FT220X_技术文档

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Future Technology Devices

International Ltd

.

FT220X

(USB 4-BIT SPI/FT1248 IC)



USB Battery Charger Detection. Allows for USB

peripheral devices to detect the presence of a

higher power source to enable improved

charging.

The FT220X is a USB to FTDI’s

proprietary FT1248 interface and the

following advanced features:



FT1248 serial parallel interface in 1, 2 or 4 bit

wide mode.



Device supplied pre-programmed with unique

USB serial number.



Similar to an SPI slave in 1 bit mode

USB Power Configurations; supports bus-

powered, self-powered and bus-powered with

power switching.

Entire USB protocol handled on the chip. No

USB specific firmware programming required.



Integrated +3.3V level converter for USB I/O.



Fully

integrated

2048

byte

multi-time-

programmable (MTP) memory, storing device

descriptors and CBUS I/O configuration.

True 3.3V CMOS drive output and TTL input.

(operates down to 1V8 with external pull-ups)

Tolerant of 5V input.

Fully integrated clock generation with no

external crystal required plus optional clock

output selection enabling a glue-less interface

to external MCU or FPGA.



Configurable I/O pin output drive strength; 4

mA(min) and 16 mA(max)



Integrated power-on-reset circuit.



Data transfer rates to 500kByte/s.

Fully integrated AVCC supply filtering - no

external filtering required.

512 byte receive buffer and 512 byte transmit

buffer utilising buffer smoothing technology to

allow for high data throughput.



+ 5V Single Supply Operation.

Internal 3V3/1V8 LDO regulators



FTDI’s royalty-free Virtual Com Port (VCP) and

Direct

requirement for USB driver development in

most cases.

(D2XX)

drivers

eliminate

the

Low operating and USB suspend current; 8mA

(active-typ) and 125uA (suspend-typ).



Low USB bandwidth consumption.

UHCI/OHCI/EHCI host controller compatible.

USB 2.0 Full Speed compatible.

Configurable CBUS I/O pin.

Extended operating temperature range; -40 to

85⁰C.



Available in compact Pb-free 16 Pin SSOP and

QFN packages (both RoHS compliant).

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced

in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are

supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology

Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your

statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in

which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary

information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by

the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow

G41 1HH United Kingdom. Scotland Registered Company Number: SC136640

1

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

1 Typical Applications



USB to SPI interface in 1-bit mode

Upgrading Legacy Peripherals to USB

Utilising USB to add system modularity



USB Industrial Control

USB MP3 Player Interface

USB FLASH Card Reader and Writers

Set Top Box PC - USB interface

USB Digital Camera Interface

Incorporate USB interface to enable PC

transfers for development system

communication

USB dongle implementations for Software/

Hardware Encryption and Wireless Modules



Interfacing MCU/PLD/FPGA based designs to

add USB connectivity



Detect USB dedicated charging ports, to allow

for high current battery charging in portable

devices.

1.1 Driver Support

Royalty free VIRTUAL COM PORT

(VCP) DRIVERS for...

Royalty free D2XX Direct Drivers

(USB Drivers + DLL S/W Interface)



Windows 8 32,64-bit

Windows 7 32,64-bit

Windows Vista and Vista 64-bit

Windows XP and XP 64-bit

Server 2003, XP and Server 2008

Windows XP Embedded

Windows CE 4.2, 5.0 and 6.0

Mac OS-X



Windows 8 32,64-bit

Windows 7 32,64-bit

Windows Vista and Vista 64-bit

Windows XP and XP 64-bit

Server 2003, XP and Server 2008

Windows XP Embedded

Windows CE 4.2, 5.0 and 6.0

Mac OS-X

Linux 3.2 and greater

Android

Linux 2.6 and greater

Android

The drivers listed above are all available to download for free from FTDI website (www.ftdichip.com).

Various 3rd party drivers are also available for other operating systems - see FTDI website

(www.ftdichip.com) for details.

For driver installation, please refer to http://www.ftdichip.com/Documents/InstallGuides.htm

1.2 Part Numbers

Part Number

Package

FT220XQ-x

16 Pin QFN

16 Pin SSOP

FT220XS-x

Note: Packing codes for x is:

- R: Taped and Reel, (SSOP is 3,000pcs per reel, QFN is 5,000pcs per reel).

- U: Tube packing, 100pcs per tube (SSOP only)

- T: Tray packing, 490pcs per tray (QFN only)

For example: FT220XQ-R is 5,000pcs taped and reel packing

2

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

1.3 USB Compliant

The FT220X is fully compliant with the USB 2.0 specification and has been given the USB-IF Test-ID (TID)

40001461 (Rev D).

3

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

2 FT220X Block Diagram

VCC

1V8 Internal

Core Supply

3.3 Volt LDO

Regulator

1.8 Volt LDO

Regulator

3V3OUT

FIFO RX Buffer

(512 bytes)

VCCIO

MIOSI[0]

MIOSI[1]

MIOSI[2]

MIOSI[3]

USB

USBDP

USBDM

Transceiver

with

Integrated

1.5k pullups

and battery

charge

Serial Interface

Engine

USB

Protocol Engine

FT1248

Controller

(SIE)

CLK

CS#

detection

MISO

CBUS3

Internal MTP

Memory

USB DPLL

FIFO TX Buffer

(512 bytes)

3V3OUT

RESET#

Internal

12MHz

Oscillator

X4 Clock

Multiplier

Reset

Generator

48MHz

To USB Transceiver Cell

GND

Figure 2.1 FT220X Block Diagram

For a description of each function please refer to Section 4.

4

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Table of Contents

1

Typical Applications...................................................................... 2

1.1 Driver Support.................................................................................... 2

1.2 Part Numbers...................................................................................... 2

1.3 USB Compliant.................................................................................... 3

FT220X Block Diagram ................................................................. 4

Device Pin Out and Signal Description.......................................... 7

2

3

3.1 16-LD QFN Package ........................................................................... 7

3.1.1 QFN Package PinOut Description....................................................................................7

3.2 16-LD SSOP Package.......................................................................... 9

3.2.1 SSOP Package PinOut Description..................................................................................9

3.3 CBUS Signal Options ......................................................................... 11

4

5

Function Description................................................................... 12

4.1 Key Features..................................................................................... 12

4.2 Functional Block Descriptions........................................................... 12

FT1248 Interface Description..................................................... 14

5.1 Determining the Dynamic Bus Width ................................................ 14

5.2 Supported Commands on the FT1248 Interface................................ 15

5.3 LSB or MSB Selection........................................................................ 16

5.4 Clock Phase/Polarity ........................................................................ 16

5.4.1 CPHA = 1 ................................................................................................................. 17

5.5 FT1248 Timing.................................................................................. 18

6

7

Devices Characteristics and Ratings........................................... 20

6.1 Absolute Maximum Ratings............................................................... 20

6.2 ESD and Latch-up Specifications....................................................... 20

6.3 DC Characteristics............................................................................. 21

6.4 MTP Memory Reliability Characteristics ............................................ 25

6.5 Internal Clock Characteristics........................................................... 25

USB Power Configurations.......................................................... 26

7.1 USB Bus Powered Configuration ...................................................... 26

7.2 Self Powered Configuration .............................................................. 27

7.3 USB Bus Powered with Power Switching Configuration .................... 28

7.4 USB Battery Charging Detection ....................................................... 29

Application Examples ................................................................. 31

8.1 USB to FT1248 Converter.................................................................. 31

Internal MTP Memory Configuration........................................... 34

8

9

5

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

9.1 Default Values .................................................................................. 34

9.2 Method of Programming the MTP Memory ........................................ 35

9.2.1 Programming the MTP memory over USB...................................................................... 35

9.3 Memory Map ..................................................................................... 35

9.4 Hardware Requirements................................................................... 36

10 Package Parameters................................................................... 37

10.1

10.2

10.3

10.4

10.5

SSOP-16 Package Mechanical Dimensions ..................................... 37

SSOP-16 Package Markings............................................................ 38

QFN-16 Package Mechanical Dimensions ....................................... 39

QFN-16 Package Markings ............................................................. 40

Solder Reflow Profile ..................................................................... 41

11 Contact Information................................................................... 42

Appendix A – References........................................................................... 43

Appendix B - List of Figures and Tables..................................................... 44

Appendix C - Revision History.................................................................... 46

6

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

3 Device Pin Out and Signal Description

3.1 16-LD QFN Package

8

15

2

16

4

3V3OUT

MIOSI0

MIOSI1

MIOSI2

MIOSI3

7

6

USBDM

USBDP

12

11

5

CLK

CS#

MISO

CBUS3

9

RESET#

14

Figure 3.1 QFN Schematic Symbol

3.1.1 QFN Package PinOut Description

Note: # denotes an active low signal.

Pin No.

Name

Type

Description

**

POWER

Input

10

5 V (or 3V3) supply to IC

VCC

POWER

Input

1

8

VCCIO

1V8 - 3V3 supply for the IO cells

3V3 output at 50mA. May be used to power VCCIO.

**

POWER

Output

When VCC is 3V3; pin 8 is an input pin. Connect to pin

10.

3V3OUT

POWER

Input

3, 13

GND

0V Ground input.

Table 3.1 Power and Ground

*Pin 17 is centre pad on base of chip package. Connect to GND.

** If VCC is 3V3 then 3V3OUT must also be driven with 3V3 input

Pin No.

Name

USBDM

USBDP

RESET#

Type

INPUT

Description

7

6

9

USB Data Signal Minus.

USB Data Signal Plus.

Reset input (active low).

Table 3.2 Common Function pins

7

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Pin No.

Name

MIOSI[0]

MIOSI[1]

MIOSI[2]

MIOSI[3]

CLK

Type

I/O

Description

15

2

Bi-Directional data bit 0

I/O

Bi-Directional data bit 1

16

4

I/O

Bi-Directional data bit 2

I/O

Bi-Directional data bit 3

12

11

Input

Clock input from FT1248 interface master

Chip select input to enable the device interface. Active low logic.

CS#

Master In Slave Out. Used to provide status information to the FT1248

interface master.

5

MISO

Output

I/O

Configurable CBUS I/O Pin. Function of this pin is configured in the

device MTP memory. See CBUS Signal Options, Table 3.7.

14

CBUS3

Table 3.3 FT1248 Interface and CBUS Group (see note 1)

Notes:

1. When used in Input Mode, the input pins are pulled to VCCIO via internal 75kΩ (approx) resistors.

These pins can be programmed to gently pull low during USB suspend (PWREN# = “1”) by setting an

option in the MTP memory.

8

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

3.2 16-LD SSOP Package

10

1

4

2

6

3V3OUT

MIOSI0

MIOSI1

MIOSI2

MIOSI3

9

8

USBDM

USBDP

15

14

7

CLK

CS#

MISO

11

RESET#

16

CBUS3

Figure 3.2 SSOP Schematic Symbol

3.2.1 SSOP Package PinOut Description

Note : # denotes an active low signal.

Pin No.

Name

Type

Description

**

POWER

Input

12

5 V (or 3V3) supply to IC

VCC

POWER

Input

3

VCCIO

1V8 - 3V3 supply for the IO cells

3V3 output at 50mA. May be used to power VCCIO.

**

POWER

Output

10

When VCC is 3V3; pin 10 is an input pin. Connect to

pin 12.

3V3OUT

POWER

Input

5, 13

GND

0V Ground input.

Table 3.4 Power and Ground

** If VCC is 3V3 then 3V3OUT must also be driven with 3V3 input

Pin No.

Name

USBDM

USBDP

RESET#

Type

INPUT

Description

9

8

USB Data Signal Minus.

USB Data Signal Plus.

Reset input (active low).

11

Table 3.5 Common Function pins

9

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Pin No.

Name

MIOSI[0]

MIOSI[1]

MIOSI[2]

MIOSI[3]

CLK

Type

I/O

Description

1

4

Bi-Directional data bit 0

I/O

Bi-Directional data bit 1

2

I/O

Bi-Directional data bit 2

6

I/O

Bi-Directional data bit 3

15

14

Input

Clock input from FT1248 interface master

Chip select input to enable the device interface. Active low logic.

CS#

Master In Slave Out. Used to provide status information to the FT1248

interface master.

7

MISO

Output

I/O

Configurable CBUS I/O Pin. Function of this pin is configured in the

device MTP memory. See CBUS Signal Options, Table 3.7.

16

CBUS3

Table 3.6 FT1248 Interface and CBUS Group (see note 1)

Notes:

1. When used in Input Mode, the input pins are pulled to VCCIO via internal 75kΩ (approx) resistors.

These pins can be programmed to gently pull low during USB suspend (PWREN# = “1”) by setting an

option in the MTP memory.

10

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

3.3 CBUS Signal Options

The following options can be configured on the CBUS I/O pin. CBUS signal options are common to both

package versions of the FT220X. These options can be configured in the internal MTP memory using the

software utility FT_PROG, which can be downloaded from the FTDI Utilities (www.ftdichip.com). The

default configuration is described in Section 9.

CBUS

Signal

Option

Available On CBUS Pin

Description

TRI-STATE

DRIVE 1

DRIVE 0

CBUS3

IO Pad is tri-stated

Output a constant 1

Output a constant 0

Output is low after the device has been configured by

USB, then high during USB suspend mode. This output can

be used to control power to external logic P-Channel logic

level MOSFET switch. Enable the interface pull-down

option when using the PWREN# in this way.

PWREN#

SLEEP#

CBUS3

Goes low during USB suspend mode. Typically used to

power down an external TTL to RS232 level converter IC

in USB to RS232 converter designs.

CLK24MHz

CLK12MHz

CLK6MHz

CBUS3

24 MHz Clock output.*

12 MHz Clock output.*

6 MHz Clock output.*

CBUS bit bang mode option. Allows the CBUS pins to be

used as general purpose I/O. Configured in the internal

MTP memory. A separate application note, AN232R-01,

available from FTDI website (www.ftdichip.com) describes

in more detail how to use CBUS bit bang mode.

GPIO

CBUS3

Battery Charger Detect, indicates when the device is

connected to a dedicated battery charger port. Active high

output.

BCD Charger

BCD

Charger#

CBUS3

Inverse of BCD Charger (open drain)

Synchronous and asynchronous bit bang mode WR#

strobe output.

BitBang_WR#

Synchronous and asynchronous bit bang mode RD# strobe

output.

BitBang_RD#

VBUS Sense

Time Stamp

CBUS3

Input to detect when VBUS is present.

Toggle signal which changes state each time a USB SOF is

received

Prevents the device from entering suspend state when

unplugged.

Keep_Awake#

CBUS3

Table 3.7 CBUS Configuration Control

*When in USB suspend mode the outputs clocks are also suspended.

11

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

4 Function Description

The FT220X is a USB to FTDI Proprietary FT1248 interface device which simplifies USB implementations

and reduces external component count by fully integrating an MTP memory and an integrated clock

circuit which requires no external crystal. It has been designed to operate efficiently with USB host

controllers by using as little bandwidth as possible when compared to the total USB bandwidth available.

4.1 Key Features

Functional Integration. Fully integrated MTP memory, clock generation, AVCC filtering, Power-On-

Reset and LDO regulator.

Configurable CBUS I/O Pin Options. The fully integrated MTP memory allows configuration of the

Control Bus (CBUS) functionality and drive strength selection. There is 1 configurable CBUS I/O pin. The

configurable options are defined in section 3.3.

The CBUS line can be configured with any one of these output options by setting bits in the internal MTP

memory. The device is supplied with the most commonly used pin definitions pre-programmed - see

Section 9 for details.

Asynchronous Bit Bang Mode with RD# and WR# Strobes. The FT220X supports FTDI’s previous

chip generation bit-bang mode. In bit-bang mode, the 4 MIOSI data lines can be switched from the

regular interface mode to a 4-bit general purpose I/O port. Data packets can be sent to the device and

they will be sequentially sent to the interface at a rate controlled by an internal timer (equivalent to the

baud rate pre-scalar).

Synchronous Bit Bang Mode. The FT220X supports synchronous bit bang mode. This mode differs from

asynchronous bit bang mode in that the interface pins are only read when the device is written to. This

makes it easier for the controlling program to measure the response to an output stimulus as the data

returned is synchronous to the output data. An application note, AN232R-01, available from FTDI website

(www.ftdichip.com) describes this feature.

Source Power and Power Consumption. The FT220X is capable of operating at a voltage supply

between +3.3V and +5.25V with a nominal operational mode current of 8mA and a nominal USB suspend

mode current of 125µA. This allows greater margin for peripheral designs to meet the USB suspend mode

current limit of 2.5mA. An integrated level converter within the FT1248 interface allows the FT220X to

interface to logic running at +1.8V, 2.5V, +3.3V or +5V. (Note: External pull-ups are recommended for

IO <3V3).

4.2 Functional Block Descriptions

The following paragraphs detail each function within the FT220X. Please refer to the block diagram shown

in Figure 2.1

Internal MTP Memory. The internal MTP memory in the FT220X is used to store USB Vendor ID (VID),

Product ID (PID), device serial number, product description string and various other USB configuration

descriptors. The internal MTP memory is also used to configure the CBUS pin functions. The FT220X is

supplied with the internal MTP memory pre-programmed as described in Section 9. A user area of the

internal MTP memory is available to system designers to allow storing additional data from the user

application over USB. The internal MTP memory descriptors can be programmed in circuit, over USB

without any additional voltage requirement. The descriptors can be programmed using the FTDI utility

software called FT_PROG, which can be downloaded from FTDI Utilities on the FTDI website

(www.ftdichip.com).

+1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8V reference voltage for driving the

internal core of the IC.

+3.3V LDO Regulator. The +3.3V LDO regulator generates the +3.3V reference voltage for driving the

USB transceiver cell output buffers. It requires an external decoupling capacitor to be attached to the

3V3OUT regulator output pin. It also provides +3.3V power to the 1.5kΩ internal pull up resistor on

USBDP. The main function of the LDO is to power the USB Transceiver and the Reset Generator Cells

rather than to power external logic. However, it can be used to supply external circuitry requiring a

+3.3V nominal supply with a maximum current of 50mA.

USB Transceiver. The USB Transceiver Cell provides the USB 1.1 / USB 2.0 full-speed physical interface

to the USB cable. The output drivers provide +3.3V level slew rate control signalling, whilst a differential

12

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

input receiver and two single ended input receivers provide USB data in, Single-Ended-0 (SE0) and USB

reset detection conditions respectfully. This function also incorporates a 1.5kΩ pull up resistor on USBDP.

The block also detects when connected to a USB power supply which will not enumerate the device but

still supply power and may be used for battery charging.

USB DPLL. The USB DPLL cell locks on to the incoming NRZI USB data and generates recovered clock

and data signals for the Serial Interface Engine (SIE) block.

Internal 12MHz Oscillator - The Internal 12MHz Oscillator cell generates a 12MHz reference clock. This

provides an input to the x4 Clock Multiplier function. The 12MHz Oscillator is also used as the reference

clock for the SIE, USB Protocol Engine and UART FIFO controller blocks.

Clock Multiplier / Divider. The Clock Multiplier / Divider takes the 12MHz input from the Internal

Oscillator function and generates the 48MHz, 24MHz, 12MHz and 6MHz reference clock signals. The 48Mz

clock reference is used by the USB DPLL and the Baud Rate Generator blocks.

Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial

and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it

performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data

stream.

USB Protocol Engine. The USB Protocol Engine manages the data stream from the device USB control

endpoint. It handles the low level USB protocol requests generated by the USB host controller and the

commands for controlling the functional parameters of the FT1245 in accordance with the USB 2.0

specification chapter 9.

FIFO RX Buffer (512 bytes). Data sent from the USB host controller to the FT1248 interface via the

USB data OUT endpoint is stored in the FIFO RX (receive) buffer. Data is removed from the buffer to the

FT1248 transmit register under control of the FT1248 FIFO controller. (Rx relative to the USB interface).

FIFO TX Buffer (512 bytes). Data from the FT1248 receive register is stored in the TX buffer. The USB

host controller removes data from the FIFO TX Buffer by sending a USB request for data from the device

data IN endpoint. (Tx relative to the USB interface).

FT1248 interface controller. Controls the FT1248 interface, dynamically switching the width of the bus

as commanded by the external bus master.

RESET Generator - The integrated Reset Generator Cell provides a reliable power-on reset to the device

internal circuitry at power up. The RESET# input pin allows an external device to reset the FT220X.

RESET# can be tied to 3V3OUT.

13

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

5 FT1248 Interface Description.

The FT1248 protocol has a dynamic bi-directional data bus interface that can be configured as 1, 2, 4, or

8-bits wide (only 4 bit wide on the FT220X) providing users with the flexibility to configure the interface

with performance, pin count and PCB area in mind. For example, 1-bit mode it requires 8 clock cycles to

get 8 data bits and in 8-bit mode all 8 bits are sent with one clock.

In the FT1248 there are 3 distinct phases:

While CS# is inactive, the FT1248 reflects the status of the write buffer and read buffers within the

FT220X on the MIOSIO[0] and MISO wires respectively. The buffers are 512 Bytes each and the status

will reflect if at least one byte of space is available for the external device to write to and whether at least

one byte is available to be read by the external device.

Additionally, the FT1248 slave block supports multiple slave devices where a master can communicate

with multiple SPI slave devices. When the slave is sharing buses with other SPI slave devices, the write

and read buffer status cannot be reflected on the MIOSIO[0] and MISO wires during CS# inactivity as

this would cause bus contention. Therefore, it is possible for the user to select whether they wish to have

the buffer status switched on or off during inactivity.

(This setting may be applied in the internal MTP memory with FT_PROG at the same time as selecting

FT1248 mode).

When CS# is active a command/bus size phase occurs first. Following the command phase is the data

phase, for each data byte transferred the FT1248 slave drives an ACK/NAK status onto the MISO wire.

The master can send multiple data bytes so long as CS# is active, if a unsuccessful data transfer occurs,

i.e. a NAK happens on the MISO wire then the master should immediately abort the transfer by de-

asserting CS#.

Figure 5.1: FT1248 Basic Waveform Protocol.

5.1 Determining the Dynamic Bus Width

The bus width is dynamic. In order for the FT220X, in FT1248 mode, to determine the bus width within

the command phase, the bus width is encoded along with the actual commands on the first active clock

edge when CS# is active and has a data width of 4-bits.

If any of the MIOSIO[3:2] signals are driven low by the external host then the data transfer width equals

4-bits

If MIOSIO[1] signal is driven low by the external host then the data transfer width equals 2-bits

Else the bus width is defaulted to 1-bit

In order to successfully decode the bus width, all MIOSIO signals must have pull up resistors. By default,

all MIOSIO signals shall be seen by the FT220X in FT1248 mode as logic ‘1’from the internal resistors.

This means that when a FT1248 master does not wish to use certain MIOSIO signals, the slave (FT220X)

is still capable of determining the requested bus width since any unused MIOSIO signals shall be pulled

up by default.

The remaining bits used during the command phase are used to contain the command itself which means

that it is possible to define up to 16 unique commands.

14

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

LSB

CMD[3]

0

MSB

BWID 2-bit BWID 4-bit

CMD[2]

3

BWID 8-bit

4

CMD[1]

5

CMD [0]

6

X

7

1

2

1-bit Bus

Width

CMD[3]

0

X

1

X

2

CMD[2]

3

X

4

CMD[1]

5

CMD [0]

6

X

7

2-bit Bus

Width

CMD[3]

0

1

X

2

CMD[2]

3

X

4

CMD[1]

5

CMD [0]

6

X

7

4-bit Bus

Width

CMD[3]

0

X

1

0

2

CMD[2]

3

X

4

CMD[1]

5

CMD [0]

6

X

7

Figure 5.2: FT1248 Command Structure

5.2 Supported Commands on the FT1248 Interface

The FT1248 interface can accept and decode up to 16 unique commands. At this time only 9 unique

commands are implemented as shown below.

Command

write

Identifier

0x00

Description

Write request command

Read request command

read

0x01

read modem status

0x02

Read modem status command, users may wish to emulate

modem status control. A RMS command returns status bits

RTS and DTR

write modem status

write buffer flush

0x03

0x04

Write modem status command, users may wish to emulate

modem status control. A WMS command allows users to set

status bits: DCD, RI, DSR, CTS

Write buffer flush request – This command is used to indicate

to the FT1248 slave that its write buffers should be flushed

rather than wait for any latency timers to expire. If this

command is received the FT1248 block will flag the upstream

controllers (USB FIFOs etc) to flush their write buffers

regardless of what content is present in the FT1248 write

buffer

15

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

address eeprom

write eeprom

0x05

0x06

Address EEPROM command sets the address users wish to

write or read from

Write EEPROM command sets the write data to be written into

the EEPROM

read eeprom

0x07

0x08

Read EEPROM command reads

Read USB Status:

read usb status

00 = suspended, 01 = default, 10 = addressed, 11 =

configured

Reserved

0x09 – 0xF

Unused Commands

Table 5.1: FT1248 Commands

5.3 LSB or MSB Selection

The data can be sent/received Least Significant Bit First (LSB) or Most Significant Bit First (MSB). To

determine which mode is used by the FT1248 interface of the FT220X the MTP memory must be set.

This may be selected with FT_PROG.

5.4 Clock Phase/Polarity

The FT1248 slave does not need to have any knowledge of clock rate as this is supplied by the FT1248

master. However the relationship between clock and data needs to be controllable, to allow the slave to

operate in the same way as the master such that data is correctly driven and sampled on the correct

clock phases. By configuring the polarity and phase of CLK with respect to the data it is possible to match

the FT1248 master.

There are 4 possible modes which are determined by the Clock Polarity (CPOL) and Clock Phase (CPHA)

signals. The different combinations of these signals are commonly referred to as modes, see Table 5.2

below. For the FT1248 slave, only 2 of these 4 modes are supported. CPHA will always be set to 1 in the

FT1248 slave because data is available or driven on to MIOSIO wires on the first clock edge after CS# is

active and is therefore sampled on the trailing edge of the first clock pulse. When CPHA equals 0, it

means data must be available or driven onto the MIOSIO wires on the first leading edge of the clock after

CS# is active. However, during this period between CS# becoming active and the first leading clock edge

is when the MIOSIO wires are being “turned around” as when CS# is inactive the FT1248 slave is driving

the write buffer status. Supporting CPHA = 0 would result in bus contention and therefore, shall not be

supported.

Mode

CPOL

CPHA

Supported

NO

0

1

2

3

0

1

0

1

0

1

YES

NO

YES

Table 5.2: CPOL & CPHA Mode Numbers

When CPOL is 1, the idle state of the clock is high. When CPOL is 0, the idle state of the clock is low. It

should be noted that clock phase and polarity need to be identical for the master and attached slave

device.

16

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

5.4.1 CPHA = 1

When CPHA is set to ‘1’, the first edge after CS# goes low will be used to shift (or drive) the first data bit

onto MIOSIO. Every odd numbered edge after this will shift out the next data bit. Incoming data will be

sampled on the second or trailing SCLK edge and every even edge thereafter.

Figure 5.3 shows this for both CPOL = 0 and CPOL = 1.

start of

Transfer

end of idle

start

end

next idle

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16

SCK Edge No.

SCK (CPOL = 0)

SCK (CPOL = 1)

SS_n

CPHA = 1

Sample

0

1

2

3

4

5

6

7

MISO

MOSI

2

3

Figure 5.3: FT1248 Clock Format CPHA = 1

Note: The CPOL value may be selected in the MTP memory. This may be done with FT_PROG.

Note: Further information on this interface can be found in AN_167_FT1248 Parallel Serial Interface

Basics from the FTDI website www.ftdichip.com.

17

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

5.5 FT1248 Timing

Figure 5.4: FT1248 Clock Format CPHA = 1

The timings will vary depending on VCCIO.

Min (ns)

Typical (ns)

83.33

41.67

1

Max (ns)

Description

SCLK Period

SCLK HIGH

SCLK LOW

T1

T2

T3

T4

30

SCLK rising or falling driving edge to

MIOSIO/MSIO

T5

T6

25

3

MIOSIO setup time to rising or falling sample

SCLK edge

MIOSIO hold time from rising or falling sample

SCLK edge

T7

T8

5

SS_n setup time to rising or falling SCLK edge

SS_n hold time from rising or falling sample SCLK

edge

Table 5.3: 1V8 VCCIO timings

18

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Min (ns)

Typical (ns)

83.33ns

41.67ns

1

Max (ns)

Description

SCLK Period

SCLK HIGH

SCLK LOW

T1

T2

T3

T4

15

SCLK rising or falling driving edge to

MIOSIO/MSIO

T5

T6

22

1

MIOSIO setup time to rising or falling sample

SCLK edge

MIOSIO hold time from rising or falling sample

SCLK edge

T7

T8

5

SS_n setup time to rising or falling SCLK edge

SS_n hold time from rising or falling sample SCLK

edge

Table 5.4: 2V5 VCCIO timings

Min (ns)

Typical (ns)

Max (ns)

Description

SCLK Period

SCLK HIGH

SCLK LOW

T1

T2

T3

T4

83.33ns

41.67ns

1

10

SCLK rising or falling driving edge to

MIOSIO/MSIO

T5

T6

20

0

MIOSIO setup time to rising or falling sample

SCLK edge

MIOSIO hold time from rising or falling sample

SCLK edge

T7

T8

5

SS_n setup time to rising or falling SCLK edge

SS_n hold time from rising or falling sample SCLK

edge

Table 5.5: 3V3 VCCIO timings

19

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

6 Devices Characteristics and Ratings

6.1 Absolute Maximum Ratings

The absolute maximum ratings for the FT220X devices are as follows. These are in accordance with the

Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the

device.

Parameter

Value

Unit

Conditions

Storage Temperature

-65°C to 150°C

168 Hours

Degrees C

Floor Life (Out of Bag) At Factory Ambient

(30°C / 60% Relative Humidity)

(IPC/JEDEC J-

STD-033A MSL

Level 3

Hours

Compliant)*

Ambient Operating Temperature (Power

Applied)

-40°C to 85°C

Degrees C

MTTF FT220XS

MTTF FT220XQ

TBD

Hours

TBD

Hours

VCC Supply Voltage

-0.3 to +5.5

-0.3 to +4.0

-0.5 to +3.63

V

VCCIO IO Voltage

DC Input Voltage – USBDP and USBDM

DC Input Voltage – High Impedance

-0.3 to +5.8

V

Bi-directionals (powered from VCCIO)

DC Output Current – Outputs

22

mA

V

ESD Charge Device Mode(CDM)

500

Class III

Class 2

ESD Human Body Mode (HDM)

2000

V

Table 6.1 Absolute Maximum Ratings

* If devices are stored out of the packaging beyond this time limit the devices should be baked before

use. The devices should be ramped up to a temperature of +125°C and baked for up to 17 hours.

6.2 ESD and Latch-up Specifications

Description

Specification

Human Body Mode (HBM)

Machine mode (MM)

> ± 2kV

> ± 200V

> ± 500V

> ± 200mA

Charged Device Mode (CDM)

Latch-up

Table 6.2 ESD and Latch-Up Specifications

20

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

6.3 DC Characteristics

DC Characteristics (Ambient Temperature = -40°C to +85°C)

Parameter

Description

Minimum

Typical

Maximum

5.5

Units

V

Conditions

VCC Operating Supply

Voltage

VCC

2.97

5

Normal Operation

VCCIO Operating

Supply Voltage

VCC2

Icc1

1.62

---

3.63

V

Operating Supply

Current

9.7

10.5

125

12.3

mA

μA

Normal Operation

USB Suspend

Operating Supply

Current

Icc2

VCC must be

greater than 3V3

otherwise 3V3OUT

is an input which

must be driven

with 3.3V

3V3

3.3v regulator output

2.97

3.3

3.63

V

Table 6.3 Operating Voltage and Current

21

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Ioh = +/-2mA

2.97

VCCIO

V

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

2.97

VCCIO

V

Voh

Output Voltage High

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Iol = +/-2mA

V

0

0.4

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

V

0

0.4

0.8

Vol

Output Voltage Low

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Input low Switching

Threshold

Vil

LVTTL

Input High Switching

Threshold

Vih

LVTTL

2.0

Vt

Switching Threshold

V

1.49

1.15

Schmitt trigger negative

going threshold voltage

Vt-

Schmitt trigger positive

going threshold voltage

Vt+

Rpu

Rpd

Iin

V

1.64

75

Input pull-up resistance

40

190

10

KΩ

μA

Vin = 0

Vin =VCCIO

Vin = 0

Input pull-down

resistance

75

Input Leakage Current

-10

+/-1

Tri-state output leakage

current

Ioz

10

Vin = 5.5V or 0

Table 6.4 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins)

* The I/O drive strength and slow slew-rate are configurable in the MTP memory.

22

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Ioh = +/-2mA

2.25

VCCIO

V

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

2.25

VCCIO

V

Voh

Output Voltage High

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Iol = +/-2mA

V

0

0.4

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

V

0

0.4

0.8

Vol

Output Voltage Low

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Input low Switching

Threshold

Vil

LVTTL

Input High Switching

Threshold

Vih

LVTTL

0.8

Vt

Switching Threshold

V

1.1

0.8

Schmitt trigger negative

going threshold voltage

Vt-

Schmitt trigger positive

going threshold voltage

Vt+

Rpu

Rpd

Iin

V

1.2

75

Input pull-up resistance

40

190

10

KΩ

μA

Vin = 0

Vin =VCCIO

Vin = 0

Input pull-down

resistance

75

Input Leakage Current

-10

+/-1

Tri-state output leakage

current

Ioz

10

Vin = 5.5V or 0

Table 6.5 I/O Pin Characteristics VCCIO = +2.5V (except USB PHY pins)

* The I/O drive strength and slow slew-rate are configurable in the MTP memory.

23

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Ioh = +/-2mA

1.62

VCCIO

V

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

1.62

VCCIO

V

Voh

Output Voltage High

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Iol = +/-2mA

V

0

0.4

I/O Drive strength*

= 4mA

I/O Drive strength*

= 8mA

V

0

0.4

0.77

Vol

Output Voltage Low

I/O Drive strength*

= 12mA

I/O Drive strength*

= 16mA

Input low Switching

Threshold

Vil

LVTTL

Input High Switching

Threshold

Vih

LVTTL

1.6

Vt

Switching Threshold

V

0.77

Schmitt trigger negative

going threshold voltage

Vt-

0.557

Schmitt trigger positive

going threshold voltage

Vt+

Rpu

Rpd

Iin

V

0.893

75

Input pull-up resistance

40

190

10

KΩ

μA

Vin = 0

Vin =VCCIO

Vin = 0

Input pull-down

resistance

75

Input Leakage Current

-10

+/-1

Tri-state output leakage

current

Ioz

10

Vin = 5.5V or 0

Table 6.6 I/O Pin Characteristics VCCIO = +1.8V (except USB PHY pins)

* The I/O drive strength and slow slew-rate are configurable in the MTP memory.

24

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Parameter

Description

Minimum

Typical

Maximum

Units

Conditions

Voh

Vol

Output Voltage High

Output Voltage Low

VCC-0.2

V

0.2

0.8

Input low Switching

Threshold

Vil

V

-

Input High Switching

Threshold

Vih

2.0

Table 6.7 USB I/O Pin (USBDP, USBDM) Characteristics

6.4 MTP Memory Reliability Characteristics

The internal 2048 Bytes MTP memory has the following reliability characteristics:

Parameter

Data Retention

Write Cycle

Value

10

Unit

Years

Cycles

2,000

Read Cycle

Unlimited

Table 6.8 MTP Memory Characteristics

6.5 Internal Clock Characteristics

The internal Clock Oscillator has the following characteristics:

Value

Parameter

Unit

Minimum

11.98

Typical

12.00

Maximum

12.02

Frequency of Operation

(see Note 1)

MHz

Clock Period

Duty Cycle

83.19

45

83.33

50

83.47

55

ns

%

Table 6.9 Internal Clock Characteristics

Note 1: Equivalent to +/-1667ppm

25

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

7 USB Power Configurations

The following sections illustrate possible USB power configurations for the FT220X. The illustrations have

omitted pin numbers for ease of understanding since the pins differ between the FT220XS and FT220XQ

package options.

All USB power configurations illustrated apply to both package options for the FT220X device. Please refer

to Section 3 for the package option pin-out and signal descriptions.

7.1 USB Bus Powered Configuration

VCC

Ferrite

Bead

1

VCC

27R

2

USBDM

3

4

27R

USBDP

FT220X

47pF

10nF

47pF

5

RESET#

VCCIO

SHIELD

GND

3V3OUT

D

N

D

GND

N

G

A

G

VCC

100nF

+

4.7uF

100nF

GND

Figure 7.1 Bus Powered Configuration

Figure 7.1 Illustrates the FT220X in a typical USB bus powered design configuration. A USB bus powered

device gets its power from the USB bus. Basic rules for USB bus power devices are as follows –

i)

ii)

iii)

On plug-in to USB, the device should draw no more current than 100mA.

In USB Suspend mode the device should draw no more than 2.5mA.

A bus powered high power USB device (one that draws more than 100mA) should use one of

the CBUS pins configured as PWREN# and use it to keep the current below 100mA on plug-in

and 2.5mA on USB suspend.

iv)

v)

A device that consumes more than 100mA cannot be plugged into a USB bus powered hub.

No device can draw more than 500mA from the USB bus.

The power descriptors in the internal MTP memory of the FT220X should be programmed to match the

current drawn by the device.

A ferrite bead is connected in series with the USB power supply to reduce EMI noise from the FT220X and

associated circuitry being radiated down the USB cable to the USB host. The value of the Ferrite Bead

depends on the total current drawn by the application. A suitable range of Ferrite Beads is available from

Steward (www.steward.com), for example Steward Part # MI0805K400R-10.

Note: If using PWREN# (available using the CBUS) the pin should be pulled to VCCIO using a 10kΩ

resistor.

26

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

7.2 Self Powered Configuration

VCC(3.3-5.25V)

1

VCC

27R

2

3

USBDM

USBDP

4

47pF

4k7

FT220X

5

RESET#

VCCIO

SHIELD

GND

10k

GND

3V3OUT

D

N

D

N

G

A

G

GND

VCC

100nF

+

4.7uF

GND

Figure 7.2 Self Powered Configuration

Figure 7.2 illustrates the FT220X in a typical USB self powered configuration. A USB self powered device

gets its power from its own power supply, VCC, and does not draw current from the USB bus. The basic

rules for USB self powered devices are as follows –

i)

A self powered device should not force current down the USB bus when the USB host or hub

controller is powered down.

ii)

iii)

A self powered device can use as much current as it needs during normal operation and USB

suspend as it has its own power supply.

A self powered device can be used with any USB host, a bus powered USB hub or a self

powered USB hub.

The power descriptor in the internal MTP memory of the FT220X should be programmed to a value of

zero (self powered).

In order to comply with the first requirement above, the USB bus power (pin 1) is used to control the

VBUS_Sense pin of the FT220X device. When the USB host or hub is powered up an internal 1.5kΩ

resistor on USBDP is pulled up to +3.3V, thus identifying the device as a full speed device to the USB

host or hub. When the USB host or hub is powered off, VBUS_Sense pin will be low and the FT220X is

held in a suspend state. In this state the internal 1.5kΩ resistor is not pulled up to any power supply

(hub or host is powered down), so no current flows down USBDP via the 1.5kΩ pull-up resistor. Failure to

do this may cause some USB host or hub controllers to power up erratically.

Figure 7.2 illustrates a self powered design which has a +3.3V to +5.25V supply.

Note:

1. When the FT220X is in reset, the FT1248 interface I/O pins are tri-stated. Input pins have

internal 75kΩ pull-up resistors to VCCIO, so they will gently pull high unless driven by some

external logic.

27

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

7.3 USB Bus Powered with Power Switching Configuration

P Channel Power

MOSFET

Switched 5V Power to

External Logic

0.1uF

100k

1k

PWREN#

Ferrite

Bead

1

VCC

27R

2

3

USBDM

USBDP

4

47pF

FT220X

5

RESET#

VCCIO

SHIELD

10nF

GND

3V3OUT

CBUS3

D

N

D

N

GND

G

A

G

VCC

100nF

+

4.7uF

100nF

GND

Figure 7.3 Bus Powered with Power Switching Configuration

A requirement of USB bus powered applications, is when in USB suspend mode, the application draws a

total current of less than 2.5mA. This requirement includes external logic. Some external logic has the

ability to power itself down into a low current state by monitoring the PWREN# signal. For external logic

that cannot power itself down in this way, the FT220X provides a simple but effective method of turning

off power during the USB suspend mode.

Figure 7.3 shows an example of using a discrete P-Channel MOSFET to control the power to external

logic. A suitable device to do this is an International Rectifier (www.irf.com) IRLML6402, or equivalent. It

is recommended that a “soft start” circuit consisting of a 1kΩ series resistor and a 0.1μF capacitor is used

to limit the current surge when the MOSFET turns on. Without the soft start circuit it is possible that the

transient power surge, caused when the MOSFET switches on, will reset the FT220X or the USB host/hub

controller. The soft start circuit example shown in Figure 7.3 powers up with a slew rate of

approximaely12.5V/ms. Thus supply voltage to external logic transitions from GND to +5V in

approximately 400 microseconds.

As an alternative to the MOSFET, a dedicated power switch IC with inbuilt “soft-start” can be used. A

suitable power switch IC for such an application is the Micrel (www.micrel.com) MIC2025-2BM or

equivalent.

With power switching controlled designs the following should be noted:

i) The external logic to which the power is being switched should have its own reset circuitry to

automatically reset the logic when power is re-applied when moving out of suspend mode.

ii) Set the Pull-down on Suspend option in the internal FT220X MTP memory.

iii) One of the CBUS Pins should be configured as PWREN# in the internal FT220X MTP memory, and

used to switch the power supply to the external circuitry.

iv) For USB high-power bus powered applications (one that consumes greater than 100mA, and up

to 500mA of current from the USB bus), the power consumption of the application must be set in

the Max Power field in the internal FT220X MTP memory. A high-power bus powered application

uses the descriptor in the internal FT220X MTP memory to inform the system of its power

requirements.

v) PWREN# gets its VCC from VCCIO. For designs using 3V3 logic, ensure VCCIO is not powered

down using the external logic. In this case use the +3V3OUT.

28

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

7.4 USB Battery Charging Detection

A recent addition to the USB specification

(http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip ) is to allow for additional charging

profiles to be used for charging batteries in portable devices. These charging profiles do not enumerate

the USB port of the peripheral. The FT220X device will detect that a USB compliant dedicated charging

port (DCP) is connected. Once detected while in suspend mode a battery charge detection signal is then

provided to allow external logic to switch to charging mode as opposed to operation mode.

VBUS

3V3OUT

VBUS 3V3OUT

VBUS

3V3OUT

0.1uF

600R/2A

3V3OUT

CN USB

VBUS

1

2

3

4

5

GND

D-

D+

ID

DM

DP

27R

GND

RESET#

10nF

N.F.

BCD

0.1uF

CBUS3

FT220X

0R

SLD GND

GND

VBUS VBUS

VBUS

VBATT

4.7uF

0.1uF

1

2

3

4

5

10

9

8

7

6

CHRG

VCC

FAULT

TIMER

GND

ACPR

GND GND

BAT

SHDN

PROG

NTC

1

+

NCT

-

BCD

NTC

TB3.5mm

LTC4053EDD

0.1uF

1uF

1R

2K2

1K5

GND

GND GND

1A when connected to a dedicated charger port

0A when enumerated

0A when not enumerated and not in sleep

0A when in sleep

EEPROM Setting

VBUS

Battery Options

X-Chip Pin

CBUS3

Function

BCD

Battery Charger Enable

Force Power Enable

X

NTC

JP1

NCT Available

4K32 1%

De-acticate Sleep

1-2 NCT Enabled

2-3 NCT Disabled (Default)

JP1

SIP-3

JUMPER-2mm

GND

Figure 7.4 USB Battery Charging Detection

To use the FT220X with battery charging detection the CBUS pin must be reprogrammed to allow for the

BCD Charger output to switch the external charger circuitry on. The CBUS pins are configured in the

internal MTP memory with the free utility FT_PROG. If the charging circuitry requires an active low signal

to enable it, the CBUS pin can be programmed to BCD Charger# as an alternative.

When connected to a USB compliant dedicated charging port (DCP, as opposed to a standard USB host)

the device USB signals will be shorted together and the device suspended. The BCD charger signal will

bring the LTC4053 out of suspend and allow battery charging to start. The charge current in the example

above is 1A as defined by the resistance on the PROG pin.

To calculate the equivalent resistance on the LTC4053 PROG pin select a charge current, then Res =

1500V/I_chg

For more configuration options of the LTC4053 refer to:

29

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

AN_175_Battery Charging Over USB

Note: If the FT220X is connected to a standard host port such that the device is enumerated the battery

charge detection signal is inactive as the device will not be in suspend.

30

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

8 Application Examples

The following sections illustrate possible applications of the FT220X. The illustrations have omitted pin

numbers for ease of understanding since the pins differ between the FT220XS and FT220XQ package

options.

8.1 USB to FT1248 Converter

VCCIO

10k

MIOSIO[0]

10k

FT1248 BUS

MASTER

FT220X

10k

SCLK

SS_N

MISO

Figure 8.1 Application Example showing USB to FT1248 host

The FT1248 can be used with 1-bit. 2-bit, or 4-bit wide data. The Figure 8.1 is showing 1 bit mode. By

using 4 data bits you need fewer clock cycles to get the data across.

The FT220X is the slave device and the external FPGA/MCU is the bus master. The FT220X will auto

detect the bus width from the initial command byte sent by the controller. If not using all 4 data lines the

pins may be left unterminated as an internal pull-up ensures the device detects logic 1.

Timing diagrams for 1-bit accesses can be seen in figures 8.2 and 8.3.

For further information on the mode see AN_167 FT1248 Basics from the FTDI website.

31

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

CLK

SS_n

COMMAND PHASE

WRITE DATA

BUS TURNAROUND

TXE#

CMD3

MIOSIO[0]

TXE#

0

CMD2

0

CMD1 CMD0

B7

B6

B5

B4

B3

B2

B1

B0

PULLED HIGH

MIOSIO[7:1]

RXF#

MISO

RXF#

TXE#

ACK

Figure 8.2 FT1248 1- bit write timing diagram

32

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

CLK

SS_n

COMMAND PHASE

READ DATA

BUS TURNAROUND

CMD3

MIOSIO[0]

TXE#

0

CMD2

0

CMD1 CMD0

B7

B6

B5

B4

B3

B2

B1

B0

TXE#

PULLED HIGH

MIOSIO[7:1]

RXF#

MISO

RXF#

RXF# ACK

Figure 8.3 FT1248 1- bit read timing diagram

33

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

9 Internal MTP Memory Configuration

The FT220X includes an internal MTP memory which holds the USB configuration descriptors, other

configuration data for the chip and also user data areas. Following a power-on reset or a USB reset the

FT220X will scan its internal MTP memory and read the USB configuration descriptors stored there.

In many cases, the default values programmed into the MTP memory will be suitable and no re-

programming will be necessary. The defaults can be found in Section 9.1.

The MTP memory in the FT220X can be programmed over USB if the values need to be changed for a

particular application. Further details of this are provided from section 9.2 onwards.

Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their

design can apply to FTDI for a free block of unique PIDs. See TN_100 – USB Vendor ID/Product ID

Guidelines for more details.

9.1 Default Values

The default factory programmed values of the internal MTP memory are shown in Table 9.1.

Parameter

Value

Notes

USB Vendor ID (VID)

USB Product UD (PID)

Serial Number Enabled?

0403h

6015h

Yes

FTDI default VID (hex)

FTDI default PID (hex)

A unique serial number is generated and

programmed into the MTP memory during device

final test.

Serial Number

See Note

Enabling this option will make the device pull down

on the UART interface lines when in USB suspend

mode (PWREN# is high).

Pull down I/O Pins in USB

Suspend

Disabled

FTDI

Manufacturer Name

Product Description

FT220X 4-BIT

FT1248

Max Bus Power Current

Power Source

90mA

Bus Powered

FT220X

Device Type

Returns USB 2.0 device description to the host.

Note: The device is a USB 2.0 Full Speed device

(12Mb/s) as opposed to a USB 2.0 High Speed

device (480Mb/s).

USB Version

0200

Remote Wake Up

Disabled

4mA

DBUS Drive Current

Strength

Options are 4mA, 8mA, 12mA, 16mA

Options are slow or fast

DBUS slew rate

Slow

34

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Parameter

Value

Notes

DBUS Schmitt Trigger

Enable

Normal

Options are normal or Schmitt

CBUS Drive Current

Strength

4mA

Slow

Options are 4mA, 8mA, 12mA, 16mA

Options are slow or fast

CBUS slew rate

CBUS Schmitt Trigger

Enable

Normal

Options are normal or Schmitt

Enabling this will load the VCP driver interface for

the device.

Load VCP Driver

CBUS3

Disabled

Prevents the device from entering suspend state

when unplugged.

Keep_Awake#

Table 9.1 Default Internal MTP Memory Configuration

9.2 Method of Programming the MTP Memory

9.2.1 Programming the MTP memory over USB

The MTP memory on all FT-X devices can be programmed over USB. This method is the same as for the

EEPROM on other FTDI devices such as the FT232R. No additional hardware, connections or programming

voltages are required. The device is simply connected to the host computer in the same way that it would

be for normal applications, and the FT_Prog utility is used to set the required options and program the

device.

The FT_Prog utility is provided free-of-charge from the FTDI website, and can be found at the link below.

The user guide is also available at this link.

http://www.ftdichip.com/Support/Utilities.htm#FT_Prog

Additionally, D2XX commands can be used to program the MTP memory from within user applications.

For more information on the commands available, please see the D2XX Programmers Guide below.

http://www.ftdichip.com/Support/Documents/ProgramGuides/D2XX_Programmer's_Guide(FT_000071).p

df

9.3 Memory Map

The FT-X family MTP memory has various areas which come under three main categories:



User Memory Area

Configuration Memory Area (writable)

Configuration Memory Area (non-writable)

35

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Memory Area Description

Word Address

0x3FF - 0x80

User Memory Area 2

Accessible via USB, I²C and FT1248

Configuration Memory Area

0x7E - 0x50

0x4E - 0x40

0x3E - 0x12

0x10 - 0x00

Accessible via USB, I²C and FT1248

Configuration Memory Area

Cannot be written

User Memory Area 1

Accessible via USB, I²C and FT1248

Configuration Memory Area

Accessible via USB, I²C and FT1248

Figure 9.1: Simplified memory map for the FT-X

User Memory Area

The User Memory Areas are highlighted in Green on the memory map. They can be read and written via

both USB and FT1248 on the FT220X. All locations within this range are freely programmable; no areas

have special functions and there is no checksum for the user area.

Note that the application should take into account the specification for the number of write cycles in

Section 6.4 if it will be writing to the MTP memory multiple times.

Configuration Memory Area (writable)

This area stores the configuration data for the device, including the data which is returned to the host in

the configuration descriptors (e.g. the VID, PID and string descriptions) and also values which set the

hardware configuration (the signal assigned to each CBUS pin for example).

These values can have a significant effect on the behaviour of the device. Steps must be taken to ensure

that these locations are not written to un-intentionally by an application which is intended to access only

the user area.

This area is included in a checksum which covers configuration areas of the memory, and so changing

any value can also cause this checksum to fail.

Configuration Memory Area (non-writable)

This is a reserved area and the application should not write to this area of memory. Any attempt to write

these locations will fail.

9.4 Hardware Requirements

The hardware is the same as for a typical USB-FT1248 application and no additional hardware or

programming voltages are required. For the USB connections, either a bus-powered configuration (see

Section 7.1and 7.3) or a self-powered configuration (see Section 7.2) could be used.

36

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

10 Package Parameters

The FT220X is available in two different packages. The FT220XS is the SSOP-16 option and the FT220XQ

is the QFN-16 package option. The solder reflow profile for both packages is described in Section 10.5.

10.1 SSOP-16 Package Mechanical Dimensions

Figure 10.1 SSOP-16 Package Dimensions

The FT220XS is supplied in a RoHS compliant 16 pin SSOP package. The package is lead (Pb) free and

uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC.

This package is nominally 4.90mm x 3.91mm body (4.90mm x 5.99mm including pins). The pins are on a

0.635 mm pitch. The above mechanical drawing shows the SSOP-16 package.

All dimensions are in inches.

37

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

10.2 SSOP-16 Package Markings

-B

FT220XS

Figure 10.2 SSOP-16 Package Markings

The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. This is

followed by the revision number.

The code XXXXXXXXXXXX is the manufacturing LOT code.

38

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

10.3 QFN-16 Package Mechanical Dimensions

Figure 10.3 QFN-16 Package Dimensions

The FT220XQ is supplied in a RoHS compliant leadless QFN-16 package. The package is lead (Pb) free,

and uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC.

This package is nominally 4.00mm x 4.00mm. The solder pads are on a 0.65mm pitch. The above

mechanical drawing shows the QFN-16 package. All dimensions are in millimetres.

The centre pad on the base of the FT220XQ is internally connected to GND and the PCB should not have

signal tracking on the top layer under this area. Connect to GND.

39

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

10.4 QFN-16 Package Markings

1

12

FTDI

XXXXXXXXXX

FT220XQ

YYWW-B

5

8

Figure 10.4 QFN-16 Package Markings

The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. This is

followed by the revision number.

The code XXXXXXX is the manufacturing LOT code

40

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

10.5 Solder Reflow Profile

The FT220X is supplied in Pb free 16 LD SSOP and QFN-16 packages. The recommended solder reflow

profile for both package options is shown in Figure 10.5.

t_p

T

p

Critical Zone: when

T is in the range

Ramp Up

T to T

p

L

T

L

t_L

T Max

S

Ramp

Down

T Min

S

t_S

Preheat

25

T = 25º C to T_P

Time, t (seconds)

Figure 10.5 FT220X Solder Reflow Profile

The recommended values for the solder reflow profile are detailed in Table 10.1. Values are shown for

both a completely Pb free solder process (i.e. the FT220X is used with Pb free solder), and for a non-Pb

free solder process (i.e. the FT220X is used with non-Pb free solder).

Profile Feature

Pb Free Solder Process

Non-Pb Free Solder Process

Average Ramp Up Rate (T_sto T_p)

3°C / second Max.

3°C / Second Max.

Preheat

- Temperature Min (T_sMin.)

- Temperature Max (T_sMax.)

- Time (t_sMin to t_sMax)

100°C

150°C

200°C

60 to 120 seconds

Time Maintained Above Critical Temperature

T_L:

217°C

183°C

- Temperature (T_L)

- Time (t_L)

60 to 150 seconds

Peak Temperature (T_p)

260°C

240°C

Time within 5°C of actual Peak Temperature

(t_p)

20 to 40 seconds

Ramp Down Rate

6°C / second Max.

8 minutes Max.

6°C / second Max.

6 minutes Max.

Time for T= 25°C to Peak Temperature, T_p

Table 10.1 Reflow Profile Parameter Values

41

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

11 Contact Information

Head Office – Glasgow, UK

Branch Office – Tigard, Oregon, USA

Future Technology Devices International Limited

Unit 1, 2 Seaward Place, Centurion Business Park

Glasgow G41 1HH

United Kingdom

Tel: +44 (0) 141 429 2777

Fax: +44 (0) 141 429 2758

Future Technology Devices International Limited

(USA)

7130 SW Fir Loop

Tigard, OR 97223

USA

Tel: +1 (503) 547 0988

Fax: +1 (503) 547 0987

E-mail (Sales)

E-mail (Support)

sales1@ftdichip.com

support1@ftdichip.com

E-mail (General Enquiries) admin1@ftdichip.com

E-Mail (Sales)

E-Mail (Support)

E-Mail (General Enquiries)

us.sales@ftdichip.com

us.support@ftdichip.com

us.admin@ftdichip.com

Branch Office – Taipei, Taiwan

Branch Office – Shanghai, China

Future Technology Devices International Limited

(Taiwan)

2F, No. 516, Sec. 1, NeiHu Road

Taipei 114

Taiwan , R.O.C.

Tel: +886 (0) 2 8791 3570

Fax: +886 (0) 2 8791 3576

Future Technology Devices International Limited

(China)

Room 408, 317 Xianxia Road,

Shanghai, 200051

China

Tel: +86 21 62351596

Fax: +86 21 62351595

E-mail (Sales)

tw.sales1@ftdichip.com

E-mail (Support)

E-mail (General Enquiries) tw.admin1@ftdichip.com

tw.support1@ftdichip.com

E-mail (Sales)

E-mail (Support)

E-mail (General Enquiries)

cn.sales@ftdichip.com

cn.support@ftdichip.com

cn.admin@ftdichip.com

Web Site

http://ftdichip.com

System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology

Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level

performance requirements. All application-related information in this document (including application descriptions, suggested

FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this

information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications

assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the

user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from

such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is

implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product

described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent

of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park,

Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640

42

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Appendix A – References

Useful Application Notes

http://www.ftdichip.com/Documents/AppNotes/AN232R-01_FT232RBitBangModes.pdf

http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf

http://www.ftdichip.com/Documents/AppNotes/AN_121_FTDI_Device_EEPROM_User_Area_Usage.pdf

http://www.ftdichip.com/Documents/AppNotes/AN_167_FT1248_Parallel_Serial_Interface_Basics.pdf

http://www.ftdichip.com/Documents/InstallGuides.htm

http://www.ftdichip.com/Support/Documents/TechnicalNotes/TN_100_USB_VID-PID_Guidelines.pdf

http://www.ftdichip.com/Support/Documents/AppNotes/AN_175_Battery%20Charging%20Over%20USB

%20with%20FTEX%20Devices.pdf

http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip

43

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Appendix B - List of Figures and Tables

List of Figures

Figure 2.1 FT220X Block Diagram ...................................................................................................4

Figure 3.1 QFN Schematic Symbol ..................................................................................................7

Figure 3.2 SSOP Schematic Symbol ................................................................................................9

Figure 5.1: FT1248 Basic Waveform Protocol.................................................................................. 14

Figure 5.2: FT1248 Command Structure........................................................................................ 15

Figure 5.3: FT1248 Clock Format CPHA = 1 ................................................................................... 17

Figure 5.4: FT1248 Clock Format CPHA = 1 ................................................................................... 18

Figure 7.1 Bus Powered Configuration ........................................................................................... 26

Figure 7.2 Self Powered Configuration........................................................................................... 27

Figure 7.3 Bus Powered with Power Switching Configuration ............................................................ 28

Figure 7.4 USB Battery Charging Detection.................................................................................... 29

Figure 8.1 Application Example showing USB to FT1248 host ........................................................... 31

Figure 8.2 FT1248 1- bit write timing diagram................................................................................ 32

Figure 8.3 FT1248 1- bit read timing diagram ................................................................................ 33

Figure 9.1: Simplified memory map for the FT-X ............................................................................ 36

Figure 10.1 SSOP-16 Package Dimensions..................................................................................... 37

Figure 10.2 SSOP-16 Package Markings......................................................................................... 38

Figure 10.3 QFN-16 Package Dimensions....................................................................................... 39

Figure 10.4 QFN-16 Package Markings .......................................................................................... 40

Figure 10.5 FT220X Solder Reflow Profile....................................................................................... 41

List of Tables

Table 3.1 Power and Ground ..........................................................................................................7

Table 3.2 Common Function pins....................................................................................................7

Table 3.3 FT1248 Interface and CBUS Group (see note 1)..................................................................8

Table 3.4 Power and Ground ..........................................................................................................9

Table 3.5 Common Function pins....................................................................................................9

Table 3.6 FT1248 Interface and CBUS Group (see note 1)................................................................ 10

Table 3.7 CBUS Configuration Control ........................................................................................... 11

Table 5.1: FT1248 Commands...................................................................................................... 16

Table 5.2: CPOL & CPHA Mode Numbers........................................................................................ 16

Table 5.3: 1V8 VCCIO timings...................................................................................................... 18

Table 5.4: 2V5 VCCIO timings...................................................................................................... 19

Table 5.5: 3V3 VCCIO timings...................................................................................................... 19

Table 6.1 Absolute Maximum Ratings ............................................................................................ 20

Table 6.2 ESD and Latch-Up Specifications .................................................................................... 20

Table 6.3 Operating Voltage and Current ....................................................................................... 21

Table 6.4 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins)........................................... 22

Table 6.5 I/O Pin Characteristics VCCIO = +2.5V (except USB PHY pins)........................................... 23

Table 6.6 I/O Pin Characteristics VCCIO = +1.8V (except USB PHY pins)........................................... 24

44

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Table 6.7 USB I/O Pin (USBDP, USBDM) Characteristics .................................................................. 25

Table 6.8 MTP Memory Characteristics........................................................................................... 25

Table 6.9 Internal Clock Characteristics......................................................................................... 25

Table 9.1 Default Internal MTP Memory Configuration ..................................................................... 35

Table 10.1 Reflow Profile Parameter Values.................................................................................... 41

45

FT220X USB 4-BIT SPI/FT1248 IC Datasheet

Version 1.3

Document No.: FT_000629 Clearance No.: FTDI# 262

Appendix C - Revision History

Document Title:

USB 4-BIT SPI/FT1248 IC FT220X

Document Reference No.:

Clearance No.:

FT_000629

FTDI# 262

Product Page:

http://www.ftdichip.com/FT-X.htm

Send Feedback

Document Feedback:

Version 1.0

Version 1.1

Initial Release

Added USB compliance in section 1.3

8^thFebruary 2012

17^thApril 2012

Clarified MTP Reliability in table 6.8

Edited EEPROM Table 9.1 changed Load VCP

Driver to Disabled and edited Product Description

Version 1.2

Removed references to LED signals on the CBUS pins as

these are not available on the FT220X.

Removed section 8.2 showing connection of the Tx/Rx LEDs.

Updated TID

14th Feb 2013

Updated US address

Added clarification on front page about 5V tolerant

Version 1.3

Removed references to MTP programming over FT1248 and

clarified package dimensions.

10th Feb 2014

46


型号：	FT220X
厂家：	FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD.
描述：	FT220X USB 4-BIT SPI/FT1248 IC Datasheet Version 1.3
文件：	总46页 (文件大小：947K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

FT220X [FTDI]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E