S9706_15 [HAMAMATSU]
Digital color sensor;
| 型号： | S9706_15 |
| 厂家： | 
HAMAMATSU CORPORATION |
| 描述： | Digital color sensor |
| 文件： | 总6页 (文件大小：311K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Digital color sensor
S9706
12-bit digital output
The S9706 is a digital color sensor sensitive to red (λ=615 nm), green (λ=540 nm) and blue (λ=465 nm) regions of the spectrum.
Detected signals are serially output as 12-bit digital data. Built-in three 12-bit registers allow simultaneous measurement of RGB
three colors. Sensitivity level is adjustable in two steps to cover a wide photometric range.
Features
Applications
12-bit digital output
Display color adjustment
Simultaneous measurement of RGB three colors
2-step sensitivity switching (sensitivity ratio of 1 : 9)
Low voltage (3.3 V) operation
Various applications involving color detection
CMOS monolithic photo IC
No external components required
Feature
Feature
12-bit digital output
Simultaneous measurement of RGB three colors
01
02
Light signals detected by the photodiode are amplified and convert-
ed into 12-bit digital signals. An amplifier is also formed for each of
the RGB photodiode elements arrayed in the mosaic pattern, allow-
ing simultaneous accurate measurement of the RGB components of
incident light.
The photodiode consists of 9 × 9 elements arrayed in a mosaic
pattern. Each element has an on-chip filter that it sensitive to one
color of light, either red (λp=615 nm), green (λp=540 nm) or blue
(λp=465 nm).
Block diagram
Spectral response
(Typ. Ta=25 °C)
1.0
Range
Vdd
Green
I/F
Register
0.8
0.6
0.4
0.2
0
Blue
R
Red
Serial
converter
I/F
I/F
Dout
Register
Register
G
B
CK
Timing
circuit
Gate
GND
400
500
700
800
300
600
Wavelength (nm)
KPICC0110EB
KPICB0089EA
This product does not support lead-free soldering. Solder it by hand.
1
www.hamamatsu.com
Digital color sensor
S9706
Feature
2-step sensitivity switching
03
To enable measurement over a wide range of illuminance, the photodiode sensitivity can be selected from two setting modes (high sensitivity
mode and low sensitivity mode). The photodiode photosensitive area used to detect light differs depending on which sensitivity mode is selected
(high sensitivity mode: 9 × 9 elements, low sensitivity mode: 3 × 3 elements in center).
Sensitivity setting
Details of photosensitive area (unit: μm)
132
Range
High
Low
Mode
High sensitivity
Low sensitivity
Effective photosensitive area
9 × 9 elements
*
110
Pin no. 1 side
Pin no. 6 side
3 × 3 elements
* The photosensitive area of S9706 consists of 9 × 9 elements in a mosaic
pattern.
3 × 3 elements in
low sensitivity mode
The effective photosensitive area changes depending on which sensitivity
mode is used, “high” or “low”, as explained below.
· High sensitivity mode: 9 × 9 elements
9 × 9 elements in
high sensitivity mode
· Low sensitivity mode:3 × 3 elements in center
Pin no. 3 side
Pin no. 4 side
Note: Spaceing between elements is light-shielded.
KPICC0124EB
Absolute maximum ratings
Parameter
Supply voltage
Load current
Power dissipation
Operating temperature
Storage temperature
Symbol
Vdd Ta=25 °C
Io
P
Topr
Tstg
Condition
Value
-0.3 to 6
±10
100
-20 to +85
-20 to +85
Unit
V
mA
mW
°C
Ta=25 °C
Ta=25 °C
°C
Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the
product within the absolute maximum ratings.
2
Digital color sensor
S9706
Electrical and optical characteristics
(Ta=25 °C, Vdd=5 V, Tg=100 ms, A light source, unless otherwise noted)
Parameter
Photosensitive area size
Effective photosensitive area
Symbol
Condition
Min.
-
-
Typ.
Max.
-
-
Unit
mm
mm2
-
-
All elements (9 9 elements)
1.2 1.2
×
×
Per 1 color, High range
0.32
Blue
Green
Red
Blue
Green
Red
-
-
-
-
-
-
400 to 540
480 to 600
590 to 720
-
-
-
-
-
-
Spectral response range
λ
nm
nm
465
540
615
Peak sensitivity wavelength
λp
Supply voltage
Current consumption
Vdd
Idd
Sbl
Sgl
Srl
Sbh
Sgh
Srh
Ibl
Igl
Irl
Ibh
Igh
Irh
3.0
-
0.15
0.32
0.45
1.3
2.8
4.0
-
-
-
-
-
-
-
-
5
0.21
0.45
0.64
1.9
4.1
5.8
-
-
-
-
-
-
-
-
5.5
10
0.27
0.59
0.83
2.5
5.4
7.6
240
110
78
26
12
8.6
1
V
mA
Dark state, no load
Blue, Low range
Green, Low range
Red, Low range
Blue, High range
Green, High range
Red, High range
Blue, Low range
Green, Low range
Red, Low range
Blue, High range
Green, High range
Red, High range
Photosensitivity
LSB/lx
Incident light power
(Conversion value in A light
source)
klx
Dark output
Input high level
Dark Tg=0.5 s
Vih
LSB
V
Vdd 0.82
-
×
Input low level
Vil
-
4.5
-
-
-
-
Vdd 0.18
V
V
V
-
×
High level output voltage
Low level output voltage
Integration time
Voh Ioh=-0.5 mA
Vol
Tg
-
0.5
Iol=0.5 mA
Refer to “Output vs. illuminance”
t1
t2
t3
t4
t5
tck
tw
4
3
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
μs
μs
μs
μs
μs
ns
ns
ns
Hold time
2000
3
500
200
200
Readout clock period
Readout pulse width (positive)
Readout pulse width (negative)
tck-tw
3
Digital color sensor
S9706
Output vs. illuminance
Low range
High range
(Typ. A light source, Green)
(Typ. A light source, Green)
10000
1000
100
10
10000
Tg=100 s
Tg=100 s
1000
100
10
10 s
10 s
1 s
1 s
100 ms
100 ms
10 ms
10 ms
1 ms
1 ms
100 μs
100 μs
10 μs
10 μs
1
0.1
1
0.01
1
10
1000 10000 100000 1000000
1
10
1000 10000 100000
100
0.1
100
Illuminance (lx)
Illuminance (lx)
KPICB0099EA
KPICB0100EA
Timing chart
Range
t5
t3
Gate
t4
tg
12 pulses
····
12 pulses
····
12 pulses
····
CK
t1
t2
tck
tw
Red output (12-bit output)
····
Green output (12-bit output)
····
Blue output (12-bit output)
····
MSB
Dout
LSB
MSB LSB
MSB LSB
Operating sequence
(1) Set the Gate terminal and CK terminal to “Low”.
(2) Select the desired sensitivity with the Range terminal.
(3) Set the Gate terminal from “Low” to “High”, to start integrating the light intensity.
(4) After the desired integration time (tg) has passed, set the Gate terminal from “High” to “Low” to end the light intensity integration.
(5) Measurement data is output from the Dout terminal by inputting 36 CK pulses to the CK terminal.
Note 1: A total of 36 CK pulses are required to read out 3-color measurement data. Red data is output by the first 12 pulses,
green data by the next 12 pulses, and blue data by the last 12 pulses. Measurement data is output from the LSB side.
Note 2: Measurement data changes at the CK pulse rising edge.
Note 3: Do not switch the Range terminal during integration time (tg).
KPICC0115EB
4
Digital color sensor
S9706
Dimensional outline (unit: mm)
4.1 0.2
(Including burr)
Visual-compensated filter
(2.6 × 3.9 × 0.75 t)
Photosensitive area
(1.2 × 1.2)
2.6
1.5 0.4
1.5 0.4
4.0*
7.0 0.3
0.7 0.3
0.7 0.3
(2 ×) 10°
Dout
Vdd
Tolerance unless otherwise
noted: 0.1, 2°
GND
Range
CK
Chip position accuracy with
respect to the package
dimensions marked *
X, Y≤ 0.2
(2 ×) 5°
ϕ2.0 depth 0.15 max.
Gate
θ≤ 3°
Lead surface finish: silver plating
Packaging: stick (50 pcs/stick)
KPICA0060EE
Note: If excessive vibration is continuously applied to the glass filter, there is a risk that the filter may come off, so secure the glass
filter with a holder.
5
Digital color sensor
S9706
Line-up of RGB color sensors
Peak sensitivity
Photosensitive area
Package
(mm)
wavelength
Type no.
Type
Photosensitivity
Photo
(mm)
(nm)
4 × 4.8 × 1.8t
6 pin
0.18 (A/W) [λ=460 nm]
0.23 (A/W) [λ=540 nm]
0.16 (A/W) [λ=620 nm]
0.18 (A/W) [λ=460 nm]
0.23 (A/W) [λ=540 nm]
0.16 (A/W) [λ=620 nm]
0.2 (A/W) [λ=460 nm]
0.23 (A/W) [λ=540 nm]
0.17 (A/W) [λ=620 nm]
0.21 (A/W) [λ=460 nm]
0.25 (A/W) [λ=540 nm]
0.45 (A/W) [λ=640 nm]
B
460
540
620
460
540
620
460
540
620
B
G
R
B
G
R
B
G
R
B
G
R
S9032-02
Photodiode
ϕ2.0
G
R
B
G
R
B
G
R
(filter 0.75t)
3 × 4 × 1.3t
4 pin
S9702
Photodiode
Photodiode
Photodiode
1.0 × 1.0
1.0 × 1.0
1.0 × 1.0
1.2 × 1.2
1.2 × 1.2
(filter 0.75t)
3 × 1.6 × 1.0t
COB
(on-chip filter)
3 × 1.6 × 1.0t
COB
(on-chip filter)
S10917-35GT
S10942-01CT
S9706
*
4 × 4.8 × 1.8t
6 pin
B
G
R
465
540
615
B
G
R
B
G
R
B
G
R
IR
B
G
R
B
G
R
0.21 (LSB/lx)
0.45 (LSB/lx)
0.64 (LSB/lx)
0.3 (LSB/lx)
1.9 (LSB/lx)
4.1 (LSB/lx)
5.8 (LSB/lx)
Digital
photo IC
(filter 0.75t)
3.43 × 3.8 × 1.6t
COB
B
2.6 (LSB/lx)
Digital
photo IC
G
R
B
G
R
IR
B
G
R
IR
S11012-01CR
*
0.6 (LSB/lx)
1.4 (LSB/lx)
5.3 (LSB/lx)
(on-chip filter)
12.9 (LSB/lx)
44.8 (count/lx)
85.0 (count/lx)
117.0 (count/lx)
30.0 (count/lx)
31.7 (count/lx)
76.2 (count/lx)
94.5 (count/lx)
15.3 (count/lx)
I2C
compatible
color
B
G
R
460
530
615
4.4 (count/lx)
8.3 (count/lx)
11.2 (count/lx)
3.0 (count/lx)
3.35 (count/lx)
7.61 (count/lx)
9.48 (count/lx)
1.66 (count/lx)
3 × 4.2 ×1.3t
10 pin
(on-chip filter)
S11059-02DT
/-03DS
0.56 × 1.22
1.22 × 0.56
sensor
IR 855
I2C
compatible
color
B
G
R
460
530
615
1.68 × 1.18 ×0.58t
WL-CSP
(on-chip filter)
S11059-01WT
sensor
IR 855
IR
* Refer to the spectral response of each product’s datasheet.
Related information
www.hamamatsu.com/sp/ssd/doc_en.html
Precautions
∙ Disclaimer
∙ Metal, ceramic, plastic package products
∙ Surface mount type products
Information described in this material is current as of August, 2015.
Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the
information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always
contact us for the delivery specification sheet to check the latest specifications.
The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that
one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use.
Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Solid State Division
1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741
China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866
6
Cat. No. KPIC1060E13 Aug. 2015 DN
相关型号：
©2020 ICPDF网 联系我们和版权申明