LMS78_15-0.5R [GAPTEC]
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output;型号: | LMS78_15-0.5R |
厂家: | GAPTEC |
描述: | Wide Input Non-Isolated & Regulated, Single Positive/Negative Output |
文件: | 总3页 (文件大小:1444K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LMS78_0.5R Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Switching Regulator
Efficiency up to 93%
Operating temperature
range: -40°C ~ +85°C
Pin-out compatible with
LM78xx linears
Short circuit protection (SCP)
Thermal shutdown
Low ripple and noise
Sip package, meet UL94-V0
Low temperature rise
Industry standard pinout
Ultra low no-load power
consumption
The LMS78_0.5R series high efficiency switching regulators are ideally
suited to replace LM78xx linear regulators and are pin compatible.
UL-60950-1 (E347551)
Common specifications
Short circuit protection:
No-load input current:
Reverse Polarity Input:
Input Filter:
Output specifications
Continuous, automatic recovery
0.2mA TYP, 1.5mA MAX
Forbidden
Item
Test conditions
100% load
Min
Typ
2
Max
3
Units
%
Output voltage
accuracy
Line regulation
Input Voltage Range
10% to 100% load
0.2
0.4
0.4
0.6
%
Capacitor Filter
Load regulation
Output current limit
Ripple + Noise*
%
Temperature rise at full load:
Cooling:
25°C MAX, 15°C TYP
Free air convection
3000
75
mA
20MHz Bandwidth
Vin=24VDC
0% -100% load
20
mVp-
p
Operation temperature range:
-40°C~+85°C
Power derating above 71°C
Storage temperature range:
Pin welding resistance temperature:
Operating case temperature:
Storage humidity range:
Package material:
-55°C ~+125°C
Over heat protec-
tion
Internal IC junction
170
1.8
°C
W
260°C MAX, 1.5mm from case for 10 sec
Short circuit input
power
0.5
100°C
< 95%RH
Switching frequency
550
850
250
KHz
mV
Plastic [UL94-V0]
Transient response
deviation
Nominal input, 25%
load step change
55
MTBF:
>2,000,000 hours
+25°C MIL-HDBK-217F
Transient recovery
time
Nominal input, 25%
load step change
0.5
2
ms
Weight:
2g
Temperature coef-
ficient
-40 °C to +85 °C
ambient
0.03
%/°C
Note:
1. The max. capacitive load should be tested within the input voltage range and
under full load conditions;
* Test ripple and noise by “parallel cable” method. With the load lower than 10%,
maximum ripple and noise will be 150mVp-p.
2. Without any special statement, all indexes are only specific to positive output
application;
3. Unless otherwise specified, data in this datasheet should be tested under the
conditions of Ta = 25°C, humidity <75% when inputting nominal voltage and
outputting rated load;
4. All index testing methods in this datasheet are based on our Company’s
corporate standards;
Example:
LMS78_05-0.5R
LM = Series; S = SIP Case; 05 = 5Vout; 0.5 = 0.5A; R = Revised
5. The performance indexes of the product models listed in this manual are as
above, but some indexes of non-standard model products will exceed the
above-mentioned requirements, and please directly contact with our technician
for specific information;
6. Specifications subject to change without prior notice.
EMC specifications
EMI
CE
CISPR22/EN55022
CISPR22/EN55022
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-6
CLASS B
CLASS B
(External circuit refer to EMC recommended circuit, 2 or EMC module application circuit)
(External circuit refer to EMC recommended circuit, 2 or EMC module application circuit)
EMI
RE
EMS
EMS
EMS
EMS
EMS
ESD
RS
Contact 4KV perf. Criteria B
10V/m
2KV
perf. Criteria A
EFT
CS
perf. Criteria B (External circuit refer to EMC recommended circuit, 1 )
3 Vr.m.s
perf. Criteria A
perf. Criteria B
Voltage dips,
short and
interruptions
immunity
IEC/EN61000-4-29 0%-70%
Page 1 of 3
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LMS78_0.5R – Rev. 2020-2.6
Specifications subject to change without notice.
LMS78_0.5R Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Part Number
Input Voltage [VDC]
Nominal (Range)
Output Voltage
[VDC]
Output Current
[mA]
Efficiency
[%, min/typ]
Max. capacitive load
[µF]
LMS78_03-0.5R
LMS78_05-0.5R
24 (4.75-36)
3.3
500
78/81
680
24 (6.5-36)
12 (7-31)
5
-5
500
-300
82/85
78/81
680
330
LMS78_09-0.5R
LMS78_12-0.5R
24 (12-36)
9
500
87/90
680
24 (15-36)
12 (8-24)
12
-12
500
-150
89/92
82/85
680
330
LMS78_15-0.5R
24 (19-36)
12 (8-21)
15
-15
500
-150
90/93
82/85
680
330
Typical characteristics
Typical application circuit
LMS78
LMS78
LMS78
LMS78
Note:
Part number
C1,C3
(Ceramic Capacitor)
C2,C4
(Ceramic Capacitor)
1. C1 and C2 are required and should be connected close to the pin terminal
of the module.
2. The capacitance of C1 and C2 refer to Sheet 1, it can be increased properly
if required, and tantalum or low ESR electrolytic capacitors may also
suffice.
3. When the products used as the circuit like figure 3, an inductor named as
LDM up to 10μH is recommended in the circuit to reduce the mutual
interference.
4. Cannot be used in parallel for output and hot swap.
5. Operation under no load will not damage these devices, however they may
not meet all specifications. In order to ensure the converter can work
reliably with high efficiency, please parallel a resistor on the output side
(The sum of the efficient power and resistor consumption power is not less
than 10%).
LMS78_03-0.5R
LMS78_05-0.5R
LMS78_09-0.5R
LMS78_12-0.5R
LMS78_15-0.5R
10μF/50V
10μF/50V
10μF/50V
10μF/50V
10μF/50V
22μF/10V
22μF/10V
22μF/16V
22μF/25V
22μF/25V
Page 2 of 3
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LMS78_0.5R – Rev. 2020-2.6
Specifications subject to change without notice.
LMS78_0.5R Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Typical application circuit
To reduce the output ripple furtherly, it is suggested to connect a “LC” filter
at the output terminal, and recommended value of L is 10μH-47μH.
EMC solution-recommended circuit
Part 1 in the Fig. 5 is for EMS test, part 2 is for EMI filtering; parts
can be added based on actual requirement.
and
FUSE
MOV
LDM1
82μH
C0
C1/C2
C5
LDM2
12μH
Selected based on the
actual input current
from the customer
S10K35
680μF /50V
Refer to table above
4.7μF /50V
Mechanical dimension and footprint
Page 3 of 3
LMS78_0.5R – Rev. 2020-2.6
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号:
LMS8117ADT-3.3/NOPB
IC VREG 3.3 V FIXED POSITIVE LDO REGULATOR, 1.25 V DROPOUT, PSSO2, TO-252, 3 PIN, Fixed Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明