GLS85LP0512P-S-I-LBTE [GREENLIANT]

Industrial Grade PATA NANDrive;


型号：	GLS85LP0512P-S-I-LBTE
厂家：	Greenliant
描述：	Industrial Grade PATA NANDrive
文件：	总8页 (文件大小：122K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

Features

• Industry Standard ATA / IDE Bus Interface

• Expanded Data Protection

–

Host Interface: 16-bit access

–

WP#/PD# pin configurable by firmware for

prevention of data overwrites

Data security through user-selectable

protection zones

Supports 48-bit address feature set

Supports up to PIO Mode-6 ¹⁾

Supports up to Multi-Word DMA Mode-4 ²⁾

Supports up to Ultra DMA Mode-6

Security Erase feature

• 20-Byte Unique ID for Enhanced Security

• Performance

–

Factory pre-programmed 10-Byte unique ID

–

Sequential data read: Up to 50 MByte/sec*

–

User-programmable 10-Byte ID

–

Sequential data write: Up to 35 MByte/sec*

* measured using 128 Kbyte transfer size

• Integrated Voltage Detector

• Power Management

–

Prevents inadvertent Write operations due to

unexpected power-down or brownout

–

3.3V power supply

–

Immediate disabling of unused circuitry

without host intervention

Zero wake-up latency

• NAND Configuration

–

1 bit per cell (SLC)

–

Excellent endurance and data retention

• Power Specification

• Operating Temperature Range

Industrial: -40°C to 85°C

• 91-ball BGA and LBGA Packages

–

Active mode

–

8GB: 100mA (typical)

4GB: 80mA (typical)

512MB/2GB: 60mA (typical)

Sleep mode: 500µA (typical)

–

2GB, 4GB, 8GB:14.0mm x 24.0mm x 1.90mm,

1.0mm ball pitch, FTE

–

512MB: 12.0mm x 24.0mm x 1.40mm,

1.0mm ball pitch, LBTE

• Supports SMART Commands

• Robust Built-in ECC

• All Devices are RoHS Compliant

Product Description

The GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™ devices (referred

to as “PATA NANDrive” in this factsheet) are fully

integrated, embedded solid state drives. They

combine an integrated ATA controller and 512 MBytes,

2 GBytes, 4 GBytes or 8 GBytes of NAND flash

memory in a multi-chip package. These products are

ideal for embedded and portable applications that

require smaller form factor and more reliable data

storage.

The integrated NAND flash controller with built-in

advanced

NAND

management

firmware

communicates with the host through the standard ATA

protocol. It does not require any additional or

proprietary software such as the Flash File System

(FFS) and Memory Technology Driver (MTD).

PATA NANDrive provides a WP#/PD# pin to protect

critical information stored in the flash media from

unauthorized overwrites. PATA NANDrive is pre-

programmed with a 10-Byte unique serial ID and has

the option of programming an additional 10-Byte serial

ID for even greater system security.

ATA-based solid state mass storage technology is

widely used in GPS and telematics, in-vehicle

infotainment, portable and industrial computers,

handheld data collection scanners, point-of-sale

terminals, networking and telecommunications

equipment, robotics, audio and video recorders,

monitoring devices and set-top boxes.

PATA NANDrive’s advanced NAND management

technology enhances data security, improves

endurance and accurately predicts the remaining

lifespan of the NAND flash devices. This innovative

technology combines robust error correction

capabilities with advanced wear-leveling algorithms

and bad block management to significantly extend the

life of the product.

PATA NANDrive supports standard ATA/IDE protocol

with up to PIO Mode-6¹⁾, Multi-Word DMA Mode-4²⁾

and Ultra DMA Mode-6 interface. The PATA

NANDrive device provides complete IDE hard disk

drive functionality and compatibility in a 14mm x

24mm BGA package or a 12mm x 24mm LBGA

package for easy, space saving mounting to a system

motherboard. These products surpass traditional

storage in their small size, security, reliability,

ruggedness and low power consumption.

1) PATA NANDrive is capable of supporting PIO Mode-6,

but Identify-Drive information report will show PIO Mode-4

2) PATA NANDrive is capable of supporting Multi-Word

DMA Mode-4, but Identify-Drive information report will

show MWDMA Mode-2

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

1.0 GENERAL DESCRIPTION

Each PATA NANDrive contains an integrated PATA NAND flash memory controller and NAND flash die in a BGA

or LBGA package. Refer to Figure 2-1 for the PATA NANDrive block diagram.

1.1 Optimized PATA NANDrive

1.1.5 Error Correction Code (ECC)

The heart of PATA NANDrive is the PATA NAND flash

High performance is achieved through optimized

hardware error detection and correction.

memory controller, which translates standard PATA

signals into flash media data and control signals. The

following components contribute to PATA NANDrive’s

operation.

1.1.6 Serial Communication Interface (SCI)

The Serial Communication Interface (SCI) is designed

for error reporting. During the product development

stage, it is recommended to provide the SCI port on

the PCB to aid in design validation.

1.1.1 Microcontroller Unit (MCU)

The MCU transfers the ATA/IDE commands into data

and control signals required for flash media operation.

1.1.2 Internal Direct Memory Access (DMA)

1.1.7 Multi-tasking Interface

PATA NANDrive uses internal DMA allowing instant

data transfer from/to buffer to/from flash media. This

implementation eliminates microcontroller overhead

associated with the traditional, firmware-based

approach, thereby increasing the data transfer rate.

The multi-tasking interface enables fast, sustained

write performance by allowing concurrent Read,

Program and Erase operations to multiple flash media.

1.2 SMT Reflow Consideration

The PATA NANDrive family utilizes standard NAND

flash for data storage. Because the high temperature

in a surface-mount soldering reflow process can alter

the content on NAND flash, do not program PATA

NANDrive before the reflow process.

1.1.3 Power Management Unit (PMU)

The PMU controls the power consumption of PATA

NANDrive. The PMU dramatically reduces the power

consumption of PATA NANDrive by putting the part of

the circuitry that is not in operation into sleep mode.

1.3 Advanced NAND Management

The Flash File System handles inadvertent power

interrupts and has auto-recovery capability to ensure

PATA NANDrive’s data integrity. For regular power

PATA NANDrive’s integrated controller uses

advanced wear-leveling algorithms to substantially

increase the longevity of NAND flash media. Wear

caused by data writes is evenly distributed in all or

select blocks in the device that prevents “hot spots” in

locations that are programmed and erased extensively.

This effective wear-leveling technique results in

optimized device endurance, enhanced data retention

and higher reliability required by long-life applications.

management,

the

host

must

send

IDLE_IMMEDIATE command and wait for command

ready before powering down PATA NANDrive.

1.1.4 Embedded Flash File System

The embedded flash file system is an integral part of

PATA NANDrive. It contains MCU firmware that

performs the following tasks:

1. Translates host side signals into flash media

writes and reads

2. Provides flash media wear leveling to spread

the flash writes across all memory address

space to increase the longevity of flash media

3. Keeps track of data file structures

4. Manages system security for the selected

protection zones

5. Stores the data in flash media upon completion

of a Write command (PATA NANDrive does not

perform Post-Write operations, except for when

the write cache is enabled)

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

2.0 FUNCTIONAL BLOCKS

Figure 2-1: PATA NANDrive Block Diagram

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

3.0 PRODUCT ORDERING INFORMATION

GLS 85 LP 1 xxxP - S - I - FTE - NDxxx

XX XX X XXXX - X - X - XXXX - XXXXX

Ordering Code ³⁾

NDxxx = NANDrive Revision

EDxxx = Evaluation Board Revision

Environmental Attribute

E = non-Pb solder (RoHS Compliant)

Package Modifier

T = 88 ball positions (nearest letter code

to total ball count of 91)

Package Type

F = BGA (max. package height 1.90mm)

LB = LBGA (max. package height 1.40mm)

Operating Temperature

I = Industrial: -40°C to +85°C

NAND configuration

S = 1 bit per cell

Product Generation

P = Generation

Capacity

512 = 512 MByte

002 = 2 GByte

004 = 4 GByte

008 = 8 GByte

MByte or GByte Designator

0 = MByte, 1 = GByte

Interface

P= Parallel ATA/IDE Interface

Voltage

L = 3.3V

Product Series

85 = NANDrive

For legacy NANDrive products, no ordering code is required. Note that the top side marking on the package typically does

not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC (custom specification) which is required by the end-

customer to be marked on the device.

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

Valid Combinations

Valid product combinations are those that are in the mass production or will be in the mass production. Consult

your Greenliant sales representative to confirm availability of the valid combinations and to determine availability

of new product combinations.

Table 3-1: PATA NANDrive Product Valid Ordering Numbers

Capacity Operating Temperature

Part Number

Package

512MB Industrial (-40°C to 85°C) GLS85LP0512P-S-I-LBTE

GLS85LP1002P-S-I-FTE

LBTE, 12x24x1.40mm

FTE, 14x24x1.90mm

2GB

4GB

8GB

Industrial (-40°C to 85°C) GLS85LP1002P-S-I-FTE-ND001

GLS85LP1002P-S-I-FTE-ND004

GLS85LP1004P-S-I-FTE

Industrial (-40°C to 85°C) GLS85LP1004P-S-I-FTE-ND001

GLS85LP1004P-S-I-FTE-ND004

GLS85LP1008P-S-I-FTE

GLS85LP1008P-S-I-FTE-ND001

GLS85LP1008P-S-I-FTE-ND004

Industrial (-40°C to 85°C)

Table 3-2: PATA NANDrive Evaluation Board Valid Ordering Numbers

Capacity Operating Temperature

Part Number

Form Factor

GLS85LP0512P-S-I-40CN-K

GLS85LP0512P-S-I-44CN-K

GLS85LP1002P-S-I-40CN-K

GLS85LP1002P-S-I-44CN-K

GLS85LP1002P-S-I-40CN-ED001

GLS85LP1002P-S-I-40CN-ED004

GLS85LP1004P-S-I-40CN-K

GLS85LP1004P-S-I-44CN-K

GLS85LP1004P-S-I-40CN-ED001

GLS85LP1004P-S-I-40CN-ED004

GLS85LP1008P-S-I-40CN-K

GLS85LP1008P-S-I-44CN-K

GLS85LP1008P-S-I-40CN-ED001

GLS85LP1008P-S-I-40CN-ED004

Module with 40-pin ATA connector

Module with 44-pin ATA connector

Module with 40-pin ATA connector

Module with 44-pin ATA connector

Module with 40-pin ATA connector

Module with 44-pin ATA connector

Module with 40-pin ATA connector

Module with 44-pin ATA connector

Module with 40-pin ATA connector

512MB Industrial (-40°C to 85°C)

2GB

4GB

8GB

Industrial (-40°C to 85°C)

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

3.1 Package Diagrams

3.1.1 FTE Package

Figure 3-1: PATA NANDrive 91-Ball, Ball Grid Array (BGA) Greenliant Package Code: FTE

Note:

All linear dimensions are in millimeters.

Un-tolerance dimensions are nominal target values.

Co-planarity: 0.15 mm.

Ball opening size is 0.40 mm (± 0.05 mm).

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

3.1.2 LBTE Package

Figure 3-2: PATA NANDrive 91-Ball, Ball Grid Array (LBGA) Greenliant Package Code: LBTE

Note:

All linear dimensions are in millimeters.

Un-tolerance dimensions are nominal target values.

Co-planarity: 0.15 mm.

Ball opening size is 0.40 mm (± 0.05 mm).

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P / 1002P / 1004P / 1008P

Industrial Grade PATA NANDrive™

Factsheet 03.100

June 2019

Revision History

Revision

Description

Date

01.000

Initial release of datasheet

June 15, 2011

Added Total program/erase cycle count

02.000

June 1, 2012

Updated Power specification, Initialization time and Purge time

Updated first page and Section 1.0; Removed Pin Assignments and

Updated section numbering; Placed Valid Combinations into table

format and Updated Section 3.0

03.000

03.100

February 19, 2014

June 28, 2019

Added part numbers to Tables 3-1, 3-2

Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant. All

other trademarks and registered trademarks are the property of their respective owners.

Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable

capacity may be less.

Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant

Terms and Conditions of Sale.

www.greenliant.com

These specifications are subject to change without notice.

06/28/2019

S71431-F

GLS85LP0512P-S-I-LBTE [GREENLIANT]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E