LEDT16_24-300 [GAPTEC]
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated;型号: | LEDT16_24-300 |
厂家: | GAPTEC |
描述: | Constant current power LED Driver - Wide Input - Non-Isolated & Regulated |
文件: | 总6页 (文件大小:1868K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
LED Driver
The LED16_24 is a series of step-down constant current source designed for
driving high power LEDs. It features high efficiency, wide input voltage range,
high operating temperature, PWM and analogue dimming, remote ON/OFF con-
trol, and SMD package which facilitates the installation.
SMD package, simple and
convenient
High efficiency up to 96%
Short Circuit Protection (SCP)
Ultra wide range voltage
input and output
Constant current mode, great
power output
AC-DC, EMC recommended
circuit
PWM dimming & analogue
dimming
It is widely used in LED illumination areas such as decorative light, special con-
trol light, backlight, commercial light, streetlight, in-house light and car light,
etc.
Remote ON/OFF
RoHS and UL Compliance
Specifications
PWM dimming and ON/OFF control (leave open if not used)
Item
Test condition
≤10 seconds
Min
5
Typ
24
Max
55
Units
VDC
Item
Test condition
Min
Typ
Max
Units
Utmost input
voltage
Remote ON/OFF
ON
Open or 2.8V<Vc<6V
Vc<0.6V
OFF (shutdown)
Recommended
input voltage
5.5
48
VDC
Remote pin current Vc=5V
1
mA
Quiescent input
current
Vin=24V, Vc <0.6V
400
Typ
µA
Input filter
Capacitor (1µF)
Vin=48V
Output voltage
range
3.3
2
36
4
VDC
VDC
PWM frequency
200
Hz
Input-Output
voltage drop
Vin=5.5~48V, 1~10LEDs
Analogue dimming (leave open if not used)
Item
Test condition
Min
Max
Units
Output current
range
See the product
program
Input voltage range Vin=5.5-48V
0-15V
Output current
accuracy
2
5
1
%
%
Output current
range
Vin=5.5-48V
0%-100%
Output current
stability
Vin=48V, Vo=3.3V~36V
Vin=24V, 5LEDS
Control voltage
range
Full on
Full off
0.2V 50mV
4.5V 200mV
Internal power
dissipation
Driving current
Vc=5V
0.6mA(max)
Temperature
coefficient
-40 °C to +71 °C
ambient
0.015
96
%/°C
%
EMC specifications
Efficiency at full
load
EMI conducted EN55015 power port*
RFI cunducted
EN55015
CISPR22
class B*
Ripple & Noise
(Vp-p)
120
mV
ESD
R/S
IEC/EN 61000-4-2 level 2 contact 4KV perf. Criteria B*
Short circuit
protection
Continuous,
automatic recovery
IEC/EN 61000-4-3 level 3 (10V/m)
IEC/EN 61000-4-4 level 2 ( 1KV)
IEC/EN 61000-4-5 level 2 ( 1KV)
IEC/EN 61000-4-6 level 3 (10Vr.ms)
perf. Criteria A
perf. Criteria B*
perf. Criteria B*
perf. Criteria A
EFT
Operating tempera-
ture range
• 300mA / 350mA
• 500mA/ 600mA/
700mA
-40
-40
85
71
°C
°C
Surge
C/S
Storage tempera-
ture range
-55
125
°C
* Refer to EMI/EMC recommended circuit
Maximum case
temperature
100
°C
Model selection:
Maximum capacitive
Load
1000
370
µF
LEDC_xx-###
LED=Type; C=Case; yy=Vin; ###= Output Current
Operating frequen-
cy range
320
420
kHz
Hours
Example:
LEDT16_24-300
LED= Series T16= SMT16; yy= 24VDC nominal; 300= 0,3A
MTBF
MIL-HDBK-217F(+25°C)
Epoxy Resin (UL94-V0)
2,000,000
Case Material
Dimensions
Weight
23.86*18.10*8.00
6
mm
g
Page 1 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
Part Number
Input Voltage [VDC]
Nominal (Range)
Output Voltage
[VDC]
Output Current
[mA]
Dimming control
Efficiency
[%, typ]
LEDT16_24-300
LEDT16_24-350
LEDT16_24-500
LEDT16_24-600
LEDT16_24-700
24 (5.5-48)
24 (5.5-48)
24 (5.5-48)
24 (5.5-48)
24 (5.5-48)
3.3-36
3.3-36
3.3-36
3.3-36
3.3-36
0-300
0-350
0-500
0-600
0-700
PWM+Analogue
PWM+Analogue
PWM+Analogue
PWM+Analogue
PWM+Analogue
96
96
96
96
96
Input vs. Output
Input voltage
Output voltage
range [VDC]
Output constant
current [mA]
Output power
[W, max]
Input voltage
Output voltage
Output constant
current [mA]
Output power
[W, max]
range [VDC]
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
48
36
24
20
15
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
300
300
300
300
300
300
300
10.80
9.60
6.30
5.10
48
36
24
20
15
600
600
600
600
600
600
600
21.60
19.20
12.60
10.20
7.92
3.96
3.00
1.20
3.3-13.2
12
12
3.3-10.0
3.3-4.0
6.00
2.40
5.5
5.5
Input voltage
Output voltage
range [VDC]
Output constant
current [mA]
Output power
[W, max]
Input voltage
Output voltage
range [VDC]
Output constant
current [mA]
Output power
[W, max]
48
36
24
20
15
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
350
350
350
350
350
350
350
12.60
11.20
7.35
48
36
24
20
15
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
700
700
700
700
700
700
700
25.20
22.40
14.70
11.90
9.24
5.95
4.62
3.50
1.40
12
12
7.00
5.5
5.5
2.80
Input voltage
Output voltage
range [VDC]
Output constant
current [mA]
Output power
[W, max]
48
36
24
20
15
3.3-36.0
3.3-32.0
3.3-21.0
3.3-17.0
3.3-13.2
3.3-10.0
3.3-4.0
500
500
500
500
500
500
500
18.00
16.00
10.50
8.50
6.60
5.00
2.00
12
5.5
Typical application circuits
Page 2 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
Digital dimming control
Io_set refers to the expected output current value.
Io_norm refers to the rated output current
D refers to the pulse width of the PWM signal
T refers to the cycle of the PWM signal
It is natural for the driver to generate an audibly noise in dimming pro-
cess, because the frequency of the control circuit is within human au-
Note: The formula only supplies as a reference, and the output current dibly range (20Hz~20KHz). In order to avoid the human eye can observe
may be a little deviation with different load. The Ton(min) of PWM signal
must be greater than 0.7ms, or the driver can’t be operated normally.
the LED flashes, the PWM dimming frequency is recommended to set
above 100Hz.
Analogue dimming control and application sample
Analogue dimming circuit
Analogue input voltage vs. output
Page 3 of 6
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
EMC recommended circuit
EMI/RFI conducted EN55022 recommended circuit
EMI/EMC recommended circuit
Note:
1. DIM pin is the module’s PWM dimming pin as shown in EMI/EMC recommended circuit.
2. While adding circuit 2 , it may extend the PWM dimming output reaction time.
EMI/EMC standard:
Item
EMI conducted
ESD
Standard
EN 55015
Level
Power port
Level 2
Predicate
Qualification
B
Remark
Add external circuit 1
IEC
4KV
61000-4-2:2001
Add external circuit 2
Surge
EFT
IEC
Level 2
Level 2
B
B
1KV
61000-4-5:2004
Add external circuit 1
IEC
1KV
61000-4-4:2004
Add external circuit 1
1. 24V input series, 24V output series is subject to CY (CY : 1nF/2KV).
2. It is not needed to add the component in the peripheral circuit when
parameter with the symbol of „--“.
Recommended parameter:
Components
Specifications
Tvs
LCM
C0
C1
SMCJ48A,1500W Bringtking
6.8µH CD43
CEAIYA
470µF/50V CapXon
4.7µF/50V
2.2µF/50V
1210 (TORCH)
1210 (TORCH)
C2
C3
470pF/100V 0805 (TORCH)
R1
680Ω 0805 (can replaced by
inductance or magnetic bead)
Page 4 of 6
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
AC input recommended circuit
Typical characteristics
Reflow soldering profile
Efficiency
LEDT16_24-300
LEDT16_24-350
LEDT16_24-500
LEDT16_24-600
LEDT16_24-700
LEDT16_24-300
LEDT16_24-350
LEDT16_24-500
LEDT16_24-600
LEDT16_24-700
LEDT16_24-300
LEDT16_24-350
LEDT16_24-500
LEDT16_24-600
LEDT16_24-700
LEDT16_24-300
LEDT16_24-350
LEDT16_24-500
LEDT16_24-600
LEDT16_24-700
Page 5 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
LEDT16_24 Series
Constant current power LED Driver - Wide Input - Non-Isolated & Regulated
Mechanical dimensions
Recommended footprint
Tube packing dimensions
Note:
1. If the product is not operated within the required load range, the product
perfor-
mance cannot be guaranteed to comply with all parame-
ters in the datasheet;
2. The maximum capacitive load offered were tested at nominal input voltage
and
full load;
3. Unless otherwise specified, parameters in this datasheet were measured under
the conditions of Ta=25 , humidity<75% with nominal input voltage
and rated
output load;
4. All index testing methods are based on our Company’s corporate standards;
5. We can provide product customization service;
6. Specifications are subject to change without prior notice.
Page 6 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LEDT16_24 – Rev. 2018-1.1
Specifications subject to change without notice.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明