HMC7447 [HITTITE]
Analog Circuit,;
| 型号： | HMC7447 |
| 厂家： | 
HITTITE MICROWAVE CORPORATION |
| 描述： | Analog Circuit, |
| 文件： | 总8页 (文件大小：292K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Features
Typical Applications
The HMC7447 monitors Tx Output Power for:
• E-Band Communications Systems
• Test Equipment & Sensors
Frequency: 71 - 86 GHz
Input Power Range: -0.5 to +23.5 dBm
Dynamic Range: 24 dB
• General Purpose RF Power Detection
Insertion Loss: 0.45 dB
I/Os Matched to 50 Ohms
Die Size: 0.87 x 1.22 x 0.1 mm
Functional Diagram
General Description
The HMC7447 is a high performance E-Band MMIC
power detector designed to operate over the 71 to 86
GHz frequency range. The power detector provides a
linear output voltage over a -0.5 to +23.5 dBm input
power range with low insertion loss of 0.45 dB and
typical input return loss of only 19.5 dB. Ideal for
monitoring transmitter operation or enabling closed-
loop transmitter output power, the detector exhibits
excellent sensitivity and flat frequency response of
+/- 0.2 dB over the 71 to 76 GHz band and the 81
to 86 GHz band. The HMC7447 power detector also
provides excellent repeatabillity and performance over
varying temperature and output load variations. It may
be interfaced to an op-amp circuit to achieve a slope of
20 mV/dB at the minimum detector input power level.
All data is taken with the chip in a 50 Ohm test fixture
connected via a 0.025 mm (1mil) diameter double wire
bonds of 0.2 mm (8 mils) maximum length.
Electrical Specifications, TA = +25°C
Parameter
Min.
-0.5
Typ.
Max.
23.5
Units
Frequency Range
Input Power Range
Dynamic Range
Insertion Loss
71 - 86
GHz
dBm
dB
24
0.45
dB
Output Voltage
0.048
20
1.45
V
[1]
mV/dB
dB
Minimum Sensitivity
Input Return Loss
Output Return loss
19.5
22
dB
[2]
0.2
dB
Detector Output Flatness Across Frequency
[1] After external OpAmp of Gain = 6dB.
[2] Typical flatness 0.2 dB (71 - 76) GHz and 0.2 dB (81 - 86)GHz.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
1
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Insertion Loss vs. Temperature
Input Return Loss vs. Temperature
2
0
-5
1
-10
-15
-20
-25
-30
-35
-40
0
-1
-2
-3
70
72
74
76
78
80
82
84
86
71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
FREQUENCY (GHz)
FREQUENCY (GHz)
+85 C
+25 C
-55 C
+25 C
+85 C
-55 C
Detector Voltage vs. Temperature,
Frequency = 71 GHz
10
Output Return Loss vs. Temperature
0
-5
-10
-15
-20
-25
-30
-35
-40
1
0.1
0.01
0.001
-12 -9 -6 -3
0
3
6
9
12 15 18 21 24
70
72
74
76
78
80
82
84
86
OUTPUT POWER (dBm)
FREQUENCY (GHz)
+85 C
+25 C
+85 C
-55 C
+25 C
-55 C
Detector Voltage vs. Temperature,
Detector Voltage vs. Temperature,
Frequency = 73 GHz
10
Frequency = 75 GHz
10
1
1
0.1
0.1
0.01
0.01
0.001
0.001
-12 -9 -6 -3
0
3
6
9
12 15 18 21 24
-12 -9 -6 -3
0
3
6
9
12 15 18 21 24
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
+25 C
+85 C
-55 C
+25 C
+85 C
-55 C
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
2
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Detector Voltage vs. Temperature,
Detector Voltage vs. Temperature,
Frequency = 81 GHz
10
Frequency = 83 GHz
10
1
1
0.1
0.1
0.01
0.01
0.001
0.001
-14 -11 -8
-5
-2
1
4
7
10 13 16 19
-14 -11 -8
-5
-2
1
4
7
10 13 16 19
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
+25 C
+85 C
-55 C
+25 C
+85 C
-55 C
Detector Voltage vs. Temperature,
Detector Voltage vs. Frequency,
Frequency = 85 GHz
10
Frequency = 71 - 75 GHz
10
1
1
0.1
0.1
0.01
0.001
0.01
0.001
-14 -11 -8
-5
-2
1
4
7
10 13 16 19
-12 -9 -6 -3
0
3
6
9
12 15 18 21 24
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
+25 C
+85 C
-55 C
71 GHz
73 GHz
75 GHz
Detector Voltage vs. Frequency,
Reference Node Voltage vs. Pout,
Frequency = 81 - 85 GHz
10
Frequency = 75 GHz
10
1
1
0.1
0.1
0.01
0.001
0.01
-14 -11 -8
-5
-2
1
4
7
10 13 16 19
-12 -9 -6 -3
0
3
6
9
12 15 18 21 24
OUTPUT POWER (dBm)
OUTPUT POWER (dBm)
Vref (V)
81 GHz
83 GHz
85 GHz
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
3
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Table 1. Absolute Maximum Ratings
RF Input
+25 dBm
Operating Temperature
Storage Temperature
ESD Sensitivity (HBM)
-55 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
-65 to 150 °C
Class 1A, passed 250V
Outline Drawing
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM].
2. DIE THICKNESS IS 0.004”
Table 2. Die Packaging Information [1]
3. BOND PADS 1, 2, 3 & 4 ARE 0.0038” [0.096] X 0.0038” [0.096].
4. BACKSIDE METALLIZATION: GOLD.
Standard
Alternate
5. BOND PAD METALLIZATION: GOLD.
GP-1 (Gel Pack)
[2]
6. BACKSIDE METAL IS GROUND.
[1] For more information refer to the “Packaging
information” Document in the Product Support Section of
our website.
7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
8. OVERALL DIE SIZE 0.002
[2] For alternate packaging information contact Hittite
Microwave Corporation.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
4
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Pin Descriptions
Pad Number
Function
Description
Pad Schematic
1
RF IN
These ports are matched to 50 Ohms.
2
3
RF OUT
DC voltage representing RF output power rectified by
diode which is biased through an external resistor. See
application circuit.
Vdet
Vref
DC voltage of diode biased through external resistor used
for temperature compensation of Vdet. See application
circuit.
4
Die Bottom
GND
Die bottom must be connected to RF/DC ground.
Assembly Diagram
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
5
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Application Circuit
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
6
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
0.102mm (0.004”) Thick GaAs MMIC
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accom-
plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be located as close to the die as possible
in order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
Handling Precautions
Follow these precautions to avoid permanent damage.
0.102mm (0.004”) Thick GaAs MMIC
Storage: All bare die are placed in either Waffle or Gel based ESD pro-
tective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Wire Bond
0.076mm
(0.003”)
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
RF Ground Plane
Static Sensitivity: Follow ESD precautions to protect against > 250V
ESD strikes.
0.150mm (0.005”) Thick
Moly Tab
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-up.
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
General Handling: Handle the chip along the edges with a vacuum collet
or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched
with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO
NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is rec-
ommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started
on the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils).
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
7
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC7447
v00.0913
E-BAND DETECTOR
71 - 86 GHz
Notes:
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
8
相关型号：
HMC744LC3
14 Gbps Fast Rise Time 1:2 Fanout Buffer with Programmable Output Voltage & Positive Supply
ADI
HMC744LC3C
13 Gbps, FAST RISE TIME 1:2 FANOUT BUFFER w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY
HITTITE
HMC744LC3C_10
13 Gbps, FAST RISE TIME 1:2 FANOUT BUFFER w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY
HITTITE
HMC744LC3TR
14 Gbps Fast Rise Time 1:2 Fanout Buffer with Programmable Output Voltage & Positive Supply
ADI
HMC745LC3
13 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY
HITTITE
HMC745LC3
13 Gbps, Fast Rise Time XOR/XNOR Gate with Programmable Output Voltage and Positive Supply
ADI
HMC745LC3C
13 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY
HITTITE
HMC745LC3C_11
13 Gbps, FAST RISE TIME XOR / XNOR GATE w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY
HITTITE
©2020 ICPDF网 联系我们和版权申明