20DRW4 [GAPTEC]
20W - Single Output - Wide Input - Isolated & Regulated;型号: | 20DRW4 |
厂家: | GAPTEC |
描述: | 20W - Single Output - Wide Input - Isolated & Regulated |
文件: | 总6页 (文件大小:3408K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
20 Watt
Wide 4:1 input voltage range
Isolation Voltage: 2.25KVDC
Operating Temperature Range:
-40°C to +85°C
Short circuit protection (SCP)
International standard pin-out
Meet the IEC60950, UL60950,
EN60950 approval
High efficiency up to 85%
The 20DRW4_2.25 series are isolated 20W DC-DC products with 4:1 input
voltage. They feature efficiency up to 86%, 2250VDC isolation with
enhanced isolation, operating temperature of -40°C to +85°C,
input under-voltage protection, output short circuit, over-current and
over-voltage protection. Railway vehicle electronic equipment widely
used in 72V, 96V and 110V.
Low ripple & noise
EMI meet EN50121-3-2,
without external components
RoHS Compliance
Over voltage protection
Over load protection
Input under voltage protection
Meets requirements of rail-
way standard EN50155
Common specifications
Short circuit protection:
Cooling:
Output specifications
Continuous, automatic recovery
Free air convection
-40°C~+85°C
Item
Test condition
Min
Typ
1
Max
3
Units
%
Voltage accuracy
Line regulation
Load regulation
0%-100% load
Operation temperature range:
Storage temperature range:
Maximum case temperature:
Solding temperature:
Switching frequency:
Storage humidity range:
Shock and vibration test:
Case material:
Full load, low to high
0%-100% load
0.2
0.5
300
0.5
1
%
-55°C~+125°C
%
105°C
Transient recovery 25% load step change
time
500
µs
300°C MAX, 1.5mm from case for 10sec
300kHz TYP, PWM mode
95% MAX
Transient respon-
se deviation
normal Vin, 25% load
step change
• 3.3V/5V output
• Others
3
3
5
8
%
%
IEC 61373, car body 1 B mold
Aluminum alloy
Temperature
coefficient
0.02
0.03
%/°C
Potting material:
Epoxy (UL94V-0)
Ripple and noise*
Trim
20MHz Bandwidth
50
100
110
mVp-p
%Vo
MTBF (MIL-HDBK-217F @25°C):
Dimensions:
>1,000 Khours
90
Over voltage
protection
Input voltage range
Input voltage range
110
160
%Vo
50.80*25.40*11.80mm
50.80*25.40*16.30mm (heatsink)
Over current
protection
120
210
%Io
Weight:
26g/34g (heatsink)
* 0%-5% load ripple & noise is no more than 5%Vo. Ripple & noise are measured
by ”parallel cable” method, please see DC-DC converter application notes for
specific operation.
Input specifications
Item
Test condition
• 3.3V output
Min Typ
Max
Units
Input current
(full load / no load) • 5V output
• Others
183/10
217/10
214/3
188/20
222/20
219/8
mA
mA
mA
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
Reflected ripple
current
Nominal Vin and full
load
25
mA
Isolation voltage*
• Input-output
2250
VDC
VDC
• Input and output res- 1600
pectively on the shell
Surge voltage
1sec. max.
100% load
-0.7
28
180
40
VDC
VDC
VDC
ms
Starting voltage
Shutdown voltage
Starting time
Isolation resistance
Input-output, test at
500VDC
1000
MΩ
pF
33
10
Isolation capaci-
tance
Input-output,
100KHz/0.1V
2200
Nominal Vin and
constant resistive
load
* Test time of 1 minute and the leak current lower than 1mA.
Input filter
Hot plug
Pi Type
Unavailable
Example:
Ctrl
• Module switch ON
Ctrl suspended or connected to
TTL high level (3.5-12VDC)
Ctrl pin connected to GND or low
level (0-1.2VDC)
20DRW4_11005S2.25
(the voltage of Ctrl
pin is relative to input
pin GND)
20= 20Watt; D= DIP; R= series; W4= wide input (4:1) 40-160Vin;
5Vout; S= single output; 2.25= 2250VDC
• Module switch OFF
• Input current when
switched OFF
2
7
mA
Note:
1. Only typical model listed. Non-standard models will be different from the above,
please contact us for more details.
2. All specifications are typical at nominal input, full load and 25°C unless
otherwise stated.
3. In this datasheet, all the test methods of indications are based on corporate
standards.
Page 1 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
EMC specifications
EMI
CE
CISPR22/ EN55022
CISPR22/ EN55022
CLASS A (see EMC recommended circuit, fig. 2)
CLASS B (see EMC recommended circuit, fig. 4)
EMI
RE
CLASS A (without external components)
CLASS B (see EMC recommended circuit, fig. 4)
EMS
EMI
ESD
RS
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-5
Contact 6KV/Air 8KV
10V/m
perf. Criteria B
perf. Criteria A
perf. Criteria B
perf. Criteria B
EMI*
EMS
EFT
Surge
4KV (EMC recommended circuit, fig. 3 or fig. 4)
line to line 2KV (2Ω 0.5uF see EMC recommended circuit, fig. 3)
line to ground 4KV (12Ω 0.5uF see EMC recommended circuit, fig. 3)
EMS
EMI
Surge
CS
EN50121-3-2
line to line 1KV (42Ω 0.5uF see EMC recommended circuit, fig. 4)
line to ground 2KV (42Ω 0.5uF see EMC recommended circuit, fig. 4)
perf. Criteria B
perf. Criteria A
IEC/EN61000-4-6
10 Vr.m.s
Part Number
Input Voltage [VDC]
Output Voltage [VDC]
Output Current [mA]
Efficiency
[%, typ.]
Capacitor load
Nominal
Range
40-160
40-160
40-160
40-160
40-160
Full load
[µF, max.]
10000
10000
1600
20DRW4_11003S2.25
20DRW4_11005S2.25
20DRW4_11012S2.25
20DRW4_11015S2.25
20DRW4_11024S2.25
110
3.3
5
5000
4000
1667
1333
82
84
85
86
86
110
110
12
15
24
110
1000
110
833
470
Typical characteristics
For 20DRW4_11003S2.25:
Note: Except 20DRW4_11003S2.25/ 20DRW4_11005S2.25
For 20DRW4_11005S2.25:
Page 2 of 6
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
Efficiency
20DRW4_11005S2.25
20DRW4_11005S2.25
20DRW4_11024S2.25
20DRW4_11024S2.25
Typical application
All the DC/DC converters of this series are tested according to the
recommended circuit (see Fig. 1) before delivery.
If it is required to further reduce input and output ripple, properly
increase the input & output of additional capacitors Cin and Cout
or select capacitors of low equivalent impedance provided that
the capacitance is no larger than the max. capacitive load of the
product.
Vout (VDC)
3.3/5
Fuse
Cin
Cout
470µF
220µF
100µF
2A slow blow
2A slow blow
2A slow blow
10µF - 47µF
10µF - 47µF
10µF - 47µF
12/15
24
figure 1
Page 3 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
EMC solution recommended circuit
Figure 2 parameter descricption:
Cin
27uF -100µF/250V
Refer to the Cout in fig. 1
Cout
Note: Fig. 1 Cin please use the 250V withstand volta-
ge of the capacitor.
figure 2
figure 3
Figure 3 parameter descricption:
FUSE
Choose according to actual input current
FC-CX1D
FC-CX1D is the EMC auxiliary component of our
company. Input voltage range: 40V-160V
C0
C1
100µF/200V
Refer to the Cin in Fig. 1
Refer to the Cout in Fig. 1
1000pF/400VAC
C2
CY1, CY2
Note: Part ①1 in the Fig. 4 is used for EMS test and part ②2
for EMI filtering; selected based on needs.
figure 4
Figure 4 parameter descricption:
C0
100µF/200V
C1, C2
0.22µF/250V
Refer to the Cin in Fig. 1
C3
LCM1
LCM2
15mH (UU common mode inductance)
15mH (UU common mode inductance)
1000pF/400VAC
CY1, CY2, CY3, CY4
C4
Refer to the Cout in Fig. 1
It is not allowed to connect modules output in parallel to enlarge the power.
Page 4 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
Trim application & trim resistance
Application circuit for TRIM (Part in broken line is the interior of models)
Note: Leave open if not used. RT: Resistance of Trim. a: User-defined
parameter, no actual meanings.
Vout(V)
R1(KΩ)
4.801
R2(KΩ)
2.87
R3(KΩ)
10
Vref(V)
1.24
2.5
3.3
5
2.883
2.87
10
12
15
24
11.000
14.384
24.872
2.87
15
2.5
2.87
15
2.5
2.87
17.8
2.5
Mechanical dimensions
Note:
Unit: mm[inch]
Pin diameter tolerances 0.1mm [ 0.004inch]
Page 5 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
20DRW4_2.25 Series
20W - Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
Mechanical dimensions (with heatsink)
Note:
Unit: mm[inch]
General tolerances: 0.5mm [ 0.02inch]
Page 6 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
20DRW4_2.25 – Rev. 2017-1.1
Specifications subject to change without notice.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明