6DAW4_4815S3 [GAPTEC]

6W - Single Output - 4:1 Wide Input - Isolated & Regulated;


型号：	6DAW4_4815S3
厂家：	GAPTEC
描述：	6W - Single Output - 4:1 Wide Input - Isolated & Regulated
文件：	总4页 (文件大小：847K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

6DAW4_S3 Series

6W - Single Output - 4:1 Wide Input - Isolated & Regulated

DIP DC-DC Converter

DC-DC Converter

6 Watt

The 6DAW4 series are specially designed for applications where a wide

range input voltage power supplies are isolated from the input power

supply in a distributed power supply system on a circuit board.

High Efﬁciency up to 88%

Operating Temperature:

-40°C to +85°C

3KVDC Input/Output Isolation

Short Circuit Protection SCP

(Automatic recovery)

No-load power consumption

as low as 0.12W

Over-voltage protection

Over-current protection

Input under-voltage protection

Meet CISPR22/EN55022

CLASS A

These products apply to:

1) Where the voltage of the input power supply is wide range

(voltage range≤ 4:1);

2) Where isolation is necessary between input and output

(isolation≤3000VDC);

Industry standard pin-out

RoHS Compliance

3) Where the regulation of the output voltage and the output ripple

noise are demanded.

Common speciﬁcations

Short circuit protection:

Cooling:

Output speciﬁcations

Continuous, automatic recovery

Free air convection

-40°C~+85°C

Item

Test condition

Min Typ

Max

Units

ꢀ

Output voltage

accuracy

Refer to recommended

circuit

Operation temperature range:

Storage temperature range:

Temperature rise at full load:

Lead temperature range:

Vibration:

Line regulation

(at full load)

Input voltage from low

to high

0.2

0.5

ꢀ

-55°C ~+125°C

40°C TYP

Load regulation

from 5ꢀ to 100ꢀ load

25ꢀ load step change

0.5

2.0

ꢀ

300°C MAX, 1.5mm from case for 10 sec

10-55Hz, 10G, 30 Min. along X, Y and Z

< 95ꢀ

Transient Recovery

Time

300

500

µs

Transient Response

Deviation

25ꢀ load step change

ꢀ

Storage humidity range:

Case material:

Plastic(UL94-V0)

Temperature drift

(Vout)

Refer to recommended

circuit

0.03 ꢀ/°C

MTBF (MIL-HDBK-217F@25°C):

Weight:

>1,000,000 hours

13g

Ripple & Noise*

20MHz Bandwidth

Input voltage range

120

mVp-p

ꢀVo

Over-voltage

protection

110

160

Input speciﬁcations

Over-current

protection

Input voltage range

110 140

300

190

ꢀIo

KHz

Item

Test condition

Min Typ

Max

Units

Input ﬁlter

Switching frequency PWM mode

Input current

(full load / no load)

24VDC input:

• 3.3V output

• 5V output

261/5 268/8 mA

301/5 309/8 mA

284/5 291/8 mA

Test ripple and noise by “parallel cable” method. See detailed operation

instructions at Testing of Power Converter section, application notes.

• other output

48VDC input:

• 3.3V output

• 5V output

131/4 134/7 mA

151/4 154/7 mA

142/4 145/7 mA

Model selection:

WCTV_xxyyN##

• other output

W= Watt; C= Case; T= Type; V=Voltage Variation (omitted 10ꢀ);

xx= Vin; yy=Vout; N= Numbers of Output; ##= Isolation (kVDC)

Reﬂected ripple current • 24VDC input

• 48VDC input

Example:

Input impulse voltage

(1sec. max.)

• 24VDC input

• 48VDC input

-0.7

100

VDC

6DAW4_2405S3

6= 6Watt; D= DIP; A= series; W4= wide input (4:1) 9-36Vin; 5Vout;

D= Dual Output; 3= 3000VDC

Start-up voltage

Under-voltage turn-off

Starting time

• 24VDC input

• 48VDC input

VDC

• 24VDC input

• 48VDC input

5.5

6.5

15.5

VDC

Nominal input &

constant resistance

load

Hot plug

Unavailable

Note:

1. The load shouldn‘t be less than 10ꢀ, otherwise ripple will increase

dramatically.

Isolation speciﬁcations

Item

2. Operation under 10ꢀ load will not damage the converter; However, they may

not meet all speciﬁcations listed.

3. All speciﬁcations measured at Ta=25°C, humidity<75ꢀ, nominal input voltage

and rated output load unless otherwise speciﬁed.

4. In this datasheet, all the test methods of indications are based on corporate

standards.

5. Only typical models listed, other models may be different, please contact our

technical person for more details.

Test condition

Min

Typ

Max

Units

VDC

Isolation voltage

Tested for 1 minute

and 1mA max

3000

Isolation resistance

Isolation capacitance

Test at 500VDC

1000

MΩ

Input-output,

100KHz/0.1V

Page 1 of 4

6DAW4_S3 – Rev. 2016-1.3

Speciﬁcations subject to change without notice.

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

6DAW4_S3 Series

6W - Single Output - 4:1 Wide Input - Isolated & Regulated

DIP DC-DC Converter

EMC speciﬁcations

EMI

CISPR22/EN55022

CLASS A (bare component)

CLASS B (External Circuit Refer to EMC recommended circuit, 2 )

EMI

CISPR22/EN55022

CLASS A (bare component)

CLASS B (External Circuit Refer to recommended circuit, 2 )

EMS

ESD

IEC/EN61000-4-2 Contact 4KV

IEC/EN61000-4-3 10V/m

perf. Criteria B

perf. Criteria A

perf. Criteria B

perf. Criteria A

perf. Criteria B

EFT

Surge

IEC/EN61000-4-4

IEC/EN61000-4-5

2KV

(External Circuit Refer to recommended circuit, 1 )

IEC/EN61000-4-6 3 Vr.m.s

IEC/EN61000-4-29 0ꢀ-70ꢀ

Voltage dips, short and

interruptions immunity

Part Number

Input Voltage [VDC]

Output Voltage [VDC]

Current [mA]

Max

Efﬁciency [%, Typ.]

Max. Capacative Load [µF]

Nominal

Range

Max*

Min

6DAW4_2403S3

6DAW4_2405S3

6DAW4_2409S3

6DAW4_2412S3

6DAW4_2415S3

6DAW4_2424S3

6DAW4_4803S3

6DAW4_4805S3

6DAW4_4812S3

6DAW4_4815S3

6DAW4_4824S3

9-36

3.3

1500

1200

667

2200

1000

680

9-36

3.3

500

9-36

400

470

9-36

250

330

18-72

1500

1200

500

2200

680

400

470

250

330

* Input voltage can’t exceed this value, or it will cause permanent damage.

Typical characteristics

Page 2 of 4

GAPTEC-Electronic GmbH & Co. KG

6DAW4_S3 – Rev. 2016-1.3

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

6DAW4_S3 Series

6W - Single Output - 4:1 Wide Input - Isolated & Regulated

DIP DC-DC Converter

Efﬁciency

6DAW4_2405S3

6DAW4_4815S3

Typical application

All the DC/DC converters of this series are tested according to the recom-

mended circuit (see Fig. 1) before delivery.

If it is required to further reduce input and output ripple, properly incre-

ase the input & output of additional capacitors Cin and Cout or select

capacitors of low equivalent impedance provided that the capacitance is

no larger than the max. capacitive load of the product.

Figure 1

Vin (VDC)

Cin (uF)

100

Cout (uF)

10~47

Page 3 of 4

6DAW4_S3 – Rev. 2016-1.3

Speciﬁcations subject to change without notice.

GAPTEC-Electronic GmbH & Co. KG

sales@gaptec-electronic.com – www.gaptec-electronic.com

6DAW4_S3 Series

6W - Single Output - 4:1 Wide Input - Isolated & Regulated

DIP DC-DC Converter

EMC solution-recommended circuit

Parameters

FUSE

MOV

Vin: 24V

Vin: 48V

Choose according to actual input current

S14K35

330µF/50V

2.2µF/50V

S14K60

330µF/100V

2.2µF/100V

C1, C2

LCM

2.2µH

Refer to the Cout in Typical application

Notes: Part 1 is used for EMS test and part 2 for EMI

ﬁltering; selected based on needs.

EMC solution-recommended circuit PCB Layout

Recommended footprint

The product does not support output in parallel with power per liter.

Mechanical dimensions

Note:

Unit: mm[inch]

Pin diameter tolerances: 0.10mm [ 0.004inch]

General tolerances: 0.25mm [ 0.010inch]

Page 4 of 4

GAPTEC-Electronic GmbH & Co. KG

6DAW4_S3 – Rev. 2016-1.3

sales@gaptec-electronic.com – www.gaptec-electronic.com

Speciﬁcations subject to change without notice.

相关型号：