edge triggered SENSB_VSYNC;

active-high/low SENSB_HSYNC; and rising/falling-edge triggered SENSB_PIX_CLK.

4.3.14.3 Electrical Characteristics

Figure 44 depicts the sensor interface timing, and Table 42 lists the timing parameters.

1/IP1

SENSB_MCLK

(Sensor Input)

SENSB_PIX_CLK

(Sensor Output)

1/IP4

IP2

IP3

SENSB_DATA,

SENSB_VSYNC,

SENSB_HSYNC

Figure 44. Sensor Interface Timing Diagram

Table 42. Sensor Interface Timing Parameters

1

ID

Parameter

Symbol

Min.

Max.

Units

IP1

IP2

IP3

Sensor input clock frequency

Data and control setup time

Fmck

Tsu

0.01

5

133

—

MHz

ns

Data and control holdup time

Sensor output (pixel) clock frequency

Thd

3

—

ns

IP4

Fpck

0.01

133

MHz

1

The timing specifications for Figure 43 are referenced to the rising edge of SENS_PIX_CLK when the

SENS_PIX_CLK_POL bit in the CSI_SENS_CONF register is cleared. When the SENS_PIX_CLK_POL is set,

the clock is inverted and all timing specifications will remain the same but are referenced to the falling edge of

the clock.

4.3.15 IPU—Display Interfaces

4.3.15.1 Supported Display Components

Table 43 lists the known supported display components at the time of publication.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

53

Electrical Characteristics

Type

1

Table 43. Supported Display Components

Vendor

Model

TFT displays

(memory-less)

Sharp (HR-TFT Super

Mobile LCD family)

LQ035Q7 DB02, LM019LC1Sxx

Samsung (QCIF and

QVGA TFT modules for

mobile phones)

LTS180S1-HF1, LTS180S3-HF1, LTS350Q1-PE1,

LTS350Q1-PD1, LTS220Q1-HE1

2

Toshiba (LTM series)

LTM022P806 , LTM04C380K ,

2

LTM018A02A , LTM020P332 , LTM021P337 , LTM019P334 ,

2

LTM022A783 , LTM022A05ZZ

NEC

NL6448BC20-08E, NL8060BC31-27

S1D15xxx series, S1D19xxx series, S1D13713, S1D13715

SSD1301 (OLED), SSD1828 (LDCD)

HD66766, HD66772

Display controllers

Epson

Solomon Systech

Hitachi

ATI

W2300

2

Smart display modules

Epson

L1F10043 T , L1F10044 T , L1F10045 T , L2D22002 , L2D20014 ,

2

L2F50032 , L2D25001 T

Hitachi

120 160 65K/4096 C-STN (#3284 LTD-1398-2) based on HD 66766

controller

Densitron Europe LTD

All displays with MPU 80/68K series interface and serial peripheral

interface

Sharp

LM019LC1Sxx

ACX506AKM

ADV7174/7179

CS49xx series

FS453/4

Sony

Digital video encoders

(for TV)

Analog Devices

Crystal (Cirrus Logic)

Focus

1

Freescale Semiconductor does not recommend one supplier over another and in no way suggests that these are the only

display component suppliers.

2

These display components not validated at time of publication.

4.3.15.2 Synchronous Interfaces

4.3.15.2.1 Interface to Active Matrix TFT LCD Panels, Functional Description

Figure 45 depicts the LCD interface timing for a generic active matrix color TFT panel. In this figure

signals are shown with negative polarity. The sequence of events for active matrix interface timing is:

•

DISPB_D3_CLK latches data into the panel on its negative edge (when positive polarity is

selected). In active mode, DISPB_D3_CLK runs continuously.

•

DISPB_D3_HSYNC causes the panel to start a new line.

DISPB_D3_VSYNC causes the panel to start a new frame. It always encompasses at least one

HSYNC pulse.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

54

Freescale Semiconductor

Electrical Characteristics

•

DISPB_D3_DRDY acts like an output enable signal to the CRT display. This output enables the

data to be shifted onto the display. When disabled, the data is invalid and the trace is off.

DISPB_D3_VSYNC

DISPB_D3_HSYNC

LINE 1

LINE 2

LINE 3

LINE 4

LINE n-1

LINE n

DISPB_D3_HSYNC

DISPB_D3_DRDY

1

2

3

m-1

m

DISPB_D3_CLK

DISPB_D3_DATA

Figure 45. Interface Timing Diagram for TFT (Active Matrix) Panels

4.3.15.2.2 Interface to Active Matrix TFT LCD Panels, Electrical Characteristics

Figure 46 depicts the horizontal timing (timing of one line), including both the horizontal sync pulse and

the data. All figure parameters shown are programmable. The timing images correspond to inverse polarity

of the DISPB_D3_CLK signal and active-low polarity of the DISPB_D3_HSYNC, DISPB_D3_VSYNC

and DISPB_D3_DRDY signals.

IP7

IP6

IP9

IP10

IP8

IP5

Start of line

DISPB_D3_CLK

DISPB_D3_HSYNC

DISPB_D3_DRDY

DISPB_D3_DATA

Figure 46. TFT Panels Timing Diagram—Horizontal Sync Pulse

Figure 47 depicts the vertical timing (timing of one frame). All figure parameters shown are

programmable.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

55

Electrical Characteristics

End of frame

Start of frame

IP13

DISPB_D3_VSYNC

DISPB_D3_HSYNC

DISPB_D3_DRDY

IP15

IP11

IP14

IP12

Figure 47. TFT Panels Timing Diagram—Vertical Sync Pulse

Table 44 shows timing parameters of signals presented in Figure 46 and Figure 47.

Table 44. Synchronous Display Interface Timing Parameters—Pixel Level

ID

Parameter

Symbol

Value

Units

1

IP5

IP6

Display interface clock period

Display pixel clock period

Screen width

Tdicp

Tdpcp

Tsw

Tdicp

ns

(DISP3_IF_CLK_CNT_D+1) * Tdicp

(SCREEN_WIDTH+1) * Tdpcp

(H_SYNC_WIDTH+1) * Tdpcp

BGXP * Tdpcp

IP7

IP8

HSYNC width

Thsw

Thbi1

Thbi2

Thsd

Tsh

IP9

Horizontal blank interval 1

Horizontal blank interval 2

HSYNC delay

IP10

IP11

IP12

IP13

(SCREEN_WIDTH – BGXP – FW) * Tdpcp

H_SYNC_DELAY * Tdpcp

Screen height

(SCREEN_HEIGHT+1) * Tsw

VSYNC width

Tvsw

if V_SYNC_WIDTH_L = 0 than

(V_SYNC_WIDTH+1) * Tdpcp

else

(V_SYNC_WIDTH+1) * Tsw

IP14

IP15

Vertical blank interval 1

Vertical blank interval 2

Tvbi1

Tvbi2

BGYP * Tsw

ns

(SCREEN_HEIGHT – BGYP – FH) * Tsw

1

Display interface clock period immediate value.

⎧

⎪

⎨

⎪

⎩

DISP3_IF_CLK_PER_WR

-----------------------------------------------------------------

DISP3_IF_CLK_PER_WR

-----------------------------------------------------------------

T

⋅

,

for integer

HSP_CLK

HSP_CLK_PERIOD

Tdicp =

DISP3_IF_CLK_PER_WR

⎛

⎞

-----------------------------------------------------------------

T

⋅ floor

+ 0.5 0.5 ,

for fractional

HSP_CLK

⎝

⎠

HSP_CLK_PERIOD

Display interface clock period average value.

DISP3_IF_CLK_PER_WR

-----------------------------------------------------------------

⋅

Tdicp = T

HSP_CLK

HSP_CLK_PERIOD

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

56

Freescale Semiconductor

Electrical Characteristics

NOTE

HSP_CLK is the High-Speed Port Clock, which is the input to the Image

Processing Unit (IPU). Its frequency is controlled by the Clock Control

Module (CCM) settings. The HSP_CLK frequency must be greater than or

equal to the AHB clock frequency.

The SCREEN_WIDTH, SCREEN_HEIGHT, H_SYNC_WIDTH, V_SYNC_WIDTH, BGXP, BGYP and

V_SYNC_WIDTH_L parameters are programmed via the SDC_HOR_CONF, SDC_VER_CONF,

SDC_BG_POS Registers. The FW and FH parameters are programmed for the corresponding DMA

channel. The DISP3_IF_CLK_PER_WR, HSP_CLK_PERIOD and DISP3_IF_CLK_CNT_D parameters

are programmed via the DI_DISP3_TIME_CONF, DI_HSP_CLK_PER and DI_DISP_ACC_CC

Registers.

Figure 48 depicts the synchronous display interface timing for access level, and Table 45 lists the timing

parameters. The DISP3_IF_CLK_DOWN_WR and DISP3_IF_CLK_UP_WR parameters are set via the

DI_DISP3_TIME_CONF Register.

IP20

DISPB_D3_VSYNC

DISPB_D3_HSYNC

DISPB_D3_DRDY

other controls

DISPB_D3_CLK

IP18

IP16

IP17

IP19

DISPB_DATA

Figure 48. Synchronous Display Interface Timing Diagram—Access Level

Table 45. Synchronous Display Interface Timing Parameters—Access Level

1

ID

Parameter

Symbol

Min

Typ

Max

Units

2

3

IP16 Display interface clock low time

Tckl

Tdicd–Tdicu–1.5

Tdicd –Tdicu

Tdicd–Tdicu+1.5

ns

IP17 Display interface clock high

time

Tckh Tdicp–Tdicd+Tdicu–1.5 Tdicp–Tdicd+Tdicu Tdicp–Tdicd+Tdicu+1.5

IP18 Data setup time

IP19 Data holdup time

Tdsu Tdicd–3.5

Tdicu

—

ns

Tdhd Tdicp–Tdicd–3.5

Tcsu Tdicd–3.5

Tdicp–Tdicu

Tdicu

IP20 Control signals setup time to

display interface clock

1

2

The exact conditions have not been finalized, but will likely match the current customer requirement for their specific display. These

conditions may be device specific.

Display interface clock down time

1

2

2 ⋅ DISP3_IF_CLK_DOWN_WR

--

--------------------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicd =

T

HSP_CLK_PERIOD

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

57

Electrical Characteristics

3

Display interface clock up time

1

2

2 ⋅ DISP3_IF_CLK_UP_WR

---------------------------------------------------------------------

⋅ ceil

HSP_CLK

--

Tdicu =

T

HSP_CLK_PERIOD

where CEIL(X) rounds the elements of X to the nearest integers towards infinity.

4.3.15.3 Interface to Sharp HR-TFT Panels

Figure 49 depicts the Sharp HR-TFT panel interface timing, and Table 46 lists the timing parameters. The

CLS_RISE_DELAY, CLS_FALL_DELAY, PS_FALL_DELAY, PS_RISE_DELAY,

REV_TOGGLE_DELAY parameters are defined in the SDC_SHARP_CONF_1 and

SDC_SHARP_CONF_2 registers. For other Sharp interface timing characteristics, refer to

Section 4.3.15.2.2, “Interface to Active Matrix TFT LCD Panels, Electrical Characteristics,” on page 55.

The timing images correspond to straight polarity of the Sharp signals.

Horizontal timing

DISPB_D3_CLK

D1 D2

D320

DISPB_D3_DATA

DISPB_D3_SPL

IP21

1 DISPB_D3_CLK period

DISPB_D3_HSYNC

IP23

IP22

DISPB_D3_CLS

DISPB_D3_PS

IP24

IP25

IP26

DISPB_D3_REV

Example is drawn with FW+1=320 pixel/line, FH+1=240 lines.

SPL pulse width is fixed and aligned to the first data of the line.

REV toggles every HSYNC period.

Figure 49. Sharp HR-TFT Panel Interface Timing Diagram—Pixel Level

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

58

Freescale Semiconductor

Electrical Characteristics

Table 46. Sharp Synchronous Display Interface Timing Parameters—Pixel Level

ID

Parameter

SPL rise time

Symbol

Value

(BGXP – 1) * Tdpcp

Units

IP21

IP22

IP23

IP24

IP25

IP26

Tsplr

Tclsr

Tclsf

Tpsf

Tpsr

Trev

ns

CLS rise time

CLS_RISE_DELAY * Tdpcp

CLS_FALL_DELAY * Tdpcp

PS_FALL_DELAY * Tdpcp

PS_RISE_DELAY * Tdpcp

REV_TOGGLE_DELAY * Tdpcp

CLS fall time

CLS rise and PS fall time

PS rise time

REV toggle time

4.3.15.4 Synchronous Interface to Dual-Port Smart Displays

Functionality and electrical characteristics of the synchronous interface to dual-port smart displays are

identical to parameters of the synchronous interface. See Section 4.3.15.2.2, “Interface to Active Matrix

TFT LCD Panels, Electrical Characteristics” on page 55.

4.3.15.4.1 Interface to a TV Encoder, Functional Description

The interface has an 8-bit data bus, transferring a single 8-bit value (Y/U/V) in each cycle. The bits

D7–D0 of the value are mapped to bits LD17–LD10 of the data bus, respectively. Figure 50 depicts the

interface timing,

•

The frequency of the clock DISPB_D3_CLK is 27 MHz (within 10%).

The DISPB_D3_HSYNC, DISPB_D3_VSYNC and DISPB_D3_DRDY signals are active low.

The transition to the next row is marked by the negative edge of the DISPB_D3_HSYNC signal.

It remains low for a single clock cycle.

•

The transition to the next field/frame is marked by the negative edge of the DISPB_D3_VSYNC

signal. It remains low for at least one clock cycle.

— At a transition to an odd field (of the next frame), the negative edges of DISPB_D3_VSYNC

and DISPB_D3_HSYNC coincide.

— At a transition to an even field (of the same frame), they do not coincide.

•

The active intervals—during which data is transferred—are marked by the DISPB_D3_HSYNC

signal being high.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

59

Electrical Characteristics

DISPB_D3_CLK

DISPB_D3_HSYNC

DISPB_D3_VSYNC

DISPB_D3_DRDY

DISPB_DATA

Cb

Y

Cr

Y

3

Cb

Y

Cr

Pixel Data Timing

523

524

525

1

2

4

5

6

10

DISPB_D3_HSYNC

DISPB_D3_DRDY

DISPB_D3_VSYNC

Even Field

262 263

Odd Field

268 269

261

264

265

266

267

273

DISPB_D3_HSYNC

DISPB_D3_DRDY

DISPB_D3_VSYNC

Even Field

Odd Field

Line and Field Timing - NTSC

621

622

623

624

625

1

2

3

4

23

DISPB_D3_HSYNC

DISPB_D3_DRDY

DISPB_D3_VSYNC

Even Field

Odd Field

315

308

309

310

311

312

313

314

316

336

DISPB_D3_HSYNC

DISPB_D3_DRDY

DISPB_D3_VSYNC

Even Field

Odd Field

Line and Field Timing - PAL

Figure 50. TV Encoder Interface Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

60

Freescale Semiconductor

Electrical Characteristics

4.3.15.4.2 Interface to a TV Encoder, Electrical Characteristics

The timing characteristics of the TV encoder interface are identical to the synchronous display

characteristics. See Section 4.3.15.2.2, “Interface to Active Matrix TFT LCD Panels, Electrical

Characteristics” on page 55.

4.3.15.5 Asynchronous Interfaces

4.3.15.5.1 Parallel Interfaces, Functional Description

The IPU supports the following asynchronous parallel interfaces:

•

System 80 interface

— Type 1 (sampling with the chip select signal) with and without byte enable signals.

— Type 2 (sampling with the read and write signals) with and without byte enable signals.

System 68k interface

•

— Type 1 (sampling with the chip select signal) with or without byte enable signals.

— Type 2 (sampling with the read and write signals) with or without byte enable signals.

For each of four system interfaces, there are three burst modes:

1. Burst mode without a separate clock. The burst length is defined by the corresponding parameters

of the IDMAC (when data is transferred from the system memory) of by the HBURST signal

(when the MCU directly accesses the display via the slave AHB bus). For system 80 and system

68k type 1 interfaces, data is sampled by the CS signal and other control signals changes only when

transfer direction is changed during the burst. For type 2 interfaces, data is sampled by the WR/RD

signals (system 80) or by the ENABLE signal (system 68k) and the CS signal stays active during

the whole burst.

2. Burst mode with the separate clock DISPB_BCLK. In this mode, data is sampled with the

DISPB_BCLK clock. The CS signal stays active during whole burst transfer. Other controls are

changed simultaneously with data when the bus state (read, write or wait) is altered. The CS

signals and other controls move to non-active state after burst has been completed.

3. Single access mode. In this mode, slave AHB and DMA burst are broken to single accesses. The

data is sampled with CS or other controls according the interface type as described above. All

controls (including CS) become non-active for one display interface clock after each access. This

mode corresponds to the ATI single access mode.

Both system 80 and system 68k interfaces are supported for all described modes as depicted in Figure 51,

Figure 52, Figure 53, and Figure 54. These timing images correspond to active-low DISPB_D#_CS,

DISPB_D#_WR and DISPB_D#_RD signals.

Additionally, the IPU allows a programmable pause between two burst. The pause is defined in the

HSP_CLK cycles. It allows to avoid timing violation between two sequential bursts or two accesses to

different displays. The range of this pause is from 4 to 19 HSP_CLK cycles.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

61

Electrical Characteristics

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Burst access mode with sampling by CS signal

DISPB_BCLK

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Burst access mode with sampling by separate burst clock (BCLK)

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Single access mode (all control signals are not active for one display interface clock after each display access)

Figure 51. Asynchronous Parallel System 80 Interface (Type 1) Burst Mode Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

62

Freescale Semiconductor

Electrical Characteristics

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Burst access mode with sampling by WR/RD signals

DISPB_BCLK

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Burst access mode with sampling by separate burst clock (BCLK)

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

DISPB_RD

DISPB_DATA

Single access mode (all control signals are not active for one display interface clock after each display access)

Figure 52. Asynchronous Parallel System 80 Interface (Type 2) Burst Mode Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

63

Electrical Characteristics

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Burst access mode with sampling by CS signal

DISPB_BCLK

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Burst access mode with sampling by separate burst clock (BCLK)

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Single access mode (all control signals are not active for one display interface clock after each display access)

Figure 53. Asynchronous Parallel System 68k Interface (Type 1) Burst Mode Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

64

Freescale Semiconductor

Electrical Characteristics

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Burst access mode with sampling by ENABLE signal

DISPB_BCLK

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Burst access mode with sampling by separate burst clock (BCLK)

DISPB_D#_CS

DISPB_PAR_RS

DISPB_WR

(READ/WRITE)

DISPB_RD

(ENABLE)

DISPB_DATA

Single access mode (all control signals are not active for one display interface clock after each display access)

Figure 54. Asynchronous Parallel System 68k Interface (Type 2) Burst Mode TIming Diagram

Display read operation can be performed with wait states when each read access takes up to 4 display

interface clock cycles according to the DISP0_RD_WAIT_ST parameter in the

DI_DISP0_TIME_CONF_3, DI_DISP1_TIME_CONF_3, DI_DISP2_TIME_CONF_3 Registers.

Figure 55 shows timing of the parallel interface with read wait states.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

65

Electrical Characteristics

WRITE OPERATION

DISP0_RD_WAIT_ST=00

READ OPERATION

DISPB_D#_CS

DISPB_RD

DISPB_WR

DISPB_PAR_RS

DISPB_DATA

DISP0_RD_WAIT_ST=01

DISPB_D#_CS

DISPB_RD

DISPB_WR

DISPB_PAR_RS

DISPB_DATA

DISP0_RD_WAIT_ST=10

DISPB_D#_CS

DISPB_RD

DISPB_WR

DISPB_PAR_RS

DISPB_DATA

Figure 55. Parallel Interface Timing Diagram—Read Wait States

4.3.15.5.2 Parallel Interfaces, Electrical Characteristics

Figure 56, Figure 58, Figure 57, and Figure 59 depict timing of asynchronous parallel interfaces based on

the system 80 and system 68k interfaces. Table 47 lists the timing parameters at display access level. All

timing images are based on active low control signals (signals polarity is controlled via the

DI_DISP_SIG_POL Register).

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

66

Freescale Semiconductor

Electrical Characteristics

IP28, IP27

DISPB_PAR_RS

DISPB_RD (READ_L)

DISPB_DATA[17]

(READ_H)

IP35, IP33

IP36, IP34

DISPB_D#_CS

DISPB_WR (WRITE_L)

DISPB_DATA[16]

(WRITE_H)

IP31, IP29

IP32, IP30

read point

IP38

IP37

DISPB_DATA

(Input)

Read Data

IP40

IP39

DISPB_DATA

(Output)

IP46,IP44

IP47

IP45, IP43

IP42, IP41

Figure 56. Asynchronous Parallel System 80 Interface (Type 1) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

67

Electrical Characteristics

IP28, IP27

DISPB_PAR_RS

DISPB_D#_CS

IP35, IP33

IP36, IP34

DISPB_RD (READ_L)

DISPB_DATA[17]

(READ_H)

DISPB_WR (WRITE_L)

DISPB_DATA[16]

(WRITE_H)

IP31, IP29

IP32, IP30

read point

IP38

IP37

DISPB_DATA

(Input)

Read Data

IP39

IP40

DISPB_DATA

(Output)

IP46,IP44

IP47

IP45, IP43

IP42, IP41

Figure 57. Asynchronous Parallel System 80 Interface (Type 2) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

68

Freescale Semiconductor

Electrical Characteristics

IP28, IP27

DISPB_PAR_RS

DISPB_RD (ENABLE_L)

DISPB_DATA[17]

(ENABLE_H)

IP35,IP33

IP36, IP34

DISPB_D#_CS

DISPB_WR

(READ/WRITE)

IP31, IP29

IP32, IP30

read point

IP38

IP37

DISPB_DATA

(Input)

Read Data

IP39

IP40

DISPB_DATA

(Output)

IP46,IP44

IP47

IP45, IP43

IP42, IP41

Figure 58. Asynchronous Parallel System 68k Interface (Type 1) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

69

Electrical Characteristics

IP28, IP27

DISPB_PAR_RS

DISPB_D#_CS

IP35,IP33

IP36, IP34

DISPB_RD (ENABLE_L)

DISPB_DATA[17]

(ENABLE_H)

DISPB_WR

(READ/WRITE)

IP32, IP30

IP31, IP29

read point

IP38

IP37

DISPB_DATA

(Input)

Read Data

IP39

IP40

DISPB_DATA

(Output)

IP46,IP44

IP47

IP45, IP43

IP42, IP41

Figure 59. Asynchronous Parallel System 68k Interface (Type 2) Timing Diagram

Table 47. Asynchronous Parallel Interface Timing Parameters—Access Level

1

ID

Parameter

Symbol

Min.

Typ.

Max.

Tdicpr+1.5

Units

2

IP27 Read system cycle time

IP28 Write system cycle time

IP29 Read low pulse width

IP30 Read high pulse width

Tcycr Tdicpr–1.5

Tdicpr

ns

3

Tcycw Tdicpw–1.5

Tdicpw

Tdicpw+1.5

4

5

Trl

Tdicdr–Tdicur–1.5

Tdicdr –Tdicur

Tdicdr–Tdicur+1.5

Tdicpr–Tdicdr+Tdicur+1.5

Trh

Tdicpr–Tdicdr+Tdicur–1.5 Tdicpr–Tdicdr+

Tdicur

6

7

IP31 Write low pulse width

IP32 Write high pulse width

Twl

Tdicdw–Tdicuw–1.5

Tdicdw –Tdicuw

Tdicdw–Tdicuw+1.5

ns

Twh

Tdicpw–Tdicdw+

Tdicuw–1.5

Tdicpw–Tdicdw+

Tdicuw

Tdicpw–Tdicdw+

Tdicuw+1.5

IP33 Controls setup time for read

IP34 Controls hold time for read

Tdcsr Tdicur–1.5

Tdicur

—

ns

Tdchr Tdicpr–Tdicdr–1.5

Tdicpr–Tdicdr

Tdicuw

IP35 Controls setup time for write Tdcsw Tdicuw–1.5

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

70

Freescale Semiconductor

Electrical Characteristics

Table 47. Asynchronous Parallel Interface Timing Parameters—Access Level (continued)

1

ID

Parameter

Symbol

Min.

Typ.

Max.

Units

IP36 Controls hold time for write

Tdchw Tdicpw–Tdicdw–1.5

Tdicpw–Tdicdw

—

ns

8

9

10

IP37 Slave device data delay

Tracc

Troh

Tds

0

Tdrp –Tlbd –Tdicur–1.5

Tdicpr–Tdicdr–1.5

—

8

IP38 Slave device data hold time

IP39 Write data setup time

IP40 Write data hold time

Tdrp–Tlbd–Tdicdr+1.5

Tdicdw–1.5

—

Tdicdw

Tdicpw–Tdicdw

Tdicpr

Tdh

Tdicpw–Tdicdw–1.5

—

2

IP41 Read period

Tdicpr Tdicpr–1.5

Tdicpw Tdicpw–1.5

Tdicdr Tdicdr–1.5

Tdicur Tdicur–1.5

Tdicdw Tdicdw–1.5

Tdicuw Tdicuw–1.5

Tdrp Tdrp–1.5

Tdicpr+1.5

Tdicpw+1.5

Tdicdr+1.5

Tdicur+1.5

Tdicdw+1.5

Tdicuw+1.5

Tdrp+1.5

3

IP42 Write period

Tdicpw

Tdicdr

4

IP43 Read down time

5

IP44 Read up time

Tdicur

6

IP45 Write down time

Tdicdw

Tdicuw

Tdrp

7

IP46 Write up time

9

IP47 Read time point

1

The exact conditions have not been finalized, but will likely match the current customer requirement for their specific display. These

conditions may be device specific.

2

Display interface clock period value for read:

DISP#_IF_CLK_PER_RD

HSP_CLK_PERIOD

----------------------------------------------------------------

⋅ ceil

Tdicpr = T

HSP_CLK

3

Display interface clock period value for write:

DISP#_IF_CLK_PER_WR

HSP_CLK_PERIOD

-----------------------------------------------------------------

⋅ ceil

Tdicpw = T

HSP_CLK

4

Display interface clock down time for read:

1

2

2 ⋅ DISP#_IF_CLK_DOWN_RD

--

-------------------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicdr =

T

HSP_CLK_PERIOD

5

6

7

Display interface clock up time for read:

1

2

2 ⋅ DISP#_IF_CLK_UP_RD

--

--------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicur =

T

HSP_CLK_PERIOD

Display interface clock down time for write:

1

2

2 ⋅ DISP#_IF_CLK_DOWN_WR

--

--------------------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicdw =

T

HSP_CLK_PERIOD

Display interface clock up time for write:

1

2

2 ⋅ DISP#_IF_CLK_UP_WR

--

---------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicuw =

T

HSP_CLK_PERIOD

8

9

This parameter is a requirement to the display connected to the IPU

Data read point

DISP#_READ_EN

HSP_CLK_PERIOD

--------------------------------------------------

⋅ ceil

Tdrp = T

HSP_CLK

10

Loopback delay Tlbd is the cumulative propagation delay of read controls and read data. It includes an IPU output delay, a

device-level output delay, board delays, a device-level input delay, an IPU input delay. This value is device specific.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

71

Electrical Characteristics

The DISP#_IF_CLK_PER_WR, DISP#_IF_CLK_PER_RD, HSP_CLK_PERIOD,

DISP#_IF_CLK_DOWN_WR, DISP#_IF_CLK_UP_WR, DISP#_IF_CLK_DOWN_RD,

DISP#_IF_CLK_UP_RD and DISP#_READ_EN parameters are programmed via the

DI_DISP#_TIME_CONF_1, DI_DISP#_TIME_CONF_2 and DI_HSP_CLK_PER Registers.

4.3.15.5.3 Serial Interfaces, Functional Description

The IPU supports the following types of asynchronous serial interfaces:

•

3-wire (with bidirectional data line)

4-wire (with separate data input and output lines)

5-wire type 1 (with sampling RS by the serial clock)

5-wire type 2 (with sampling RS by the chip select signal)

Figure 60 depicts timing of the 3-wire serial interface. The timing images correspond to active-low

DISPB_D#_CS signal and the straight polarity of the DISPB_SD_D_CLK signal.

For this interface, a bidirectional data line is used outside the device. The IPU still uses separate input and

output data lines (IPP_IND_DISPB_SD_D and IPP_DO_DISPB_SD_D). The I/O mux should provide

joining the internal data lines to the bidirectional external line according to the IPP_OBE_DISPB_SD_D

signal provided by the IPU.

Each data transfer can be preceded by an optional preamble with programmable length and contents. The

preamble is followed by read/write (RW) and address (RS) bits. The order of the these bits is

programmable. The RW bit can be disabled. The following data can consist of one word or of a whole

burst. The interface parameters are controlled by the DI_SER_DISP1_CONF and DI_SER_DISP2_CONF

Registers.

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

RW

RS

D7

D6

D5

D4

D3

D2

D1

D0

Input or output data

Preamble

Figure 60. 3-Wire Serial Interface Timing Diagram

Figure 61 depicts timing of the 4-wire serial interface. For this interface, there are separate input and output

data lines both inside and outside the device.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

72

Freescale Semiconductor

Electrical Characteristics

Write

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

RS

D7

D6

D5

D4

D3

D2

D1

D0

Preamble

Output data

DISPB_SD_D

(Input)

Read

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

RS

Preamble

DISPB_SD_D

(Input)

D7

D6

D5

D4

D3

D2

D1

D0

Input data

Figure 61. 4-Wire Serial Interface Timing Diagram

Figure 62 depicts timing of the 5-wire serial interface (Type 1). For this interface, a separate RS line is

added. When a burst is transmitted within single active chip select interval, the RS can be changed at

boundaries of words.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

73

Electrical Characteristics

Write

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

D7

D6

D5

D4

D3

D2

D1

D0

Preamble

Output data

DISPB_SD_D

(Input)

DISPB_SER_RS

Read

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

Preamble

DISPB_SD_D

(Input)

D7

D6

D5

D4

D3

D2

D1

D0

Input data

DISPB_SER_RS

Figure 62. 5-Wire Serial Interface (Type 1) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

74

Freescale Semiconductor

Electrical Characteristics

Figure 63 depicts timing of the 5-wire serial interface (Type 2). For this interface, a separate RS line is

added. When a burst is transmitted within single active chip select interval, the RS can be changed at

boundaries of words.

Write

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

D7

D6

D5

D4

D3

D2

D1

D0

Output data

Preamble

DISPB_SD_D

(Input)

1 display IF

clock cycle

DISPB_SER_RS

Read

1 display IF

clock cycle

1 display IF

clock cycle

DISPB_D#_CS

DISPB_SD_D_CLK

DISPB_SD_D

(Output)

RW

Preamble

DISPB_SD_D

(Input)

D7

D6

D5

D4

D3

D2

D1

D0

Input data

1 display IF

clock cycle

DISPB_SER_RS

Figure 63. 5-Wire Serial Interface (Type 2) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

75

Electrical Characteristics

4.3.15.5.4 Serial Interfaces, Electrical Characteristics

Figure 64 depicts timing of the serial interface. Table 48 lists the timing parameters at display access level.

IP49, IP48

DISPB_SER_RS

IP56,IP54

IP57, IP55

DISPB_SD_D_CLK

IP51, IP53

IP50, IP52

read point

IP59

IP58

DISPB_DATA

(Input)

Read Data

IP60

IP61

DISPB_DATA

(Output)

IP67,IP65

IP47

IP64, IP66

IP62, IP63

Figure 64. Asynchronous Serial Interface Timing Diagram

Table 48. Asynchronous Serial Interface Timing Parameters—Access Level

1

ID

Parameter

Symbol

Min.

Typ.

Max.

Tdicpr+1.5

Units

2

IP48 Read system cycle time

IP49 Write system cycle time

IP50 Read clock low pulse width

IP51 Read clock high pulse width

Tcycr Tdicpr–1.5

Tdicpr

ns

3

Tcycw Tdicpw–1.5

Tdicpw

Tdicpw+1.5

4

5

Trl

Tdicdr–Tdicur–1.5

Tdicdr –Tdicur

Tdicdr–Tdicur+1.5

Tdicpr–Tdicdr+Tdicur+1.5

Trh

Tdicpr–Tdicdr+Tdicur–1.5 Tdicpr–Tdicdr+

Tdicur

6

7

IP52 Write clock low pulse width

IP53 Write clock high pulse width

Twl

Tdicdw–Tdicuw–1.5

Tdicdw –Tdicuw

Tdicdw–Tdicuw+1.5

ns

Twh

Tdicpw–Tdicdw+

Tdicuw–1.5

Tdicpw–Tdicdw+ Tdicpw–Tdicdw+

Tdicuw

Tdicuw+1.5

IP54 Controls setup time for read

IP55 Controls hold time for read

Tdcsr Tdicur–1.5

Tdicur

—

ns

Tdchr Tdicpr–Tdicdr–1.5

Tdicpr–Tdicdr

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

76

Freescale Semiconductor

Electrical Characteristics

Table 48. Asynchronous Serial Interface Timing Parameters—Access Level (continued)

1

ID

Parameter

Symbol

Min.

Typ.

Tdicuw

Max.

Units

IP56 Controls setup time for write Tdcsw Tdicuw–1.5

—

ns

IP57 Controls hold time for write

Tdchw Tdicpw–Tdicdw–1.5

Tdicpw–Tdicdw

—

10

8

9

IP58 Slave device data delay

Tracc

Troh

Tds

0

Tdrp –Tlbd –Tdicur–1.5

Tdicpr–Tdicdr–1.5

—

8

IP59 Slave device data hold time

IP60 Write data setup time

IP61 Write data hold time

Tdrp–Tlbd–Tdicdr+1.5

Tdicdw–1.5

—

Tdicdw

Tdicpw–Tdicdw

Tdicpr

Tdh

Tdicpw–Tdicdw–1.5

—

2

IP62 Read period

Tdicpr Tdicpr–1.5

Tdicpw Tdicpw–1.5

Tdicdr Tdicdr–1.5

Tdicur Tdicur–1.5

Tdicdw Tdicdw–1.5

Tdicuw Tdicuw–1.5

Tdrp Tdrp–1.5

Tdicpr+1.5

Tdicpw+1.5

Tdicdr+1.5

Tdicur+1.5

Tdicdw+1.5

Tdicuw+1.5

Tdrp+1.5

3

IP63 Write period

Tdicpw

Tdicdr

4

IP64 Read down time

5

IP65 Read up time

Tdicur

6

IP66 Write down time

Tdicdw

Tdicuw

Tdrp

7

IP67 Write up time

9

IP68 Read time point

1

2

The exact conditions have not been finalized, but will likely match the current customer requirement for their specific display. These

conditions may be device specific.

Display interface clock period value for read:

DISP#_IF_CLK_PER_RD

HSP_CLK_PERIOD

----------------------------------------------------------------

⋅ ceil

Tdicpr = T

HSP_CLK

3

4

5

6

7

Display interface clock period value for write:

DISP#_IF_CLK_PER_WR

HSP_CLK_PERIOD

-----------------------------------------------------------------

⋅ ceil

Tdicpw = T

HSP_CLK

Display interface clock down time for read:

1

2

2 ⋅ DISP#_IF_CLK_DOWN_RD

--

-------------------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicdr =

T

HSP_CLK_PERIOD

Display interface clock up time for read:

1

2

2 ⋅ DISP#_IF_CLK_UP_RD

--

--------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicur =

T

HSP_CLK_PERIOD

Display interface clock down time for write:

1

2

2 ⋅ DISP#_IF_CLK_DOWN_WR

--

--------------------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicdw =

T

HSP_CLK_PERIOD

Display interface clock up time for write:

1

2

2 ⋅ DISP#_IF_CLK_UP_WR

--

---------------------------------------------------------------------

⋅ ceil

HSP_CLK

Tdicuw =

T

HSP_CLK_PERIOD

8

9

This parameter is a requirement to the display connected to the IPU.

Data read point:

DISP#_READ_EN

HSP_CLK_PERIOD

--------------------------------------------------

⋅ ceil

Tdrp = T

HSP_CLK

10

Loopback delay Tlbd is the cumulative propagation delay of read controls and read data. It includes an IPU output delay, a

device-level output delay, board delays, a device-level input delay, an IPU input delay. This value is device specific.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

77

Electrical Characteristics

The DISP#_IF_CLK_PER_WR, DISP#_IF_CLK_PER_RD, HSP_CLK_PERIOD,

DISP#_IF_CLK_DOWN_WR, DISP#_IF_CLK_UP_WR, DISP#_IF_CLK_DOWN_RD,

DISP#_IF_CLK_UP_RD and DISP#_READ_EN parameters are programmed via the

DI_DISP#_TIME_CONF_1, DI_DISP#_TIME_CONF_2 and DI_HSP_CLK_PER Registers.

4.3.16 Memory Stick Host Controller (MSHC)

Figure 65, Figure 66, and Figure 67 depict the MSHC timings, and Table 49 and Table 50 list the timing

parameters.

tSCLKc

tSCLKwh

tSCLKwl

MSHC_SCLK

tSCLKr

tSCLKf

Figure 65. MSHC_CLK Timing Diagram

tSCLKc

MSHC_SCLK

tBSsu

tBSh

MSHC_BS

tDsu

tDh

MSHC_DATA

(Output)

tDd

MSHC_DATA

(Intput)

Figure 66. Transfer Operation Timing Diagram (Serial)

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

78

Freescale Semiconductor

Electrical Characteristics

tSCLKc

MSHC_SCLK

MSHC_BS

tBSsu

tBSh

tDsu

tDh

MSHC_DATA

(Output)

tDd

MSHC_DATA

(Intput)

Figure 67. Transfer Operation Timing Diagram (Parallel)

NOTE

The Memory Stick Host Controller is designed to meet the timing

requirements per Sony's Memory Stick Pro Format Specifications

document. Tables in this section details the specifications requirements for

parallel and serial modes, and not the MCIMX31C timing.

1

Table 49. Serial Interface Timing Parameters

Standards

Signal

Parameter

Symbol

Unit

Min.

Max.

Cycle

H pulse length

L pulse length

Rise time

tSCLKc

tSCLKwh

tSCLKwl

tSCLKr

tSCLKf

tBSsu

tBSh

50

15

—

5

—

10

—

15

ns

MSHC_SCLK

Fall time

Setup time

Hold time

MSHC_BS

5

Setup time

Hold time

tDsu

5

MSHC_DATA

tDh

5

Output delay time

tDd

—

1

Timing is guaranteed for NVCC from 2.7 through 3.1 V. See NVCC restrictions described in Table 7, "Operating

Ranges," on page 12.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

79

Electrical Characteristics

1

Table 50. Parallel Interface Timing Parameters

Standards

Signal

Parameter

Symbol

Unit

Min

Max

Cycle

H pulse length

L pulse length

Rise time

tSCLKc

tSCLKwh

tSCLKwl

tSCLKr

tSCLKf

tBSsu

tBSh

25

5

—

10

—

15

ns

MSHC_SCLK

MSHC_BS

5

—

8

Fall time

Setup time

Hold time

1

Setup time

Hold time

tDsu

8

MSHC_DATA

tDh

1

Output delay time

tDd

—

1

Timing is guaranteed for NVCC from 2.7 through 3.1 V. See NVCC restrictions described in Table 7, "Operating Ranges," on

page 12.

4.3.17 Personal Computer Memory Card International Association

(PCMCIA)

Figure 68 and Figure 69 depict the timings pertaining to the PCMCIA module, each of which is an

example of one clock of strobe set-up time and one clock of strobe hold time. Table 51 lists the timing

parameters.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

80

Freescale Semiconductor

Electrical Characteristics

HCLK

HADDR

ADDR 1

CONTROL 1

CONTROL

HWDATA

HREADY

HRESP

DATA write 1

OKAY

ADDR 1

A[25:0]

DATA write 1

D[15:0]

WAIT

REG

OE/WE/IORD/IOWR

CE1/CE2

RW

POE

PSHT

PSST

PSL

Figure 68. Write Accesses Timing Diagram—PSHT=1, PSST=1

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

81

Electrical Characteristics

HCLK

HADDR

ADDR 1

CONTROL 1

CONTROL

RWDATA

HREADY

HRESP

DATA read 1

OKAY

ADDR 1

A[25:0]

D[15:0]

WAIT

REG

OE/WE/IORD/IOWR

CE1/CE2

RW

POE

PSST

PSHT

PSL

Figure 69. Read Accesses Timing Diagram—PSHT=1, PSST=1

Table 51. PCMCIA Write and Read Timing Parameters

Symbol

Parameter

Min

Max

Unit

PSHT

PSST

PSL

PCMCIA strobe hold time

0

1

63

clock

PCMCIA strobe set up time

PCMCIA strobe length

128

4.3.18 PWM Electrical Specifications

This section describes the electrical information of the PWM. The PWM can be programmed to select one

of three clock signals as its source frequency. The selected clock signal is passed through a prescaler before

being input to the counter. The output is available at the pulse-width modulator output (PWMO) external

pin.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

82

Freescale Semiconductor

Electrical Characteristics

4.3.18.1 PWM Timing

Figure 70 depicts the timing of the PWM, and Table 52 lists the PWM timing characteristics.

1

2a

3b

System Clock

2b

4b

3a

4a

PWM Output

Figure 70. PWM Timing

Table 52. PWM Output Timing Parameters

ID

Parameter

Min

Max

Unit

1

System CLK frequency

Clock high time

Clock low time

0

12.29

9.91

—

ipg_clk

—

MHz

ns

2a

2b

3a

3b

4a

4b

—

ns

Clock fall time

0.5

ns

Clock rise time

—

0.5

ns

Output delay time

Output setup time

—

9.37

—

ns

8.71

ns

1

CL of PWMO = 30 pF

4.3.19 SDHC Electrical Specifications

This section describes the electrical information of the SDHC.

4.3.19.1 SDHC Timing

Figure 71 depicts the timings of the SDHC, and Table 53 lists the timing parameters.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

83

Electrical Characteristics

SD4

SD3

SD2

SD1

CLK

SD5

SD6

CMD

Output from SDHC to card

Input to SDHC

DATA[3:0]

SD7

CMD

DATA[3:0]

SD8

Figure 71. SDHC Timing Diagram

.

Table 53. SDHC Interface Timing Parameters

ID

Card Input Clock

Parameter

Symbol

Min

Max

Unit

1

SD1

Clock Frequency (Low Speed)

Clock Frequency (SD/SDIO Full Speed)

Clock Frequency (MMC Full Speed)

Clock Frequency (Identification Mode)

Clock Low Time

f

0

400

25

20

400

—

kHz

MHz

kHz

ns

PP

2

3

4

0

f

100

10

—

OD

SD2

SD3

SD4

SD5

t

WL

Clock High Time

t

—

ns

WH

Clock Rise Time

t

10

ns

TLH

THL

Clock Fall Time

t

ns

SDHC output / Card inputs CMD, DAT (Reference to CLK)

SD6 SDHC output delay

SDHC input / Card outputs CMD, DAT (Reference to CLK)

t

–6.5

3

ns

ODL

SD7

SD8

SDHC input setup

SDHC input hold

t

—

18.5

ns

IS

t

–11.5

IH

1

2

3

4

In low speed mode, card clock must be lower than 400 kHz, voltage ranges from 2.7 V–3.3 V.

In normal data transfer mode for SD/SDIO card, clock frequency can be any value between 0 MHz–25 MHz.

In normal data transfer mode for MMC card, clock frequency can be any value between 0 MHz–20 MHz.

In card identification mode, card clock must be 100 kHz–400 kHz, voltage ranges from 2.7 V–3.3 V.

4.3.20 SIM Electrical Specifications

Each SIM card interface consist of a total of 12 pins (for 2 separate ports of 6 pins each. Mostly one port

with 5 pins is used).

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

84

Freescale Semiconductor

Electrical Characteristics

The interface is meant to be used with synchronous SIM cards. This means that the SIM module provides

a clock for the SIM card to use. The frequency of this clock is normally 372 times the data rate on the

TX/RX pins, however SIM module can work with CLK equal to 16 times the data rate on TX/RX pins.

There is no timing relationship between the clock and the data. The clock that the SIM module provides

to the aim card will be used by the SIM card to recover the clock from the data much like a standard UART.

All six (or 5 in case bi directional TXRX is used) of the pins for each half of the SIM module are

asynchronous to each other.

There are no required timing relationships between the signals in normal mode, but there are some in two

specific cases: reset and power down sequences.

4.3.20.1 General Timing Requirements

Figure 72 shows the timing of the SIM module, and Figure 54 lists the timing parameters.

1/Sfreq

CLK

Sfall

Srise

Figure 72. SIM Clock Timing Diagram

Table 54. SIM Timing Specification—High Drive Strength

Num

Description

Symbol

Min

Max

Unit

1

SIM Clock Frequency (CLK)

S

0.01

5 (Some new cards

may reach 10)

MHz

freq

2

3

4

SIM CLK Rise Time

S

—

20

25

ns

rise

3

SIM CLK Fall Time

S

fall

SIM Input Transition Time (RX, SIMPD)

S

trans

1

2

3

50% duty cycle clock

With C = 50pF

4.3.20.2 Reset Sequence

4.3.20.2.1 Cards with Internal Reset

The sequence of reset for this kind of SIM Cards is as follows (see Figure 73):

•

After powerup, the clock signal is enabled on SGCLK (time T0)

After 200 clock cycles, RX must be high.

The card must send a response on RX acknowledging the reset between 400 and 40000 clock

cycles after T0.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

85

Electrical Characteristics

SVEN

CLK

response

RX

1

2

< 200 clock cycles

1

2

T0

400 clock cycles <

< 40000 clock cycles

Figure 73. Internal-Reset Card Reset Sequence

4.3.20.2.2 Cards with Active Low Reset

The sequence of reset for this kind of card is as follows (see Figure 74):

1. After powerup, the clock signal is enabled on CLK (time T0)

2. After 200 clock cycles, RX must be high.

3. RST must remain Low for at least 40000 clock cycles after T0 (no response is to be received on

RX during those 40000 clock cycles)

4. RST is set High (time T1)

5. RST must remain High for at least 40000 clock cycles after T1 and a response must be received

on RX between 400 and 40000 clock cycles after T1.

SVEN

RST

CLK

response

RX

2

1

3

T0

T1

< 200 clock cycles

1

2

3

400 clock cycles <

< 40000 clock cycles

400000 clock cycles <

Figure 74. Active-Low-Reset Card Reset Sequence

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

86

Freescale Semiconductor

Electrical Characteristics

4.3.20.3 Power Down Sequence

Power down sequence for SIM interface is as follows:

1. SIMPD port detects the removal of the SIM Card

2. RST goes Low

3. CLK goes Low

4. TX goes Low

5. VEN goes Low

Each of this steps is done in one CKIL period (usually 32 kHz). Power down can be started because of a

SIM Card removal detection or launched by the processor. Figure 75 and Table 55 show the usual timing

requirements for this sequence, with Fckil = CKIL frequency value.

Spd2rst

SIMPD

RST

Srst2clk

CLK

Srst2dat

DATA_TX

Srst2ven

SVEN

Figure 75. SmartCard Interface Power Down AC Timing

Table 55. Timing Requirements for Power Down Sequence

Num

Description

Symbol

Min

Max

Unit

1

2

3

4

SIM reset to SIM clock stop

S

0.9*1/FCKIL

1.8*1/FCKIL

2.7*1/FCKIL

0.9*1/FCKIL

0.8

1.2

1.8

25

µs

ns

rst2clk

rst2dat

rst2ven

SIM reset to SIM TX data low

S

SIM reset to SIM Voltage Enable Low

SIM Presence Detect to SIM reset Low

S

pd2rst

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

87

Electrical Characteristics

4.3.21 SJC Electrical Specifications

This section details the electrical characteristics for the SJC module. Figure 76 depicts the SJC test clock

input timing. Figure 77 depicts the SJC boundary scan timing, Figure 78 depicts the SJC test access port,

Figure 79 depicts the SJC TRST timing, and Table 56 lists the SJC timing parameters.

SJ1

SJ2

VM

SJ2

VM

TCK

(Input)

VIH

VIL

SJ3

Figure 76. Test Clock Input Timing Diagram

TCK

(Input)

VIH

VIL

SJ5

SJ4

Input Data Valid

Data

Inputs

SJ6

Data

Outputs

Output Data Valid

SJ7

SJ6

Data

Outputs

Data

Outputs

Output Data Valid

Figure 77. Boundary Scan (JTAG) Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

88

Freescale Semiconductor

Electrical Characteristics

TCK

(Input)

VIH

VIL

SJ8

SJ9

TDI

TMS

Input Data Valid

(Input)

SJ10

SJ11

SJ10

TDO

(Output)

Output Data Valid

TDO

(Output)

TDO

(Output)

Output Data Valid

Figure 78. Test Access Port Timing Diagram

TCK

(Input)

SJ13

TRST

(Input)

SJ12

Figure 79. TRST Timing Diagram

Table 56. SJC Timing Parameters

All Frequencies

ID

Parameter

Unit

Min

Max

1

SJ1 TCK cycle time

100

40

—

3

ns

2

SJ2 TCK clock pulse width measured at V_M

SJ3 TCK rise and fall times

SJ4 Boundary scan input data set-up time

SJ5 Boundary scan input data hold time

SJ6 TCK low to output data valid

SJ7 TCK low to output high impedance

SJ8 TMS, TDI data set-up time

10

50

—

50

—

44

—

10

50

—

SJ9 TMS, TDI data hold time

SJ10 TCK low to TDO data valid

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

89

Electrical Characteristics

Table 56. SJC Timing Parameters (continued)

Parameter

All Frequencies

Min Max

44

ID

Unit

SJ11 TCK low to TDO high impedance

SJ12 TRST assert time

—

ns

100

40

—

SJ13 TRST set-up time to TCK low

1

2

On cases where SDMA TAP is put in the chain, the max TCK frequency is limited by max ratio of 1:8 of SDMA core frequency

to TCK limitation. This implies max frequency of 8.25 MHz (or 121.2 ns) for 66 MHz IPG clock.

V_{M -}mid point voltage

4.3.22 SSI Electrical Specifications

This section describes the electrical information of SSI. Note the following pertaining to timing

information:

•

All the timings for the SSI are given for a non-inverted serial clock polarity (TSCKP/RSCKP = 0)

and a non-inverted frame sync (TFSI/RFSI = 0). If the polarity of the clock and/or the frame sync

have been inverted, all the timing remains valid by inverting the clock signal STCK/SRCK and/or

the frame sync STFS/SRFS shown in the tables and in the figures.

•

All timings are on AUDMUX signals when SSI is being used for data transfer.

“Tx” and “Rx” refer to the Transmit and Receive sections of the SSI.

For internal Frame Sync operation using external clock, the FS timing will be same as that of Tx

Data (for example, during AC97 mode of operation).

4.3.22.1 SSI Transmitter Timing with Internal Clock

Figure 80 depicts the SSI transmitter timing with internal clock, and Table 57 lists the timing parameters.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

90

Freescale Semiconductor

Electrical Characteristics

SS1

SS3

SS5

SS4

SS2

AD1_TXC

(Output)

SS8

SS6

AD1_TXFS (bl)

(Output)

SS10

SS12

AD1_TXFS (wl)

(Output)

SS14

SS17

SS15

SS16

SS18

AD1_TXD

(Output)

SS43

SS42

SS19

AD1_RXD

(Input)

Note: SRXD Input in Synchronous mode only

SS1

SS3

SS5

SS4

SS2

DAM1_T_CLK

(Output)

SS8

SS6

DAM1_T_FS (bl)

(Output)

SS10

SS12

DAM1_T_FS (wl)

(Output)

SS14

SS17

SS15

SS18

SS16

DAM1_TXD

(Output)

SS43

SS42

SS19

DAM1_RXD

(Input)

Note: SRXD Input in Synchronous mode only

Figure 80. SSI Transmitter with Internal Clock Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

91

Electrical Characteristics

Table 57. SSI Transmitter with Internal Clock Timing Parameters

ID

Parameter

Min

Max

Unit

Internal Clock Operation

SS1

SS2

(Tx/Rx) CK clock period

(Tx/Rx) CK clock high period

81.4

36.0

—

ns

SS3

(Tx/Rx) CK clock rise time

6

SS4

(Tx/Rx) CK clock low period

(Tx/Rx) CK clock fall time

36.0

—

SS5

6

SS6

(Tx) CK high to FS (bl) high

(Tx) CK high to FS (bl) low

—

15.0

6

SS8

—

SS10

SS12

SS14

SS15

SS16

SS17

SS18

SS19

(Tx) CK high to FS (wl) high

(Tx) CK high to FS (wl) low

(Tx/Rx) Internal FS rise time

(Tx/Rx) Internal FS fall time

(Tx) CK high to STXD valid from high impedance

(Tx) CK high to STXD high/low

(Tx) CK high to STXD high impedance

STXD rise/fall time

—

6

—

15.0

6

—

Synchronous Internal Clock Operation

SS42

SS43

SS52

SRXD setup before (Tx) CK falling

10.0

0

—

25

ns

pF

SRXD hold after (Tx) CK falling

Loading

—

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

92

Freescale Semiconductor

Electrical Characteristics

4.3.22.2 SSI Receiver Timing with Internal Clock

Figure 81 depicts the SSI receiver timing with internal clock, and Table 58 lists the timing parameters.

SS1

SS3

SS5

SS4

SS2

AD1_TXC

(Output)

SS9

SS7

AD1_TXFS (bl)

(Output)

SS11

SS13

AD1_TXFS (wl)

(Output)

SS20

SS21

AD1_RXD

(Input)

SS51

SS50

SS47

SS49

SS48

AD1_RXC

(Output)

SS1

SS3

SS5

SS4

SS2

DAM1_T_CLK

(Output)

SS9

SS7

DAM1_T_FS (bl)

(Output)

SS11

SS13

DAM1_T_FS (wl)

(Output)

SS20

SS21

DAM1_RXD

(Input)

SS47

SS51

SS50

SS49

SS48

DAM1_R_CLK

(Output)

Figure 81. SSI Receiver with Internal Clock Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

93

Electrical Characteristics

Table 58. SSI Receiver with Internal Clock Timing Parameters

ID

Internal Clock Operation

Parameter

Min

Max

Unit

SS1

SS2

SS3

SS4

SS5

SS7

SS9

(Tx/Rx) CK clock period

81.4

36.0

—

ns

(Tx/Rx) CK clock high period

(Tx/Rx) CK clock rise time

(Tx/Rx) CK clock low period

(Tx/Rx) CK clock fall time

(Rx) CK high to FS (bl) high

(Rx) CK high to FS (bl) low

6

36.0

—

6

—

15.0

—

SS11 (Rx) CK high to FS (wl) high

SS13 (Rx) CK high to FS (wl) low

SS20 SRXD setup time before (Rx) CK low

SS21 SRXD hold time after (Rx) CK low

Oversampling Clock Operation

—

10.0

0

—

SS47 Oversampling clock period

SS48 Oversampling clock high period

SS49 Oversampling clock rise time

SS50 Oversampling clock low period

SS51 Oversampling clock fall time

15.04

6

—

3

ns

—

6

—

3

—

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

94

Freescale Semiconductor

Electrical Characteristics

4.3.22.3 SSI Transmitter Timing with External Clock

Figure 82 depicts the SSI transmitter timing with external clock, and Table 59 lists the timing parameters.

SS22

SS23

SS25

SS26

SS24

AD1_TXC

(Input)

SS27

SS29

AD1_TXFS (bl)

(Input)

SS33

SS31

AD1_TXFS (wl)

(Input)

SS39

SS37

SS38

AD1_TXD

(Output)

SS45

SS44

AD1_RXD

(Input)

SS46

Note: SRXD Input in Synchronous mode only

SS22

SS26

SS25

SS24

SS23

DAM1_T_CLK

(Input)

SS29

SS27

DAM1_T_FS (bl)

(Input)

SS33

SS31

DAM1_T_FS (wl)

(Input)

SS39

SS37

SS38

DAM1_TXD

(Output)

SS45

SS44

DAM1_RXD

(Input)

SS46

Note: SRXD Input in Synchronous mode only

Figure 82. SSI Transmitter with External Clock Timing Diagram

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

95

Electrical Characteristics

Table 59. SSI Transmitter with External Clock Timing Parameters

ID

Parameter

Min

Max

Unit

External Clock Operation

SS22 (Tx/Rx) CK clock period

81.4

36.0

—

ns

SS23 (Tx/Rx) CK clock high period

SS24 (Tx/Rx) CK clock rise time

6.0

—

SS25 (Tx/Rx) CK clock low period

SS26 (Tx/Rx) CK clock fall time

36.0

—

6.0

15.0

—

SS27 (Tx) CK high to FS (bl) high

SS29 (Tx) CK high to FS (bl) low

SS31 (Tx) CK high to FS (wl) high

SS33 (Tx) CK high to FS (wl) low

SS37 (Tx) CK high to STXD valid from high impedance

SS38 (Tx) CK high to STXD high/low

SS39 (Tx) CK high to STXD high impedance

Synchronous External Clock Operation

SS44 SRXD setup before (Tx) CK falling

SS45 SRXD hold after (Tx) CK falling

SS46 SRXD rise/fall time

–10.0

10.0

–10.0

10.0

—

15.0

—

15.0

—

10.0

2.0

—

ns

6.0

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

96

Freescale Semiconductor

Electrical Characteristics

4.3.22.4 SSI Receiver Timing with External Clock

Figure 83 depicts the SSI receiver timing with external clock, and Table 60 lists the timing parameters.

SS22

SS26

SS25

SS24

SS23

AD1_TXC

(Input)

SS30

SS28

AD1_TXFS (bl)

(Input)

SS32

SS35

SS34

AD1_TXFS (wl)

(Input)

SS41

SS36

SS40

AD1_RXD

(Input)

SS22

SS24

SS26

SS25

SS23

DAM1_T_CLK

(Input)

SS30

SS28

DAM1_T_FS (bl)

(Input)

SS32

SS35

SS34

DAM1_T_FS (wl)

(Input)

SS41

SS36

SS40

DAM1_RXD

(Input)

Figure 83. SSI Receiver with External Clock Timing Diagram

Table 60. SSI Receiver with External Clock Timing Parameters

ID

Parameter

Min

Max

Unit

External Clock Operation

SS22 (Tx/Rx) CK clock period

SS23 (Tx/Rx) CK clock high period

SS24 (Tx/Rx) CK clock rise time

SS25 (Tx/Rx) CK clock low period

SS26 (Tx/Rx) CK clock fall time

81.4

36.0

—

ns

6.0

—

36.0

—

6.0

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

97

Electrical Characteristics

Table 60. SSI Receiver with External Clock Timing Parameters (continued)

ID

Parameter

Min

Max

Unit

SS28 (Rx) CK high to FS (bl) high

SS30 (Rx) CK high to FS (bl) low

SS32 (Rx) CK high to FS (wl) high

SS34 (Rx) CK high to FS (wl) low

SS35 (Tx/Rx) External FS rise time

SS36 (Tx/Rx) External FS fall time

SS40 SRXD setup time before (Rx) CK low

SS41 SRXD hold time after (Rx) CK low

–10.0

10.0

–10.0

10.0

—

15.0

—

ns

15.0

—

6.0

—

10.0

2.0

—

4.3.23 USB Electrical Specifications

This section describes the electrical information of the USBOTG port. The OTG port supports both serial

and parallel interfaces.

The high speed (HS) interface is supported via the ULPI (Ultra Low Pin Count Interface). Figure 84

depicts the USB ULPI timing diagram, and Table 61 lists the timing parameters.

Clock

T_SC

T_HC

Control out (stp)

T_SD

T_HD

Data out

T_DC

Control in (dir, nxt)

T_DD

Data in

Figure 84. USB ULPI Interface Timing Diagram

Table 61. USB ULPI Interface Timing Specification

1

Parameter

Symbol

Min

Max

Units

Setup time (control in, 8-bit data in)

Hold time (control in, 8-bit data in)

Output delay (control out, 8-bit data out)

TSC, TSD

THC, THD

TDC, TDD

6

0

—

9

ns

—

1

Timing parameters are given as viewed by transceiver side.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

98

Freescale Semiconductor

Package Information and Pinout

5 Package Information and Pinout

This section includes the contact assignment information and mechanical package drawing for the

MCIMX31C.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

99

Package Information and Pinout

5.1

MAPBGA Production Package 473 19 x 19 mm, 0.8 mm Pitch

This section contains the outline drawing, signal assignment map, and MAPBGA ground/power ID by ball

grid location for the 473 19 x 19 mm, 0.8 mm pitch package.

5.1.1

Production Package Outline Drawing–19 x 19 mm 0.8 mm

Figure 85. Production Package: Case 1931—0.8 mm Pitch

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

100

Freescale Semiconductor

Package Information and Pinout

5.1.3

Connection Tables–19 x 19 mm 0.8 mm

Table 62 shows the device connection list for power and ground, alpha-sorted followed by Table 63 on

page 103 which shows the no-connects. Table 64 on page 103 shows the device connection list for signals.

5.1.3.1

Ground and Power ID Locations—19 x 19 mm 0.8 mm

Table 62. 19 x 19 BGA Ground/Power ID by Ball Grid Location

GND/PWR ID

Ball Location

FGND

U16

FUSE_VDD T15

FVCC

GND

T16

A1, A2, A3, A21, A22, A23, B1, B2, B22, B23, C1, C2, C22, C23, D22, D23, J12, J13, K10, K11, K12, K13, K14,

L10, L11, L12, L13, L14, M9, M10, M11, M12, M13, M14, N10, N11, N12, N13, N14, P10, P11, P12, P13, P14,

R12, Y1, Y23, AA1, AA2, AA22, AA23, AB1, AB2, AB21, AB22, AB23, AC1, AC2, AC21, AC22, AC23

IOQVDD

MGND

MVCC

T8

U14

U15

NVCC1

NVCC2

NVCC3

NVCC4

NVCC5

NVCC6

NVCC7

NVCC8

NVCC9

NVCC10

NVCC21

NVCC22

QVCC

G15, G16, H16, J17

N16, P16, R15, R16, T14

K7, K8, L7, L8

H14, J15, K15

G9, G10, H8, H9

G11, G12, G13, H12

H15, J16, K16, L16, M16

H10, H11, J11

G14

P8, R7, R8, R9, T9

T11, T12, T13, U11

T10, U7, U8, U9, U10, V6, V7, V8, V9, V10

H13, J14, L15, M15, N9, N15, P9, P15, R10, R11, R13, R14

QVCC1

QVCC4

SGND

J8, J9, J10, K9

L9, M7, M8, N8

U13

U12

P18

P17

SVCC

UVCC

UGND

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

102

Freescale Semiconductor

Package Information and Pinout

1

Table 63. 19 x 19 BGA No Connects

Signal

Ball Location

NC

N7

P7

U21

1

These contacts are not used and must be floated by the user.

5.1.3.2

BGA Signal ID by Ball Grid Location—19 x 19 0.8 mm

Table 64. 19 x 19 BGA Signal ID by Ball Grid Location

Signal ID

Ball Location

Signal ID

Ball Location

A0

Y6

AC5

V15

AB3

AA3

Y3

CKIL

CLKO

E21

C20

H17

A20

N21

U17

Y22

Y18

Y19

Y20

AA21

K21

K22

K23

L20

L18

L21

J20

J21

L17

J22

J23

K20

H22

H20

H23

H21

N2

A1

A10

CLKSS

A11

COMPARE

CONTRAST

CS0

A12

A13

A14

Y15

Y14

V14

Y13

V13

Y12

AB5

V12

Y11

V11

Y10

Y9

CS1

A15

CS2

A16

CS3

A17

CS4

A18

A19

CS5

CSI_D10

CSI_D11

CSI_D12

CSI_D13

CSI_D14

CSI_D15

CSI_D4

A2

A20

A21

A22

A23

A24

A25

Y8

CSI_D5

A3

AA5

Y5

CSI_D6

A4

CSI_D7

A5

AC4

AB4

AA4

Y4

CSI_D8

A6

CSI_D9

A7

CSI_HSYNC

CSI_MCLK

CSI_PIXCLK

CSI_VSYNC

CSPI1_MISO

CSPI1_MOSI

CSPI1_SCLK

CSPI1_SPI_RDY

CSPI1_SS0

CSPI1_SS1

CSPI1_SS2

CSPI2_MISO

CSPI2_MOSI

A8

A9

AC3

E1

ATA_CS0

ATA_CS1

ATA_DIOR

ATA_DIOW

ATA_DMACK

ATA_RESET

BATT_LINE

BCLK

G4

E3

N1

H6

M4

E2

M1

F3

M2

F6

N6

W20

F17

C21

M3

BOOT_MODE0

BOOT_MODE1

B4

D5

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

103

Package Information and Pinout

Table 64. 19 x 19 BGA Signal ID by Ball Grid Location (continued)

Signal ID

Ball Location

Signal ID

Ball Location

BOOT_MODE2

BOOT_MODE3

BOOT_MODE4

CAPTURE

CAS

D20

F18

E20

D18

AA20

D12

F23

H7

CSPI2_SCLK

CSPI2_SPI_RDY

CSPI2_SS0

CSPI2_SS1

CSPI2_SS2

CSPI3_MISO

CSPI3_MOSI

GPIO1_3

GPIO1_4

GPIO1_5 (PWR RDY)

GPIO1_6

GPIO3_0

GPIO3_1

HSYNC

B5

D6

C5

A4

F7

CE_CONTROL

CKIH

D2

E4

CSPI3_SCLK

CSPI3_SPI_RDY

CTS1

G20

D21

D19

G18

G23

K17

L23

J18

F4

A9

CTS2

C12

U6

D0

D1

W4

V1

D10

D11

U4

I2C_CLK

I2C_DAT

D12

U3

K18

J7

D13

R6

IOIS16

D14

U2

KEY_COL0

KEY_COL1

KEY_COL2

KEY_COL3

KEY_COL4

KEY_COL5

KEY_COL6

KEY_COL7

KEY_ROW0

KEY_ROW1

KEY_ROW2

KEY_ROW3

KEY_ROW4

KEY_ROW5

KEY_ROW6

KEY_ROW7

L2PG

A15

B15

D14

C15

F13

A16

B16

A17

A13

B13

C13

A14

F12

D13

B14

C14

See VPG1

V17

M22

N23

R23

R22

U22

R18

U20

V23

V22

V21

V20

D15

U1

D2

W3

V4

D3

D3_CLS

D3_REV

D3_SPL

D4

P20

P21

N17

T7

D5

W2

V3

D6

D7

W1

T6

D8

D9

V2

DCD_DCE1

DCD_DTE1

DE

C10

D11

D16

AB19

Y16

AA18

AB18

M17

B10

A11

F10

C11

A10

E22

E23

W22

DQM0

DQM1

LBA

DQM2

LCS0

DQM3

LCS1

DRDY0

DSR_DCE1

DSR_DTE1

DTR_DCE1

DTR_DCE2

DTR_DTE1

DVFS0

DVFS1

EB0

LD0

LD1

LD10

LD11

LD12

LD13

LD14

LD15

LD16

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

104

Freescale Semiconductor

Package Information and Pinout

Table 64. 19 x 19 BGA Signal ID by Ball Grid Location (continued)

Signal ID

Ball Location

Signal ID

Ball Location

EB1

ECB

W21

Y21

M23

C19

G17

B20

T20

R17

U23

U18

T17

Y2

LD17

LD2

W23

R21

FPSHIFT

GPIO1_0

GPIO1_1

GPIO1_2

LD7

LD3

R20

LD4

T23

LD5

T22

LD6

T21

SCK6

SCLK0

SD_D_CLK

SD_D_I

SD_D_IO

SD0

R2

LD8

B19

LD9

M21

M20

M18

AC18

AA17

K2

M_GRANT

M_REQUEST

MA10

MCUPG

NFALE

See VPG0

T2

SD1

SD1_CLK

SD1_CMD

SD1_DATA0

SD1_DATA1

SD1_DATA2

SD1_DATA3

SD10

NFCE

R4

K3

NFCLE

NFRB

T1

K4

R3

J1

NFRE

T4

J2

NFWE

T3

L6

NFWP

P6

AB14

AC14

AA13

AB13

AC13

AA12

AC12

AA11

AB11

AC11

AB17

AA10

AB10

AC10

AC9

AA9

AC8

AB8

AC7

AA8

AB7

AC17

AA7

AC6

AA16

AC16

AA15

OE

T18

P22

G2

SD11

PAR_RS

PC_BVD1

PC_BVD2

PC_CD1

PC_CD2

PC_POE

PC_PWRON

PC_READY

PC_RST

PC_RW

PC_VS1

PC_VS2

PC_WAIT

POR

SD12

SD13

H4

SD14

J3

SD15

H1

SD16

J6

SD17

K6

SD18

H2

SD19

F1

SD2

G3

SD20

H3

SD21

G1

SD22

J4

SD23

F21

F20

F2

SD24

POWER_FAIL

PWMO

SD25

SD26

RAS

AA19

N18

F22

D10

B11

D15

B9

SD27

READ

SD28

RESET_IN

RI_DCE1

RI_DTE1

RTCK

SD29

SD3

SD30

SD31

RTS1

SD4

RTS2

B12

V18

SD5

RW

SD6

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

105

Product Documentation

Table 64. 19 x 19 BGA Signal ID by Ball Grid Location (continued)

Signal ID

Ball Location

Signal ID

Ball Location

RXD1

RXD2

C9

A12

P1

SD7

SD8

AB15

AC15

AA14

AA6

Y7

SCK3

SD9

SCK4

G6

SDBA0

SCK5

D4

SDBA1

SDCKE0

SDCKE1

SDCLK

SDQS0

SDQS1

SDQS2

SDQS3

SDWE

SER_RS

SFS3

Y17

V16

AC20

AC19

AB16

AB12

AB9

AB6

AB20

P23

P2

TRSTB

F15

D9

TXD1

TXD2

F11

C8

USB_BYP

USB_OC

B8

USB_PWR

USBH2_CLK

USBH2_DATA0

USBH2_DATA1

USBH2_DIR

USBH2_NXT

USBH2_STP

USBOTG_CLK

USBOTG_DATA0

USBOTG_DATA1

USBOTG_DATA2

USBOTG_DATA3

USBOTG_DATA4

USBOTG_DATA5

USBOTG_DATA6

USBOTG_DATA7

USBOTG_DIR

USBOTG_NXT

USBOTG_STP

VPG0

A8

L1

M6

K1

L2

L4

SFS4

D3

L3

SFS5

G7

D8

SFS6

P4

G8

SIMPD0

SJC_MOD

SRST0

SRX0

B18

C17

C18

A19

N3

C7

A6

F8

D7

SRXD3

SRXD4

SRXD5

SRXD6

STX0

B6

C3

A5

C4

C6

R1

A7

F16

N4

B7

STXD3

STXD4

STXD5

STXD6

SVEN0

TCK

F9

B3

G21

G22

H18

L22

N20

B21

N22

D1

VPG1

P3

VSTBY

D17

F14

A18

B17

C16

VSYNC0

VSYNC3

TDI

WATCHDOG_RST

WRITE

TDO

TMS

6 Product Documentation

This Data Sheet is labeled as a particular type: Product Preview, Advance Information, or Technical Data.

Definitions of these types are available at: http://www.freescale.com.

•

MCIMX31 Product Brief (order number MCIMX31PB)

MCIMX31 Reference Manual (order number MCIMX31RM)

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

106

Freescale Semiconductor

Revision History

•

MCIMX31 Chip Errata (order number MCIMX31CE)

The Freescale manuals are available on the Freescale Semiconductors Web site at

http://www.freescale.com/imx. These documents may be downloaded directly from the Freescale Web

site, or printed versions may be ordered. ARM Ltd. documentation is available from http://www.arm.com.

7 Revision History

Table 65 summarizes revisions to the MCIMX31C/MCIMX31LC Data Sheet since the release of Rev. 3.

Table 65. Revision History of the MCIMX31C/MCIMX31LC Data Sheet

Rev

Location

Change

4

Table 7, "Operating Ranges," on page 12

Operating Junction Temperature Range Max: changed from 100

to 105.

4.1 Table 1, "MCIMX31C and MCIMX31LC Ordering

Information," on page 3

Added new part numbers MCIMX31CVMN4D and

MCIMX31LCVMN4D.

4.1 Section 1.2.1, “Feature Differences Between TO2.0 and Added new section describing differences between silicon

TO 2.0.1

revisions.

4.2 Table 1, "MCIMX31C and MCIMX31LC Ordering

Information," on page 3

Added new part numbers MCIMX31CJMN4C and

MCIMX31LCJMN4D and a footnote.

4.3 Table 1, "MCIMX31C and MCIMX31LC Ordering

Information," on page 3

Added new part number MCIMX31CJMN4D.

MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3

Freescale Semiconductor

107

How to Reach Us:

Information in this document is provided solely to enable system and software implementers to use

Freescale Semiconductor products. There are no express or implied copyright licenses granted

hereunder to design or fabricate any integrated circuits or integrated circuits based on the information

in this document.

Home Page:

www.freescale.com

E-mail:

Freescale Semiconductor reserves the right to make changes without further notice to any products

herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the

suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any

liability arising out of the application or use of any product or circuit, and specifically disclaims any

and all liability, including without limitation consequential or incidental damages. “Typical” parameters

that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary

in different applications and actual performance may vary over time. All operating parameters,

including “Typicals”, must be validated for each customer application by customer’s technical experts.

Freescale Semiconductor does not convey any license under its patent rights nor the rights of others.

Freescale Semiconductor products are not designed, intended, or authorized for use as components

in systems intended for surgical implant into the body, or other applications intended to support or

sustain life, or for any other application in which the failure of the Freescale Semiconductor product

could create a situation where personal injury or death may occur. Should Buyer purchase or use

Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall

indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and

distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney

fees arising out of, directly or indirectly, any claim of personal injury or death associated with such

unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was

negligent regarding the design or manufacture of the part.

support@freescale.com

USA/Europe or Locations Not Listed:

Freescale Semiconductor

Technical Information Center, CH370

1300 N. Alma School Road

Chandler, Arizona 85224

+1-800-521-6274 or +1-480-768-2130

support@freescale.com

Europe, Middle East, and Africa:

Freescale Halbleiter Deutschland GmbH

Technical Information Center

Schatzbogen 7

81829 Muenchen, Germany

+44 1296 380 456 (English)

+46 8 52200080 (English)

+49 89 92103 559 (German)

+33 1 69 35 48 48 (French)

support@freescale.com

Japan:

Freescale Semiconductor Japan Ltd.

Headquarters

ARCO Tower 15F

1-8-1, Shimo-Meguro, Meguro-ku,

Tokyo 153-0064, Japan

0120 191014 or +81 3 5437 9125

support.japan@freescale.com

Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. ARM, ARM

Thumb, Jazelle, and the ARM Powered logo are registered trademarks of ARM Limited.

ARM1136JF-S, ARM11, Embedded Trace Kit, Embedded Trace Macrocell, ETM, Embedded Trace

Buffer, and ETB are trademarks of ARM Limited. All other product or service names are the property

of their respective owners. Java and all other Java-based marks are trademarks or registered

trademarks of Sun Microsystems, Inc. in the U.S. and other countries. France Telecom – TDF –

Groupe des ecoles des telecommunications Turbo codes patents license.

Asia/Pacific:

Freescale Semiconductor Hong Kong Ltd.

Technical Information Center

2 Dai King Street

Tai Po Industrial Estate

Tai Po, N.T., Hong Kong

+800 2666 8080

support.asia@freescale.com

For Literature Requests Only:

Freescale Semiconductor Literature Distribution Center

P.O. Box 5405

Denver, Colorado 80217

1-800-521-6274 or 303-675-2140

Fax: 303-675-2150

LDCForFreescaleSemiconductor@hibbertgroup.com

Document Number: MCIMX31C

Rev. 4.3

2/2010


型号：	MCIMX31C_10
厂家：	Freescale
描述：	Multimedia Applications Processors for Industrial and Automotive Products 多媒体应用处理器适用于工业和汽车产品
文件：	总108页 (文件大小：2884K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MCIMX31C_10 [FREESCALE]

相关型号：

MCIMX31DVKN5D

MCIMX31DVKN5D

MCIMX31DVMN5D

MCIMX31DVMN5D

MCIMX31L

MCIMX31LC

MCIMX31LCJKN5D

MCIMX31LCJMN4D

MCIMX31LCVKN5C

MCIMX31LCVKN5D

MCIMX31LCVKN5DR2

MCIMX31LCVMN4C