40DAWE_4824S1.5 [GAPTEC]

40W - Single Output - Wide Input - Isolated & Regulated;


型号：	40DAWE_4824S1.5
厂家：	GAPTEC
描述：	40W - Single Output - Wide Input - Isolated & Regulated
文件：	总5页 (文件大小：2793K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

40DAWE_1.5 series

40W - Single Output - Wide Input - Isolated & Regulated

DC-DC Converter

40 Watt

High eﬃciency up to 91%

2:1 wide input voltage range

Isolation voltage 1500VDC

Six-sided metal shield

Short circuit protection (SCP)

(automatic recovery)

Operating temperature:

The 40DAWE_1.5 series are isolated 40W DC-DC products with 2:1 input

voltage. They feature eﬃciency up to 91%, 1500VDC isolation, operating

temperature of -40°C to +85°C, output short circuit protection, over-

voltage protection, over-current protection , which make them widely

applied in data transmission device, battery power supply device,

telecommunication device, distributed power supply system, remote

control system, industrial robot ﬁelds.

-40°C to +85°C

Over voltage protection

Over current protection

Industry standard pinout

EN62368 approved

UL-62368-1 (E347551)

Common speciﬁcations

Cooling:

Output speciﬁcations

Free air convection

Item

Test condition

0%-100% load

Min Typ

Max

Units

Short circuit protection:

Operation temperature range:

Storage temperature range:

Vibration:

Hiccup, auto-recovery

-40°C~+85°C

Voltage accuracy

Line regulation

input voltage from low

to high @full load

0.2

0.5

-55°C~+125°C

Load regulation

0% to 100% load

10-55Hz, 10G, 30 Min. along X, Y and Z

300°C MAX, 1.5mm from case for 10 sec

300kHz TYP

Transient recovery 25% load step change

time

300

500

µs

Pin welding resistance temperature:

Switching frequency (PWM mode)*:

Humidity:

Transient respon-

se deviation

25% load step change

non-condensing, 95% MAX

Aluminum alloy

Temperature

coeﬃcient

Full load

0.03

%/°C

Case material:

Potting material:

Epoxy (UL94V-0 rated)

500,000 hours

Ripple and noise*

Trim

20MHz Bandwidth

100

MTBF (MIL-HDBK-217F @25°C)*:

Weight:

%Vo

26.8g (Typ.) - 36g with heatsink

Over voltage

protection

Input voltage range

110

160

190

Dimensions:

50.80 × 25.40 × 11.80 mm

51.40 × 26.20 × 16.50 mm (heatsink)

Over current

protection

110

%Io

* This series of products using reduced frequency technology, the switching

frequency is test value of full load. When the load is reduced to below 50%, the

* Test ripple and noise by “parallel cable” method.

Input speciﬁcations

Isolation speciﬁcations

Item

Test condition

Min

Typ

Max

Units

Item

Test condition

Min

Typ

Max

Units

VDC

Input current

(full load/no load)

• 24Vin

• 48Vin

1894/60

926/12

1938/100 mA

947/25

Isolation voltage

Input/Output, tested

for 1 minute and 1mA

max

1500

Reﬂected ripple

current

Nominal input

voltage

Isolation resistance

Test at 500VDC/60sec 1000

MΩ

Isolation capacitance Input/Output,

100KHz/0.1V

2000

Surge voltage

(1s max.)

• 24Vin

• 48Vin

-0.7

100

VDC

Input under-voltage • 24Vin

15.5

VDC

protection

• 48Vin

Example:

Starting voltage

• 24Vin

• 48Vin

VDC

40DAWE_2415S1.5

40 = 40Watt; D = DIP; A = series; W = wide input (2:1); E = Eco series;

9-36Vin; 15Vout; S = single output; 1.5 = 1500VDC isolation

Input ﬁlter

Hot plug

Pi type

Unavailable

• Module ON

Ctrl

Ctrl suspended or connected to

TTL high level (3.5-12VDC)

Ctrl pin connected to GND or low

level (0-1.2VDC)

Note:

(The voltage of Ctrl

pin is relative to

input pin GND.)

1. Input voltage can’t exceed this value, or will cause the permanent damage.

2. The load shouldn‘t be less than 5%, otherwise ripple will increase dramatically.

3. Max. Capacitive Load is tested on Vin-nominal and full load.

4. All speciﬁcations measured at Ta = 25°C, humidity <75%, nominal input voltage

and rated output load unless otherwise speciﬁed.

• Module OFF

• Input current

when switched OFF

5. In this datasheet, all the test methods of indications are based on corporate

standards.

6. Only typical models listed, other models may be diﬀerent, please contact our

technical person for more details.

7. Speciﬁcations subject to change without notice.

Page 1 of 5

40DAWE_1.5 – Rev. 2020-1.2

Speciﬁcations subject to change without notice.

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

40DAWE_1.5 series

40W - Single Output - Wide Input - Isolated & Regulated

DC-DC Converter

EMC speciﬁcations

EMI

CISPR32/EN55032

IEC/EN61000-4-2

IEC/EN61000-4-3

IEC/EN61000-4-4

IEC/EN61000-4-5

IEC/EN61000-4-6

CLASS B

(External Circuit Refer to EMC recommended circuit, ②)

perf. Criteria A

EMI

CLASS B

EMS

ESD

Contact 6KV

10V/m

perf. Criteria A

EFT

Surge

2KV

perf. Criteria A (External Circuit Refer to recommended circuit, ①)

perf. Criteria A

line to line 2KV

10 Vr.m.s

Part Number

Input Voltage Range [VDC]

Output Voltage

[VDC]

Output Current

[mA, max]

Eﬃciency**

[%, Typ.]

Capacitive load

[µF, max.]

nominal

Range

18-36

36-75

Max.

40DAWE_2405S1.5

40DAWE_2412S1.5

40DAWE_2415S1.5

40DAWE_2424S1.5

40DAWE_4812S1.5

40DAWE_4815S1.5

40DAWE_4824S1.5

8000

3333

2667

1667

3333

2667

1667

10000

2700

1680

680

2700

1680

680

Add suﬃx “H” for heatsink mounted, for example: 40DAWE_2412SH1.5

Typical characteristics

40DAWE_2405S1.5

40DAWE_2424S1.5

Page 2 of 5

40DAWE_1.5 – Rev. 2020-1.2

Speciﬁcations subject to change without notice.

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

40DAWE_1.5 series

40W - Single Output - Wide Input - Isolated & Regulated

DC-DC Converter

Eﬃciency

40DAWE_4812S1.5

Typical application and EMC solution recommended circuit

Page 3 of 5

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

40DAWE_1.5 – Rev. 2020-1.2

Speciﬁcations subject to change without notice.

40DAWE_1.5 series

40W - Single Output - Wide Input - Isolated & Regulated

DC-DC Converter

Application of Trim and calculation of trim resistance

It is not allowed to connect modules output in parallel to enlarge the power.

Mechanical dimensions

Note:

Unit: mm[inch]

General tolerances: 0.5mm [ 0.020inch]

Page 4 of 5

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

40DAWE_1.5 – Rev. 2020-1.2

Speciﬁcations subject to change without notice.

40DAWE_1.5 series

40W - Single Output - Wide Input - Isolated & Regulated

DC-DC Converter

Mechanical dimensions

Page 5 of 5

40DAWE_1.5 – Rev. 2020-1.2

Speciﬁcations subject to change without notice.

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

相关型号：