FTR-B3GA009Z-B10 [FUJITSU]
Power/Signal Relay, POWER/SIGNAL RELAY;型号: | FTR-B3GA009Z-B10 |
厂家: | FUJITSU |
描述: | Power/Signal Relay, POWER/SIGNAL RELAY 光电二极管 继电器 |
文件: | 总10页 (文件大小:763K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ULTRA MINIATURE RELAY
2 POLES - 2 A (Low Profile Signal Relay)
FTR-B3 Series
n FEATURES
l DPDT 2C
l Ultra miniature low profile relay with high heat resistant material
l Height: 5.45mm, Weight: 0.85g, Mounting space: 87mm2
l Adopted superior contact spring for high frequency characteristic
l Comply with Telcordia / FCC standard
- Isolation distance: min. 1.6mm
- Dielectric strength between coil and contact: 1500VAC
- Surge strength: 2500V
l Low power: Non-latching: 140mW (230mW at 24V)
Latching: 100mW (120mW at 24V)
l High reliable bifurcated gold overlay silver contact
l UL, CSA recognized. Confirms to IEC 60950, UL1950,
EN60950. Spacing & high breakdown voltage (basic
insulation, 150 working volts, pollution degree 2)
l RoHS compliant.
Please see page 9 for more information
n PARTNUMBER INFORMATION
FTR-B3
(a)
G
B
012
Z
-
B
10
[Example]
(b) (c) (d) (e)
(f) (g)
(a)
(b)
Relay type
FTR-B3 : FTR-B3-Series
Terminal type
C
G
S
: Through hole
: Surface mount
: Surface mount, space saving
(c)
(d)
(e)
Coil type
A
B
: Standard type
: Latching type (1 coil)
Coil rated voltage
Contact material
012
: 1.5.....24 VDC
Coil rating table at page 3
Z
P
: Gold overlay silver nickel
: Gold overlay silver palladium
(f)
Relay enclosing direction *1
Number of relays per reel *2
B
: Standard enclosing direction
: 1,000 (standard)
(g)
10
Remarks: Actual marking on relay would not carry code FTR and be as below:
Ordering code: FTR-B3GB012Z-B10 Actual marking: B3GB012Z
* 1 Only surface mount types (G and S) are applicable
* 2 All relays are packaged in tubes unless part number ends with -B10 (50 relays per tube).
1
FTR-B3 SERIES
n SPECIFICATION
Item
Standard type
FTR-B3 ( ) A
2 form C
Latching type
FTR-B3 ( ) B
Contact Data Configuration
Construction
Bifurcated contacts (cross-bar)
Gold overlay silver nickel / Gold overlay silver
palladium
Material
Resistance (initial)
Max. 75 mΩ at 1 A, 6 VDC
30VDC, 1A / 125VAC, 0.3A
2A
Contact rating (resistive)
Max. carrying current
Max. switching voltage
Max. switching power
Min. switching load *
250 VAC / 220VDC
62.5VA / 30W
0.01mA, 10mVDC
Life
Min. 50 x 106 operations
(at 3Hz)
Min. 20 x 106 operations
(at 3Hz)
Mechanical
Electrical
Min. 100 x 103 operations at 1A 30VDC (at 0.5Hz)
Min. 100 x 103 operations at 0.3A 125VDC (at 0.5Hz)
Coil Data
Rated power
140mW - 230mW
100mW - 120mW
57mW - 68mW
Operate power
80mW - 130mW
Operating temperature range
-40 °C to +85 °C (no frost)
Max. 3 ms (without bounce)
Max. 3 ms (without bounce)
Min. 1,000MΩ at 500VDC
1,000VAC (50/60Hz) 1min
1,500VAC (50/60Hz) 1min
Timing Data Operate (at nominal voltage)
Release (at nominal voltage)
Insulation
Resistance (initial)
Dielectric strength
Surge strength
Clearance
Open contacts
Contacts to coil
Adjacent contacts 1,000VAC (50/60Hz) 1min.
Coil to contacts 2,500V, 2 x 10µs standard wave
Adjacent contacts 1.0 mm
Open contacts
0.28 mm
1.0 mm
Coil and contacts
Adjacent contacts 1.0 mm
Creepage
Open contacts
Coil and contacts
Misoperation
Endurance
0.28 mm
1.60 mm
Other
10 to 55Hz double amplitude 3.3mm
10 to 55Hz double amplitude 5.0mm
750m/s²
Vibration resistance
Misoperation
Endurance
Shock
1,000m/s²
Weight
Approximately 0.8 g
* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual
load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.
2
FTR-B3 SERIES
n COIL RATING
Standard type
Rated Coil
Voltage
(VDC)
Must Operate
Voltage
Must Release
Voltage
Coil
Code
Coil Resistance
+/- 10% (Ohm)
Max. Coil Voltage
(VDC)
Rated Power
(mW)
(VDC) *
(VDC) *
1.5
003
4.5
1.5
3
16.1
64.3
145
1.13
2.25
3.38
4.5
0.15
0.3
3.53
7.05
4.5
6
0.45
0.6
10.58
14.10
21.15
28.20
56.40
140
230
006
009
012
024
257
9
579
6.75
9
0.9
12
24
1,028
2,504
1.2
18
2.4
Latching type (1 coil)
Rated Coil
Voltage
(VDC)
Must Operate
Voltage
Must Release
Voltage
Coil
Code
Coil Resistance
+/- 10% (Ohm)
Max. Coil Voltage
(VDC)
Rated Power
(mW)
(VDC) *
(VDC) *
1.5
003
4.5
1.5
3
22.5
90
1.13
2.25
3.38
4.5
-0.13
-2.25
-3.38
-4.5
-6.75
-9
3.53
7.05
4.5
6
203
10.58
14.10
21.15
28.20
56.40
100
120
006
009
012
024
360
9
810
6.75
9
12
24
1,440
4,800
18
-18
Note: All values in the table are valid for 20°C and zero contact current.
* Specified operate values are valid for pulse wave voltage.
n SAFETY STANDARDS
Type
Compliance
Contact rating
UL
UL 508
Flammability: UL 94-V0 (plastics)
0.5A, 125VAC (resistive)
1A, 30VDC (resistive)
0.3A, 110VDC (resistive)
2A, 30VDC (resistive)
E 63615
CSA
C22.2 No. 14
LR 40304-58
3
FTR-B3 SERIES
n CHARACTERISTIC DATA
l
Standard type
4
FTR-B3 SERIES
l
Latching type
5
FTR-B3 SERIES
6
FTR-B3 SERIES
n DIMENSIONS
FTR-B3C - Through hole type
l
PC board mounting
hole layout
l
Schematics
(BOTTOM VIEW)
l
Dimensions
(BOTTOM VIEW)
FTR-B3G - Surface mount type
l
Schematics
(TOP VIEW)
l
PC board mounting
pad layout
l
Dimensions
(TOP VIEW)
FTR-B3S - Space saving type
l
PC board mounting
pad layout
l
Schematics
(TOP VIEW)
l
Dimensions
(TOP VIEW)
Unit: mm
7
FTR-B3 SERIES
n RECOMMENDED SOLDERING CONDITIONS FOR SMT (SEE PAGE 9)
(TEMPERATURE PROFILE)
Notes:
1. Temperature profiles on page 9 show the temperature of PC board surface.
2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board
surfaces vary according to the size of PC board, status of parts mounting and heating method.
n PRECAUTIONS
- For details on general precautions, refer to the section on technical descriptions.
- Since this is a polarized relay, follow the instructions of the internal wiring diagram for the ± connections of the coil.
- Note that the terminal layout and internal wiring of the surface mount relay are a top view.
- SMT versions of the FTR-B3 relays have moisture sensitivity level 3, acc. JEDEC-J-STD-020D
- SMT versions of the FTR-B3 relays will be shipped in "dry pack". Relays have an "out bag" storage time of 192h.
n PACKAGING SPECIFICATIONS
l
Packaging method
l
Packaging orientation code: B
- Packaging standard: JIS C 0806
- Taping type: TB 1612
- Reel type: R16D
- Quantity of 1 reel: 1000 pieces
l
Tape dimensions
l
Reel dimensions
Unit: mm
Note:
Relays are sold in 1000 pieces per box. Minimum order quantity is 1000 pieces
for tube and tape & reel packing.
8
FTR-B3SERIES
RoHS Compliance and Lead Free Information
1. General Information
l
l
l
l
All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including
amendments.
Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005.
(Amendment to Directive 2002/95/EC)
All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes
at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf
Lead free solder plating on relay terminals is Sn-3.0Cu-Ni for FTR-B3 and FTR-B4 series relays.
This material has been verified to be compatible with PbSn assembly process.
2. Recommended Lead Free Solder Profile
l
Recommended solder Sn-3.0Ag-0.5Cu or Sn-3.0 Cu-Ni (only FTR-B3 and FTR-B4)
Flow Solder condition:
Pre-heating:
Soldering:
maximum 120˚C
dip within 5 sec. at
260˚C solder bath
Solder by Soldering Iron:
Soldering Iron
Temperature:
Duration:
maximum 360˚C
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3. Moisture Sensitivity
l
Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l
Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
9
FTR-B3 SERIES
Fujitsu Components International Headquarter Offices
Japan
Europe
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (81-3) 5449-7010
Tel: (31-23) 5560910
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: emea.fujitsu.com/components/
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
#01-01 Citilink Warehouse Complex
Singapore 118529
Fax: (1-408) 745-4970
Tel: (65) 6375-8560
Email: components@us.fujitsu.com
Web: http://us.fujitsu.com/components
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
Web: http://www.fujitsu.com/sg/services/micro/components/
©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its
employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use,
with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. December 06, 2011
10
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明