HMC433_06 [HITTITE]
SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz; SMT砷化镓HBT MMIC除以4 ， DC - 8.0 GHz的
| 型号： | HMC433_06 |
| 厂家： | 
HITTITE MICROWAVE CORPORATION |
| 描述： | SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz |
| 文件： | 总6页 (文件大小：309K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
5
Typical Applications
Features
Prescaler for DC to C Band PLL Applications:
• UNII, Point-to-Point & VSAT Radios
• 802.11a & HiperLAN WLAN
• Fiber Optic
Ultra Low SSB Phase Noise: -150 dBc/Hz
Single-Ended I/O’s
Output Power: -2 to -3.5 dBm
Single DC Supply: +3V @ 53 mA
9 mm2 Ultra Small Package: SOT26
• Cellular / 3G Infrastructure
General Description
Functional Diagram
The HMC433 & HMC433E are low noise Divide-by-4
Static Dividers utilizing InGaP GaAs HBT technology
in ultra small surface mount SOT26 plastic packages.
This device operates from DC (with a square wave
input) to 8.0 GHz input frequency with a single +3.0V
DC supply. Single-ended inputs and outputs reduce
component count and cost. The low additive SSB
phase noise of -150 dBc/Hz at 100 kHz offset helps
the user maintain good system noise performance.
Electrical Specifications, TA = +25° C, 50 Ohm System, Vcc= +3V
Parameter
Maximum Input Frequency
Minimum Input Frequency
Conditions
Min.
8
Typ.
8.5
Max.
Units
GHz
GHz
Sine Wave Input. [1]
0.2
Fin= 1 to 6 GHz
Fin= 6 to 8 GHz
-12
-3
-15
-7
+12
+10
dBm
dBm
Input Power Range
Output Power
Fin= 4 GHz
Fin= 8 GHz
-5.0
-6.5
-2.0
-3.5
dBm
dBm
Reverse Leakage
RF Output Terminated, Fin= 4 GHz, Pin= 0 dBm
Pin= 0 dBm, Fin= 4 GHz
-25
-150
120
53
dBm
dBc/Hz
ps
SSB Phase Noise (100 kHz offset)
Output Transition Time
Supply Current (Icc)
Pin= 0 dBm, Fout= 882 MHz
Vcc= +3.0V
mA
1. Divider will operate down to DC for square-wave input signal.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 72
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
5
Input Sensitivity Window, T= 25 °C
Input Sensitivity Window vs. Temperature
20
15
10
5
20
15
10
5
Min Pin +25 C
Max Pin +25 C
Recommended
Operating Window
0
0
-5
Min Pin -40 C
Max Pin -40 C
Min Pin +85 C
Max Pin +85 C
-5
-10
-15
-20
-10
-15
-20
0
1
2
3
4
5
6
7
8
9
9
9
10
10
10
0
1
2
3
4
5
6
7
8
9
10
107
10
INPUT FREQUENCY (GHz)
INPUT FREQUENCY (GHz)
SSB Phase Noise
Performance, Pin= 0 dBm, T= 25 °C
Output Power vs. Temperature
0
0
-20
-2
-40
-60
-4
-80
+25 C
-6
-8
-40 C
-100
-120
-140
-160
+85 C
-10
0
1
2
3
4
5
6
7
8
102
103
104
105
106
INPUT FREQUENCY (GHz)
OFFSET FREQUENCY (Hz)
Output Harmonic
Content, Pin= 0 dBm, T= 25 °C
Reverse Leakage, Pin= 0 dBm, T= 25 °C
0
-10
-20
-30
0
-10
-20
-30
-40
-50
-60
Pfeedthru
2nd Harmonic
3rd Harmonic
-40
-50
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
9
INPUT FREQUENCY (GHz)
INPUT FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 73
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
Output Voltage Waveform,
Pin= 0 dBm, Fout= 882 MHz, T= 25 °C
5
Absolute Maximum Ratings
300
RF Input (Vcc= +3.0V)
+15 dBm
250
Vcc
+3.5V
200
Maximum Channel Temperature
135 °C
150
100
Continuous Pdiss (T=85 °C)
(derate 5mW/°C above 85 °C)
250mW
50
0
Storage Temperature
Operating Temperature
ESD Sensitivity (HBM)
-65 to +150 °C
-40 to +85 °C
Class 1A
-50
-100
-150
-200
DC blocking capacitors are required at RF input and RF output ports.
Choose value for lowest frequency of operation.
-250
-300
23 23.2 23.4 23.6 23.8 24 24.2 24.4 24.6 24.8 25
TIME (nS)
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Typical Supply Current vs. Vcc
Vcc (V)
Icc (mA)
2.70
42
3.0
53
3.30
63
Outline Drawing
Note: Divider will operate over full voltage range shown above
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
MSL1 [1]
Package Marking [3]
H433
XXXX
HMC433
Low Stress Injection Molded Plastic
Sn/Pb Solder
433E
XXXX
MSL1 [2]
HMC433E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 74
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
5
Pin Description
Pin Number
Function
Description
Interface Schematic
1, 4
N/C
No Connection
2
3
GND
Pin must connect ro RF/DC ground.
RF input must be DC blocked.
IN
5
6
Vcc
Supply voltage 3V 0.3V.
OUT
Divided output must be DC blocked.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 75
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
5
Evaluation PCB
Note: Line lengths on pins 1 & 4
(N/C) are not necessary.
List of Materials for Evaluation PCB 105675 [1]
The circuit board used in the final application should
useRFcircuitdesigntechniques. Signallinesshould
have 50 ohm impedance while the package ground
leads should be connected directly to the ground
plane similar to that shown. A sufficient number of
via holes should be used to connect the top and
bottom ground planes. The evaluation circuit board
shown is available from Hittite upon request.
Item
Description
J1 - J2
J3 - J4
C1 - C2
C3
PCB Mount SMA RF Connector
DC Pin
100 pF Capacitor, 0402 Pkg.
1000 pF Capacitor, 0402 Pkg.
10 μF Tantalum Capacitor, 1206 Pkg.
HMC433 / HMC433E Divide-by-4
105199 Eval Board
C4
U1
[2]
PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 76
HMC433 / 433E
v02.0705
SMT GaAs HBT MMIC
DIVIDE-BY-4, DC - 8.0 GHz
5
Application Circuit
Note:
DC blocking capacitor values (C1, C2) and DC decoupling capacitor
values (C3, C4) are chosen for lowest frequency of operation.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 77
相关型号：
HMC434ETR
Prescaler, 434 Series, 1-Func, GAAS, PDSO6, ROHS COMPLIANT, PLASTIC, SOT-26, 6 PIN
HITTITE
HMC435AMS8G
Diversity Switch, 0MHz Min, 4000MHz Max, 1.8dB Insertion Loss-Max, ULTRA SMALL, PLASTIC, SMT, MSOP-86, 8 PIN
HITTITE
©2020 ICPDF网 联系我们和版权申明