10DAW4_2403S1.5 [GAPTEC]

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated;


型号：	10DAW4_2403S1.5
厂家：	GAPTEC
描述：	10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated
文件：	总5页 (文件大小：1436K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

10DAW4_1.5 Series

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated

DC-DC Converter

10 Watt

The 10DAW4 series are isolated 10W DC-DC products with 4:1 input

voltage. They feature efﬁciency up to 88%, 1500VDC isolation,

operating temperature of -40°C~+85°C, output over-voltage protection,

short-circuit protection and EMI meets CISPR22/EN55022 CLASS A.

4:1 wide input voltage range

Efﬁciency up to 88%

1.5KVDC isolation

Short circuit protection (SCP)

Output over voltage protection

Operating Temperature range:

-40°C ~ +85°C

Six-sided metal shield

Industry standard pinout

Low ripple & noise

Meet CISPR22/EN55022

CLASS A

Meet EN60950

Inverse polarity protection for

chassis mounting

Widely applied in battery power supplies, industrial control, electricity,

instruments, communication ﬁelds. An extension package with chassis

mounting also enables them with reverse voltage protection.

Common speciﬁcations

Short circuit protection:

Cooling:

Output speciﬁcations

Continuous, automatic recovery

Free air convection

Item

Test condition

Min

Typ

Max

Units

Output voltage

accuracy

Refer to recommended

circuit

Operation temperature range (power

derating above 71°C):

-40°C~+85°C

Output voltage

balance

Dual outputs, balanced

loads

0.5

1.5

Storage temperature range:

Lead temperature range:

No-load power consumption:

Switching freuquency (PWM mode):

Storage humidity range:

Vibration:

-55°C ~+125°C

Line regulation

Full load, Input voltage

from low to high

• Main side

300°C MAX, 1.5mm from case for 10 sec

500mW TYP

0.2

0.5

• Secondary side

50KHz TYP

Load regulation

Cross regulation

5% to 100% load

< 95%

Dual output, main

output 50% load,

secondary output from

10% to 100% load

10-55Hz,10G,30 Min. along X, Y and Z

Aluminium alloy

Case material:

MTBF (MIL-HDBK-217F@25°C):

Weight:

>1,000,000 hours

Temperature

coefﬁcient

100% load

0.03 %/°C

22g / 44g (chassis-mounting)

Ripple&Noise*

20MHz Bandwidth

mVp-p

µs

Isolation speciﬁcations

Transient recovery 25% load step change

time

300

500

Item

Test condition

Min

Typ

Max

Units

VDC

Transient response 25% load step change

deviation

Isolation voltage

Tested for 1 minute

and 1mA max

1500

Output over voltage Input voltage range

protection

110

120

140

Isolation resistance

Isolation capacitance

Test at 500VDC

1000

MΩ

Input/Output,

100KHz/0.1V

1000

* Ripple and noise tested by “parallel cable” method. See detailed operation

instructions at DC-DC application notes.

Model selection:

WCTV_xxyyN##

W= Watt; C= Case; T= Type; V= Voltage Variation;

Input speciﬁcations

xx= Vin; yy= Vout; N= Numbers of Output; ##= Isolation (kVDC)

Item

Test condition

Min Typ

Max

Units

Input ﬁlter

Hot plug

Example:

10DAW4_2405S1.5

10=10Watt; D= DIP; A=series; W4= wide input (4:1) 9-36Vin; 5Vout;

S=single output; 1.5=1500VDC

Unavailable

Input current

(full load/no load)

• 24VDC input

• 48VDC input

508/12 521/21 mA

254/6

261/11 mA

Reﬂected ripple current • 24VDC input

• 48VDC input

Note:

1. Min. load shouldn‘t be less than 5%, otherwise ripple may be increased

dramatically, If the product operates under min. load, it may not be guaranteed

to meet all speciﬁcations listed. Operation under minimum load will not damage

the converter.

2. Recommended Dual output models unbalanced load is ≤ 5%, If the product

operates > 5%, it may not be guaranteed to meet all speciﬁcations listed.

Please contact our technical support for more details.

3. Max. Capacitive Load is tested at input voltage range and full load.

4. All speciﬁcations measured at Ta=25°C, humidity<75%, nominal input voltage

and rated output load unless otherwise speciﬁed.

5. In this datasheet, all test methods are based on our corporate standards.

6. All characteristics are for listed models, and non-standard models may perform

differently. Please contact our technical support for more details.

7. Please contact our technical support for any speciﬁc requirement.

Input impulse voltage

(1sec. max)

• 24VDC input

• 48VDC input

-0.7

100

VDC

Starting voltage

• 24VDC input

• 48VDC input

VDC

Ctrl⁽¹⁾

• Models ON

• Models OFF

Ctrl pin ﬂoating or connect to TTL

high level (3.5-12VDC)

Ctrl pin connected to GND or low

level (0-1.2VDC)

• Input current

(models OFF)

1. The CTRL pin voltage is referenced to GND.

Page 1 of 5

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

10DAW4_1.5 – Rev. 2016-1.1

Speciﬁcations subject to change without notice.

10DAW4_1.5 Series

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated

DC-DC Converter

EMC speciﬁcations

EMI

CISPR22/EN55022

CLASS A (bare component)

CLASS B (see EMC solution-recommended circuit, 2 )

EMI

CISPR22/EN55022

CLASS A (bare component)

CLASS B (see EMC solution-recommended circuit, 2 )

EMS

ESD

IEC/EN61000-4-2

IEC/EN61000-4-3

IEC/EN61000-4-4

IEC/EN61000-4-5

IEC/EN61000-4-6

IEC/EN61000-4-29

Contact 4KV

10V/m

perf. Criteria B

perf. Criteria A

EFT

Surge

2KV

perf. Criteria B (see EMC solution-recommended circuit, 1 )

perf. Criteria A

2KV

3 Vr.m.s

0%-70%

Voltage dips, short and

interruptions immunity

perf. Criteria B

Part Number

Input Voltage [VDC]

Output Voltage [VDC]

Output current [mA]

Capacitive load ³⁾[µF, Max.]

Efﬁciency ⁴⁾[%, Typ.]

Nominal

Range

Max ²⁾

Max

2400

2000

833

Min

120

100

10DAW4_2403S1.5

10DAW4_2405S1.5

10DAW4_2412S1.5

10DAW4_2415S1.5

10DAW4_2424S1.5

10DAW4_4803S1.5

10DAW4_4805S1.5

10DAW4_4812S1.5

10DAW4_4815S1.5

10DAW4_4824S1.5

10DAW4_2405D1.5

10DAW4_2412D1.5

10DAW4_2415D1.5

10DAW4_4805D1.5

10DAW4_4812D1.5

10DAW4_4815D1.5

9-36

3.3

2200

470

330

100

2200

470

330

100

680

220

100

680

220

100

9-36

3.3

9-36

667

9-36

416

18-72

9-36

2400

2000

833

120

100

667

416

1000

416

9-36

333

18-72

8-72

1000

416

333

1) Sufﬁx „X“ means the model with CTRL pin, for example 10DAW4_2403S1.5/X

2) Absolute maximum rating without damage on the converter;

3) For the dual output modules, the capacitive loads of positive and negative outputs are the same.

4) The efﬁciency of products with chassis mounting is 2% lower than the DIP package ones due to the reverse voltage protection;

Typical characteristics

Page 2 of 5

GAPTEC-Electronic GmbH & Co. KG

10DAW4_1.5 – Rev. 2016-1.1

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

10DAW4_1.5 Series

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated

DC-DC Converter

Efﬁciency

10DAW4_4805D1.5

10DAW4_2405S1.5

Recommended circuit

All the DC/DC converters of this series are tested according to the recom-

mended circuit (see Fig. 1) before delivery.

If a further decrease of the input and output ripple is required, properly

increase the input & output of additional capacitors Cin and Cout or

select capacitors of low equivalent impedance and ensure the capaci-

tance should be lower than the max. capacitive load of the product.

Cin

Cout

10µF ~ 47µF

10µF

Figure 1

Page 3 of 5

10DAW4_1.5 – Rev. 2016-1.1

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

10DAW4_1.5 Series

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated

DC-DC Converter

EMC solution-recommended circuit

Parameter description:

Model

FUSE

MOV

Vin: 24V

Vin: 48V

Choose according to actual input current

S14K35

330µF/50V

1µF/50V

S14K60

330µF/100V

1µF/100V

Refer to the Cout in recommended circuit

LDM1

CY1

CY2

4.7µH

Note:

Part 1 is for EMS test, part 2 is for EMI ﬁltering

Choose according to requirements.

1nF/2KV

EMC recommended circuit PCB layout

It is not allowed to connect modules output in parallel to enlarge the power.

Mechanical dimensions and footprint

Note:

Unit: mm[inch]

Pin diameter tolerances: 0.10mm [ 0.004inch]

General tolerances: 0.50mm [ 0.050inch]

Page 4 of 5

GAPTEC-Electronic GmbH & Co. KG

10DAW4_1.5 – Rev. 2016-1.1

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

10DAW4_1.5 Series

10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated

DC-DC Converter

Chassis mounting

10DAW4_D1.5

10DAW4_S1.5

Page 5 of 5

10DAW4_1.5 – Rev. 2016-1.1

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

相关型号：