SDX100G2-A [HONEYWELL]
Peizoresistive Sensor, Gage, 0Psi Min, 100Psi Max, 0-100mV, Rectangular, Through Hole Mount, 0.600 INCH, DOUBLE WIDTH, DIP-6;型号: | SDX100G2-A |
厂家: | Honeywell |
描述: | Peizoresistive Sensor, Gage, 0Psi Min, 100Psi Max, 0-100mV, Rectangular, Through Hole Mount, 0.600 INCH, DOUBLE WIDTH, DIP-6 传感器 换能器 |
文件: | 总4页 (文件大小:42K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Low Cost Compensated Pressure Sensors
in a DIP Package
SDX Series
FEATURES
• Low Cost DIP
• Temperature Compensated
• Calibrated Zero & Span
• Small Size
• Low Noise
• High Impedance for Low Power
Applications
• Prime Grade Available
TYPICAL APPLICATIONS
• Medical Equipment
The SDX series sensors provide a very cost effective solution for pressure
applications that require small size plus performance. These calibrated
and temperature compensated sensors give an accurate and stable output
over a 0°C to 50°C temperature range. This series is intended for use with
non-corrosive, non-ionic working fluids such as air, dry gases and the like.
• Computer Peripherals
• Pneumatic Controls
• HVAC
EQUIVALENT CIRCUIT
V
s
Devices are available to measure absolute and gauge pressures from
1 psi up to 100 psi. The absolute devices have an internal vacuum
reference and an output voltage proportional to absolute pressure.
The output of the bridge is ratiometric to the supply voltage and operation
from any DC supply voltage up to +20 V is acceptable.
The SDX devices feature an integrated circuit sensor element and laser
trimmed thick film ceramic housed in a compact solvent resistant case.
The package is a double wide (i.e., 0.600” lead spacing) dual-inline-
package. This is the same familiar package used by IC manufacturers
except it is only 0.470” long and has a pressure port(s). The pc board area
used by each DIP is approximately 0.26 square inches. This extremely
small size enables the use of multiple sensors in limited available space.
The DIP provides excellent corrosion resistance and isolation to external
package stress.
- Out
+Out
The DIP mounts on a pc board like a standard IC with through-hole pins.
The pins anchor the pressure sensor to the pc board and provide a more
secure and stable unit than other types of packages.
Contact your local SenSym ICT representative, the factory, or go to
Sensym ICT’s Web site at www.sensym-ict.com for additional details.
!
!
WARNING
MISUSE OF DOCUMENTATION
WARNING
PERSONAL INJURY
• The information presented in this product sheet is for reference
DO NOT USE these products as
safety or emergency stop devices
or in any other application where
failure of the product could result
in personal injury.
Failure to comply with these
instructions could result in
death or serious injury.
only. Do not use this document as a product installation guide.
• Complete installation, operation, and maintenance information
is provided in the instructions supplied with each product.
Failure to comply with these instructions could result in death
or serious injury.
Automation and Control Products
© Honeywell 2002, All Rights Reserved
Low Cost Compensated Pressure Sensors
in a DIP Package
SDX Series
PRESSURE SENSOR CHARACTERISTICS (All Devices)
Maximum Ratings
Supply Voltage VS
Maximum Pressure on any Port
Lead Temperature (Soldering 2-4 Sec.)
Environmental Specifications
Temperature Range
Compensated
+20 Vdc
150 psig
250°C
0°C to
-40°C to
-55°C to
50°C
85°C
125°C
Operating
Storage
Humidity Limits
0 to 100% RH
PRESSURE RANGE SPECIFICATIONS
Part Number
Operating
Pressure
Proof
Full-Scale Span(2)
Typ
Pressure
Min
Max
SDX01
0 - 1 psi
0 - 1 psi
20 psi
20 psi
20 psi
20 psi
30 psi
30 psi
60 psi
60 psi
150 psi
150 psi
17.37 mV
17.82 mV
57.9 mV
59.4 mV
86.85 mV
89.1 mV
86.85 mV
89.1 mV
96.5 mV
99.0 mV
18.0 mV
18.0 mV
60.0 mV
60.0 mV
90.0 mV
90.0 mV
90.0 mV
90.0 mV
100.0 mV
100.0 mV
18.63 mV
18.18 mV
62.1 mV
60.6 mV
93.15 mV
90.9 mV
93.15 mV
90.9 mV
103.5 mV
101.0 mV
SDX01yy-A
SDX05
0 - 5 psi
SDX05yy-A
SDX15
0 - 5 psi
0 - 15 psi
0 - 15 psi
0 - 30 psi
0 - 30 psi
0 - 100 psi
0 - 100 psi
SDX15yy-A
SDX30
SDX30yy-A
SDX100
SDX100yy-A
SDX PERFORMANCE CHARACTERISTICS(1)
Characteristics
Min
-1.0
–
Typ
0
Max
1.0
±1.0
±2.0
±1.0
±0.5
–
Unit
mV
Zero Pressure Offset
Combined Pressure Non-Linearity and Pressure Hysteresis(3)
Temperature Effect on Span(0° - 50°C)(4)
Temperature Effect on Offset (0° - 50°C)(4)
Repeatability(5)
±0.2
±0.4
±0.2
±0.2
4.0
%FSO
%FSO
mV
–
–
–
%FSO
kΩ
Input Resistance6)
–
Output Resistance(7)
–
4.0
–
kΩ
Common-Mode Voltage(8)
Response Time(9)
Long-Term Stability of Offset and Span(10)
1.5
–
3.0
5.0
–
Vdc
100
±0.1
µsec
%FSO
–
–
2 Honeywell • Automation and Control Products
Low Cost Compensated Pressure Sensors
in a DIP Package
SDX Series
SDX PRIME GRADE PERFORMANCE CHARACTERISTICS(1)
Characteristics
Zero Pressure Offset(12)
Combined Pressure Non-Linearity and Pressure Hysteresis(3,11)
Temperature Effect on Span(0° - 50°C)(4)
Temperature Effect on Offset (0° - 50°C)(4)
Repeatability(5)
Min
Typ
0
Max
Unit
mV
-0.300
0.300
±0.25
±1.0
±0.5
–
–
–
±0.1
±0.4
±0.2
±0.1
4.0
%FSO
%FSO
mV
–
–
%FSO
kΩ
Input Resistance6)
–
–
Output Resistance(7)
–
4.0
–
kΩ
Common Mode Voltage(8)
Response Time(9)
Long Term Stability of Offset and Span(10)
1.5
–
3.0
5.0
–
Vdc
100
±0.1
µsec
mV
–
–
SPECIFICATION NOTES
Note 1: Reference Conditions (unless otherwise noted):
TA = 25°C, Supply VS = 12 Vdc, Common Mode Line Pressure = 0 psig. Pressure applied to port 2. For absolute
devices only, pressure is applied to port 1 and the output polarity is reversed.
Note 2: Full-Scale Span is the algebraic difference between the output voltage at full-scale pressure and the output
at zero pressure. Full-Scale Span (FSS) is ratiometric to the supply voltage.
Note 3: Pressure Hysteresis is the maximum output difference at any point within the operating pressure range for
increasing and decreasing pressure.
Note 4: Maximum error band of the offset voltage and the error band of the span, relative to the 25°C reading.
Note 5: Maximum difference in output at any pressure with the operating pressure range and temperature within 0°C
to 50°C after:
a) 100 temperature cycles, 0°C to 50°C.
b) 1.0 million pressure cycles, 0 psi to Full-Scale Span.
Note 6: Input resistance is the resistance between VS and ground.
Note 7: Output resistance is the resistance between the + and - outputs.
Note 8: This is the common mode voltage of the output arms for VS = 12 Vdc.
Note 9: Response time for a 0 psi to Full-Scale Span pressure step change, 10% to 90% rise time.
Note 10: Long term stability over a one year period.
Note 11: Maximum combing Pressure Non-Linearity and Pressure Hysteresis for the SDX05 Prime Grade is ±0.5%.
Note 12: Maximum zero pressure offset for absolute devices is ±500 µV.
ELECTRICAL CONNECTIONS
OUTPUT +
GROUND
OUTPUT -
OUTPUT -
GROUND
OUTPUT +
OUTPUT +
GROUND
OUTPUT -
1
1
1
+V
+V
s
+V
s
s
4
4
4
GAUGE
ABSOLUTE
DIFFERENTIAL/GAUGE
SDXxxxG2
SDXxxxD4
SDXxxxA2
Honeywell • Automation and Control Products 3
Low Cost Compensated Pressure Sensors
in a DIP Package
SDX Series
PHYSICAL DIMENSIONS
WARRANTY/REMEDY
Honeywell warrants goods of its
manufacture as being free of
defective materials and faulty
workmanship. Contact your local
sales office for warranty
Ø.105
2° DRAFT
.315
.550
.545
.28
information. If warranted goods
are returned to Honeywell during
the period of coverage,
.470
.19 TYP
COMPENSATION
CERAMIC
.110 TYP
.020 TYP
Honeywell will repair or replace
without charge those items it
finds defective. The foregoing is
Buyer’s sole remedy and is in
lieu of all other warranties,
expressed or implied,
.60
.010 TYP
.100 TYP
.300
.550
.14
Ø.090
2° DRAFT
.37
.28
.470
including those of
merchantability and fitness for
a particular purpose.
COMPENSATION
CERAMIC
.19 TYP
.110 TYP
.020 TYP
.100 TYP
Specifications may change
without notice. The information
we supply is believed to be
accurate and reliable as of this
printing. However, we assume no
responsibility for its use.
While we provide application
assistance personally, through
our literature and the Honeywell
web site, it is up to the customer
to determine the suitability of the
product in the application.
For application assistance,
current specifications, or name of
the nearest Authorized
.60
.010 TYP
.31 [7.9]
TYP
.55 [14.0]
.135 ±0.012 [3.4 ±0.3]
Ø.09 [2.3] TYP.
.250 ±0.012 [6.4 ±0.3]
.47 [11.9]
2° DRAFT
.29 [7.2]
.34 [8.6]
COMPENSATION
CERAMIC
ALL PRIMARY DIMENSIONS
ARE INCHES
.60 [15.2]
.01 [.3] TYP.
.02 [.5] TYP
.10 [2.5] TYP
ORDERING INFORMATION
SDX XXX
D4
Distributor, contact a nearby
sales office.
Or call:
SenSym ICT
Pressure Transducer
Pressure Connection and Pressure Type:
D4 "D4" DIP Package, Temperature
Compensated Differential Sensor
1-800-537-6945 USA
G2 "D2" DIP Package, Temperature
Compensated Gauge Sensor
Pressure Range (psi)
01 = 0-1 psi
1-800-737-3360 Canada
1-815-235-6847 International
FAX
1-815-235-6545 USA
INTERNET
A2 "D2" DIP Package, Temperature
Compensated Absolute Sensor
05 = 0-5 psi
A4 "D4" DIP Package, Temperature
Compensated Absolute Sensor
15 = 0-15 psi
30 = 0-30 psi
100 = 0-100 psi
D4-A "D4" DIP Package, Prime Grade
Temperature Compensated Differential Sensor
G2-A "D2" DIP Package, Prime Grade
Temperature Compensated Gauge Sensor
www.honeywell.com/sensing
info.sc@honeywell.com
A2-A "D2" DIP Package, Prime Grade
Temperature Compensated Absolute Sensor
A4-A "D4" DIP Package, Prime Grade
Temperature Compensated Absolute Sensor
Sensing and Control
Honeywell
11 West Spring Street
Freeport, Illinois 61032
PK XXXXX-X-XX IL50 GLO MYR Printed in USA
www.honeywell.com/sensing
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明