RFM63B [HOPERF]
ISM TRANSCEIVER MODULE;
| 型号： | RFM63B |
| 厂家： | 
HOPERF |
| 描述： | ISM TRANSCEIVER MODULE ISM频段 |
| 文件： | 总90页 (文件大小：3521K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RFM63B
RFM63B ISM TRANSCEIVER MODULE V1.1
ADVANCED COMMUNICATIONS & SENSING
General Description
The RFM63B is a low cost transceiver module
operating in the 868 and 915MHz frequency bands,
The RFM63B is optimized for very low power
consumption (3mA in receiver mode). It incorporates a
baseband modem with data rates up to 200 kb/s. Data
handling features include a sixty-four byte FIFO,
packet handling, automatic CRC generation and data
whitening.
All major RF communication parameters are
programmable and most of them may be dynamically
set. It complies with European (ETSI EN 300-220
V2.1.1) and North American (FCC part 15.247 and
15.249) regulatory standards.
RFM63B
（Note：RFM63B for No SAW filter module，
Application transmit function can't meet the FCC/CE
standard requirements）
In order to better use RFM63B modules, this
specification also involves a large number of the
parameters and functions of its core chip RF63's,
including those IC pins which are not leaded out. All
of these can help customers gain a better
understanding of the performance of RFM63B
modules, and enhance the application skills.
Applications
•
•
•
•
•
•
Wireless alarm and security systems
Wireless sensor networks
Automated Meter Reading
Home and building automation
Industrial monitoring and control
Remote Wireless Control
Features
•
•
•
Low Rx power consumption: 3mA
Low Tx power consumption: 25 mA @ +10 dBm
Good reception sensitivity: down to -105 dBm at
25 kb/s in FSK, -111 dBm at 2kb/s in OOK
Programmable RF output power: up to +12 dBm in
8 steps
Packet handling feature with data whitening and
automatic CRC generation
Wide RSSI (Received Signal Strength Indicator)
dynamic range, 70dB from Rx noise floor
Bit rates up to 200 kb/s, NRZ coding
On-chip frequency synthesizer
•
•
•
•
•
•
•
•
FSK and OOK modulation
Incoming sync word recognition
Built-in Bit-Synchronizer for incoming data and
clock synchronization and recovery
Module Size： 19.7X16mm
Optimized Circuit Configuration for Low-cost
applications
•
•
Page 1 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Table of Contents
1. General Description.................................................................. 5
1.1. Simplified Block Diagram....................................................... 5
1.2. Pin Diagram........................................................................... 6
1.3. Pin Description ...................................................................... 7
2. Electrical Characteristics .......................................................... 8
2.1. ESD Notice............................................................................ 8
2.2. Absolute Maximum Ratings ................................................... 8
2.3. Operating Range ................................................................... 8
2.4. Chip Specification.................................................................. 8
2.4.1. Power Consumption ........................................................... 8
2.4.2. Frequency Synthesis .......................................................... 9
2.4.3. Transmitter ......................................................................... 9
2.4.4. Receiver........................................................................... 10
2.4.5. Digital Specification .......................................................... 11
3. Architecture Description.......................................................... 12
3.1. Power Supply Strategy ........................................................ 12
3.2. Frequency Synthesis Description......................................... 13
3.2.1. Reference Oscillator ......................................................... 13
3.2.2. CLKOUT Output ............................................................... 13
3.2.3. PLL Architecture............................................................... 14
3.2.4. PLL Tradeoffs................................................................... 14
3.2.5. Voltage Controlled Oscillator............................................. 15
3.2.6. PLL Loop Filter ................................................................. 16
3.2.7. PLL Lock Detection Indicator ............................................ 16
3.2.8. Frequency Calculation...................................................... 16
3.3. Transmitter Description........................................................ 18
3.3.1. Architecture Description.................................................... 18
3.3.2. Bit Rate Setting................................................................. 19
3.3.3. Alternative Settings........................................................... 19
3.3.4. Fdev Setting in FSK Mode................................................ 19
3.3.5. Fdev Setting in OOK Mode............................................... 19
3.3.6. Interpolation Filter............................................................. 20
3.3.7. Power Amplifier ................................................................ 20
3.3.8. Common Input and Output Front-End............................... 22
3.4. Receiver Description............................................................ 23
3.4.1. Architecture ...................................................................... 23
3.4.2. LNA and First Mixer.......................................................... 24
3.4.3. IF Gain and Second I/Q Mixer........................................... 24
3.4.4. Channel Filters ................................................................. 24
3.4.5. Channel Filters Setting in FSK Mode ................................ 25
3.4.6. Channel Filters Setting in OOK Mode ............................... 26
3.4.7. RSSI................................................................................. 26
3.4.8. Fdev Setting in Receive Mode .......................................... 28
3.4.9. FSK Demodulator............................................................. 28
3.4.10. OOK Demodulator.......................................................... 28
3.4.11. Bit Synchronizer ............................................................. 31
3.4.12. Alternative Settings......................................................... 32
3.4.13. Data Output .................................................................... 32
4. Operating Modes.................................................................... 33
4.1. Modes of Operation............................................................. 33
4.2. Digital Pin Configuration vs. Chip Mode............................... 33
5. Data Processing..................................................................... 34
5.1. Overview ............................................................................. 34
5.1.1. Block Diagram .................................................................. 34
5.1.2. Data Operation Modes...................................................... 34
5.2. Control Block Description..................................................... 35
5.2.1. SPI Interface..................................................................... 35
5.2.2. FIFO................................................................................. 38
5.2.3. Sync Word Recognition .................................................... 40
5.2.4. Packet Handler................................................................. 40
5.2.5. Control.............................................................................. 40
5.3. Continuous Mode ................................................................ 41
5.3.1. General Description .......................................................... 41
5.3.2. Tx Processing................................................................... 41
5.3.3. Rx Processing................................................................... 42
5.3.4. Interrupt Signals Mapping ................................................. 42
5.3.5. uC Connections ................................................................ 43
5.3.6. Continuous Mode Example............................................... 43
5.4. Buffered Mode..................................................................... 44
5.4.1. General Description .......................................................... 44
5.4.2. Tx Processing................................................................... 44
5.4.3. Rx Processing................................................................... 45
5.4.4. Interrupt Signals Mapping ................................................. 46
5.4.5. uC Connections ................................................................ 47
5.4.6. Buffered Mode Example.................................................... 47
5.5. Packet Mode........................................................................ 49
5.5.1. General Description .......................................................... 49
5.5.2. Packet Format .................................................................. 49
5.5.3. Tx Processing................................................................... 51
5.5.4. Rx Processing................................................................... 51
5.5.5. Packet Filtering................................................................. 52
5.5.6. DC-Free Data Mechanisms............................................... 53
5.5.7. Interrupt Signal Mapping................................................... 54
5.5.8. uC Connections ................................................................ 55
5.5.9. Packet Mode Example...................................................... 56
5.5.10. Additional Information ..................................................... 56
6. Configuration and Status Registers......................................... 58
6.1. General Description............................................................. 58
6.2. Main Configuration Register - MCParam..............................58
6.3. Interrupt Configuration Parameters - IRQParam ..................60
6.4. Receiver Configuration parameters - RXParam ...................62
6.5. Sync Word Parameters - SYNCParam.................................63
6.6. Transmitter Parameters - TXParam ..................................... 64
6.7. Oscillator Parameters - OSCParam ..................................... 64
6.8. Packet Handling Parameters
—
PKTParam ...........................65
7. Application Information ........................................................... 66
7.1. Crystal Resonator Specification ........................................... 66
7.2. Software for Frequency Calculation ..................................... 66
7.2.1. GUI....................................................................................66
7.2.2. .dll for Automatic Production Bench .................................. 66
7.3. Switching Times and Procedures......................................... 66
7.3.1. Optimized Receive Cycle.................................................. 67
7.3.2. Optimized Transmit Cycle................................................. 68
7.3.3. Transmitter Frequency Hop Optimized Cycle.................... 69
7.3.4. Receiver Frequency Hop Optimized Cycle........................ 70
7.3.5. Rx Tx and Tx Rx Jump Cycles ....................................... 71
7.4. Reset of the Chip................................................................. 72
7.4.1. POR................................................................................... 72
7.4.2. Manual Reset..................................................................... 72
7.5. Reference Design................................................................. 73
7.5.1. Application Schematic....................................................... 73
7.5.2. PCB Layout ....................................................................... 73
7.5.3. Bill Of Material ................................................................... 74
7.5.4. SAW Filter Plot .................................................................. 75
7.5.5. Ordering Information for Tools .......................................... 75
7.6. Reference Design Performance...........................................76
7.6.1. Sensitivity Flatness ........................................................... 77
7.6.2. Sensitivity vs. LO Drift....................................................... 78
7.6.3. Sensitivity vs. Receiver BW .............................................. 79
7.6.4. Sensitivity Stability over Temperature and Voltage............80
7.6.5. Sensitivity vs. Bit Rate ....................................................... 80
7.6.6. Adjacent Channel Rejection.............................................. 81
7.6.7. Output Power Flatness...................................................... 82
7.6.8. Pout and IDD vs. PA Setting............................................. 83
Page 2 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
8. Packaging Information............................................................ 90
9. Ordering Information…………………………….………………...91
7.6.9. Pout Stability over Temperature and Voltage.................... 84
7.6.10. Transmitter Spectral Purity ............................................. 85
7.6.11. OOK Channel Bandwidth................................................ 86
7.6.12. FSK Spectrum in Europe ................................................ 87
7.6.13. Digital Modulation Schemes............................................ 88
7.6.14. Current Stability over Temperature and Voltage ............. 89
Index of Figures
Figure 1: RFM63B Simplified Block
Diagram ..................................... 5
Figure 2: RFM63B Pin
Diagram ......................................................... 6
Figure 3: RFM63B Detailed Block Diagram......................................
12
Figure 46: Manchester Encoding/Decoding ................................ 54
Figure 47: Data Whitening .......................................................... 54
Figure 48: uC Connections in Packet Mode................................55
Figure 49: Optimized Rx Cycle ................................................... 67
Figure 50: Optimized Tx Cycle.................................................... 68
Figure 51: Tx Hop Cycle............................................................. 69
Figure 52: Rx Hop Cycle............................................................. 70
Figure 4: Power Supply Breakdown............................................ 13
Figure 5: Frequency Synthesizer Description.............................. 14
Figure 6: LO Generator .............................................................. 14
Figure 7: Loop Filter ................................................................... 16
Figure 8: Transmitter Architecture .............................................. 18
Figure 9: I(t), Q(t) Overview........................................................ 18
Figure 10: PA Control................................................................. 21
Figure 11: Optimal Load Impedance Chart ................................. 21
Figure 12: Recommended PA Biasing and Output Matching ..... 22
Figure 13: Front-end Description ................................................ 22
Figure 14: Receiver Architecture ................................................ 23
Figure 15: FSK Receiver Setting ................................................ 23
Figure 16: OOK Receiver Setting ............................................... 23
Figure 17: Active Channel Filter Description............................... 24
Figure 18: Butterworth Filter's Actual BW ................................... 26
Figure 19: Polyphase Filter's Actual BW ..................................... 26
Figure 20: RSSI Dynamic Range................................................ 27
Figure 21: RSSI IRQ Timings ..................................................... 28
Figure 22: OOK Demodulator Description................................... 29
Figure 23: Floor Threshold Optimization..................................... 30
Figure 24: BitSync Description..................................................... 31
Figure 25: RFM63B‟s Data Processing Conceptual
Figure 53: Rx Tx
Rx Cycle ................................................. 71
Figure 54: POR Timing Diagram................................................. 72
Figure 55: Manual Reset Timing Diagram................................... 72
Figure 56: Reference Design Circuit Schematic.......................... 73
Figure 57: Reference Design„s Stackup...................................... 74
Figure 58: Reference Design Layout (top view) ..........................74
Figure 59: 915 MHz SAW Filter Plot ...........................................75
Figure 60: 869 MHz SAW Filter Plot ...........................................75
Figure 61: Sensitivity Across the 868 MHz Band......................... 77
Figure 62: Sensitivity Across the 915 MHz Band......................... 77
Figure 63: FSK Sensitivity Loss vs. LO Drift................................78
Figure 64: OOK Sensitivity Loss vs. LO Drift............................... 78
Figure 65: FSK Sensitivity vs. Rx BW .........................................79
Figure 66: OOK Sensitivity Change vs. Rx BW...........................79
Figure 67: Sensitivity Stability..................................................... 80
Figure 68: FSK Sensitivity vs. BR ............................................... 80
Figure 69: OOK Sensitivity vs. BR .............................................. 81
Figure 70: ACR in FSK Mode...................................................... 81
Figure 71: ACR in OOK Mode..................................................... 82
Figure 72: Pout for 869 MHz Band Operation .............................82
Figure 73: Pout for 915 MHz Band Operation .............................83
Figure 74: Pout and IDD at all PA Settings, 869 MHz .................83
Figure 75: Pout and IDD at all PA Settings, 915 MHz .................84
Figure 76: Pout Stability.............................................................. 84
Figure 77: 869 MHz Spectral Purity DC-1GHz ............................85
Figure 78: 869 MHz Spectral Purity 1-6GHz ...............................85
Figure 79: OOK Spectrum - 2kbps.............................................. 86
Figure 80: OOK Spectrum - 8kbps.............................................. 86
Figure 81: OOK Spectrum - 16.7kbps.........................................86
Figure 82: FSK - 1.56kbps - +/-33 kHz.........................................87
Figure 83: FSK - 25 kbps - +/-50 kHz........................................... 87
Figure 84: FSK - 40 kbps - +/-40 kHz........................................... 87
Figure 85: DTS 6dB Bandwidth................................................... 88
Figure 86: DTS Power Spectral Density...................................... 88
Figure 87: IDD vs. Temp and VDD.............................................. 89
Figure 88: Package Dimensions.................................................. 90
View...............34
Figure 26: SPI Interface Overview and uC Connections ............. 35
Figure 27: Write Register Sequence........................................... .36
Figure 28: Read Register Sequence........................................... 37
Figure 29: Write Bytes Sequence (ex: 2 bytes)........................... 37
Figure 30: Read Bytes Sequence (ex: 2 bytes)........................... 38
Figure 31: FIFO and Shift Register (SR)..................................... 38
Figure 32: FIFO Threshold IRQ Source Behavior ....................... 39
Figure 33: Sync Word Recognition ............................................. 40
Figure 34: Continuous Mode Conceptual View........................... 41
Figure 35: Tx Processing in Continuous Mode............................ 41
Figure 36: Rx Processing in Continuous Mode ........................... 42
Figure 37: uC Connections in Continuous Mode......................... 43
Figure 38: Buffered Mode Conceptual View................................ 44
Figure 39: Tx processing in Buffered Mode ................................ 45
Figure 40: Rx Processing in Buffered Mode................................ 46
Figure 41: uC Connections in Buffered Mode ............................. 47
Figure 42: Packet Mode Conceptual View.................................. 49
Figure 43: Fixed Length Packet Format...................................... 50
Figure 44: Variable Length Packet Format.................................. 51
Figure 45: CRC Implementation ................................................. 53
Page 3 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Index of Tables
Table 1: Ordering Information....................................................... 1
Table 2: RFM63B Pinouts...............................................................
7
Table 20: Interrupt Mapping in Buffered Rx and Stby Modes ...... 46
Table 21: Interrupt Mapping in Buffered Tx Mode .......................46
Table 22: Relevant Configuration Registers in Buffered Mode ....47
Table 23: Interrupt Mapping in Rx and Stby in Packet Mode.......55
Table 24: Interrupt Mapping in Tx Packet Mode..........................55
Table 25: Relevant Configuration Registers in Packet Mode.......56
Table 26: Registers List.............................................................. 58
Table 27: MCParam Register Description...................................58
Table 28: IRQParam Register Description ..................................60
Table 29: RXParam Register Description.................................... 62
Table 30: SYNCParam Register Description...............................63
Table 31: TXParam Register Description....................................64
Table 32: OSCParam Register Description.................................64
Table 33: PKTParam Register Description..................................65
Table 34: Crystal Resonator Specification .................................. 66
Table 35: Reference Design BOM .............................................. 74
Table 36: Tools Ordering Information.......................................... 75
Table 37: FSK Rx Filters vs. Bit Rate.......................................... 76
Table 38: OOK Rx Filters vs. Bit Rate.........................................76
Table 3: Absolute Maximum Ratings ............................................ 8
Table 4: Operating Range ............................................................ 8
Table 5: Power Consumption Specification................................... 8
Table 6: Frequency Synthesizer Specification .............................. 9
Table 7: Transmitter Specification ................................................ 9
Table 8: Receiver Specification ................................................... 10
Table 9: Digital Specification ....................................................... 11
Table 10: MCParam_Freq_band Setting..................................... 15
Table 11: PA Rise/Fall Times ...................................................... 20
Table 12: Operating Modes ......................................................... 33
Table 13: Pin Configuration vs. Chip Mode.................................. 33
Table 14: Data Operation Mode Selection................................... 35
Table 15: Config vs. Data SPI Interface Selection ....................... 36
Table 16: Status of FIFO when Switching Between Different
Modes of the Chip ....................................................................... 39
Table 17: Interrupt Mapping in Continuous Rx Mode ................... 42
Table 18: Interrupt Mapping in Continuous Tx Mode.................... 42
Table 19: Relevant Config. Registers in Continuous Mode ......... 43
Acronyms
LO
Local Oscillator
BOM
BR
Bill Of Materials
Bit Rate
LSB
MSB
NRZ
NZIF
OOK
PA
Least Significant Bit
Most Significant Bit
Non Return to Zero
Near Zero Intermediate Frequency
On Off Keying
BW
Bandwidth
Comité Consultatif International
CCITT
Téléphonique et Tél égraphique - ITU
Charge Pump
CP
Power Amplifier
CRC
DAC
DDS
DLL
ERP
Cyclic Redundancy Check
Digital to Analog Converter
Direct Digital Synthesis
PCB
PFD
PLL
POR
RBW
RF
Printed Circuit Board
Phase Frequency Detector
Phase-Locked Loop
Power On Reset
Dynamically Linked Library
Equivalent Radiated Power
European Telecommunications Standards
Resolution BandWidth
Radio Frequency
ETSI
I
nstitute
RSSI
Rx
Received Signal Strength Indicator
Receiver
FCC
Fdev
FIFO
FS
Federal Communications Commission
Frequency Deviation
SAW
SPI
Surface Acoustic Wave
Serial Peripheral Interface
Shift Register
First In First Out
Frequency Synthesizer
Frequency Shift Keying
Graphical User Interface
Integrated Circuit
SR
FSK
GUI
IC
Stby
Tx
Standby
Transmitter
uC
Microcontroller
ID
IDentificator
VCO
XO
Voltage Controlled Oscillator
Crystal Oscillator
IF
Intermediate Frequency
Interrupt ReQuest
IRQ
ITU
LFSR
LNA
XOR
eXclusive OR
International Telecommunication Union
Linear Feedback Shift Register
Low Noise Amplifier
Page 4 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
This product datasheet contains a detailed description of the RFM63B performance and functionality. Please consult
the HopeRF website for the latest updates or errata.
1. General Description
The RFM63B is a FSK and OOK transceiver module capable of operation at the 868 and 915 MHz license free ISM
frequency bands, It complies with both the relevant European and North American standards, EN 300-220 V2.1.1
(June 2006 release) and FCC Part 15 (10-1-2006 edition). A unique feature of this circuit is its extremely low
current consumption in receiver mode of only 3mA (typ).
1.1. Simplified Block Diagram
Figure 1: RFM63B Simplified Block Diagram
Page 5 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
1.2. Pin Diagram(TOP)
The following diagram shows the pins arrangement of the package, top view.
Page 6 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
AD1V.A3N.CPEiDnCDOMeMscUNriIpCAtiToIOnNS & SENSING
Table 2: RFM63B Pinouts
Number
Name
Type
Description
I/O
I
1
POR
POR. Do not connect if unused
SPI CONFIG enable
SPI DATA enable
2
NSS_CONFIG
NSS_DATA
MISO
I
3
O
I
4
SPI data output
5
MOSI
SPI data input
I
6
SCK
SPI clock input
O
I
7
CLKOUT
3.3V
Clock output
8
Supply voltage
I
9
GND
Exposed ground pad
Exposed ground pad
RF input/output
I
10
11
12
13
14
15
16
GND
I/O
I
ANA
GND
Exposed ground pad
NRZ data input and output (Continuous mode)
PLL lock detection output
Interrupt output
I/O
O
O
O
DATA
PLL_LOCK
IRQ_1
IRQ_0
Interrupt output
Page 7 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
2. Electrical Characteristics
2.1. ESD Notice
The RFM63B is a high performance radio frequency device. It satisfies:
•
Class 2 of the JEDEC standard JESD22-A114-B (Human Body Model).
•
Class III of the JEDEC standard JESD22-C101C (Charged Device Model) on all pins.
It should thus be handled with all the necessary ESD precautions to avoid any permanent damage.
2.2. Absolute Maximum Ratings
Stresses above the values listed below may cause permanent device failure. Exposure to absolute maximum
ratings for extended periods may affect device reliability.
Table 3: Absolute Maximum Ratings
Symbol
Descrip
tion
M
in
Max
Unit
VDDmr
Supply voltage
Storage temperature
Input level
-0
-55
-
.
3
3
125
0
.
7
V
°C
dBm
Tmr
P
mr
2.3. Operating Range
Table 4: Operating Range
Symbol
Descrip
tion
M
in
Max
Unit
VDDop
Supply Voltage
Temperature
Input Level
2
-20
-
.
1
3
.
6
V
°C
dBm
Trop
+
70
ML
0
2.4. Specification
Conditions: Temp = 25 °C, VDD = 3.3 V, , carrier frequency = 868 or 915 MHz, unless otherwise specified.
2.4.1. Power Consumption
Table 5: Power Consumption Specification
Symbol
Description
Conditions
M
in
Typ
Max
Unit
IDDSL
Supply current, Sleep mode
Supply current in standby
mode, CLKOUT disabled
-
0
.
1
2
µA
Crystal oscillator running(2)
IDDST
-
-
65
80
µA
Frequency synthesizer
running
IDDFS
IDDR
IDDT
Supply current in FS mode
Supply current in Rx mode
Supply current in Tx mode
1
.
.
3
0
1
.
.
7
5
mA
-
-
-
3
3
mA
mA
mA
Output power = +10 dBm
Output power = 1dBm(1)
25
16
30
21
(1) Guaranteed by design and characterization
(2) Crystal Cload=10pF, C0=2.5pF, Rm=15 Ohms
Page 8 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
2.4.2. Frequency Synthesis
Table 6: Frequency Synthesizer Specification
Symbol
Description
Conditions
868MHz Module
M
865
in
Typ
Max
871
Unit
MHz
FR
Frequency ranges
915MHz Module
912
1.56
1.56
33
918
200
32
MHz
Kb/s
Kb/s
kHz
BR_F
BR_O
FDA
Bit rate (FSK)
Bit rate (OOK)
NRZ
NRZ
-
-
Frequency deviation (FSK)
Crystal oscillator frequency
Frequency synthesizer
step
Oscillator wake-up time
Frequency synthesizer
wake-up time at most
10 kHz away from the
target
50
12.8
200
XTAL
MHz
For All Module
Variable, depending on the
frequency.
FSTEP
-
-
2
kHz
ms
-
TS_OSC
From Sleep mode(1)
1.
5
5
TS_FS
From Stby mode
-
500
µs
800
-
-
-
-
-
-
-
200 kHz step
1 MHz step
5 MHz step
7 MHz step
12 MHz step
20 MHz step
27 MHz step
-
-
-
-
-
-
-
180
200
250
260
290
320
340
µs
µs
µs
µs
µs
µs
µs
Frequency synthesizer hop
time at most 10 kHz away
from the target
TS_HOP
(1) Guaranteed by design and characterization
2.4.3. Transmitter
Table 7: Transmitter Specification
Symbol
Description
Conditions
M
in
Typ
Max
Unit
RF output power,
programmable with 8 steps
of typ. 3dB
Maximum power setting
-
+12
-
dBm
RFOP
Minimum power setting
-
-
-8
-
-
dBm
Measured with a 600 kHz
offset, at the transmitter
output.
PN
Phase noise
-110
dBc/Hz
At any offset between
200 kHz and 600 kHz,
unmodulated carrier, Fdev
= 50 kHz.
SPT
Transmitted spurious
-
-
-47
dBc
TS_TR(1)
Transmitter wake-up time
Transmitter wake-up time
From FS to Tx ready.
From Stby to Tx ready.
-
-
120
600
500
900
µs
µs
TS_TR2(1)
(1) Guaranteed by design and characterization
Page 9 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
2.4.4. Receiver
On the following table, fc and fo describe the bandwidth of the active channel filters as described in section 3.4.4.2.
All sensitivities are measured receiving a PN15 sequence, for a BER of 0.1.%
Table 8: Receiver Specification
Symbol
Description
Conditions
M
in
Typ
Max
Unit
868MHz, BR=25 kb/s, Fdev
=50 kHz, fc=100 kHz
868 MHz, BR=66.7 kb/s,
Fdev=100 kHz, fc=200 kHz
915 MHz, BR=25 kb/s,
Fdev=50 kHz, fc=100 kHz
915 MHz, BR = 66.7 kb/s,
Fdev=100 kHz, fc=200 kHz
868 MHz, 2kb/s NRZ
fc-fo=50 kHz, fo=50 kHz
868 MHz, 16.7 kb/s NRZ
fc-fo=100 kHz, fo=100 kHz
915 MHz, 2kb/s NRZ
fc-fo=50 kHz, fo=50 kHz
915 MHz, 16.7 kb/s NRZ
fc-fo=100 kHz, fo=100 kHz
Modulation as wanted signal
Offset = 300 kHz, unwanted
tone is not modulated
Offset = 600 kHz, unwanted
tone is not modulated
Offset = 1.2 MHz, unwanted
tone is not modulated
Offset = 1 MHz,
unmodulated
Offset = 2 MHz,
unmodulated, no SAW
Offset = 10 MHz,
unmodulated, no SAW
Single side BW
Polyphase Off
Single side BW
Polyphase On
Interferers at 1MHz and
1.950 MHz offset
From FS to Rx ready
From Stby to Rx ready
200 kHz step
-
-105
-
dBm
-
-
-
-
-
-
-101
-103
-99
-
-
-
-
-
-
dBm
dBm
dBm
dBm
dBm
dBm
RFS_F
Sensitivity (FSK)
-111
-104
-109
RFS_O
Sensitivity (OOK)
-
-
-
-103
-12
-
-
-
dBm
dBc
dB
CCR
ACR
Co-channel rejection
27
52
57
-48
-37
-33
-
Adjacent channel
rejection
-
-
-
-
-
-
-
-
-
-
dB
dB
dBm
dBm
dBm
kHz
kHz
dBm
BI
Blocking immunity
Receiver bandwidth in
FSK mode
RXBW_F(1,2)
RXBW_O(1,2)
IIP3
50
50
250
400
Receiver bandwidth in
OOK mode
-
Input 3rd order intercept
point
-
-
-
-
-
-
-
-
-
-
-
-
-28
280
600
400
400
460
480
520
550
600
-
-
TS_RE(1)
Receiver wake-up time
Receiver wake-up time
µs
µs
µs
µs
µs
µs
µs
µs
µs
s
500
900
-
-
-
-
-
-
TS_RE2(1)
1MHz step
5MHz step
Receiver hop time from
TS_RE_HOP
Rx ready to Rx ready with 7MHz step
a frequency hop
12MHz step
20MHz step
27MHz step
From Rx ready
Ranging from sensitivity
-
TS_RSSI
DR_RSSI
RSSI sampling time
RSSI dynamic Range
1/Fdev
-
70
dB
(1) Guaranteed by design and characterization
(2) This reflects the whole receiver bandwidth, as described in sections 3.4.4.1 and 3.4.4.2
Page 10 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
2.4.5. Digital Specification
Conditions: Temp = 25 °C, VDD = 3.3 V, unless otherwise specified.
Table 9: Digital Specification
Symbol
VIH
VIL
VOH
VOL
Description
Conditions
M
in
Typ
Max
-
0.2*VDD
Unit
V
V
V
V
Digital input level high
Digital input level low
Digital output level high
Digital output level low
0.8*VDD
-
-
-
-
-
Imax=1mA
Imax=-1mA
0.9*VDD
-
-
0.1*VDD
-
-
-
-
-
-
-
6
1
-
-
-
SCK_CONFIG SPI Config. clock frequency
MHz
MHz
µs
ns
SCK_DATA
T_DATA
SPI Data clock frequency
DATA hold and setup time
2
250
312
T_MOSI_C
T_MOSI_D
MOSI setup time for SPI Config.
MOSI setup time for SPI Data.
ns
NSS_CONFIG low to SCK rising edge.
SCK falling edge to NSS_CONFIG high.
NSS_DATA low to SCK rising edge.
SCK falling edge to NSS_DATA high.
NSS_CONFIG rising to falling edge.
NSS_DATA rising to falling edge.
T_NSSC_L
T_NSSD_L
ns
ns
500
-
-
-
625
500
625
-
-
T_NSSC_H
T_NSSD_H
-
-
ns
ns
-
Page 11 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3. Architecture Description
This section describes in depth the architecture of this ultra low-power transceiver:
VR_PA
RFIO
RQ_0
RQ_1
i
MOSI
l
M
SCK
ISO
NSS_CONFIG
SS_DATA
N
C
LKOUT
D
ATA
EST(8:0)
PLL_LOCK
I
XTAL_P
XTAL_M
I
Figure 3: RFM63B Detailed Block Diagram
3.1. Power Supply Strategy
To provide stable sensitivity and linearity characteristics over a wide supply range, the RFM63B is
internally regulated. This internal regulated power supply structure is described below:
Page 12 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
1ųF
Y5V
Vbat
VDD
—
2.1
—
3.6V
External Supply
Reg_top
1.4 V
Reg_dig
1.0 V
Reg_VCO
0.85 V
Biasing :
-SPI
Reg_ana
1.0 V
Reg_PA
1.80 V
-Config. Registers
-POR
Biasing analog
blocks
Biasing digital
blocks
Biasing :
Biasing :
-VCO circuit
-Ext. VCO
tank
-PA Driver
-PA choke
(ext)
1ųF
Y5V
220nF
X7R
100nF
X7R
47nF
X7R
Figure 4: Power Supply Breakdown
To ensure correct operation of the regulator circuit, the decoupling capacitor connection shown in Figure 4 is
required. These decoupling components are recommended for any design.
3.2. Frequency Synthesis Description
The frequency synthesizer of the RFM63B is a fully integrated integer-N type PLL. The PLL circuit requires only five
external components for the PLL loop filter and the VCO tank circuit.
3.2.1. Reference Oscillator
The RFM63B embeds a crystal oscillator, which provides the reference frequency for the PLL. The recommended
crystal specification is given in section 7.1.
3.2.2. CLKOUT Output
The reference frequency, or a sub-multiple of it, can be provided on CLKOUT by activating the bit
OSCParam_Clkout_on. The division ratio is programmed through bits OSCParam_Clkout_freq. The two
applications of the CLKOUT output are:
•
To provide a clock output for a companion uC, thus saving the cost of an additional oscillator. CLKOUT can be
made available in any operation mode, except Sleep mode, and is automatically enabled at power-up.
To provide an oscillator reference output. Measurement of the CLKOUT signal enables simple software
trimming of the initial crystal tolerance.
•
Note: To minimize the current consumption of the RFM63B, ensure that the CLKOUT signal is disabled when
unused.
Page 13 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.2.3. PLL Architecture
The crystal oscillator (XO) forms the reference oscillator of an Integer-N Phase Locked Loop (PLL), whose
operation is discussed in the following section. Figure 5 shows a block schematic of the RFM63B PLL. Here the
crystal reference frequency and the software controlled dividers R, P and S determine the output frequency of the
PLL.
VCO_M
VR_VCO
Figure 5: Frequency Synthesizer Description
The VCO tank inductors are connected on an external differential input. Similarly, the loop filter is also located
externally. However, there is an internal 8pF capacitance at VCO input that should be subtracted from the desired
loop filter capacitance.
The output signal of the VCO is used as the input to the local oscillator (LO) generator stage, illustrated in Figure 6.
The VCO frequency is subdivided and used in a series of up (down) conversions for transmission (reception).
LO1 Rx
Receiver
LOs
I
LO2 Rx
÷8
Q
I
90°
LO
VCO Output
LO1 Tx
LO2 Tx
Q
I
90°
90°
Transmitter
LOs
÷8
Q
Figure 6: LO Generator
3.2.4. PLL Tradeoffs
With an integer-N PLL architecture, the following criterion must be met to ensure correct operation:
The comparison frequency, Fcomp, of the Phase Frequency Detector (PFD) input must remain higher than six
times the PLL bandwidth (PLLBW) to guarantee loop stability and to reject harmonics of the comparison
frequency Fcomp. This is expressed in the inequality:
•
Fcomp
PLLBW
≤
6
•
•
However the PLLBW has to be sufficiently high to allow adequate PLL lock times
Because the divider ration R determines Fcomp, it should be set close to 119, leading to Fcomp≈100 kHz
which will ensure suitable PLL stability and speed.
Page 14 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
, the PLL prototype is the following:
•
•
•
•
64 ≤ R ≤ 169
S < P+1
PLLBW = 15 kHz nominal
Startup times and reference frequency spurs as specified.
3.2.5. Voltage Controlled Oscillator
The integrated VCO requires only two external tank circuit inductors. As the input is differential, the two inductors
should have the same nominal value. The performance of these components is important for both the phase noise
and the power consumption of the PLL. It is recommended that a pair of high Q factor inductors is selected. These
should be mounted orthogonally to other inductors (in particular the PA choke) to reduce spurious coupling
between the PA and VCO. In addition, such measures may reduce radiated pulling effects and undesirable
transient behavior, thus minimizing spectral occupancy. Note that ensuring a symmetrical layout of the VCO
inductors will further improve PLL spectral purity.
For best performance wound type inductors, with tight tolerance, should be used as described in section 7.5.3.
3.2.5.1. SW Settings of the VCO
To guarantee the optimum operation of the VCO over the RF63‟s frequency and temperature ranges, the
following settings should be programmed into the RF63:
Target
(MHz)
Freq_band
c
h
a
nn
e
l
863-
870
10
902-
915
00
915-
928
01
950-
960
10
Table 10: MCParam_Freq_band Setting
3.2.5.2. Trimming the VCO Tank by Hardware and Software
To ensure that the frequency band of operation may be accurately addressed by the R, P and S dividers of the
synthesizer, it is necessary to ensure that the VCO is correctly centered. Note that for the reference design (see
section 7.5) no centering is necessary. However, any deviation from the reference design may require the
optimization procedure, outlined below, to be implemented. This procedure is simplified thanks to the built-in VCO
trimming feature which is controlled over the SPI interface. This tuning does not require any RF test equipment,
and can be achieved by simply measuring Vtune, the voltage between pin LFM and LFP.
The VCO is centered if the voltage is within the range:
≤
150
50
≤
Vtune(mV
)
Note that this measurement should be conducted when in transmit mode at the center frequency of the desired
band (for example ~867 MHz in the 863-870 MHz band), with the appropriate MCParam_Freq_band setting.
If this inequality is not satisfied then adjust the MCParam_VCO_trim bits from 00 whilst monitoring Vtune. This
allows the VCO voltage to be trimmed in + 60 mV increments. Should the desired voltage range be inaccessible,
the voltage may be adjusted further by changing the tank circuit inductance value. Note that an increase in
inductance will result in an increase Vtune.
Page 15 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Note for mass production: The VCO capacitance is piece to piece dependant. As such, the optimization proposed
above should be verified on several prototypes, to ensure that the population is centered on 100 mV.
3.2.6. PLL Loop Filter
To adequately reject spurious components arising from the comparison frequency Fcomp, an external 2nd order
loop filter is employed.
RL1
LF_M
CL2
CL1
LF_P
Figure 7: Loop Filter
Following the recommendations made in section 3.2.4, the loop filter proposed in the reference design‟s bill of
material on section 7.5.3 should be used. The loop filter settings are frequency band independent and are hence
relevant to all implementations of the RFM63B.
3.2.7. PLL Lock Detection Indicator
The RFM63B also features a PLL lock detect indicator. This is useful for optimizing power consumption, by
adjusting the synthesizer wake up time (TS_FS), since the PLL startup time is lower than specified under nominal
conditions. The lock status can be read on bit IRQParam_PLL_lock, and must be cleared by writing a “1” to this
same register. In addition, the lock status can be reflected in pin
IRQParam_Enable_lock_detect.
PLL_LOCK, by setting the bit
3.2.8. Frequency Calculation
As shown in Figure 5 the PLL structure comprises three different dividers, R, P and S, which set the output
frequency through the LO. A second set of dividers is also available to allow rapid switching between a pair of
frequencies: R1/P1/S1 and R2/P2/S2. These six dividers are programmed by six bytes of the register MCParam
from addresses 6 to 11.
3.2.8.1. FSK Mode
The following formula gives the relationship between the local oscillator, and R, P and S values, when using FSK
modulation.
3.2.8.2. OOK Mode
Due to the manner in which the baseband OOK symbols are generated, the signal is always offset by the FSK
frequency deviation (Fdev - as programmed in MCParam_Freq_dev). Hence, the center of the transmitted OOK
signal is:
Page 16 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Consequently, in receive mode, due to the low intermediate frequency (Low-IF) architecture of the RFM63B
the frequency should be configured so as to ensure the correct low-IF receiver baseband center frequency, IF2.
Note that from Section 3.4.4, it is recommended that IF2 be set to 100 kHz.
Page 17 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.3. Transmitter Description
The RFM63B is set to transmit mode when MCParam_Chip_mode = 100.
3.3.1. Architecture Description
The baseband I and Q signals are digitally generated by a DDS whose digital to analog converters (DAC) followed
by two anti-aliasing low-pass filters transform the digital signal into analog in-phase (I) and quadrature (Q)
components whose frequency is the selected frequency deviation (Fdev).
1
Fdev
I(t)
Q(t)
Figure 9: I(t), Q(t) Overview
In FSK mode, the relative phase of I and Q is switched by the input data between -90° and +90° with co ntinuous
phase. The modulation is therefore performed at this initial stage, since the information contained in the phase
difference will be converted into a frequency shift when the I and Q signals are up-converted in the first mixer
stage. This first up-conversion stage is duplicated to enhance image rejection. The FSK convention is such that:
Page 18 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
In OOK mode, the phase difference between the I and Q channels is kept constant (independent of the transmitted
data). Thus, the first stage of up-conversion creates a fixed frequency signal at the low IF = Fdev (This explains
why the transmitted OOK spectrum is offset by Fdev).
OOK Modulation is accomplished by switching on and off the PA and PA regulator stages. By convention:
DATA= ''1'' PAon
''0'' PAoff
DATA=
After the interpolation filters, a set of four mixers combines the I and Q signals and converts them into a pair of
complex signals at the second intermediate frequency, equal to 1/8 of the LO frequency, or 1/9 of the RF
frequency. These two new I and Q signals are then combined and up-converted to the final RF frequency by two
quadrature mixers fed by the LO signal. The signal is pre-amplified, and then the transmitter output is driven by a
final power amplifier stage.
3.3.2. Bit Rate Setting
In Continuous transmit mode, setting the Bit Rate is useful to determine the frequency of DCLK. As explained in
section 5.3.2, DCLK will trigger an interrupt on the uC each time a new bit has to be transmitted.
3.3.3. Alternative Settings
Bit rate, frequency deviation and TX interpolation filter settings are a function of the reference oscillator crystal
frequency, FXTAL. Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of
the correct reference oscillator frequency. Please contact your local Semtech representative for further details.
3.3.4. Fdev Setting in FSK Mode
The frequency deviation, Fdev, of the FSK transmitter is programmed through bits MCParam_Freq_dev:
For correct operation the modulation index ß should be such that:
It should be noted that for communications between a pair of RFM63Bs, that Fdev should be at least 33 kHz to
ensure a correct operation on the receiver side.
3.3.5. Fdev Setting in OOK Mode
Fdev has no physical meaning in OOK transmit mode. However, as has been shown - due to the DDS baseband
signal generation, the OOK signal is always offset by “-Fdev” (see formulas is section 3.2.8). It is suggested that
Fdev retains its default value of 100 kHz in OOK mode.
Page 19 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.3.6. Interpolation Filter
After digital to analog conversion, both I and Q signals are smoothed by interpolation filters. This block low-pass
filters the digitally generated signal, and prevents the alias signals from entering the modulators. Its bandwidth can
be programmed with the register RXParam_InterpFiltTx, and should be set to:
Where Fdev is the programmed frequency deviation as set in MCParam_Freq_dev, and BR is the physical Bit Rate
of transmission.
Notes:
•
Low interpolation filter bandwidth will attenuate the baseband I/Q signals thus reducing the power of the FSK
signal. Conversely, excessive bandwidth will degrade spectral purity.
•
For the wideband FSK modulation, for example when operating in DTS mode, the recommended filter setting
can not be reached. However, the impact upon spectral purity will be negligible, due to the already wideband
channel.
3.3.7. Power Amplifier
The Power Amplifier (PA) integrated in the RFM63B operates under a regulated voltage supply of 1.8 V. The
external PA choke inductor is biased by an internal regulator output made available on VR_PA. Thanks to these
features, the PA output power is consistent over the power supply range. This is important for mobile applications
where this allows both predictable RF performance and battery life.
3.3.7.1. Rise and Fall Times Control
In OOK mode, the PA ramp times can be accurately controlled through the MCParam_PA_ramp register. Those
bits directly control the slew rate of VR_PA output .
Table 11: PA Rise/Fall Times
MCParam_PA_ramp
tVR_PA
3 us
8.5 us
15 us
23 us
tPA_OUT (rise / fall)
2.5 / 2 us
5 / 3 us
10 / 6 us
20 / 10 us
00
01
10
11
Page 20 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
DATA
VR_PA
[V]
95 %
95 %
tVR_PA
tVR_PA
PA Output
power
60 dB
60 dB
tPA_OUT
tPA_OUT
Figure 10: PA Control
3.3.7.2. Optimum Load Impedance
As the PA and the LNA front-ends in the RFM63B share the same Input/Output pin, they are internally matched
to approximately 50 Ω.
Pmax-1dB circle
M
ax Power
Z
opt = 30+j25 Ω
Figure 11: Optimal Load Impedance Chart
Please refer to the reference design section for an optimized PA load setting.
Page 21 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.3.7.3. Suggested PA Biasing and Matching
The recommended PA bias and matching circuit is illustrated below:
VR_PA
47nF
100nH
Antenna
port
SAW
PA
RFIO
DC block
Low-pass and DC block
Figure 12: Recommended PA Biasing and Output Matching
Please refer to section 7.5.3 of this document for the optimized matching arrangement for each frequency band.
3.3.8. Common Input and Output Front-End
The receiver and the transmitter share the same RFIO pin . Figure 13 below shows the configuration of the
common RF front-end.
•
In transmit mode, the PA and the PA regulator are active, with the voltage on the VR_PA pin equal to the
nominal voltage of the regulator (1.8 V). The external inductance is used to bias the PA.
In receive mode, both PA and PA regulator are off and VR_PA is tied to ground. The external inductance LT1
is then used to bias the LNA.
•
VR_PA
RFIO
To
Antenna
Figure 13: Front-end Description
Page 22 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.4. Receiver Description
The RFM63B is set to receive mode when MCParam_Chip_mode = 011.
3.4.1. Architecture
The RFM63B receiver employs a super-heterodyne architecture. Here, the first IF is 1/9th of the RF frequency
(approximately 100MHz). The second down-conversion down-converts the I and Q signals to base band in the
case of the FSK receiver (Zero IF) and to a low-IF (IF2) for the OOK receiver.
After the second down-conversion stage, the received signal is channel-select filtered and amplified to a level
adequate for demodulation. Both FSK and OOK demodulation are available. Finally, an optional Bit Synchronizer
(BitSync) is provided, to be supply a synchronous clock and data stream to a companion uC in Continuous mode,
Page 23 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
or to fill the FIFO buffers with glitch-free data in Buffered mode. The operation of the receiver is now described in
detail.
Note: Image rejection is achieved by the SAW filter.
3.4.2. LNA and First Mixer
In receive mode, the RFIO pin is connected to a fixed gain, common-gate, Low Noise Amplifier (LNA). The
performance of this amplifier is such that the Noise Figure (NF) of the receiver can be estimated to be ≈7 dB.
3.4.3. IF Gain and Second I/Q Mixer
Following the LNA and first down-conversion, there is an IF amplifier whose gain can be programmed from -
13.5 dB to 0 dB in 4.5 dB steps, via the register MCParam_IF_gain. The default setting corresponds to 0 dB gain,
but lower values can be used to increase the RSSI dynamic range. Refer to section 3.4.7 for additional information.
3.4.4. Channel Filters
The second mixer stages are followed by the channel select filters. The channel select filters have a strong
influence on the noise bandwidth and selectivity of the receiver and hence its sensitivity. Each filter comprises a
passive and active section.
3.4.4.1. Passive Filter
Each channel select filter features a passive second-order RC filter, with a bandwidth programmable through the
bits RXParam_PassiveFilt. As the wider of the two filters, its effect on the sensitivity is negligible, but its bandwidth
has to be setup instead to optimize blocking immunity. The value entered into this register sets the single side
bandwidth of this filter. For optimum performance it should be set to 3 to 4 times the cutoff frequency of the active
Butterworth (or polyphase) filter described in the next section.
3.4.4.2. A
The ‟fine‟ channel selection is performed by an active, third-order, Butterworth filter, which acts as a low-pass filter
for the zero-IF configuration (FSK), or a complex polyphase filter for the Low-IF (OOK) configuration. The
RXParam_PolypFilt_on bit enables/disables the polyphase filter.
Low-pass filter for FSK
( RXParam_PolyFilt_on=‟‟0‟‟)
-fC
fC
frequency
0
Polyphase filter for OOK
( RXParam_PolyFilt_on=‟‟1‟‟ )
Canceled side of
the polyphase filter
frequency
-fo
0
-fC
Figure 17: Active Channel Filter Description
Page 24 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
As can be seen from Figure 17, the required bandwidth of this filter varies between the two demodulation modes.
FSK mode: The 99% energy bandwidth of an FSK modulated signal is approximated to be:
•
The bits RXParam_ButterFilt set fc, the cutoff frequency of the filter. As we are in a Zero-IF configuration, the FSK
lobes are centered around the virtual “DC” frequency. The choice of fc should be such that the modulated signal
falls in the filter bandwidth, anticipating the Local Oscillator frequency drift over the operating temperature and
aging of the device:
Please refer to the charts in section 3.4.5 for an accurate overview of the filter bandwidth vs. setting.
•
OOK mode: The 99% energy bandwidth of an OOK modulated signal is approximated to be:
The bits RXParam_PolypFilt_center set fo, the center frequency of the polyphase filter when activated. fo should
always be chosen to be equal to the low Intermediate Frequency of the receiver (IF2). This is why, in the GUI
described in section 7.2.1 of this document, the low IF frequency of the OOK receiver denoted IF2 has been
replaced by fo.
The following setting is recommended:
The value stored in RXParam_ButterFilt determines fc, the filter cut-off frequency. So the user should set fc
according to:
Again, fc as a function of RXParam_ButterFilt is given in the section 3.4.6.
3.4.5. Channel Filters Setting in FSK Mode
Fc, the 3dB cutoff frequency of the Butterworth filter used in FSK reception, is programmed through the bit
RXParam_ButterFilt. However, the whole receiver chain influences this cutoff frequency. Thus the channel select
and resultant filter bandwidths are summarized in the following chart:
Page 25 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Actual
BW
Theoretical
BW
Butterworth Filter's BW, FSK
450
400
350
300
250
200
150
100
50
0
0
2
4
6
8
10
12
14
16
Val (RXParam_ButterFilt) [d]
Figure 18: Butterworth Filter's Actual BW
Table 37 suggests filter settings in FSK mode, along with the corresponding passive filter bandwidth and the
accepted tolerance on the crystal reference.
3.4.6. Channel Filters Setting in OOK Mode
The center frequency, fo, is always set to 100kHz. The following chart shows the receiver bandwidth when
changing RXParam_Butterfilt bits, whilst the polyphase filter is activated.
Actual
BW
Theoretical
BW
Polyphase Filter's BW, OOK
450
400
350
300
250
200
150
100
50
0
0
2
4
6
8
10
12
14
16
Val (RXParam_ButterFilt [d]
RXParam_PolypFilt="0011"
Figure 19: Polyphase Filter's Actual BW
Table 38 suggests a few filter settings in OOK mode, along with the corresponding passive filter bandwidth and the
accepted tolerance on the crystal reference.
3.4.7. RSSI
After filtering, the In-phase and Quadrature signals are amplified by a chain of 11 amplifiers, each with 6dB gain.
The outputs of these amplifiers are used to evaluate the Received Signal Strength (RSSI).
3.4.7.1. Resolution and Accuracy
Whilst the RSSI resolution is 0.5 dB, the absolute accuracy is not expected to be better than +/- 3dB due to process
and external component variation. Higher accuracy whilst performing absolute RSSI measurements will require
additional calibration.
3.4.7.2. Acquisition Time
Page 26 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
In OOK mode, the RSSI evaluates the signal strength by sampling I(t) and Q(t) signals 16 times in each period of
the chosen IF2 frequency (refer to section 3.4.1). In FSK mode, the signals are sampled 16 times in each Fdev
period, Fdev being the frequency deviation of the companion transmitter. An average is then performed over a
sliding window of 16 samples. Hence, the RSSI output register RXParam_RSSI is updated 16 times in each Fdev
or IF2 period.
The following settings should be respected:
•
FSK Mode: Ensure that the Fdev parameter (as described in MCParam_Fdev) remains consistent with the
actual frequency deviation of the companion transmitter.
•
OOK reception: Ensure that the Fdev parameter (as described in MCParam_Fdev) is equal with the frequency
of I(t) and Q(t) signals, i.e. the second Intermediate Frequency, IF2, of the receiver (Note that this equals Fo,
the center frequency of the polyphase filter).
3.4.7.3. Dynamic Range
The dynamic range of the RSSI is over 70 dB, extending from the nominal sensitivity level. The IF gain setting
available in MCParam_IF_gain is used to achieve this dynamic range:
RSSI Response
180
160
140
120
100
80
60
40
20
0
-120
-100
-80
-60
-40
-20
0
Pin [dBm]
IF_Gain=00
IF_Gain=01
IF_Gain=10
IF_Gain=11
Figure 20: RSSI Dynamic Range
The RSSI response versus input signal is independent of the receiver filter bandwidth. However in the absence of
any input signal, the minimum value directly reflects upon the noise floor of the receiver, which is dependant on the
filter bandwidth of the receiver.
3.4.7.4. RSSI IRQ Source
The RFM63B can also be used to detect a RSSI level above a pre-configured threshold. The threshold is set
in
IRQParam_RSSI_irq_thresh and the IRQ status stored in IRQParam_RSSI_irq (cleared by writing a “1”).
An interrupt can be mapped to the IRQ0 or IRQ1 pins via bits IRQParam_Rx_stby_irq0 or
IRQParam_Rx_stby_irq1. Figure 21 shows the timing diagram of the RSSI interrupt source, with
IRQParam_RSSI_irq_thresh set to 28.
Page 27 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
24 26 27 30 25 20 20 20 18 22 33 20 22 34 33
RXParam_RSSI_val(7:0)
IRQParam_RSSI_irq
Clear interrupt
Figure 21: RSSI IRQ Timings
3.4.8. Fdev Setting in Receive Mode
The effect of the Fdev setting is different between FSK and OOK modes:
3.4.8.1. FSK Rx Mode
In FSK mode the Fdev setting, as configured by MCParam_Freq_Dev, sets sampling frequencies on the receiver.
The user should make it consistent with the frequency deviation of the FSK signal that is received.
3.4.8.2. OOK Rx Mode
The frequency deviation Fdev, as described above, sets the sampling rate of the RSSI block. It is therefore
necessary to set Fdev to the recommended low-IF frequency, IF2, of 100 kHz:
3.4.9. FSK Demodulator
The FSK demodulator provides data polarity information, based on the relative phase of the input I and Q signals at
the baseband. Its outputs can be fed to the Bit Synchronizer to recover the timing information. The user can also
use the raw, unsynchronized, output of the FSK demodulator in Continuous mode.
The FSK demodulator of the RFM63B operates most effectively for FSK signals with a modulation index
greater than or equal to two:
3.4.10. OOK Demodulator
The OOK demodulator performs a comparison of the RSSI output and a threshold value. Three different threshold
modes are available, programmed through the RXParam_OOK_thresh_type register.
The recommended mode of operation is the “Peak” threshold mode, illustrated below in Figure 22:
Page 28 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
RSSI
(dB)
„‟Peak -6dB‟‟ Threshold
„‟Floor‟‟ threshold defined by
MCParam_OOK_floor_thresh
Noise floor of
receiver
Time
Zoom
Decay in dB as defined in
RXPAram_OOK_thresh_step
Fixed 6dB difference
Period as defined in
RXParam_OOK_thresh_dec_period
Figure 22: OOK Demodulator Description
In peak threshold mode the comparison threshold level is the peak value of the RSSI, reduced by 6dB. In the
absence of an input signal or during the reception of a logical “0”, the acquired peak value is decremented by one
RXPAram_OOK_thresh_step every RXParam_OOK_thresh_dec_period.
When the RSSI output is null for a long time (for instance after a long string of “0” received, or if no transmitter is
present), the peak threshold level will continue falling until it reaches the “Floor Threshold” that is programmed
through the register MCParam_OOK_floor_thresh.
The default settings of the OOK demodulator lead to the performance stated in the electrical specification.
However, in applications in which sudden signal drops are awaited during a reception, the three parameters shall
be optimized accordingly.
3.4.10.1. Optimizing the Floor Threshold
MCParam_OOK_floor_thres determines the sensitivity of the OOK receiver, as it sets the comparison threshold for
weak input signals (i.e. those close to the noise floor). Significant sensitivity improvements can be generated if
configured correctly.
Note that the noise floor of the receiver at the demodulator input depends on:
•
•
•
•
The noise figure of the receiver.
The gain of the receive chain from antenna to base band.
The matching - including SAW filter.
The bandwidth of the channel filters.
It is therefore important to note that the setting of MCParam_OOK_floor_thresh will be application dependant. The
following procedure is recommended to optimize MCParam_OOK_floor_thresh.
Page 29 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Set RFM63B in OOK Rx mode Adjus
Bit Rate, Channel filter BW Default
RXParam_OOK_thresh setting No
input signal
t
Continuous Mode
Monitor DATA pin
Increment
MCParam_OOK_floor_thres
Glitch activity
on DATA
?
Optimization complete
Figure 23: Floor Threshold Optimization
The new floor threshold value found during this test should be the value used for OOK reception with those receiver
settings.
Note that if the output signal on DATA is logic “1”, the value of MCParam_OOK_floor_thres is below the noise floor
of the receiver chain. Conversely, if the output signal on DATA is logic “1”, the value of MAParam_floor_thres is
several dB above the noise floor.
3.4.10.2. Optimizing OOK Demodulator Response for Fast Fading Signals
A sudden drop in signal strength can cause the bit error rate to increase. For applications where the expected
signal drop can be estimated the following OOK demodulator parameters RXParam_OOK_thresh_step and
RXParam_OOK_thresh_dec_period can be optimized as described below for a given number of threshold
decrements per bit RXParam_OOK_thresh_dec_period:
•
•
•
•
•
•
•
•
000
001
010
011
100
101
110
111
once in each chip period (d)
once in 2 chip periods
once in 4 chip periods
once in 8 chip periods
twice in each chip period
4 times in each chip period
8 times in each chip period
16 times in each chip period
For each decrement of RXParam_OOK_thresh_step:
•
•
•
•
•
•
•
•
000
001
010
011
100
101
110
111
0.5 dB (d)
1.0 dB
1.5 dB
2.0 dB
3.0 dB
4.0 dB
5.0 dB
6.0 dB
Page 30 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
3.4.10.3. Alternative OOK Demodulator Threshold Modes
In addition to the Peak OOK threshold mode, the user can alternatively select two other types of threshold
detectors:
•
Fixed threshold: The value is selected through the MCParam_OOK_floor_thresh register (refer to section
3.4.10.1 for further information concerning optimization of the floor threshold).
•
Average threshold: Data supplied by the RSSI block is averaged with the following cutoff frequency:
In the first example, the higher cut-off frequency enables a sequence of up to 8 consecutive “0” or “1” to be
supported, whilst the lower cut-off frequency presented in the second example allows for the correct reception of up
to 32 consecutive “0” or “1”.
3.4.11. Bit Synchronizer
The Bit Synchronizer (BitSync) is a block that provides a clean and synchronized digital output, free of glitches.
Raw demodulator
output
(FSK or OOK)
DATA
BitSync Output To
pin DATA and
DCLK in continuous
mode
DCLK
IRQ_1
Figure 24: BitSync Description
The BitSync can be disabled through the bits RXParam_Bitsync_off, and by holding pin IRQ1 low. However, for
optimum receiver performance, its use when running Continuous mode is strongly advised. With this option a
DCLK signal is present on pin IRQ_1.
The BitSync is automatically activated in Buffered and Packet modes. The bit synchronizer bit-rate is controlled by
MCParam_BR. For a given bit rate, this parameter is determined by:
Page 31 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
For proper operation, the Bit Synchronizer must first receive three bytes of alternating logic value preamble, i.e.
“0101” sequences. After this startup phase, the rising edge of DCLK signal is centered on the demodulated bit.
Subsequent data transitions will preserve this centering.
This has two implications:
•
Firstly, if the Bit Rates of Transmitter and Receiver are known to be the same, the RFM63B will be able to
receive an infinite unbalanced sequence (all “0s” or all ”1s”) with no restriction.
•
If there is a difference in Bit Rate between Tx and Rx, the amount of adjacent bits at the same level that the
BitSync can withstand can be estimated as:
This implies approximately 6 consecutive unbalanced bytes when the Bit Rate precision is 1%, which is easily
achievable (crystal tolerance is in the range of 50 to 100 ppm).
3.4.12. Alternative Settings
Bit Synchronizer and Active channel filter settings are a function of the reference oscillator crystal frequency, FXTAL
.
Settings other than those programmable with a 12.8 MHz crystal can be obtained by selection of the correct
reference oscillator frequency. Please contact your local Semtech representative for further details.
3.4.13. Data Output
After OOK or FSK demodulation, the baseband signal is made available to the user on , DATA, when
Continuous mode is selected.
In Buffered and Packet modes, the data is retrieved from the FIFO through the SPI interface.
Page 32 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
4. Operating Modes
This section summarizes the settings for each operating mode of the RFM63B, and explains the
functionality available and the timing requirements for switching between modes.
4.1. Modes of Operation
Table 12: Operating Modes
Mode
MCParam_Chip_mode
Active blocks
Sleep
Standby
000
001
SPI, POR
SPI, POR, Top regulator, digital regulator, XO, CLKOUT (if activated through
OSCParam_Clkout)
FS
Receive
010
011
Same + VCO regulator, all PLL and LO generation blocks
Same as FS mode + LNA, first mixer, IF amplifier, second mixer set, channel
filters, baseband amplifiers and limiters, RSSI, OOK or FSK demodulator,
BitSync and all digital features if enabled
Transmit
100
Same as FS mode + DDS, Interpolation filters, all up-conversion mixers, PA
driver, PA and external VR_PA pin output for PA choke.
4.2. Digital Pin Configuration vs. Chip Mode
Table 13 describes the state of the digital IOs in each of the above described modes of operation, regardless of the
data operating mode (Continuous, Buffered, or Packet).
Table 13: Pin Configuration vs. Chip Mode
Chip
……….Mode
Sleep
mode
Standby
mode
Receive
mode
Transmit
mode
FS mode
Comment
Pin
NSS_CONFIG has the priority over
NSS_DATA
NSS_CONFIG Input
Input
Input
Input
Input
Input
Input
Input
Input
NSS_DATA
MISO
Input
Input
Output only if NSS_CONFIG or
NSSDATA=‟0‟
Input
Input
Input
Input
MOSI
Input
Input
Input
Input
Input
SCK
Input
Input
Input
Input
Input
IRQ_0
IRQ_1
DATA
CLKOUT
PLL_LOCK
High-Z
High-Z
Input
High-Z
High-Z
Output (1)
Output (1)
Input
Output
Output (2)
Output (1)
Output (1)
Input
Output
Output (2)
Output
Output
Output
Output
Output (2)
Output
Output
Input
Output
Output (2)
Notes:
(1): High-Z if Continuous mode is activated, else Output
(2): Output if PLL_lock_en = 1, else High-Z
(3): Valid logic states must be applied to inputs at all times to avoid unwanted leakage currents
Page 33 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5. Data Processing
5.1. Overview
5.1.1. Block Diagram
Figure 25, illustrates the RFM63B data processing circuit. Its role is to interface the data to/from the
modulator/demodulator and the uC access points (SPI, IRQ and DATA pins). It also controls all the configuration
registers.
The circuit contains several control blocks which are described in the following paragraphs.
RFM63B
Tx/Rx
DATA
RQ_0
RQ_1
I
CONTROL
I
SP
I
Rx
Tx
Data
SYNC
RECOG
.
CONFIG
PACKET
HANDLER
F
I
FO
(+SR)
NSS_DATA
SCK
DATA
MOS
I
MI
SO
Figure 25: RFM63B’s Data Processing Conceptual View
The RFM63B implements several data operation modes, each with their own data path through the data
processing section. Depending on the data operation mode selected, some control blocks are active whilst others
remain disabled.
5.1.2. Data Operation Modes
The RFM63B has three different data operation modes selectable by the user:
•
Continuous mode: each bit transmitted or received is accessed in real time at the DATA pin. This mode may be
used if adequate external signal processing is available.
•
Buffered mode: each byte transmitted or received is stored in a FIFO and accessed via the SPI bus. uC
processing overhead is hence significantly reduced compared to Continuous mode operation. The packet
length is unlimited.
•
Packet mode (recommended): user only provides/retrieves payload bytes to/from the FIFO. The packet is
automatically built with preamble, Sync word, and optional CRC, DC free encoding and the reverse operation is
performed in reception. The uC processing overhead is hence reduced further compared to Buffered mode.
The maximum payload length is limited to the maximum FIFO limit of 64 bytes
Page 34 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Table 14: Data Operation Mode Selection
MCParam_Data_mode
Data Operation Mode
Continuous
00
01
1x
Buffered
P
acket
Each of these data operation modes is described fully in the following sections.
5.2. Control Block Description
5.2.1. SPI Interface
5.2.1.1. Overview
As illustrated in the Figure 26 below, the RFM63B‟s SPI interface consists of two sub blocks:
•
•
SPI Config: used in all data operation modes to read and write the configuration registers which control all the
parameters of the chip (operating mode, bit rate, etc...)
SPI Data: used in Buffered and Packet mode to write and read data bytes to and from the FIFO. (FIFO
interrupts can be used to manage the FIFO content.)
RFM63B
NSS_CONFIG
MOSI
Config.
SP
CONF
(slave)
I
MOSI
MISO
SCK
Regis ers
t
I
G
MISO
SCK
NSS_DATA
µ
C
(master)
SPI
FIFO
DATA
(slave)
NSS_DATA
Figure 26: SPI Interface Overview and uC Connections
Both interfaces are configured in slave mode whilst the uC is configured as the master. They have separate
selection pins (NSS_CONFIG and NSS_DATA) but share the remaining pins:
•
•
•
SCK (SPI Clock): clock signal provided by the uC
MOSI (Master Out Slave In): data input signal provided by the uC
MISO (Master In Slave Out): data output signal provided by the RFM63B
As described below, only one interface can be selected at a time with NSS_CONFIG having the priority:
Page 35 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Table 15: Config vs. Data SPI Interface Selection
NSS_DATA
NSS_CONFIG SPI Interface
0
0
1
1
0
1
0
1
Config
Data
Config
None
The following paragraphs describe how to use each of these interfaces.
5.2.1.2. SPI Config
•
Write Register
To write a value into a configuration register the timing diagram below should be carefully followed by the uC.
The register‟s new value is effective from the rising edge of NSS_CONFIG.
10
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
NSS_CONFIG (In)
SCK (In)
New value at
address A1
MOSI (In)
A(4) A(3) A(2) A(1) A(0) stop D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0)
Current value at
start rw
Address = A1
address A1*
x
x
MISO (Out)
x
x
x
x
x
x
D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0)
HZ
HZ
(input)
(input)
* when writing the new value at address A1, the current content of A1 can be read by the uC.
(In)/(Out) refers to RFM63B side
Figure 27: Write Register Sequence
Note that when writing more than one register successively, it is not compulsory to toggle NSS_CONFIG back high
between two write sequences. The bytes are alternatively considered as address and value. In this instance, all
new values will become effective on rising edge of NSS_CONFIG.
•
Read Register
To read the value of a configuration register the timing diagram below should be carefully followed by the uC.
Page 36 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
10
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
NSS_CONFIG (In)
SCK (In)
MOSI (In)
x
x
x
x
x
x
x
x
start rw
A(4) A(3) A(2) A(1) A(0) stop
Address = A1
Current value at
address A1
x
x
MISO (Out)
x
x
x
x
x
x
D(7) D(6) D(5) D(4) D(3) D(2) D(1) D(0)
HZ
(input
HZ
(input)
Figure 28: Read Register Sequence
Note that when reading more than one register successively, it is not compulsory to toggle NSS_CONFIG back
high between two read sequences. The bytes are alternatively considered as address and value.
5.2.1.3. SPI Data
•
Write Byte (before/during Tx)
To write bytes into the FIFO the timing diagram below should be carefully followed by the uC.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
NSS_DATA (In)
SCK (In)
1st byte written
2nd byte written
MOSI (In)
D1(0)
D2(7) D2(6) D2(5) D2(4) D2(3) D2(2) D2(1) D2(0)
D1(7) D1(6) D1(5) D1(4) D1(3) D1(2) D1(1)
x
MISO (Out)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
HZ
HZ
HZ
(input)
(input)
(input)
Figure 29: Write Bytes Sequence (ex: 2 bytes)
Note that it is compulsory to toggle NSS_DATA back high between each byte written.
The byte is pushed into the FIFO on the rising edge of NSS_DATA
Page 37 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
•
Read Byte (after/during Rx)
To read bytes from the FIFO the timing diagram below should be carefully followed by the uC.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
NSS_DATA (In)
SCK (In)
MOSI (In)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
2nd byte read
1st byte read
MISO (Out)
D1(7)
D1(6) D1(5)
D1(4) D1(3)
D1(2) D1(1) D1(0)
D2(7) D2(6) D2(5) D2(4)
D2(3) D2(2) D2(1) D2(0)
HZ
(input)
HZ
(input)
HZ
(input)
Figure 30: Read Bytes Sequence (ex: 2 bytes)
Note that it is compulsory to toggle NSS_DATA back high between each byte read.
5.2.2. FIFO
5.2.2.1. Overview and Shift Register (SR)
In Buffered and Packet modes of operation, both data to be transmitted and that has been received are stored in a
configurable FIFO (First In First Out) device. It is accessed via the SPI Data interface and provides several
interrupts for transfer management.
The FIFO is 1 byte (8 bits) wide hence it only performs byte (parallel) operations, whereas the demodulator
functions serially. A shift register is therefore employed to interface the two devices. In transmit mode it takes bytes
from the FIFO and outputs them serially (MSB first) at the programmed bit rate to the modulator. Similarly, in Rx the
shift register gets bit by bit data from the demodulator and writes them byte by byte to the FIFO. This is illustrated in
figure below.
FIFO
by
t
e1
e0
byt
8
Data T
x/
Rx
SR (8bits)
1
MSB
LSB
Figure 31: FIFO and Shift Register (SR)
5.2.2.2. Size Selection
The FIFO width is programmable, to 16, 32, 48 or 64 bytes via MCParam_Fifo_size
Page 38 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.2.2.3. Interrupt Sources and Flags
All interrupt sources and flags are configured in the IRQParam section of the configuration register, with the
exception of Fifo_threshold :
•
/Fifoempty: /Fifoempty interrupt source is low when byte 0, i.e. whole FIFO, is empty. Otherwise it is high. Note
that when retrieving data from the FIFO, /Fifoempty is updated on NSS_DATA falling edge, i.e. when
/Fifoempty is updated to low state the currently started read operation must be completed. In other words,
/Fifoempty state must be checked after each read operation for a decision on the next one (/Fifoempty = 1:
more byte(s) to read; /Fifoempty = 0: no more byte to read).
•
Write_byte: Write_byte interrupt source goes high for 1 bit period each time a new byte is transferred from the
SR to the FIFO (i.e. each time a new byte is received)
•
•
Fifofull: Fifofull interrupt source is high when the last FIFO byte, i.e. the whole FIFO, is full. Otherwise it is low.
Fifo_overrun_clr: Fifo_overrun_clr flag is set when a new byte is written by the user (in Tx or Standby modes)
or the SR (in Rx mode) while the FIFO is already full. Data is lost and the flag should be cleared by writing a 1,
note that the FIFO will also be cleared.
•
•
Tx_done: Tx_done interrupt source goes high when FIFO is empty and the SR‟s last bit has been send to the
modulator (i.e. the last bit of the packet has been sent). One bit period delay is required after the rising edge of
Tx_done to ensure correct RF transmission of the last bit. In practice this may not require special care in the uC
software due to IRQ processing time.
Fifo_threshold: Fifo_threshold interrupt source‟s behavior depends on the running mode (Tx, Rx or Stby mode)
and the threshold itself can be programmed via MCParam_Fifo_thresh (B value). This behavior is illustrated in
Figure 32.
IRQ source
1
0
B
B+1 B+2
# of bytes in FIFO
Tx
Rx & Stby
Figure 32: FIFO Threshold IRQ Source Behavior
5.2.2.4. FIFO Clearing
Table 16 below summarizes the status of the FIFO when switching between different modes
Table 16: Status of FIFO when Switching Between Different Modes of the Chip
From
Stby
To
Tx
FIFO Status
Cleared
Not cleared
Cleared
Comments
In Buffered mode, FIFO cannot be written in Stby before Tx
In Packet mode, FIFO can be written in Stby before Tx
Stby
Rx
Rx
Tx
Cleared
Rx
Tx
Stby
Rx
Not cleared
Cleared
In Packet & Buffered modes FIFO can be read in Stby after Rx
Tx
Any
Stby
Sleep
Not cleared
Cleared
Page 39 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.2.3. Sync Word Recognition
5.2.3.1. Overview
Sync word recognition (also called Pattern recognition in previous products) is activated by setting
RXParam_Sync_on. The bit synchronizer must also be activated.
The block behaves like a shift register; it continuously compares the incoming data with its internally programmed
Sync word and asserts the Sync IRQ source on each occasion that a match is detected. This is illustrated in Figure
33.
Rx DATA
Bit N-x =
Sync_value[x]
Bit N-1 =
Bit N =
(NRZ)
Sync_value[1] Sync_value[0]
DCLK
SYNC
Figure 33: Sync Word Recognition
During the comparison of the demodulated data, the first bit received is compared with bit 7 (MSB) of byte at
address 22 and the last bit received is compared with bit 0 (LSB) of the last byte whose address is determined by
the length of the Sync word.
When the programmed Sync word is detected the user can assume that this incoming packet is for the node and
can be processed accordingly.
5.2.3.2. Configuration
•
•
•
Size: Sync word size can be set to 8, 16, 24 or 32 bits via RXParam_Sync_size. In Packet mode this field is
also used for Sync word generation in Tx mode.
Error tolerance: The number of errors tolerated in the Sync word recognition can be set to 0, 1, 2 or 3 via
RXParam_Sync_tol.
Value: The Sync word value is configured in SYNCParam_Sync_value. In Packet mode this field is also used
for Sync word generation in Tx mode.
5.2.4. Packet Handler
The packet handler is the block used in Packet mode. Its functionality is fully described in section 5.5.
5.2.5. Control
The control block configures and controls the full chip‟s behavior according to the settings programmed in the
configuration registers.
Page 40 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.3. Continuous Mode
5.3.1. General Description
As illustrated in Figure 34, in Continuous mode the NRZ data to (from) the (de)modulator is directly accessed by
the uC on the bidirectional DATA pin . The SPI Data, FIFO and packet handler are thus inactive.
RFM63B
Tx/Rx
DATA
IRQ_0
CONTROL
IRQ_1(DCLK)
SPI
Data
Rx
SYNC
NSS_CONFIG
RECOG.
CONFIG
SCK
MOSI
MISO
Datapath
Figure 34: Continuous Mode Conceptual View
5.3.2. Tx Processing
In Tx mode, a synchronous data clock for an external uC is provided on IRQ_1 pin. Its timing with respect to the
data is illustrated in Figure 35. DATA is internally sampled on the rising edge of DCLK so the uC can change logic
state anytime outside the greyed out setup/hold zone.
The use of DCLK is compulsory in FSK and optional in OOK.
Page 41 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.3.3. Rx Processing
If the bit synchronizer is disabled, the raw demodulator output is made directly available on DATA pin and no DCLK
signal is provided.
Conversely, if the bit synchronizer is enabled, synchronous cleaned data and clock are made available respectively
on DATA and IRQ_1 pins. DATA is sampled on the rising edge of DCLK and updated on the falling edge as
illustrated in Figure 36.
DATA (NRZ)
DCLK
Figure 36: Rx Processing in Continuous Mode
Note that in Continuous mode it is always recommended to enable the bit synchronizer to clean the DATA signal
even if the DCLK signal is not used by the uC. (bit synchronizer is automatically enabled in Buffered and Packet
mode).
5.3.4. Interrupt Signals Mapping
The tables below give the description of the interrupts available in Continuous mode.
Rx_stby_irq_0
Rx
00 (d)
01
Sync
RSSI
-
IRQ_0
1x
I
R
Q_1
DCLK
Table 17: Interrupt Mapping in Continuous Rx Mode
Note: In Continuous mode, no interrupt is available in Stby mode
Tx
-
I
R
Q_0
DCLK
IRQ_1
Table 18: Interrupt Mapping in Continuous Tx Mode
Page 42 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.3.5. uC Connections
RFM63B
DATA
IRQ_0
IRQ_1 (DCLK)
uC
NSS_CONFIG
SCK
MOSI
MISO
Figure 37: uC Connections in Continuous Mode
Note that some connections may not be needed depending on the application:
•
IRQ_0: if Sync and RSSI interrupts are not used. In this case, leave floating.
•
IRQ_1: if the chip is never used in Tx FSK mode (DCLK connection is not compulsory in Rx and Tx OOK
modes). In this case, leave floating.
•
MISO: if no read register access is needed. In this case, pull-up to VDD through a 100 kΩ resistor.
In addition, NSS_DATA pin (unused in continuous mode) should be pulled-up to VDD through a 100 kΩ resistor.
Please refer to Table 13 for RFM63B‟s pins configuration
5.3.6. Continuous Mode Example
•
Configure all data processing related registers listed below appropriately. In this example we assume that both
Bit synchronizer and Sync word recognition are on.
Table 19: Relevant Configuration Registers in Continuous Mode (data processing related only)
Description
T
x
Rx
MCParam
IRQParam
Data_mode_x
Rx_stby_irq_0
Sync_on
Sync_size
Sync_tol
X
X
X
X
X
X
X
Defines data operation mode
(
Continuous)
Defines IRQ_0 source in Rx mode
Enables Sync word recognition
Defines Sync word size
Defines the error tolerance on Sync word recognition
Defines Sync word value
RXParam
SYNCParam
Tx Mode:
Sync_value
•
•
•
Go to Tx mode (and wait for Tx to be ready, see Figure 50)
Send all packet‟s bits on DATA pin synchronously with DCLK signal provided on IRQ_1
Go to Sleep mode
Rx Mode:
•
Program Rx interrupts: IRQ_0 mapped to Sync (Rx_stby_irq_0=”00”) and IRQ_1 mapped to DCLK (Bit
synchronizer enabled)
•
•
•
•
Go to Rx mode (note that Rx is not ready immediately, see Figure 49)
Wait for Sync interrupt
Get all packet bits on DATA pin synchronously with DCLK signal provided on IRQ_1
Go to Sleep mode
Page 43 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.4. Buffered Mode
5.4.1. General Description
As illustrated in Figure 38, for Buffered mode operation the NRZ data to (from) the (de)modulator is not directly
accessed by the uC but stored in the FIFO and accessed via the SPI Data interface. This frees the uC for other
tasks between processing data from the RFM63B, furthermore it simplifies software development and reduces uC
performance requirements (speed, reactivity). Note that in this mode the packet handler stays inactive.
An important feature is also the ability to empty the FIFO in Stby mode, ensuring low power consumption and
adding greater software flexibility.
RFM63B
IRQ_0
CONTROL
IRQ_1
SPI
Rx
Tx
Data
SYNC
RECOG.
NSS_CONFIG
CONFIG
FIFO
(+SR)
NSS_DATA
SCK
MOSI
DATA
MISO
Datapath
Figure 38: Buffered Mode Conceptual View
Note that Bit Synchronizer is automatically enabled in Buffered mode. The Sync word recognition must be enabled
(RXParam_Sync_on=1) independently of the FIFO filling method selected (IRQParam_Fifo_fill_method).
5.4.2. Tx Processing
After entering Tx in Buffered mode, the chip expects the uC to write into the FIFO, via the SPI Data interface, all the
data bytes to be transmitted (preamble, Sync word, payload...).
Actual transmission of first byte will start either when the FIFO is not empty (i.e. first byte written by the uC) or when
the FIFO is full depending on bit IRQParam_Tx_start_irq_0.
In Buffered mode the packet length is not limited, i.e. as long as there are bytes inside the FIFO they are sent.
When the last byte is transferred to the SR, /Fifoempty IRQ source is asserted to warn the uC, at that time FIFO
can still be filled with additional bytes if needed.
When the last bit of the last byte has left the SR (i.e. 8 bit periods later), the Tx_done interrupt source is asserted
and the user can exit Tx mode after waiting at least 1 bit period from the last bit processed by modulator.
Page 44 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
If the transmitter is switched off (for example due to entering another chip mode) during transmission it will stop
immediately, even if there is still unsent data.
Figure 39 illustrates Tx processing with a 16 byte FIFO depth and Tx_start_irq_0=0. Please note that in this
example the packet length is equal to FIFO size, but this does not need to be the case, the uC can use the FIFO
interrupts anytime during Tx to manage FIFO contents and write additional bytes.
Start condition
(Cf. Tx_start_irq_0)
Fifofull
/Fifoempty
Tx_done
from
SPI Data
15
b15
b14
b13
b12
b11
b10
b9
FIFO
b8
b7
b6
b5
b4
b3
b2
b1
0
b0
Data Tx
(from SR)
XXX
b0
b1 b2
b3
b4
b5
b6 b7
b8
b9
b10 b11 b12 b13 b14 b15
XXX
Figure 39: Tx processing in Buffered Mode (FIFO size = 16, Tx_start_irq_0=0)
5.4.3. Rx Processing
After entering Rx in Buffered mode, the chip requires the uC to retrieve the received data from the FIFO. The FIFO
will actually start being filled with received bytes either; when a Sync word has been detected (in this case only the
bytes following the Sync word are filled into the FIFO) or when the Fifo_fill bit is asserted by the user - depending
on the state of bit, IRQParam_Fifo_fill_method.
In Buffered mode, the packet length is not limited i.e. as long as Fifo_fill is set, the received bytes are shifted into
the FIFO.
The uC software must therefore manage the transfer of the FIFO contents by interrupt and ensure reception of the
correct number of bytes. (In this mode, even if the remote transmitter has stopped, the demodulator will output
random bits from noise)
When the FIFO is full, Fifofull IRQ source is asserted to alert the uC, that at that time, the FIFO can still be unfilled
without data loss. If the FIFO is not unfilled, once the SR is also full (i.e. 8 bits periods later) Fifo_overrun_clr is
asserted and SR‟s content is lost.
Figure 40 illustrates an Rx processing with a 16 bytes FIFO size and Fifo_fill_method=0. Please note that in the
illustrative example of section 5.4.6, the uC does not retrieve any byte from the FIFO through SPI Data, causing
overrun.
Page 45 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Data Rx
(to SR)
“noisy” data
Sync
Preamble
b0
b1 b2
b3
b4
b5
b6 b7
b8
b9
b10 b11 b12 b13 b14 b15
b16
Start condition
(Cf. Fifo_fill_method)
/Fifoempty
Fifofull
Fifo_overrun_clr
Write_byte
15
b15
b14
b13
b12
b11
b10
b9
FIFO
b8
b7
b6
b5
b4
b3
b2
b1
b0
0
Figure 40: Rx Processing in Buffered Mode (FIFO size=16, Fifo_fill_method=0)
5.4.4. Interrupt Signals Mapping
The tables below describe the interrupts available in Buffered mode.
Rx_stby_irq_x
Rx
Stby
00 (d)
01
10
11
00 (d)
01
-
-
-
Write_byte
/Fifoempty
Sync
IRQ_0
IRQ_1
/Fifoempty
-
-
Fifofull
-
-
Fifofull
RSSI
10
11
Fifo_threshold
Fifo_threshold
Table 20: Interrupt Mapping in Buffered Rx and Stby Modes
T
x
/Fifoempty
IRQ_0
Tx_irq_1=0 (d)
Tx_irq_1=1
Fifofull
IRQ_1
Tx_done
Table 21: Interrupt Mapping in Buffered Tx Mode
Page 46 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.4.5. uC Connections
RFM63B
IRQ_0
IRQ_1
uC
NSS_CONFIG
NSS_DATA
SCK
MOSI
MISO
Figure 41: uC Connections in Buffered Mode
Note that depending upon the application, some uC connections may not be needed:
•
•
•
IRQ_0: if none of the relevant IRQ sources are used. In this case, leave floating.
IRQ_1: if none of the relevant IRQ sources are used. In this case, leave floating.
MISO: if no read register access is needed and the chip is used in Tx mode only. In this case, pull up to VDD
through a 100 kΩ resistor.
In addition, DATA pin (unused in buffered mode) should be pulled-up to VDD through a 100 kΩ resistor.
Please refer to Table 13 for the RFM63B‟s pin configuration.
5.4.6. Buffered Mode Example
•
Configure all data processing related registers listed below appropriately. In this example we assume Sync
word recognition is on and Fifo_fill_method=0.
Descrip
tion
T
x
Rx
Data_mode_x
Fifo_size
Fifo_thresh
Rx_stby_irq_0
Rx_stby_irq_1
Tx_irq_1
X
X
X
X
X
X
X
X
Defines data operation mode
Defines FIFO size
Defines FIFO threshold
Defines IRQ_0 source in Rx & Stby modes
Defines IRQ_1 source in Rx & Stby modes
Defines IRQ_1 source in Tx mode
Defines FIFO filling method
Controls FIFO filling status
Defines Tx start condition and IRQ_0 source
Defines Sync word size
Defines the error tolerance on Sync word detection
Defines Sync word value
( Buffered)
MCParam
IRQParam
X
X
Fifo_fill_method
X
X
F
if
o_
f
ill
Tx_start_irq_0
Sync_size
Sync_tol
X
X
X
RXParam
SYNCParam
Sync_value
Table 22: Relevant Configuration Registers in Buffered Mode (data processing related only)
Tx Mode:
•
Program Tx start condition and IRQs: Start Tx when FIFO is not empty (Tx_start_irq_0=1) and IRQ_1 mapped
to Tx_done (Tx_irq_1=1)
•
Go to Tx mode (and wait for Tx to be ready, see Figure 50)
Page 47 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
•
Write packet bytes into FIFO. Tx starts when the first byte is written (Tx_start_irq_0=1). We assume the FIFO is
being filled via SPI Data faster than being unfilled by SR.
Wait for Tx_done interrupt (+1 bit period)
•
•
Go to Sleep mode
Rx Mode:
•
Program Rx/Stby interrupts: IRQ_0 mapped to /Fifoempty (Rx_stby_irq_0=10) and IRQ_1 mapped to
Fifo_threshold (Rx_stby_irq_1=11). Configure Fifo_thresh to an appropriate value (ex: to detect packet end if
its length is known)
•
•
•
•
•
Go to Rx mode (note that Rx is not ready immediately, Cf section 7.3.1).
Wait for Fifo_threshold interrupt (i.e. Sync word has been detected and FIFO filled up to the defined threshold).
If it is packet end, go to Stby (SR‟s content is lost).
Read packet bytes from FIFO until /Fifoempty goes low (or correct number of bytes is read).
Go to Sleep mode.
Page 48 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.5. Packet Mode
5.5.1. General Description
Similar to Buffered mode operation, in Packet mode the NRZ data to (from) the (de)modulator is not directly
accessed by the uC but stored in the FIFO and accessed via the SPI Data interface.
In addition, the RFM63B‟s packet handler performs several packet oriented tasks such as Preamble and Sync
word generation, CRC calculation/check, whitening/dewhitening of data, address filtering, etc. This simplifies still
further software and reduces uC overhead by performing these repetitive tasks within the RF chip itself.
Another important feature is ability to fill and empty the FIFO in Stby mode, ensuring optimum power consumption
and adding more flexibility for the software.
RFM63B
IRQ_0
CONTROL
IRQ_1
SPI
Rx
Tx
Data
SYNC
RECOG.
NSS_CONFIG
CONFIG
PACKET
HANDLER
FIFO
(+SR)
NSS_DATA
SCK
MOSI
DATA
MISO
Datapath
Figure 42: Packet Mode Conceptual View
Note that Bit Synchronizer and Sync word recognition are automatically enabled in Packet mode.
5.5.2. Packet Format
Two types of packet formats are supported: fixed length and variable length, selectable by the
PKTParam_Pkt_format bit. The maximum size of the payload is limited by the size of the FIFO selected (16, 32, 48
or 64 bytes).
5.5.2.1. Fixed Length Packet Format
In applications where the packet length is fixed in advance, this mode of operation may be of interest to minimize
RF overhead (no length byte field is required). All nodes, whether Tx only, Rx only, or Tx/Rx should be
programmed with the same packet length value.
The length of the payload is set by the PKTParam_Payload_length register and is limited by the size of the FIFO
selected.
Page 49 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
The length stored in this register relates only to the payload which includes the message and the optional address
byte. In this mode, the payload must contain at least one byte, i.e. address or message byte.
An illustration of a fixed length packet is shown in Figure 43. It contains the following fields:
•
•
•
•
•
Preamble (1010...).
Sync word (Network ID).
Optional Address byte (Node ID).
Message data.
Optional 2-bytes CRC checksum.
Optional DC free data coding
CRC checksum calculation
Preamble
1 to 4 bytes
Sync Word
1 to 4 bytes
Address
byte
Message
0 to (FIFO size) bytes
CRC
2-bytes
Payload/FIFO
Fields added by the packet handler in Tx and processed and removed in Rx
Optional User provided fields which are part of the payload
Message part of the payload
Figure 43: Fixed Length Packet Format
5.5.2.2. Variable Length Packet Format
This mode is necessary in applications where the length of the packet is not known in advance and can vary over
time. It is then necessary for the transmitter to send the length information together with each packet in order for
the receiver to operate properly.
In this mode the length of the payload, indicated by the length byte in Figure 44, is given by the first byte of the
FIFO and is limited only by the width of the FIFO selected. Note that the length byte itself is not included in its
calculation. In this mode, the payload must contain at least 2 bytes, i.e. length + address or message byte.
An illustration of a variable length packet is shown in Figure 44. It contains the following fields:
•
•
•
•
•
•
Preamble (1010...).
Sync word (Network ID).
Length byte
Optional Address byte (Node ID).
Message data.
Optional 2-bytes CRC checksum.
Page 50 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Op
CRC checksum calcula
Leng
t
ional DC
f
ree da
t
a coding
t
ion
t
h
Preamble
1 to 4 by es
Sync Word
1 to 4 by es
Leng
by
t
e
h
Address
by
Message
0 to (FIFO size - 1) by
CRC
2-by es
t
es
t
t
t
t
e
t
Payload/FIFO
Fields added by the packet handler in Tx and processed and removed in Rx
Optional User provided fields which are part of the payload
Message part of the payload
Figure 44: Variable Length Packet Format
5.5.3. Tx Processing
In Tx mode the packet handler dynamically builds the packet by performing the following operations on the payload
available in the FIFO:
•
•
•
Add a programmable number of preamble bytes
Add a programmable Sync word
Optionally calculating CRC over complete payload field (optional length byte + optional address byte +
message) and appending the 2 bytes checksum.
•
Optional DC-free encoding of the data (Manchester or whitening).
Only the payload (including optional address and length fields) is to be provided by the user in the FIFO.
Assuming that the chip is already in Tx mode then, depending on IRQParam_Tx_start_irq_0 bit, packet
transmission (starting with programmed preamble) will start either after the first byte is written into the FIFO
(Tx_start_irq_0=1) or after the number of bytes written reaches the user defined threshold (Tx_start_irq_0=0). The
FIFO can also be fully or partially filled in Stby mode via PKTParam_Fifo_stby_access. In this case, the start
condition will only be checked when entering Tx mode.
At the end of the transmission (Tx_done = 1), the user must explicitly exit Tx mode if required. (e.g. back to Stby)
Note that while in Tx mode, before and after actual packet transmission (not enough bytes or Tx_done), additional
preamble bytes are automatically sent to the modulator. When the start condition is met, the current additional
preamble byte is completely sent before the transmission of the next packet (i.e. programmed preamble) is started.
5.5.4. Rx Processing
In Rx mode the packet handler extracts the user payload to the FIFO by performing the following operations:
•
•
•
•
•
Receiving the preamble and stripping it off.
Detecting the Sync word and stripping it off.
Optional DC-free decoding of data.
Optionally checking the address byte.
Optionally checking CRC and reflecting the result on CRC_status bit and CRC_OK IRQ source.
Only the payload (including optional address and length fields) is made available in the FIFO.
Payload_ready and CRC_OK interrupts (the latter only if CRC is enabled) can be generated to indicate the end of
the packet reception.
Page 51 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
By default, if the CRC check is enabled and fails for the current packet, then the FIFO is automatically cleared and
neither of the two interrupts are generated and new packet reception is started. This autoclear function can be
disabled via PKTParam_CRC_autoclr bit and, in this case, even if CRC fails, the FIFO is not cleared and only
Payload_ready IRQ source is asserted.
Once fully received, the payload can also be fully or partially retrieved in Stby mode via
PKTParam_Fifo_stby_access. At the end of the reception, although the FIFO automatically stops being filled, it is
still up to the user to explicitly exit Rx mode if required. (e.g. go to Stby to get payload). FIFO must be empty for a
new packet reception to start.
5.5.5. Packet Filtering
RFM63B‟s packet handler offers several mechanisms for packet filtering ensuring that only useful packets are
made available to the uC, reducing significantly system power consumption and software complexity.
5.5.5.1. Sync Word Based
Sync word filtering/recognition is automatically enabled in Packet mode. It is used for identifying the start of the
payload and also for network identification. As previously described, the Sync word recognition block is configured
(size, error tolerance, value) via RXParam_Sync_size, RXParam_Sync_tol and SYNCParam configuration
registers. This information is used, both for appending Sync word in Tx, and filtering packets in Rx.
Every received packet which does not start with this locally configured Sync word is automatically discarded and no
interrupt is generated.
When the Sync word is detected, payload reception automatically starts and Sync IRQ source is asserted.
5.5.5.2. Address Based
Address filtering can be enabled via the PKTParam_Adrs_filt bits. It adds another level of filtering, above Sync
word, typically useful in a multi-node networks where a network ID is shared between all nodes (Sync word) and
each node has its own ID (address).
Three address based filtering options are available:
•
Adrs_filt = 01: Received address field is compared with internal register Node_Adrs. If they match then the
packet is accepted and processed, otherwise it is discarded.
•
Adrs_filt = 10: Received address field is compared with internal register Node_Adrs and the constant 0x00. If
either is a match, the received packet is accepted and processed, otherwise it is discarded. This additional
check with a constant is useful for implementing broadcast in a multi-node networks.
Adrs_filt = 11: Received address field is compared with internal register Node_Adrs and the constants 0x00 &
0xFF. If any of the three matches, then the received packet is accepted and processed, otherwise it is
discarded. These additional checks with constants are useful for implementing broadcast commands of all
nodes.
•
Please note that the received address byte, as part of the payload, is not stripped off the packet and is made
available in the FIFO. In addition, Node_Adrs and Adrs_filt only apply to Rx. On Tx side, if address filtering is
expected, the address byte should simply be put into the FIFO like any other byte of the payload.
5.5.5.3. Length Based
In variable length Packet mode, PKTParam_Payload_length must be programmed with the maximum length
permitted. If received length byte is smaller than this maximum then the packet is accepted and processed,
otherwise it is discarded.
Page 52 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Please note that the received length byte, as part of the payload, is not stripped off the packet and is made
available in the FIFO.
To disable this function the user should set the value of the PKTParam_Payload_length to the value of the FIFO
size selected.
5.5.5.4. CRC Based
The CRC check is enabled by setting bit PKTParam_CRC_on. It is used for checking the integrity of the message.
•
On Tx side a two byte CRC checksum is calculated on the payload part of the packet and appended to the end
of the message.
•
On Rx side the checksum is calculated on the received payload and compared with the two checksum bytes
received. The result of the comparison is stored in the PKTParam_CRC_status bit and CRC_OK IRQ source.
By default, if the CRC check fails then the FIFO is automatically cleared and no interrupt is generated. This filtering
function can be disabled via PKTParam_CRC_autoclr bit and in this case, even if CRC fails, the FIFO is not
cleared and only Payload_ready interrupt goes high. Please note that in both cases, the two CRC checksum bytes
are stripped off by the packet handler and only the payload is made available in the FIFO.
The CRC is based on the CCITT polynomial as shown in Figure 45. This implementation also detects errors due to
leading and trailing zeros.
CRC Polynomial =X16 + X12 + X5 + 1
data input
X14
X13
X12
X15
X5
X0
X11
X4
* * *
* * *
Figure 45: CRC Implementation
5.5.6. DC-Free Data Mechanisms
The payload to be transmitted may contain long sequences of 1‟s and 0‟s, which introduces a DC bias in the
transmitted signal. The radio signal thus produced has a non uniform power distribution over the occupied channel
bandwidth. It also introduces data dependencies in the normal operation of the demodulator. Thus it is useful if the
transmitted data is random and DC free.
For such purposes, two techniques are made available in the packet handler: Manchester encoding and data
whitening. Please note that only one of the two methods should be enabled at a time.
5.5.6.1. Manchester Encoding
Manchester encoding/decoding is enabled by setting bit PKTParam_Manchester_on and can only be used in
Packet mode.
The NRZ data is converted to Manchester code by coding „1‟ as “10” and „0‟ as “01”.
In this case, the maximum chip rate is the maximum bit rate given in the specifications section and the actual bit
rate is half the chip rate.
Page 53 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Manchester encoding and decoding is only applied to the payload and CRC checksum while preamble and Sync
word are kept NRZ. However, the chip rate from preamble to CRC is the same and defined by MCParam_BR (Chip
Rate = Bit Rate NRZ = 2 x Bit Rate Manchester).
Manchester encoding/decoding is thus made transparent for the user, who still provides/retrieves NRZ data to/from
the FIFO.
1/BR
1/BR
...Syn
c
Payload...
RF chips @ BR
User/NRZ bits
Manchester OFF
User/NRZ bits
Manchester ON
...
1
1
1
0
1
0
0
1
0
0
1
0
1
1
0
1
0
...
t
...
1
1
1
1
0
0
1
0
0
1
0
0
1
0
1
1
0
1
0
...
...
1
1
1
0
0
1
0
0
1
1
...
Figure 46: Manchester Encoding/Decoding
5.5.6.2. Data Whitening
Another technique called whitening or scrambling is widely used for randomizing the user data before radio
transmission. The data is whitened using a random sequence on the Tx side and de-whitened on the Rx side using
the same sequence. Comparing to Manchester technique it has the advantage of keeping NRZ datarate i.e. actual
bit rate is not halved.
The whitening/de-whitening process is enabled by setting bit PKTParam_Whitening_on. A 9-bit LFSR is used to
generate a random sequence. The payload and 2-byte CRC checksum is then XORed with this random sequence
as shown in Figure 47. The data is de-whitened on the receiver side by XORing with the same random sequence.
Payload whitening/de-whitening is thus made transparent for the user, who still provides/retrieves NRZ data to/from
the FIFO.
LFSR Polynom ial =X9 + X5 + 1
X8
X7
X6
X5
X4
X3
X2
X1
X0
W hitened data
Transm it data
Figure 47: Data Whitening
5.5.7. Interrupt Signal Mapping
Tables below give the description of the interrupts available in Packet mode.
Page 54 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Table 23: Interrupt Mapping in Rx and Stby in Packet Mode
Rx
Payload_ready
Write_byte
/Fifoempty
Sync or Adrs_match*
CRC_OK
Stby
Rx_stby_irq_x
00 (d)
01
10
11
00 (d)
01
-
-
I
I
RQ_0
RQ_1
/Fifoempty
-
-
Fifofull
RSSI
Fifofull
-
10
11
Fifo_threshold
Fifo_threshold
*The latter if Address filtering is enabled
T
x
Tx_start_irq_0=0 (d)
Fifo_threshold
/Fifoempty
Fifofull
I
I
RQ_0
RQ_1
Tx_start_irq_0=1
Tx_irq_1=0 (d)
Tx_irq_1=1
Tx_done
Table 24: Interrupt Mapping in Tx Packet Mode
5.5.8. uC Connections
RFM63B
IRQ_0
IRQ_1
uC
NSS_CONFIG
NSS_DATA
SCK
MOSI
MISO
Figure 48: uC Connections in Packet Mode
Note that depending upon the application, some uC connections may not be needed:
•
•
•
IRQ_0: if none of the relevant IRQ sources are used. In this case, leave floating.
IRQ_1: if none of the relevant IRQ sources are used. In this case, leave floating.
MISO: if no read register access is needed and the chip is used in Tx mode only. In this case, pull up to VDD
through a 100 kΩ resistor.
In addition, DATA pin (unused in packet mode) should be pulled-up to VDD through a 100 kΩ resistor.
Please refer to Table 13 for the RFM63B‟s pin configuration.
Page 55 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
5.5.9. Packet Mode Example
•
Configure all data processing related registers listed below appropriately. In this example we assume CRC is
enabled with autoclear on.
Table 25: Relevant Configuration Registers in Packet Mode (data processing related only)
Description
T
x
Rx
Data_mode_x
Fifo_size
Fifo_thresh
Rx_stby_irq_0
Rx_stby_irq_1
Tx_irq_1
X
X
X
X
X
X
X
X
Defines data operation mode
Defines FIFO size
Defines FIFO threshold
Defines IRQ_0 source in Rx & Stby modes
Defines IRQ_1 source in Rx & Stby modes
Defines IRQ_1 source in Tx mode
Defines Tx start condition and IRQ_0 source
Defines Sync word size
( Packet)
MCParam
I
RQParam
X
X
X
Tx_start_irq_0
Sync_size
X
X
X
X
X
X
X
RXParam
Sync_tol
Defines the error tolerance on Sync word detection
Defines Sync word value
SYNCParam
Sync_value
Manchester_on
Payload_length
Node_adrs
X
X
Enables Manchester encoding/decoding
Length in fixed format, max Rx length in variable format
Defines node address for Rx address filtering
Defines packet format (fixed or variable length)
Defines the size of preamble to be transmitted
Enables whitening/de-whitening process
Enables CRC calculation/check
Enables and defines address filtering
Enables FIFO autoclear if CRC failed
Defines FIFO access in Stby mode
X(1)
Pkt_format
X
X
X
X
Preamble_size
Whitening_on
CRC_on
Adrs_filt
CRC_autoclr
Fifo_stby_access
PKTParam
X
X
X
X
X
X
(1)fixed format only
Tx Mode:
•
Program Tx start condition and IRQs: Start Tx when FIFO not empty (Tx_start_irq_0=1) and IRQ_1 mapped to
Tx_done (Tx_irq_1=1)
•
•
•
•
•
Go to Stby mode
Write all payload bytes into FIFO (Fifo_stby_access=0, Stby interrupts can be used if needed)
Go to Tx mode. When Tx is ready (automatically handled) Tx starts (Tx_start_irq_0=1).
Wait for Tx_done interrupt (+1 bit period)
Go to Sleep mode
Rx Mode:
•
Program Rx/Stby interrupts: IRQ_0 mapped to /Fifoempty (Rx_stby_irq_0=10) and IRQ_1 mapped to CRC_OK
(Rx_stby_irq_1=00)
•
•
•
•
•
Go to Rx (note that Rx is not ready immediately, see section 7.3.1
Wait for CRC_OK interrupt
Go to Stby
Read payload bytes from FIFO until /Fifoempty goes low. (Fifo_stby_access =1)
Go to Sleep mode
5.5.10. Additional Information
If the number of bytes filled for transmission is greater than the actual length of the packet to be transmitted and
Tx_start_irq_0 = 1, then the FIFO is cleared after the packet has been transmitted. Thus the extra bytes in the
Page 56 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
FIFO are lost. On the other hand if Tx_start_irq_0 = 0 then the extra bytes are kept into the FIFO. This opens up
the possibility of transmitting more than one packet by filling the FIFO with multiple packet messages.
It is not possible to receive multiple packets. Once a packet has been received and filled into the FIFO all its
content needs to be read i.e. the FIFO must be empty for a new packet reception to be initiated.
The Payload_ready interrupt goes high when the last payload byte is available in the FIFO and remains high until
all its data are read. Similar behavior is applicable to Adrs_match and CRC_OK interrupts.
The CRC result is available in the CRC_status bit as soon as the CRC_successful and Payload_ready interrupt
sources are triggered. In Rx mode, CRC_status is cleared when the complete payload has been read from the
FIFO. If the payload is read in Stby mode, then CRC_status is cleared when the user goes back to Rx mode and a
new Sync word is detected.
The Fifo_fill_method and Fifo_fill bits don‟t have any meaning in the Packet mode and should be set to their default
values only.
Page 57 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
6. Configuration and Status Registers
6.1. General Description
Table 26 sums-up the control and status registers of the RFM63B:
Table 26: Registers List
Name
S
i
ze
Address
Description
MCParam
IRQParam
RXParam
SYNCParam
TXParam
OSCParam
PKTParam
13 x
8
0 - 12
13 - 15
16 - 21
Main parameters common to transmit and receive modes
Interrupt registers
Receiver parameters
Pattern
Transmitter parameters
3 x
6 x
4 x
1 x
1 x
4 x
8
8
8
8
8
8
22
26
27
25
Crystal oscillator parameters
Packet handler parameters
28 - 31
6.2. Main Configuration Register - MCParam
The detailed description of the MCParam register is given in Table 27.
Table 27: MCParam Register Description
A
ddress
Name
B
i
ts
RW
Descrip
tion
(d)
Transceiver mode:
000
001
010
011
100
sleep mode - Sleep
stand-by mode - Stby (d)
frequency synthesizer mode - FS
receive mode - Rx
Chip_mode
7-5
4-3
0
r/w
transmit mode - Tx
Frequency band:
00
01
10
902
915
950
—
—
915 MHz
928 MHz (d)
Freq_band
0
r/w
960 MHz or 863 - 870 MHz (Application Circuit dependant)
Fine VCO trimming:
00
01
10
11
Vtune determined by tank inductors values (d)
VCO_trim
2-1
0
0
0
r/w
r/w
Vtune + 60 mV typ.
Vtune + 120 mV typ.
Vtune + 180 mV typ.
Selection between the two sets of frequency dividers of the PLL, Ri/Pi/Si
0
1
RPS_select
R1/P1/S1 selected(d)
R2/P2/S2 selected
Modulation type:
Modul_select
Data_mode_0
7-6
5
1
1
r/w
r/w
01
10
OOK
FSK (d)
Data operation mode LSB (refer to Data_Mode_1 (Bit 2 Addr 1)
OOK demodulator threshold type:
00
01
10
11
fixed threshold mode
peak mode (d)
average mode
reserved
OOK_thresh_type 4-3
1
r/w
Page 58 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Data operation mode‟s MSB. Cf. Data_mode_0 (Bit 5 Addr 1)
Data_mode_1 Data_mode_0 Data eration
O
p
Bit 2 addr
1
Bit 5 addr
1
Mode
Continuous (d)
Buffered
Data_mode_1
2
1
r/w
0
0
1
0
1
x
Packet
Gain on the IF chain:
00
01
10
11
maximal gain (0dB) (d)
-4.5 dB
-9dB
IF_gain
1-0
7-0
1
2
r/w
r/w
-13.5 dB
Single side frequency deviation in FSK Transmit mode:
Refer to sections 3.3.4 and 3.3.5
f XTAL
Freq_dev
Fdev =
, 0 ≤ D ≤ 255, where D is the value in the register.
32 (D 1)
(d): D = “00000011” => Fdev = 100 kHz
Reserved
(d): “0”
Res
BR
7
3
3
r/w
r/w
f
XTAL
Bit Rate =
, 0 ≤ C ≤ 127, where C is the value in the register.
6-0
64 (C 1)
(d): C = “0000111” => Bit Rate = 25 kb/s NRZ
OOK_
floor_thresh
Floor threshold in OOK Rx mode. By default 6 dB.
(d): “00001100” assuming 0.5 dB RSSI step
7-0
7:6
5-0
4
5
5
r/w
r/w
r/w
FIFO size selection:
00
01
10
11
16 bytes (d)
32 bytes
48 bytes
Fifo_size
64 bytes
FIFO threshold for interrupt source (Cf section 5.2.2.3)
(d): B = “001111”
Fifo_thresh
R counter, active when RPS_select=”0”
(d):77h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode
P counter, active when RPS_select=”0”
(d): 64h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode
S counter, active when RPS_select=”0”
(d): 32h; default values of R1, P1, S1 generate 915.0 MHz in FSK mode
R counter, active when RPS_select=”1”
(d): 74h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode
P counter, active when RPS_select=”1”
(d): 62h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode
S counter, active when RPS_select=”1”
(d): 32h; default values of R2, P2, S2 generate 920.0 MHz in FSK mode
Reserved
(d): “001”
R1
P1
S1
R2
P2
S2
Res
7-0
7-0
7-0
7-0
7-0
7-0
7-5
6
r/w
r/w
r/w
r/w
r/w
r/w
r/w
7
8
9
10
11
12
Ramp control of the rise and fall times of the Tx PA regulator output voltage in
OOK mode:
00
01
10
11
3us
8.5 us
15 us
PA_ramp
Res
4-3
2-0
12
12
r/w
r/w
23 us (d)
Reserved
(d):”000”
Page 59 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
6.3. Interrupt Configuration Parameters - IRQParam
The detailed description of the IRQParam register is given in Table 28.
Table 28: IRQParam Register Description
A
ddress
Name
B
i
ts
RW
Description
(d)
IRQ_0 source in Rx and Standby modes:
If Data_mode(1:0) = 00 (Continuous mode):
00
01
10
11
Sync (d)
RSSI
Sync
Sync
If Data_mode(1:0) = 01 (Buffered mode):
00
01
10
11
- (d)
Rx_stby_irq_0
7-6
13
r/w
Write_byte
/Fifoempty*
Sync
If Data_mode(1:0) = 1x (Packet mode):
00
01
10
11
Payload_ready (d)
Write_byte
/Fifoempty*
Sync or Adrs_match (the latter if address filtering is enabled)
*also available in Standby mode (Cf sections 5.4.4 and 5.5.7)
IRQ_1 source in Rx and Standby modes:
If Data_mode(1:0) = 00 (Continuous mode):
xx
DCLK
If Data_mode(1:0) = 01 (Buffered mode):
00
01
10
11
- (d)
Fifofull*
RSSI
Fifo_threshold*
Rx_stby_irq_1
5-4
13
r/w
If Data_mode(1:0) = 1x (Packet mode):
00
01
10
11
CRC_ok (d)
Fifofull*
RSSI
Fifo_threshold*
*also available in Standby mode (Cf sections 5.4.4 and 5.5.7)
IRQ_1 source in Tx mode:
If Data_mode(1:0) = 00 (Continuous mode):
Tx_irq_1
3
13
r/w
x
DCLK
If Data_mode(1:0) = 01 (Buffered mode) or 1x (Packet mode):
0
1
Fifofull (d)
Tx_done
Fifofull IRQ source
Goes high when FIFO is full.
/Fifoempty IRQ source
Goes low when FIFO is empty
Fifofull
2
1
13
13
r
r
/Fifoempty
r/w/
c
r/w
Goes high when an overrun error occurred. Writing a 1 clears flag and FIFO
Fifo_overrun_clr
Fifo_fill_method
0
7
13
14
FIFO filling method (Buffered mode only):
Page 60 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
0
1
Automatically starts when a sync word is detected (d)
Manually controlled by Fifo_fill
FIFO filling status/control (Buffered mode only):
•
If Fifo_fill_method = „0‟: (d)
Goes high when FIFO is being filled (sync word has been detected)
r/w/
c
Fifo_fill
6
5
14
14
Writing „1‟ clears the bit and waits for a new sync word (if Fifo_overrun_clr=0)
•
0
1
If Fifo_fill_method = „1‟:
Stop filling the FIFO
Start filling the FIFO
Tx_done IRQ source
Goes high when the last bit has left the shift register.
Tx start condition and IRQ_0 source:
Tx_done
r
•
0
1
•
0
If Data_mode(1:0) = 01 (Buffered mode):
Tx starts if FIFO is full, IRQ_0 mapped to /Fifoempty (d)
Tx starts if FIFO is not empty, IRQ_0 mapped to /Fifoempty
If Data_mode(1:0) = 1x (Packet mode):
Tx_start_irq_0
4
14
r/w
Start transmission when the number of bytes in FIFO is greater than or
equal to the threshold set by MCParam_Fifo_thresh parameter (Cf section
5.2.2.3), IRQ_0 mapped to Fifo_threshold (d)
1
Tx starts if FIFO is not empty, IRQ_0 mapped to /Fifoempty
(d): “0”, should be set to “1”.
Res
3
2
14
14
r/w
Note: “0” disables the RSSI IRQ source. It can be left enabled at any time, and
the user can choose to map this interrupt to IRQ0/IRQ1 or not.
RSSI IRQ source:
Goes high when a signal above RSSI_irq_thresh is detected
Writing „1‟ clears the bit
r/w/
c
RSSI_irq
PLL status:
r/w/
c
0
1
not locked
locked
PLL_locked
1
14
Writing a „1‟ clears the bit
PLL_lock detect flag mapped to pin
:
PLL_lock_en
0
14
15
r/w
0
1
Lock detect disabled, pin is High-Z
Lock detect enabled(d)
RSSI threshold for interrupt (coded as RSSI)
(d): “00000000”
RSSI_irq_thresh
7-0
Page 61 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
6.4. Receiver Configuration parameters - RXParam
The detailed description of the RXParam register is given in Table 29.
Table 29: RXParam Register Description
Name
B
i
ts
Address
(d
)
RW Descrip
tion
Typical single sideband bandwidth of the passive low-pass filter.
PassiveFilt = 0000
0001
65 kHz
82 kHz
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
109 kHz
137 kHz
157 kHz
184 kHz
211 kHz
234 kHz
262 kHz
321 kHz
378 kHz (d)
414 kHz
458 kHz
514 kHz
676 kHz
987 kHz
PassiveFilt
7-4
16
r/w
Sets the receiver bandwidth. For BW information please refer to
sections 3.4.5 (FSK) and 3.4.6 (OOK).
ButterFilt
3-0
7-4
16
17
r/w
r/w
(d): “0011” => fC
f0 = 100 kHz
Central frequency of the polyphase filter (100kHz recommended):
PolypFilt_center
(d):“0011” => f0 = 100 kHz
Reserved
Res
3-0
7
17
18
r/w
r/w
(d): “1000”
Enable of the polyphase filter, in OOK Rx mode:
PolypFilt_on
0
1
off (d)
on
Bit synchronizer: control in Continuous Rx mode:
Bitsync_off
Sync_on
6
5
18
18
r/w
r/w
0
1
on (d)
off
Sync word recognition:
0
1
off (d)
on
Sync word size:
00
01
10
11
8 bits
16 bits
24 bits
32 bits (d)
Sync_size
4-3
18
r/w
Number of errors tolerated in the Sync word recognition:
00
01
10
11
0 error (d)
Sync_tol
Res
2-1
0
18
18
r/w
r/w
1
2
3
error
errors
errors
Reserved
(d):”0”
Page 62 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Name
B
i
ts
Address
(d
)
RW Description
Reserved
(d): “00000111”
RSSI output, 0.5 dB / bit
Note: READ-ONLY (not to be written)
Res
7-0
7-0
19
r/w
r
RSSI_val
20
Size of each decrement of the RSSI threshold in the OOK demodulator
000
001
010
011
0.5 dB (d)
1.0 dB
1.5 dB
100
101
110
111
3.0 dB
4.0 dB
5.0 dB
6.0 dB
OOK_thresh_step 7-5
21
r/w
2.0 dB
Period of decrement of the RSSI threshold in the OOK demodulator:
000
001
010
011
100
101
110
111
once in each chip period (d)
once in 2 chip periods
once in 4 chip periods
OOK_thresh_dec
4-2
21
21
r/w
once in 8 chip periods
_period
twice in each chip period
4 times in each chip period
8 times in each chip period
16 times in each chip period
Cutoff frequency of the averaging for the average mode of the OOK
threshold in demodulator
00
01
10
11
OOK_avg_thresh
fC ≈ BR / 8.π (d)
Reserved
Reserved
1-0
r/w
_cutoff
fC ≈ BR / 32.
π
6.5. Sync Word Parameters - SYNCParam
The detailed description of the SYNCParam register is given in Table 30.
Table 30: SYNCParam Register Description
Name
Sync_value(31:24)
B
i
ts
Address
22
(d
)
RW
r/w
Description
7-0
7-0
7-0
7-0
1st Byte of Sync word
(d): “00000000”
Sync_value(23:16)
Sync_value(15:8)
Sync_value(7:0)
23
24
25
2nd Byte of Sync word (only used if Sync_size ≠ 00)
(d): “00000000”
3rd Byte of Sync word (only used if Sync_size = 1x)
(d): “00000000”
4th Byte of Sync word (only used if Sync_size = 11)
(d): “00000000”
Page 63 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
6.6. Transmitter Parameters - TXParam
The detailed description of the TXParam register is given in Table 31.
Table 31: TXParam Register Description
Name
B
i
ts
Address
(d
)
RW
Descrip
tion
InterpFilt
7-4
26
r/w
Tx Interpolation filter cut off frequency:
(d): “0111” => fC = 200 kHz
Pout
3-1
26
r/w
Tx output power (1 step ≈ 3 dB):
000
001
010
011
100
101
110
111
13 dBm
13 dBm -1 step (d)
13 dBm
13 dBm
13 dBm
13 dBm
13 dBm
13 dBm
—
—
—
—
—
2
3
4
5
6
7
steps
steps
steps
steps
steps
steps
Res
0
26
r/w
Reserved
(d): “0”
6.7. Oscillator Parameters - OSCParam
The detailed description of the OSCParam register is given in Table 32.
Table 32: OSCParam Register Description
Name
B
i
ts
Address
RW
Descrip
tion
(d)
Clkout_on
7
27
r/w
Clkout control
0
1
Disabled
Enabled, Clk frequency set by Clkout_freq (d)
Clkout_freq
6-2
1-0
27
r/w
r/w
Frequency of the signal provided on CLKOUT:
(d): 01111 (= 427 kHz)
Reserved
Res
27
(d): “00”
Page 64 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
6.8. Packet Handling Parameters – PKTParam
The detailed description of the PKTParam register is given in Table 33.
Table 33: PKTParam Register Description
Name
B
i
ts
Address
RW
Descrip
tion
(d)
Manchester_on
7
28
r/w
Enable Manchester encoding/decoding:
0
1
off (d)
on
Payload_length
6-0
28
r/w
If Pkt_format=0, payload length.
If Pkt_format=1, max length in Rx, not used in Tx.
(d): “0000000”
Node_adrs
Pkt_format
7-0
7
29
30
r/w
r/w
Node‟s local address for filtering of received packets.
(d): 00h
Packet format:
0
1
fixed length (d)
variable length
Preamble_size
6-5
30
r/w
Size of the preamble to be transmitted:
00
01
10
11
1
2
byte
bytes
3 bytes (d)
bytes
4
Whitening_on
CRC_on
4
30
30
30
r/w
r/w
r/w
Whitening/dewhitening process:
0
1
off (d)
on
3
CRC calculation/check:
0
1
off
on (d)
Adrs_filt
2-1
Address filtering of received packets:
00
01
10
11
off (d)
Node_adrs accepted, else rejected.
Node_adrs & 0x00 accepted, else rejected.
Node_adrs & 0x00 & 0xFF accepted, else rejected.
CRC_status
CRC_autoclr
Fifo_stby_access
Res
0
30
31
31
31
r
CRC check result for current packet (READ ONLY):
0
1
Fail
Pass
7
r/w
r/w
r/w
FIFO auto clear if CRC failed for current packet:
0
1
on (d)
off
6
FIFO access in standby mode:
0
1
Write (d)
Read
5-0
Reserved
(d): “000000”
Page 65 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7. Application Information
7.1. Crystal Resonator Specification
Table 34 shows the crystal resonator specification for the crystal reference oscillator circuit of the RFM63B.
This specification covers the full range of operation of the RFM63B and is employed in the reference design (see
section
7.5.3).
Table 34: Crystal Resonator Specification
Name
Fxtal
Cload
Rm
Descrip
Nominal frequency
Load capacitance for Fxtal
Motional resistance
Shunt capacitance
t
ion
M
in.
9
10
-
T
y
p.
Max
15
16.5
100
7
.
Unit
MHz
pF
ohms
pF
12.800
15
-
-
Co
1
Calibration tolerance at 25+/-3°C
Stability over temperature range [-40°C ; +85°C]
-15
-2
-2
-
+15
+20
ppm
ppm
Fxtal
Fxtal( T)
0
-
Ageing tolerance in first 5 years
-
+2
ppm/year
Fxtal( t)
Note that the initial frequency tolerance, temperature stability and ageing performance should be chosen in
accordance with the target operating temperature range and the receiver bandwidth selected.
7.2. Software for Frequency Calculation
The R1, P1, S1, and R2, P2, S2 dividers are configured over the SPI interface and programmed by 8 bits each, at
addresses 6 to 11. The frequency pairs may hence be switched in a single SPI cycle.
7.2.1. GUI
To aid the user with calculating appropriate R, P and S values, software is available to perform the frequency
calculation. The RFM63B PLL frequency Calculator Software can be downloaded from the Semtech website.
7.2.2. .dll for Automatic Production Bench
The Dynamically Linked Library (DLL) used by the software to perform these calculations is also provided, free of
charge, to users, for inclusion in automatic production testing. Key benefits of this are:
•
No hand trimming of the reference frequency required: the actual reference frequency of the Device Under Test
(DUT) can be easily measured (e.g. from the CLKOUT output of the RFM63B) and the tool will calculate
the best frequencies to compensate for the crystal initial error.
•
Channel plans can be calculated and stored in the application‟s memory, then adapted to the actual crystal
oscillator frequency.
7.3. Switching Times and Procedures
As an ultra-low power device, the RFM63B can be configured for low minimum average power consumption.
To minimize consumption the following optimized transitions between modes are shown.
Page 66 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.3.1. Optimized Receive Cycle
The lowest-power Rx cycle is the following:
RFM63B
I
DD
I
DDR
3.0mA yp
t
.
I
DDFS
1.3mA yp
t
.
I
DDST
65uA
DD
100nA
t
yp
.
I
S
L
t
yp
.
i
Rx
time
RFM63B can be put in
Any other mode
Wait
TS_RE
Receiver is ready
:
-RSSI sampling is valid after a 1/Fdev period
-Received data is valid
Wait
TS_FS
Set RFM63B in Rx mode
Wait for Receiver settling
Wait
TS_OSC
Set RFM63B in FS mode
Wait for PLL settling
Set RFM63B in Standby mode
Wait for XO settling
Figure 49: Optimized Rx Cycle
Note: If the lock detect indicator is available on an external interrupt pin of the companion uC, it can be used to
optimize TS_FS, without having to wait the maximum specified TS_FS.
Page 67 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.3.2. Optimized Transmit Cycle
RFM63B
IDD
IDDT
16mA typ. @1dBm
IDDFS
1.3mA typ.
IDDST
65uA typ.
IDDSL
100nA typ.
Tx
time
RFM63B can be put in
Any other mode
Wait
TS_TR
Data transmission can start in
Continuous and Buffered
modes
Wait
TS_FS
Set RFM63B in Tx mode
Packet mode starts its operation
Wait
TS_OSC
Set RFM63B in FS mode
Wait for PLL settling
Set RFM63B in Standby mode
Wait for XO settling
Figure 50: Optimized Tx Cycle
Note: As stated in the preceding section, TS_FS time can be improved by using the external lock detector pin as
external interrupt trigger.
Page 68 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.3.3. Transmitter Frequency Hop Optimized Cycle
RFM63B
I
DD
I
DDT
16mA typ. @1dBm
I
DDFS
1.3mA yp
t
.
Time
Wait
TS_TR
RFM63B is now
ready for data
transmission
Wait
TS_HOP
Set RFM63B back in Tx mode
1. Set R2/P2/S2
2. Set RFM63B in FS mode, change
MCParam_Band if needed, then switch
from R1/P1/S1 to R2/P2/S2
RFM63B is in Tx mode
On channel 1 (R1 P1 S1)
/
/
Figure 51: Tx Hop Cycle
Page 69 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.3.4. Receiver Frequency Hop Optimized Cycle
RFM63B
I
DD
DDR
3mA yp
I
t
I
DDFS
1.3mA yp
t
.
Time
Wait
TS_RE
RFM63B is now
ready for data
reception
Wait
TS_HOP
Set RFM63B back in Rx mode
1. Set R2/P2/S2
2. Set RFM63B in FS mode, change
MCParam_Band if needed, then switch
from R1/P1/S1 to R2/P2/S2
RFM63B is in Rx mode
On channel 1 (R1 P1 S1)
/
/
Figure 52: Rx Hop Cycle
Note: it is also possible to move from one channel to the other one without having to switch off the receiver. This
method is faster, and overall draws more current. For timing information, please refer to TS_RE_HOP on Table 8.
Page 70 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.3.5. Rx Tx and Tx Rx Jump Cycles
RFM63B
I
DD
I
DDT
16mA typ. @1dBm
I
DDR
3.0mA yp
t
.
Time
Wait
TS_RE
RFM63B is ready to receive data
Set RFM63B in
Rx mode
Wait
TS_TR
RFM63B is now
ready for data
transmission
Set RFM63B in
Tx mode
RFM63B is in
Rx mode
Figure 53: Rx
Tx
Rx Cycle
Page 71 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.4. Reset of the Chip
A power-on reset of the RFM63B is triggered at power up. Additionally, a manual reset can be issued by
controlling pin 13.
7.4.1. POR
If the application requires the disconnection of VDD from the RFM63B, despite of the extremely low Sleep Mode
current, the user should wait for 10 ms from of the end of the POR cycle before commencing communications over
the SPI bus. Pin 13 (TEST8) should be left floating during the POR sequence.
VDD
Pin 13
Undefined
(output)
Wait for Chip is ready from
this point on
10 ms
Figure 54: POR Timing Diagram
Please note that any CLKOUT activity can also be used to detect that the chip is ready.
7.4.2. Manual Reset
A manual reset of the RFM63B is possible even for applications in which VDD cannot be physically disconnected.
Pin 13 should be pulled high for a hundred microseconds, and then released. The user should then wait for 5 ms
before using the chip.
VDD
Wait for
5 ms
Chip is ready from
this point on
> 100 us
Pin 13
(input)
High-Z
‟‟1‟‟
High-Z
Figure 55: Manual Reset Timing Diagram
Please note that while pin 13 is driven high, an over current consumption of up to ten milliamps can be seen on
VDD.
Page 72 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.5. Reference Design
It is recommended that this reference design is replicated in the final application board to guarantee optimum
performance.
7.5.1. Application Schematic
Page 73 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.5.4. SAW Filter Plot
The following screenshot shows the plot of the SAW filter used on the reference design:
0
-10
-20
-30
-40
-50
-60
-70
-80
400
600
800
1000
1200
1400
1600
1800
2000
Frequency [MHz]
Figure 59: 915 MHz SAW Filter Plot
0
-10
-20
-30
-40
-50
-60
-70
-80
400
600
800
1000
1200
1400
1600
1800
2000
Frequency [MHz]
Figure 60: 869 MHz SAW Filter Plot
Page 74 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6. Reference Design Performance
All the measurements visible on section 7.6 typical figures obtained under the following conditions, unless
otherwise noted:
•
•
•
•
•
•
•
•
•
•
Nominal VDD = 3.3 V
Tests performed at room temperature: 25°C +/-3°C
Center frequency 869 MHz or 915 MHz
{R, P, S} triplets are those calculated by the software described in section 3.2.8.
All register settings are default, except for those stated in the relevant sub-sections
Maximum Output Power programmed on Pout tests
All sensitivities are evaluated in Continuous mode, demodulating a PN15 sequence, BER=0.1%
FSK sensitivities measured at 25kbps, Fdev=+/-50 kHz
OOK sensitivities measured at 8kbps, with Fo=100 kHz. IF2 set to 100 kHz.
On all Adjacent Channel Rejection (ACR), Blocking and Spurious Response Frequency tests, the unwanted
signal is unmodulated.
•
•
Bill of Materials as shown in section 7.5.3. In particular, a SAW filter is used (see its performance on section
7.5.4)
The filter settings described on Table 37 and Table 38 were used for the measurements of section 7.6.5.
Table 37: FSK Rx Filters vs. Bit Rate
Bit Rate
Fdev
Filter
Setting
Addr 16
Fdev
+
BR/2
Rx 3 dB BW
Max. drift
Programmed Actual
kbps
100
66.67
50
+/- kHz
200
133
100
80
Hex
FF
E9
D6
B5
A4
A3
A3
72
72
72
72
41
41
41
41
41
41
kHz
250
kHz
400
250
175
150
125
100
100
75
kHz
306
214
158
137
116
96
+/- ppm
62
53
37
41
36
27
37
15
21
26
30
7
166.7
125
40
100
33.33
28.57
25
67
83.3
71.4
62.5
55.6
50
57
50
96
22.22
20
44
69
40
75
69
18.18
16.67
15.38
14.29
12.5
10
36
45.5
41.7
41
75
69
33
75
69
33
50
47
33
40.5
39.6
38.3
35.8
34.3
50
47
7
33
50
47
8
33
50
47
10
12
14
5
33
50
47
2
33
50
47
Table 38: OOK Rx Filters vs. Bit Rate
Bit Rate FO + BR
Filter
Setting
Addr 16
Rx 3 dB BW
Max.
drift
Programmed Actual
kbps
16.67
12.5
9.52
8
kHz
117
113
110
108
105
102
102
Hex
C1
C1
A0
A0
A0
A0
A0
kHz
150
150
125
125
125
125
125
kHz
154
154
129
129
129
129
129
+/- ppm
41
46
22
23
4.76
2.41
1.56
27
30
30
Page 75 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.1. Sensitivity Flatness
Sensitivity over the Frequency Band
-90
.
0
0
0
0
0
0
0
0
0
14
12
10
.
.
.
0
0
0
-92.
-94.
-96.
8
.
0
0
0
0
0
-98
-100
-102
.
6.
.
4.
.
2.
-104.
0.
-106.
-2.0
863
864
865
866
867
868
869
870
Freque ncy [MHz]
Sensitivity
SAW Ripple
Figure 61: Sensitivity Across the 868 MHz Band
Sensitivity over the Frequency Band
-90.0
-92.0
14.0
12.0
10.0
8.0
-94.0
-96.0
-98.0
6.0
-100.0
-102.0
-104.0
-106.0
4.0
2.0
0.0
-2.0
902
904
906
908
910
912
914
916
918
920
922
924
926
928
Frequency [MHz]
Sensitivity
SAW Ripple
Figure 62: Sensitivity Across the 915 MHz Band
Notes:
•
Measured in FSK mode only. OOK sensitivity characteristics will be similar.
•
The sensitivity difference along the band remains inside the ripple performance of the SAW filter (the nominal
passband of the 869 MHz SAW filter is 868
—
870 MHz)
•
The SAW filter ripple response is referenced to its insertion loss at 869 MHz and 915 MHz for each filter.
Page 76 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.2. Sensitivity vs. LO Drift
Sensitivity Loss vs. LO Drift
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-1.0
-25
-20
-15
-10
-5
0
5
10
15
20
25
LO Drift [kHz]
Figure 63: FSK Sensitivity Loss vs. LO Drift
Sensitivity Loss vs. LO Drift
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-1.0
-100
-80
-60
-40
-20
0
20
40
60
80
100
LO Drift [kHz]
Figure 64: OOK Sensitivity Loss vs. LO Drift
Notes:
•
•
•
In FSK Mode, the default filter setting (“A3” at address $16) is kept, leading to Fc=96 kHz typ.
In OOK Mode, “F3” is set at address $16, leading to (Fc-Fo)=95 kHz typ.
The above ensures that the channel filter is wide enough, therefore characterizing the demodulator response,
and NOT the filter response.
Page 77 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.3. Sensitivity vs. Receiver BW
Sensitivity vs. Fc
1.0
0.0
-1.0
-2.0
-3.0
-4.0
-5.0
-6.0
50
100
150
200
250
300
Fc of Active Filter [kHz]
Figure 65: FSK Sensitivity vs. Rx BW
Sensitivity Change vs. (Fc-Fo)
1.0
0.0
0
50
100
150
200
250
300
350
-1.0
-2.0
-3.0
-4.0
-5.0
-6.0
Fc-Fo [kHz]
Figure 66: OOK Sensitivity Change vs. Rx BW
Page 78 of 90
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.4. Sensitivity Stability over Temperature and Voltage
Sensitivity Stability
1.5
1.0
0.5
0.0
2.10
2.40
2.70
3.00
3.30
3.60
85°C
25°C
0°C
-0.5
-40°C
-1.0
-1.5
-2.0
-2.5
VDD [V]
Figure 67: Sensitivity Stability
Note:
•
The sensitivity performance is very stable over the VDD range, and the effect of high temperature is minimal.
7.6.5. Sensitivity vs. Bit Rate
Sensitivity Change over BR
8.0
6.0
4.0
2.0
0.0
0
10
0
25
50
75
-2.0
-4.0
-6.0
-8.0
Bit Rate [kb/s]
Figure 68: FSK Sensitivity vs. BR
Page 80 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Sensitivity Change over the BR
2.0
1.5
1.0
0.5
0.0
1
.5
4
6. 5
9
11.5
1
4
16.5
-0.5
-1.0
-1.5
-2.0
-2.5
Bit Rate [kbps]
Figure 69: OOK Sensitivity vs. BR
7.6.6. Adjacent Channel Rejection
ACR in FSK Mode
70
60
50
40
30
20
10
0
-1000
-800
-600
-400
-200
0
200
400
600
800
1000
Offse t [kHz]
Figure 70: ACR in FSK Mode
Page 81 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
ACR in OOK Mode
60
50
40
30
20
10
0
0
-300
-200
-100
100
200
300
-10
-20
Offse t [kHz]
Figure 71: ACR in OOK Mode
Notes:
•
In FSK mode, the unwanted signal is unmodulated (as described in the EN 300-220 V2.1.1).Co-Channel
Rejection (CCR, Offset = 0kHz) is positive due to the DC cancellation process of the zero-IF architecture
In OOK mode, the polyphase filter efficiency is limited, thus limiting the adjacent channel rejection at 2xFo
distance.
•
7.6.7. Output Power Flatness
Pout Over the Frequency Band
12.0
10.0
8.0
4.0
2.0
0.0
6.0
-2.0
-4.0
-6.0
-8.0
4.0
2.0
0.0
863
864
865
866
867
868
869
870
Fre quency [MHz]
Pout
SAW Ripple
Figure 72: Pout for 869 MHz Band Operation
Page 82 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Pout over the Frequency Band
12.00
10.00
8.00
6.00
4.00
2.00
0.00
4.0
2.0
0.0
-2.0
-4.0
-6.0
-8.0
902
904
906
908
910
912
914
916
918
920
922
924
926
928
Fre que ncy [MHz]
Pout
SAW Ripple
Figure 73: Pout for 915 MHz Band Operation
As noted in section 7.5.4, the 869 MHz SAW filter does not cover the whole European 863
Notes:
•
—
870 MHz
frequency band when used in a 50 ohms environment. Hence the output power degradation at the lowest
frequencies. For applications in the 863
—
870 MHz band it is recommended that an appropriate SAW filter be
implemented or that the SAW response tuned by external matching.
•
The SAW filter ripple references are the insertion loss of each SAW at 869 MHz and 915 MHz.
7.6.8. Pout and IDD vs. PA Setting
Pout & IDD vs. TXParam_Pout Setting
12.0
8.0
28.00
26.00
24.00
22.00
20.00
18.00
16.00
14.00
12.00
10.00
4.0
0.0
-4.0
-8.0
-12.0
0
1
2
3
4
5
6
7
TXPa ram_Pout [d]
Pout IDD
Figure 74: Pout and IDD at all PA Settings, 869 MHz
Page 83 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
Pout & IDD vs. TXParam_Pout Setting
12.0
10.0
8.0
30.0
28.0
26.0
24.0
22.0
20.0
18.0
16.0
14.0
12.0
10.0
6.0
4.0
2.0
0.0
-2.0
-4.0
-6.0
-8.0
-10.0
-12.0
0
1
2
3
4
5
6
7
TXParam_Pout [d]
Pout IDD
Figure 75: Pout and IDD at all PA Settings, 915 MHz
Note:
•
+10dBm typ. Output power is achievable, even at SAW filter‟s output.
7.6.9. Pout Stability over Temperature and Voltage
Pout Stability
1.0
0.5
0.0
.1
2
2 .4
2.7
3.0
3
.3
3 .
6
85°C
-0.5
-1.0
-1.5
-2.0
25°C
-40°C
0°C
VDD [V]
Figure 76: Pout Stability
The output power is not sensitive to the supply voltage, and it decreases slightly when temperature rises.
Page 84 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.10. Transmitter Spectral Purity
Figure 77: 869 MHz Spectral Purity DC-1GHz
Figure 78: 869 MHz Spectral Purity 1-6GHz
Page 85 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.11. OOK Channel Bandwidth
The OOK bit rate ranges form 1.56 to 16.7 kbps. It is interesting to note that, for the lowest bit rates, a channel
spacing approaching 200 kHz is achievable:
Figure 79: OOK Spectrum - 2kbps
Figure 80: OOK Spectrum - 8kbps
Figure 81: OOK Spectrum - 16.7kbps
Notes:
•
The test conditions are: Fdev=100 kHz, TXParam_InterpFilt = 200 kHz
Page 86 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.12. FSK Spectrum in Europe
Figure 82 shows the minimal spectral occupation achievable in the European band, keeping in mind that the
minimum frequency deviation that a RFM63B receiver can accept is 33 kHz. If the companion receiver can bear
smaller frequency deviations, the range of modulation bandwidth can be further decreased.
Figure 82: FSK - 1.56kbps - +/-33 kHz
The default configuration of the RFM63B yields the bandwidth visible on Figure 83:
Figure 83: FSK - 25 kbps - +/-50 kHz
Figure 84 shows the maximal bit rate and frequency deviation that can fit in the 868 to 868.6 MHz European sub-
band:
Figure 84: FSK - 40 kbps - +/-40 kHz
Page 87 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.13. Digital Modulation Schemes
FCC Part 15.247 allows for systems employing digital modulation techniques to transmit up to 1 W, provided that
the 6 dB bandwidth of the signal is at least 500 kHz and that the power spectral density does not exceed 8dBm in
any 3 kHz bandwidth.
The RFM63B can actually meet these constraints whilst transmitting at the maximum output power of the device of
typ. 10dBm, thanks to the built-in whitening process described in section 5.5.6.2:
Figure 85: DTS 6dB Bandwidth
Figure 86: DTS Power Spectral Density
Conditions:
•
•
•
•
Pout = +10.6dBm
Fdev = +/-200kHz
BR=100 kbps (Chip rate=100kCps, as data whitening is enabled)
Packet mode, data whitening enabled
Note: Manchester encoding allows meeting an even lower power spectral density, at the expense of the bit rate
efficiency.
Page 88 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
7.6.14. Current Stability over Temperature and Voltage
Sleep Mode
Curre
nt
Standby Mode
C
urrent
1200
1000
100
90
80
800
600
400
200
0
60
50
40
30
85°C
25°C
0°C
85°C
25°C
0°C
-40°C
-40°C
10
0
2.1
2.4
2.7
3
3.3
3.6
2.1
2.4
2.7
3
3.3
3.6
VDD [V]
VDD [V]
FS Mode
C
urre
nt
Rx Mode
Curre
nt
2.00
1.80
1.60
1.40
1.20
1.00
0.80
0.60
0.40
0.20
0.00
4.00
3.00
2.50
2.00
1.50
1.00
0.50
0.00
85°C
25°C
0°C
85°C
25°C
0°C
-40°C
-40°C
2.1
2.4
2.7
3
3.3
3.6
2.1
2.4
2.7
3
3.3
3.6
VDD [V]
VDD [V]
Tx Mode Current
(Max Output Power)
30.0
25.0
20.0
15.0
10.0
5.0
85°C
25°C
-40°C
0°C
0.0
2.1
2.4
2.7
3.0
3.3
3.6
VDD [V]
Figure 87: IDD vs. Temp and VDD
Page 89 of 92
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
8. Packaging Information
Figure 88: S2 Package Dimensions
Page 90 of 91
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
RFM63B
ADVANCED COMMUNICATIONS & SENSING
9. Ordering Information
Part Number=module type — operation band — package type
RFM63B —868 S2
Package
Mode Type
P/N:RFM63B-868S2
RFM63B module at 868MHz band, SMD Package
P/N:RFM63B-915S2
RFM63B module at 915MHz band, SMD Package
This document may contain preliminary information and is subject to
change by Hope Microelectronics without notice. Hope Microelectronics
assumes no responsibility or liability for any use of the information
contained herein. Nothing in this document shall operate as an express or
implied license or indemnity under the intellectual property rights of Hope
Microelectronics or third parties. The products described in this document
are not intended for use in implantation or other direct life support
applications where malfunction may result in the direct physical harm or
injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MECHANTABILITY
OR FITNESS FOR AARTICULAR PURPOSE, ARE OFFERED IN THIS
DOCUMENT.
HOPE MICROELECTRONICS CO.,LTD
Add: 2/F, Building 3, Pingshan Private
Enterprise Science and Technology
Park, Lishan Road, XiLi Town, Nanshan
District, Shenzhen, Guangdong, China
Tel: 86-755-82973805
Fax: 86-755-82973550
Email: sales@hoperf.com
Website: http://www.hoperf.com
http://www.hoperf.cn
©2006, HOPE MICROELECTRONICS CO.,LTD. All rights reserved.
Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com
相关型号：
©2020 ICPDF网 联系我们和版权申明