HB3623SSIP5D [HOPERF]

SAW FILTER; SAW滤波器


型号：	HB3623SSIP5D
厂家：	HOPERF
描述：	SAW FILTER SAW滤波器 LTE
文件：	总5页 (文件大小：103K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Approved by:

Checked by:

Issued by:

SPECIFICATION

PRODUCT: SAW FILTER

MODEL:

HB3623S (X7255N) SIP5D

HOPE MICROELECTRONICS CO.,LIMITED

Tel:+86-755-82973806 Fax:+86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com

Page 1 of

1.Construction

1.1 Dimension and materials

Type : B3623S

1.2. Circuit construction, measurement circuit

2.Characteristics

Standard atmospheric conditions

Unless otherwise specified , the standard rang of atmospheric conditions for making

measurements and tests is as follows;

Ambient temperature : 15℃ to 35℃

Relative humidity

Air pressure

: 25% to 85%

: 86kPa to 106kPa

Operating temperature rang

Operating temperature rang is the rang of ambient temperatures in which the filter

can be

operated continuously. -10℃ ~ +60℃

Storage temperature rang

Storage temperature rang is the rang of ambient temperatures at which the filter can

be stored without damage.

Conditions are as specified elsewhere in these specifications. -40℃ ~ +70℃

Reference temperature

2.1 Maximum Rating

+25℃

DC voltage

AC voltage

VDC

Vpp

Between any terminals

2.2 Characteristics of channel 1 (switching input pin 2 connected to ground)

Source impedance

Load impedance

Item

Center frequency

Insertion attenuation

Reference level

Zs=50Ω

Z_L=2kΩ//3pF

Freq

T_A=25℃

min

typ

36.00

max

MHz

36.00MHz

18.4

20.4

22.4

B1.5dB

B3dB

B15dB

7.1

7.4

8.4

MHz

Pass bandwidth

B30dB

8.8

30.75MHz

40.25MHz

40.75MHz

41.00MHz

41.25MHz

34.0

12.0

34.0

30.0

34.0

31.0

32.0

41.0

18.0

48.0

44.0

50.0

36.0

37.0

Relative attenuation

25.00~31.30MHz

40.70~45.00MHz

Sidelobe

Reflected wave signal suppression

1.2 us … 6.0 us after main pulse

(test pulse 250 ns ,

40.0

48.0

carrier frequency 36.00MHz)

Group delay ripple (p-p)

32.40~39.60 MHz

Temperature coefficient

-72

ppm/k

Characteristics of channel 2 (switching input pin 2 connected to pin 1)

Source impedance

Load impedance

Item

Center frequency

Insertion attenuation

Reference level

Zs=50Ω

Z_L=2kΩ//3pF

Freq

T_A=25℃

min

typ

36.00

max

MHz

36.00MHz

18.9

20.9

22.9

B1.5dB

B3dB

B15dB

6.2

6.4

7.4

MHz

Pass bandwidth

B30dB

7.8

31.42MHz

39.67MHz

39.92MHz

33.0

10.0

22.0

32.0

31.0

41.0

15.0

30.0

40.0

37.0

Relative attenuation

25.00~31.80MHz

40.20~45.00MHz

Sidelobe

Reflected wave signal suppression

1.2 us … 6.0 us after main pulse

(test pulse 250 ns ,

40.0

48.0

carrier frequency 36.00MHz)

Group delay ripple (p-p)

32.90~39.10 MHz

Temperature coefficient

-72

ppm/k

2.3 Environmental Performance Characteristics

Item Test condition

Allowable change of absolute

Level at center frequency(dB)

High temperature test

70℃ 1000H

< 1.0

Low temperature test

-40℃ 1000H

Humidity test

< 1.0

40℃ 90-95% 1000H

Thermal shock

-20℃==25℃==80℃ 20 cycle

< 1.0

30M

10M

30M

Solder temperature test

Sold temp.260℃ for 10 sec.

Soldering

Immerse the pins melt solder

at 260℃+5/-0℃ for 5 sec.

More then 95% of total

area of the pins should

be covered with solder

2.4 Mechanical Test

Item

Test condition

Allowable change of absolute

Level at center frequency(dB)

Vibration test

600-3300rpm amplitude 1.5mm

3 directions 2 H each

Drop test

On maple plate from 1 m high 3 times

Lead pull test

<1.0

Pull with 1 kg force for 30 seconds

Lead bend test

90^obending with 500g weigh 2 times

2.5 Voltage Discharge Test

Item

Test condition

Allowable change of absolute

Level at center frequency(dB)

Surge test

Between any two electrode

<1.0

相关型号：