GLS85LS1016G-S-I-1S-ED111 [GREENLIANT]
Industrial Grade SATA NANDrive EX Series;
| 型号： | GLS85LS1016G-S-I-1S-ED111 |
| 厂家： | 
Greenliant |
| 描述： | Industrial Grade SATA NANDrive EX Series |
| 文件： | 总7页 (文件大小：150K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
Features
• Expanded Data Protection
• Industry Standard Serial ATA (SATA) Host
–
Added data security through user-selectable
protection zones
Interface
–
–
–
–
SATA 1.5Gb/s, 3Gb/s and 6Gb/s
SATA Revision 3.2
ATA/ATAPI-8 compliant
–
Secure Erase (data sanitization)
• 20-Byte Serial Number
Supports 48-bit address feature set
–
–
Factory pre-programmed 10-Byte unique ID
User-programmable 10-Byte ID
• Performance
• Supports SMART and TRIM Commands
• Robust Built-in ECC
• Thermal Throttling
–
–
Sequential data read: Up to 470 MByte/sec*
Sequential data write: Up to 340 MByte/sec*
* 128 KByte transfer size tested in VDBench on Linux
• Power Management
• Native Command Queuing (NCQ)
–
–
–
3.3V and 1.0V power supply
Host initialized power management (HIPM)
Device initialized power management (DIPM)
–
Up to 32 commands
• NAND Configuration
–
–
1 bit per cell (SLC)
Designed with Greenliant’s advanced
EnduroSLC™ Technology
Power Specifications1)
•
–
Active mode:
128GB: Up to 2180mW
64GB: Up to 1800mW
32GB: Up to 1980mW
16GB: Up to 1540mW
8GB: Up to 1200mW
4GB: Up to 1200mW
Idle / Standby mode: <355mW (typical)
DevSleep mode: <70mW (typical)
• High Endurance
–
–
GLS85LS1xxxG: 50K P/E cycles
GLS85LS1xxxQ: 100K P/E cycles
•
Operating Temperature Range
Industrial: -40°C to 85°C
• FBGA package
14.0 mm x 24.0 mm x 1.40 mm, 145-ball,
1.0 mm ball pitch, LBJE
–
–
–
–
• All Devices are RoHS Compliant
Product Description
The GLS85LS1xxxG / GLS85LS1xxxQ Industrial
Grade SATA NANDrive™ EX Series devices (referred
to as “SATA NANDrive” in this factsheet) are fully
integrated solid state drives. They combine an
advanced Greenliant NAND controller and 4, 8, 16, 32,
64 or 128 GBytes of NAND flash in a multi-chip
package. These products are ideal for embedded and
portable applications that require a smaller form factor
and reliable data storage.
The integrated NAND flash controller with built-in
advanced
NAND
management
firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA-interface solid state mass storage technology is
widely used in industrial PCs, single board computers,
servers, networking appliances, HMI and digital
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
signage
displays,
test
and
measurement
instrumentation, multi-functional printers, robotics, and
video equipment and security systems.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
SATA NANDrive devices are offered in a 145-ball BGA,
1 mm ball pitch package.
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
1
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
1.0
GENERAL DESCRIPTION
Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete
NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram.
1.1.5 Error Correction Code (ECC)
1.1
Optimized SATA NANDrive
The ECC technology uses advanced algorithms to
detect and correct errors, ensuring data integrity and
extending the SSD lifespan.
The heart of SATA NANDrive is the SATA NAND
flash memory controller which translates standard
SATA signals into flash media data and control
signals. The following components contribute to
SATA NANDrive’s operation.
1.1.6 Serial Communication Interface (SCI)
The Serial Communication Interface (SCI) is
designed for error reporting. During the product
development stage, it is recommended to provide
the SCI port on the PCB to aid in design validation.
1.1.1 Microcontroller Unit (MCU)
The MCU translates SATA commands into data and
control signals required for flash media operation.
1.1.7 Multi-tasking Interface
1.1.2 Internal Direct Memory Access (DMA)
The multi-tasking interface enables fast, sequential
write performance by allowing concurrent Read,
Program and Erase operations to multiple flash
media.
SATA NANDrive uses internal DMA allowing instant
data transfer from/to buffer to/from flash media. This
implementation eliminates microcontroller overhead
associated with the traditional, firmware-based
approach, thereby increasing the data transfer rate.
1.2
SMT Reflow Consideration
1.1.3 Power Management Unit (PMU)
Preprogrammed NAND devices have temperature
limits due to data retention. The EnduroSLC™ SATA
NANDrive family uses high-grade SLC NAND flash
which can retain data in high temperature
environments. Using Greenliant’s recommended
reflow profile during production will help prevent
damage to the device and ensure better retention of
any preprogrammed data through the surface-mount
soldering process. See the relevant datasheet
section describing the recommended reflow
temperature limits.
The PMU controls the power consumption of SATA
NANDrive. The PMU dramatically reduces the power
consumption of SATA NANDrive by putting the part
of the circuitry that is not in operation into sleep
mode.
The Flash File System handles inadvertent power
interrupts and has auto-recovery capability to ensure
SATA NANDrive firmware integrity. For regular
power management, the host must send
a
STANDBY_IMMEDIATE (E0h), IDLE_IMMEDIATE
(E1h), STANDBY (E2h) or IDLE (E3h) command
and wait for the command-ready before powering
down SATA NANDrive.
1.3
Advanced NAND Management
SATA NANDrive’s integrated controller uses
advanced wear-leveling algorithms to substantially
increase the longevity of NAND flash media. Wear
caused by data writes is evenly distributed across all
or select blocks in the device to prevent “hot spots”
in locations that are programmed and erased
extensively. This effective wear-leveling technique
results in optimized device endurance, enhanced
data retention and higher reliability required by long-
life applications.
1.1.4 Embedded Flash File System
The embedded flash file system is an integral part of
SATA NANDrive. It contains MCU firmware that
performs the following tasks:
1. Translates host side signals into flash media
writes and reads
2. Provides flash media wear leveling to spread
the flash writes across all memory address
space to increase the longevity of flash media
3. Keeps track of data file structures
4. Manages system security for the selected
protection zones
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
2
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
2.0
FUNCTIONAL BLOCKS
Figure 2-1: SATA NANDrive Block Diagram
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
3
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
3.0
Product Ordering Information
GLS 85 LS 1 xxxQ - S - I - LBJE - NDxxx
XX XX X XXXX - X - X - XXXX - XXXXX
Ordering Code 1)
NDxxx = NANDrive Revision
EDxxx = Evaluation Board Revision
Environmental Attribute
E = non-Pb solder (RoHS Compliant)
Package Modifier
BJ = 145-ball positions
Package Type
L = LBGA
Operating Temperature
I = Industrial: -40°C to +85°C
NAND Configuration
S = 1 bit per cell
Product Generation
G, Q = Generation
Capacity
004 = 4 GByte
008 = 8 GByte
016 = 16 GByte
032 = 32 GByte
064 = 64 GByte
128 = 128 GByte
MByte or GByte Designator
0 = MByte
1 = GByte
Interface
S = SATA
Voltage
L = 3.3V
Product Family
85 = NANDrive
1) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC
(custom specification) which is required by the end-customer to be marked on the device.
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
4
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
Valid Combinations
Valid product combinations are those that are in the mass production, or will be in the mass production. Consult
your Greenliant sales representative to confirm availability of the valid combinations and to determine availability
of new product combinations.
Table 3-1: SATA NANDrive Product Valid Ordering Numbers
Capacity Operating Temperature
Part Number
Package
4GB
Industrial (-40°C to 85°C) GLS85LS1004G-S-I-LBJE-ND111
Industrial (-40°C to 85°C) GLS85LS1004Q-S-I-LBJE-ND115
Industrial (-40°C to 85°C) GLS85LS1008G-S-I-LBJE-ND111
Industrial (-40°C to 85°C) GLS85LS1008Q-S-I-LBJE-ND115
Industrial (-40°C to 85°C) GLS85LS1016G-S-I-LBJE-ND111
Industrial (-40°C to 85°C) GLS85LS1016Q-S-I-LBJE-ND115
Industrial (-40°C to 85°C) GLS85LS1032G-S-I-LBJE-ND111
Industrial (-40°C to 85°C) GLS85LS1032Q-S-I-LBJE-ND115
Industrial (-40°C to 85°C) GLS85LS1064G-S-I-LBJE-ND117
Industrial (-40°C to 85°C) GLS85LS1064Q-S-I-LBJE-ND116
Industrial (-40°C to 85°C) GLS85LS1128G-S-I-LBJE-ND117
Industrial (-40°C to 85°C) GLS85LS1128Q-S-I-LBJE-ND116
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
LBJE, 14x24x1.40mm
4GB
8GB
8GB
16GB
16GB
32GB
32GB
64GB
64GB
128GB
128GB
Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers
Capacity Operating Temperature Part Number
Form Factor
4GB
Industrial (-40°C to 85°C) GLS85LS1004G-S-I-1S-ED111
Industrial (-40°C to 85°C) GLS85LS1004Q-S-I-1S-ED115
Industrial (-40°C to 85°C) GLS85LS1008G-S-I-1S-ED111
Industrial (-40°C to 85°C) GLS85LS1008Q-S-I-1S-ED115
Industrial (-40°C to 85°C) GLS85LS1016G-S-I-1S-ED111
Industrial (-40°C to 85°C) GLS85LS1016Q-S-I-1S-ED115
Industrial (-40°C to 85°C) GLS85LS1032G-S-I-1S-ED111
Industrial (-40°C to 85°C) GLS85LS1032Q-S-I-1S-ED115
Industrial (-40°C to 85°C) GLS85LS1064G-S-I-1S-ED117
Industrial (-40°C to 85°C) GLS85LS1064Q-S-I-1S-ED116
Industrial (-40°C to 85°C) GLS85LS1128G-S-I-1S-ED117
Industrial (-40°C to 85°C) GLS85LS1128Q-S-I-1S-ED116
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
4GB
8GB
8GB
16GB
16GB
32GB
32GB
64GB
64GB
128GB
128GB
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
5
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
3.1
Package Diagram
TOP VIEW
11
10
9
8
7
6
5
4
3
2
1
14.0
+/- 0.1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA AB AC
24.0 ±0.1
A1
CORNER
BOTTOM VIEW
0.5 +/- 0.05
(145x)
14.0
3.0
1
2
3
4
5
6
1.0
8.0
7
8
9
10
11
1.0
E
A
B
C
D
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA AB AC
SIDE VIEW
1mm
DETAIL
Note: All linear dimensions are in millimeters.
Untoleranced dimensions are nominal target values.
Coplanarity: 0.15 mm.
0.40 ±0.05
Ball opening size is 0.40 mm (± 0.05 mm).
1.30 ± 0.10
0.15
SEATING PLANE
Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: LBJ
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
6
GLS85LS1xxxG / GLS85LS1xxxQ
Industrial Grade SATA NANDrive™ EX Series
Factsheet 01.000
July 2019
Revision History
Revision
Description
Date
01.000
Initial release as Factsheet
July 22, 2019
© 2019 Greenliant. All rights reserved.
Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant. All
other trademarks and registered trademarks are the property of their respective owners.
Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable
capacity may be less.
Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant
Terms and Conditions of Sale.
www.greenliant.com
These specifications are subject to change without notice.
© 2019 Greenliant
07/22/2019
S71457-01
7
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明