1S7B_1205S6UP [GAPTEC]
1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated;
| 型号： | 1S7B_1205S6UP |
| 厂家： | 
GAPTEC |
| 描述： | 1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated |
| 文件： | 总4页 (文件大小：1517K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1S7B_6UP series
1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated
DC-DC Converter
1 Watt
The 1S7B_6UP series are specially designed for applications where an isolated
voltage is required in a distributed power supply system. They are suitable for:
pure digital circuits, low frequency analog circuits, relay-driven circuits and data
switching circuits.
High efficiency up to 80%
4200VAC/6000VDC isolation
SIP package
Operating temperature:
-40°C up to +85°C
RoHS compliance
Reinforced insulation
The patient leakage current:
Max 2μA
Short circuit protection
EN60601-1, ANSI/AAMI
ES60601-1 approved
(1 x MOPP/2 x MOOP)
Meets EN62368
These products apply to:
1) Where the voltage of the input power supply is fixed (voltage
variation ≤ 10%)
International standard pinout
2) Where isolation is necessary between input and output
(isolation voltage ≤4200VAC or 6000VDC)
3) Where do not has high requirement of line regulation and the ripple & noise
of the output voltage; such as: Medical collection and isolation, High voltage
collection circuit, IGBT-driven circuits, etc.
UL-60601-1 (E486991)
Common specifications
Short circuit protection:
Operation temperature range:
Storage temperature range:
Pin Soldering Resistance Temp
Storage humidity range:
MTBF (MIL-HDBK-217F@25°C):
Case Temperature Rise (Ta=25°C)
Case material:
Output specifications
Continuous, self-recovery
-40°C – +105°C
Item
Test condition
Min Typ
Max Units
Voltage accuracy See output regulation curve (Fig. 1)
-55°C – +125°C
Line regulation
Load regulation
For Vin change of 1%
1.2
%
300°C MAX, 1.5mm from case for 10 sec
< 95% (Non-condensing)
>3,500,000 hours
10% to 100% load
• 3.3VDC output
• 5VDC output
15
12
8
%
%
%
%
%
%
• 7.2/9VDC output
• 12VDC output
• 15VDC output
• 24VDC output
7
25°C
6
5
Black plastic; flame-retardant and
heat-resistant (UL94-V0)
Temperature
coefficient
full load
0.03
%/°C
Weight:
4.2g
Ripple & Noise*
20MHz Bandwidth
• 3.3/5/7.2/9/12VDC output
• 15/24VDC output
Dimensions
Cooling:
19.50 x 9.80 x 12.50 mm
Free air convection
100
150
150
120
mVp-p
mVp-p
Switching
frequency
Full load, nominal input
50
KHz
Input specifications
* Note:* The “parallel cable” method is used for Ripple and Noise test, please
refer to DC-DC Converter Application Notes for specific information.
Item
Test condition
Min Typ
Max
Units
Input current
(no-load/full load)
• 5VDC input
3.3VDC output
5/7.2VDC output
9/12/15VDC output
24VDC output
• 12VDC input
5/7.2VDC output
9/15VDC output
12VDC output
• 15VDC input
5VDC output
278/30 295/-
256/30 271/-
253/30 267/-
250/30 264/-
mA
mA
mA
mA
Isolation specifications
Item
Test condition
Min
Typ
10
Max
Units
VDC
Isolation voltage
Tested for 1 minute and 6000
1mA max
104/20 110/-
102/20 107/-
103/20 109/-
mA
mA
mA
Isolation resistance
Test at 500VDC
1000
MΩ
pF
Isolation capacitance Input/Output,
100KHz/0.1V
8
2
82/15
81/15
88/-
87/-
mA
mA
15VDC output
• 24VDC input
3.3VDC output
5/12/15VDC output
Patient leakage
current*:
250VAC, 50/60Hz
µA
58/10
52/10
62/-
55/-
mA
mA
Reflected Ripple
Current*
• 5VDC input
15
5
mA
mA
• 12/15/24VDC input
Example:
1S7B_0505D6UP
Input surge
voltage
(1sec. max.)
• 5VDC input
• 12VDC input
• 15VDC input
• 24VDC input
-0.7
-0.7
-0.7
-0.7
9
VDC
VDC
VDC
VDC
1 = 1Watt; S7 = SIP7; B = Pinning; 05 = 5Vin; 05 = 5Vout;
D = Dual Output; 6 = 6kVDC isolation; U = Unregulated Output;
P = Short circuit protection
18
21
30
Input filter
Hot plug
Capacitor
Unavailable
EMC specifications
Note: * Refer to DC-DC Converter Application Notes for detailed description of
reflected ripple current test method.
EMI
EMI
EMS
CE
CISPR32/EN55032 CLASS B
(see EMC recommended circuit)
RE
CISPR32/EN55032 CLASS B
(see EMC for recommended circuit)
ESD
IEC/EN61000-4-2 Contact 8kV perf. Criteria B
Page 1 of 4
1S7B_6UP – Rev. 2020-2.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
1S7B_6UP series
1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated
Part Number
Input Voltage
[Nominal (Range), V]
Output Voltage [VDC]
Output current [mA]
Max. capacitive load
[μF]
Efficiency [%, typ]
1S7B_0503S6UP
1S7B_0505S6UP
1S7B_0509S6UP
1S7B_0512S6UP
1S7B_0515S6UP
1S7B_0524S6UP
1S7B_1205S6UP
1S7B_1207S6UP
1S7B_1209S6UP
1S7B_1212S6UP
1S7B_1215S6UP
1S7B_1505S6UP
1S7B_2403S6UP
1S7B_2405S6UP
1S7B_2412S6UP
1S7B_2415S6UP
5 (4.5-5.5)
5 (4.5-5.5)
3.3
5
303
200
111
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
72
78
79
79
79
80
80
80
82
81
5 (4.5-5.5)
9
5 (4.5-5.5)
12
15
24
5
84
5 (4.5-5.5)
67
5 (4.5-5.5)
42
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
15 (13.5-16.5)
24 (21.6- 26.4)
24 (21.6- 26.4)
24 (21.6- 26.4)
24 (21.6- 26.4)
200
139
111
7.2
9
12
15
5
84
67
82
80
72
80
80
80
200
303
200
84
3.3
5
12
15
67
Part Number
Input Voltage
[Nominal (Range), V]
Output Voltage [VDC]
Output current [mA]
Max. capacitive load
[μF]
Efficiency [%, typ]
1S7B_0505D6UP
1S7B_0507D6UP
1S7B_0509D6UP
1S7B_0512D6UP
1S7B_0515D6UP
1S7B_1205D6UP
1S7B_1207D6UP
1S7B_1209D6UP
1S7B_1212D6UP
1S7B_1215D6UP
1S7B_1515D6UP
1S7B_1505D6UP
5 (4.5-5.5)
5 (4.5-5.5)
5
7.2
9
100
70
100
100
100
100
100
100
100
100
100
100
100
100
78
78
79
79
79
77
77
80
73
75
81
5 (4.5-5.5)
56
5 (4.5-5.5)
12
15
5
42
5 (4.5-5.5)
33
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
12 (10.8-13.2)
15 (13.5-16.5)
15 (13.5-16.5)
100
70
7.2
9
56
12
15
15
5
42
34
33
100
80
Typical characteristics
Page 2 of 4
1S7B_6UP – Rev. 2020-2.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
1S7B_6UP series
1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated
Efficiency curves
1S7B_0505S6U
1S7B_0505D6U
1S7B_0505S6U
1S7B_0505D6U
Typical application
If it is required to further reduce input and output ripple, a filter capa-
citor can be connected to the input and output terminals, see Fig. 1.
Moreover, choosing suitable filter capacitor is very important, start-up
problems may be caused by too large capacitance. To ensured the mo-
dules running well, the recommended capacitive load values as shown
in Table 1.
The simplest device for output voltage regulation, over-voltage and
over-current protection is a linear voltage regulator with overheat pro-
tection that is connected to the input or output end in series (see Fig.
2).
Recommended capacitive load value table:
Vin
(VDC)
Cin
(μF)
Single
Vout
(VDC)
Cout
(μF)
Dual
Vout
Cout
(μF)
(VDC)
3.3/5
12/15
24
10
4.7
2.2
3.3/5
12
10
2.2
1
5
9
4.7
2.2
1
15
12/ 15
It’s not recommended to connect any external capacitor in the
application field with less than 0.5 watt output.
Table 1
Fig. 1
Fig. 2
Page 3 of 4
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
1S7B_6UP – Rev. 2020-2.1
Specifications subject to change without notice.
1S7B_6UP series
1W - Single/Dual Output DC-DC Converter - Fixed Input - Isolated & Unregulated
EMC typical recommended circuit (CLASS B)
Recommended typical circuit parameters:
Input voltage
3.3/5/12/15/24
4.7µF/50V
EMI
EMI
C1, C2
C3
Refer to the Cout in Typical
application, fig. 1
EMI
LDM
6.8µH
Output load requirements
In order to ensure the converter can work reliably with high efficiency,
the minimum load should not less than 10% rated load when it is used.
If the needed power is indeed small, please parallel a resistor on the
output side (The sum of the efficient power and resistor consumption
power is not less than 10%).
Mechanical dimensions
Recommended footprint
Note:
1. Operation under minimum load will not damage the converter; however, they
may not meet all specifications.
2. Max. Capacitive Load is tested at nominal input voltage and full load.
3. Unless otherwise noted, All specifications are measured at Ta = 25°C,
humidity <75%, nominal input voltage and rated output load.
4. In this datasheet, all test methods are based on our corporate standards.
5. All characteristics are for listed models, and non-standard models may per
form differently.Please contact our technical support for more detail.
6. Please contact our technical support for any specific requirement.
7. Specifications of this product are subject to changes without prior notice.
Page 4 of 4
1S7B_6UP – Rev. 2020-2.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明