15DMWE4_4824D1.5 [GAPTEC]
15W - Single Output - Wide Input - Isolated & Regulated;型号: | 15DMWE4_4824D1.5 |
厂家: | GAPTEC |
描述: | 15W - Single Output - Wide Input - Isolated & Regulated |
文件: | 总5页 (文件大小:2798K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
15DMWE4_D1.5 Series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
DC-DC Converter
15 Watt
Wide 4:1 input voltage range
High efficiency up to 90%
Short circuit protection (SCP)
Isolation voltage: 1.5K VDC
Over-current, over-voltage,
under-voltage protection
RoHS compliant
Operating temperature range:
The 15DMWE4_1.5 series are isolated 15W DC/DC converters with 2:1 in-
put voltage. They feature efficiency up to 91%, 1500VDC isolation, ope-
rating temperature of -40°C to +105°C, input under-voltage protection,
output over-voltage, output over-current, output short circuit protec-
tion and EMI meets CISPR32/EN55032 CLASS A.
-40°C to +105°C
Meet CISPR32/EN55032 CLASS
A, no external components
International standard pin-out
Wiring and rail mounting
products featuring anti-
reverse connection for input
Meets EN62368 standards
(pending)
They are widely applied in industrial control, electric power, instru-
ments and communication fields. Extension packages with wiring
mounting and rail mounting also enable them with reverse voltage pro-
tection.
Common specifications
Short circuit protection:
Cooling:
Input specifications
Continuous, self-recovery
Free air convection
Item
Test condition
Min
Typ
Max
Units
Input current*
(full load/no load)
• 24VDC
• 48VDC
958/10
969/5
-/20
-/11
mA
mA
Operation temperature range:
-40°C~+105°C (see temperature
derating curve)
Reflected ripple
current
Nominal input
series
30
mA
Storage temperature range:
Storage humidity range:
Lead temperature:
Vibration:
-55°C~+125°C
Surge voltage
• 24VDC input
• 48VDC input
-0.7
-0.7
50
100
VDC
VDC
95% MAX
300°C MAX, 1.5mm from case for 10 sec
10-150Hz, 5G, 0.75mm. along X, Y and Z
Aluminium alloy
Starting voltage
• 24VDC input
• 48VDC input
9
18
VDC
VDC
Input under-
voltage protection
• 24VDC input
• 48VDC input
5.5
12
6.5
15.5
VDC
VDC
Case material:
MTBF (MIL-HDBK-217F @25°C):
Weight:
1,000,000 hours
Starting time
Input filter
Hot plug
10
ms
15g / 35g (wiring) / 55g (rail)
Pi Type
Unavailable
Output specifications
Switching frequency PWM mode
270
KHz
Item
Test condition
Min
Typ
1
Max
3
Units
%
Ctrl
• Module switch on Ctrl suspended or connected to TTL
high level (3.5-12VDC)
Voltage accuracy* 5%-100% load
(The voltage of Ctrl • Module switch off Ctrl pin connected to GND or low
pin is relative to
input pin GND)
Line regulation
Full load, low to high
• positive output
• negative output
level (0-1.2VDC)
2
0.2
0.4
0.5
1
%
%
• Input current
when switched off
7
mA
Load regulation
Cross regulation
5% load to full load
0.5
1
%
%
* Nominal input seriesꢀ nominal input voltage
Dual output, main
circuit with 50% load,
auxiliary circuit with
10%-100% load
5
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
VDC
VDC
Transient recovery 25% load step change
time
300
500
µs
Isolation voltage
Isolation voltage
Input to output
1500
1000
Transient respon-
se deviation
25% load step change
• 5V output
• Others
Input to output,
respectively on the
shell
3
3
8
5
%
%
Temperature drift
Ripple and noise*
Full load
0.03 %/°C
Isolation resistance
Test at 500VDC
1000
MΩ
pF
20MHz Bandwidth
Input voltage range
100
200
200
mVp-p
%Io
Isolation capacitance
Input-output,
100KHz/0.1V
2000
Over current
protection
110
110
270
Over voltage
protection
Input voltage range
160
%Vo
Example:
15DMWE4_2415D1.5
15= 15Watt; D= DIP; M= series; W4= wide input (4:1); E= cost
effective; 9-36Vin; 15Vout; D= dual output; 1.5= 1500VDC
*
At 0%-5% load, the Max. output voltage accuracy converter is 5%.
** 0%-5% load ripple&noise is no more than 5%Vo.
Ripple and noise are measured by “parallel cable” method.
Page 1 of 5
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMWE4_D1.5 – Rev. 2019-1.1
Specifications subject to change without notice.
15DMWE4_D1.5 Series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
EMC specifications
EMI
CE
CISPR32/EN55032
CISPR32/EN55032
CLASS A (without external components)
CLASS B (see EMC solution recommended circuit, ②)
EMI
RE
CLASS A (without external components)
CLASS B (see EMC solution recommended circuit, ②)
EMS
EMS
EMS
EMS
EMS
ESD
RS
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-5
IEC/EN61000-4-6
Contact 4KV
perf. Criteria B
perf. Criteria A
perf. Criteria B
perf. Criteria B
perf. Criteria A
10V/m
EFT
Surge
CS
2KV (see EMC solution recommended circuit, ①)
line to line 2KV (see EMC solution recommended circuit, ①)
3 Vr.m.s
Part Number
Input Voltage [VDC]
Output Voltage [VDC]
Output Current [mA]
Efficiency [%, Typ.]***
Capacitive load [µF, Max.]
Nominal
Range*
Max**
40
Full load
1500
625
15DMWE4_2405D1.5
15DMWE4_2412D1.5
15DMWE4_2415D1.5
15DMWE4_2424D1.5
15DMWE4_4805D1.5
15DMWE4_4812D1.5
15DMWE4_4815D1.5
15DMWE4_4824D1.5
24
24
24
24
48
48
48
48
9-36
5
12
15
24
5
87
90
90
89
86
90
90
90
1500
470
330
9-36
40
9-36
40
500
9-36
40
312
200
1500
470
330
18-75
18-75
18-75
18-75
80
1500
625
80
12
15
24
80
500
80
312
200
Add suffix CM for chassis mounting, f.ex. 15DMWE4_1203D1.5CM, or suffix RM for rail mounting, f.ex. 15DMWE4_1203D1.5RM.
The minimum input voltage and starting voltage of wring or rail models are 1VDC higher than those of DIP package due to input reverse polarity protection function.
*
** Absolute maximum rating without damage on the converter, but it isn‘t recommended.
*** Efficiency is measured in nominal input voltage and rated output load; for wiring and rail mounting models, due to input reverse polarity protection, a minimum
efficiency greater than Min.-2 is qualified.
Typical characteristics
Page 2 of 5
15DMWE4_D1.5 – Rev. 2019-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMWE4_D1.5 Series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Efficiency
15DMWE4_2405D1.5
15DMWE4_2405D1.5
15DMWE4_2415D1.5
15DMWE4_2415D1.5
Typical application
All the DC/DC converters of this series are tested according to the recommended
circuit before delivery.
If it is required to further reduce input and output ripple, properly increase the
input & output of additional capacitors Cin and Cout or select capacitors of low
equivalent impedance provided that the capacitance is no larger than the max.
capacitive load of the product.
EMC solution-recommended circuit
Refer to the Cout in typical application
It is not allowed to connect modules output in parallel to enlarge the power.
Page 3 of 5
15DMWE4_D1.5 – Rev. 2019-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMWE4_D1.5 Series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Mechanical dimensions and footprint
Wiring mounting
Page 4 of 5
15DMWE4_D1.5 – Rev. 2019-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMWE4_D1.5 Series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Rail mounting
Note:
1. Only typical model listed. Non-standard models will be different from the above,
please contact us for more details.
2. All specifications are measured at TA=25°C, humidity<75%, nominal input volta-
ge and rated output load unless otherwise specified.
3. In this datasheet, all the test methods of indications are based on corporate
standards.
Page 5 of 5
15DMWE4_D1.5 – Rev. 2019-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明