6DAW4_4815D1.5 [GAPTEC]
6W - Dual/Single Output - Wide Input - Isolated & Regulated;
| 型号： | 6DAW4_4815D1.5 |
| 厂家： | 
GAPTEC |
| 描述： | 6W - Dual/Single Output - Wide Input - Isolated & Regulated |
| 文件： | 总5页 (文件大小：1021K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
6DAW4_1.5 Series
6W - Dual/Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
6 Watt
Efficiency up to 88%
4:1 wide input voltage range
1.5kVDC input/output
isolation
Operating temperature:
-40°C ~ +85°C
The 6DAW4 series are specially designed for applications where a wide
range input voltage power supplies are isolated from the input power
supply in a distributed power supply system on a circuit board.
Input under-voltage
Over-voltage protection
Over-current protection
Meet CISPR22/EN55022 CLASS A
Int. standard pin-out
Meet UL60950 , EN60950 and
IEC60950
Continuous short circuit
protection (SCP)
These products apply to:
1) Where the voltage of the input power supply is wide range
(voltage range≤ 4:1);
Output over voltage protec-
tion
2) Where isolation is necessary between input and output
(isolation ≤1500VDC);
3) Where the regulation of the output voltage and the output ripple
noise are demanded.
UL-60950-1 (E347551)
Common specifications
Short circuit protection:
Cooling:
Output specifications
Continuous, automatic recovery
Free air convection
Item
Test condition
Min
Typ
1
Max
3
Units
%
Output voltage
accuracy
Operation temperature range:
(power derating above 71°C)
-40°C~+85°C
Output voltage
balance
Dual output, balance
load
0.5
1.5
%
Storage temperature range:
Lead temperature range:
Maximum case temperature:
-55°C ~ +125°C
Line regulation
Full load, Input volta-
ge from low to high
• positive output
300°C MAX, 1.5mm from case for 10 sec
0.2
0.5
0.5
1
%
%
105°C (Operating Temperature curve
range)
• negative output
Load regulation
Cross regulation
5% to 100% load
• positive output
• negative output
Storage humidity range:
Vibration:
< 95% (non condensing)
-55Hz, 10G, 30 Min. along X, Y and Z
300KHz TYP (PWM mode)
Aluminium alloy
0.5
0.5
1
%
%
1.5
Switching frequency:
Case material:
Dual output, main
circuit with 50% load,
auxiliary circuit with
10%-100% load
0.5
%
MTBF (M1L-HDBK-217F):
>1,000,000 hours
Temperature drift 100% full load
0.03 %/°C
85 mVp-p
Ripple&Noise*
20MHz Bandwidth
Input specifications
Transient recove-
ry time
25% load step change
300
500
µs
Item
Test condition
Min
Typ
Max
Units
Input current
• 24VDC input
• 48VDC input
301/5 309/12
148/4 154/8
mA
mA
Transient respon-
se deviation
25% load step change
• 3.3V, 5V, 5V output
• others
(full load/no load)
5
3
8
5
%
%
Reflected ripple current
20
mA
Over voltage
protection
Input voltage range
110
110
160
%Vo
Input impulse voltage
(1sec. max.)
• 24VDC input
• 48VDC input
-0.7
-0.7
50
VDC
VDC
100
Over current
protection
Input voltage range
140
190
%lo
Starting voltage
• 24VDC input
• 48VDC input
9
18
VDC
VDC
Under-voltage turn-off
• 24VDC input
• 48VDC input
5.5
14
6.5
15.5
VDC
VDC
* Ripple and noise tested by “parallel cable” method. See detailed operation
instructions at Testing of Power Converter section, application notes.
Input filter
Hot plug
Pi
Example:
6DAW4_2405D1.5
Unavailable
6 = 6Watt; D = DIP; A = series; W4 = wide input (4:1) 9-36Vin;
5Vout; D = Dual Output; 1.5 = 1500VDC
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
VDC
Note:
Isolation voltage
Tested for 1 minute
and 1mA max
1500
1. The load shouldn‘t be less than 10%, otherwise ripple will increase
dramatically.
Isolation resistance
Test at 500VDC
1000
MΩ
pF
2. Operation under 10% load will not damage the converter; However, they may
not meet all specifications listed.
Isolation capacitance Input/Output
100KHz/0.1V
1000
3. All specifications measured at Ta = 25°C, humidity <75%, nominal input
voltage and rated output load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate
standards.
5. Only typical models listed, other models may be different, please contact our
technical person for more details.
Page 1 of 5
6DAW4_1.5 – Rev. 2020-1.5
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
6DAW4_1.5 Series
6W - Dual/Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
EMC specifications
EMI
CE
CISPR22/EN55022
CLASS A (without external circuit)
CLASS B (External Circuit Refer to EMC recommended circuit, 2 )
EMI
RE
CISPR22/EN55022
CLASS A (without external circuit)
CLASS B (External Circuit Refer to recommended circuit, 2 )
EMS
EMS
EMS
EMS
EMS
EMS
ESD
RS
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-5
IEC/EN61000-4-6
Contact 4KV
10V/m
perf. Criteria B
perf. Criteria A
perf. Criteria B
perf. Criteria B
perf. Criteria A
perf. Criteria B
EFT
Surge
CS
2KV
(External Circuit Refer to recommended circuit, 1 )
(External Circuit Refer to recommended circuit, 1 )
2KV
3 Vr.m.s
Voltage dips, short
and interruptions
immunity
IEC/EN61000-4-29 0%-70%
Part Number
Input Voltage [VDC]
Output Voltage
Output current [mA]
Capacitive load
[µF, Max.]
Efficiency** [%, Typ.]
Nominal
Range
9-36
9-36
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
18-75
9-36
9-36
9-36
9-36
18-75
18-75
18-75
Max*
40
40
40
40
40
40
80
80
80
80
80
40
40
40
40
80
80
80
[VDC]
3.3
5
Max
1500
1200
667
Min
75
60
33
25
20
10
75
60
25
20
13
6DAW4_2403S1.5
6DAW4_2405S1.5
6DAW4_2409S1.5
6DAW4_2412S1.5
6DAW4_2415S1.5
6DAW4_2424S1.5
6DAW4_4803S1.5
6DAW4_4805S1.5
6DAW4_4812S1.5
6DAW4_4815S1.5
6DAW4_4824S1.5
6DAW4_2405D1.5
6DAW4_2412D1.5
6DAW4_2415D1.5
6DAW4_2424D1.5
6DAW4_4805S1.5
6DAW4_4812D1.5
6DAW4_4815D1.5
24
1800
1000
1000
470
220
100
79
83
84
87
88
87
80
84
87
88
87
83
87
88
87
83
87
88
24
24
9
24
12
15
15
3.3
5
500
400
250
1500
1200
500
400
250
600
250
200
125
24
24
48
1800
1000
470
220
100
48
48
12
15
24
5
48
48
24
30
12
680
330
24
12
15
24
5
24
10
6
220
100
24
48
600
250
200
30
12
680
470
220
48
12
15
48
10
*
Input voltage can’t exceed this value, or it will cause permanent damage.
** Efficiency is measured In nominal input voltage and rated output load.
Typical characteristics
Page 2 of 5
6DAW4_1.5 – Rev. 2020-1.5
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
6DAW4_1.5 Series
6W - Dual/Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
Efficiency
6DAW4_2405S1.5
6DAW4_2405S1.5
6DAW4_4815D1.5
6DAW4_4815D1.5
Recommended circuit
All the DC/DC converters of this series are tested according to the re-
commended circuit before delivery.
If it is required to further reduce input and output ripple, properly in-
crease the input & output of additional capacitors Cin and Cout or
select capacitors of low equivalent impedance provided that the capa-
citance is no larger than the max. capacitive load of the product.
The product does not support output in parallel with power per liter.
Page 3 of 5
6DAW4_1.5 – Rev. 2020-1.5
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
6DAW4_1.5 Series
6W - Dual/Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
EMC recommended circuit
Parameters
FUSE
Vin: 24V
Vin: 48V
Choose according to practical input
current
MOV
LDM1
C0
S14K35
S14K60
6DAW4
56µH
330µF/50V
1µF/50V
330µF/100V
1µF/100V
C1
C2
Refer to the Cout in recommended circuit
LDM1
CY1
CY2
4.7µH
1nF/2kV
1nF/2kV
Part ①1 is for EMS test, part ②2 is for EMI filtering; parts
①
can be added based on actual requirement.
EMC recommended circuit PCB layout
Page 4 of 5
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
6DAW4_1.5 – Rev. 2020-1.5
Specifications subject to change without notice.
6DAW4_1.5 Series
6W - Dual/Single Output - Wide Input - Isolated & Regulated
DC-DC Converter
Mechanical dimensions and foot-
Note:
Unit: mm[inch]
Grid: 2.54*2.54mm.
Pin section tolerances: 0.10mm [ 0.004inch]
General tolerances: 0.25mm [ 0.010inch]
Page 5 of 5
6DAW4_1.5 – Rev. 2020-1.5
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明