BF4MC-6GTXRX-B1-55MM [HRS]
Active Optical Connector;型号: | BF4MC-6GTXRX-B1-55MM |
厂家: | HRS |
描述: | Active Optical Connector |
文件: | 总8页 (文件大小:547K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Active Optical Connector
BF4M Series
Block diagram
Electrical input
Optical Fiber
Electrical output
TIA +
LA
VCSEL
Driver
PD
VCSEL
BF4 transmitter
BF4 receiver
PD: Photo Diode
TIA: Trans mpedance Amplifier
LA: Limiting Amplifier
VCSEL: Vertical Cavity Surface Emitting Laser
Fig.1
Overview
Eye Diagram (Typical) :
Transmission speed 6.25 Gbps, Length 5 meters
Hirose developed the micro "BF4MC connector" that
enables optical transmission of data between boards
that are incorporated in devices.
It converts an electrical signal that is received from a
board by using the semiconductor component built-in
the connector, and transfers the data via optical fiber.
BF4MC connector is a revolutionary design that enables
easy use of electromagnetic noise-free, insulated, long-
distance, high-speed transmission. These are the merits
of the optical transmission, mounted inside devices
achieving dramatic downsizing and lower power
consumption when compared to existing optical products.
It can be used in a wide range of applications, medic
alappliances Measurement equipments, FA system
etc.
Fig.2
Features
1. Optical transmissions achieved by
simplified electrical connections
Optical signal transmission is accomplished with electronic
connectors and has eliminated the need for cleaning the
mating faces of traditional fiber optic connectors.
2. High-speed, signal transmissions with
no EMI noise.
Optical signal transmissions rated up to 6.25 Gbps
are possible.
Since there is no EMI noise to contend with on the
signal lines, system design time is reduced.
Full-scale
3. Highly flexible optical fiber
5cm
Assemblies are made with a highly flexible, optical fiber that
allows for tight bend radiuses when used in small devices.
Fig.3
4. Long-distance, high-speed and high
quality signal transmissions
6. Space-saving and low profile
design with 1.5mm height
By using the BF4M, optical transmissions can be
achieved with small form factor electronic
connectors that save on overall size and valuable
PCB space.
The BM4M design is capable of high speed and
high quality signal transmissions even over long
transmission distances.
5. Low power consumption
Power consumption is significantly reduced compared
to conventional optical transceiver.
In cases where the application will demand a high level of reliability, such as automotive,
please contact a company representative for further information.
1
2016.2e
BF4M Series●Active Optical Connector
Electrical characteristics
Electrical characteristics of BF4MC-TX (transmitter side)
Mni
0.05
2.25
1.0
Nominal
----------
2.5/3.3
----------
----------
----------
Max
6.25
Unit
Gbps
V
Transmission speed (8B/10B)
VDD voltage
3.6
ACTIVATE = H voltage
DIN common voltage
DIN differential voltage
VDD voltage
340
V
150
200
mVp
mVp
1400
Electrical characteristics of BF4MC-RX (receiver side)
Min
0.05
2.25
1.45
160
160
1.0
Nominal
----------
2.5/3.3
1.5
Max
6.25
3.6
Unit
Gbps
V
Remarks
----------
----------
Transmission speed (8B/10B)
VDD voltage
VDD 15 voltage
1.55
330
V
When driving with dual power sources
DOUT common voltage
DOUT differential voltage
SD = H voltage
----------
----------
1.5
mVp
mVp
V
----------
----------
330
1.6
----------
Imon
20.0
----------
----------
uA
For internal inspection
<Pin Assignment>
<Pin Functions>
Descriptions of BF4MC-TX pins
BF4MC-TX Plug
BF4MC-RX Plug
Synbol
VDD
Name
Vsupply
Ground
Type
Details
Power Power Supply DC+2.5 or +3.3V
Fiber
Fiber
GND
Ground
-------
H voltage:Active mode
L voltage:Sleep mode
GND 1
20 GND
19 GND
GND 1
20 GND
19 GND
ACTIVE
Activate
Input
FILT
DIN+
DIN–
NC
Filter
------- Decouping condenser connection contact
GND 2
GND 3
GND 2
Data input +
Data input –
Not Connect
Input
Differential Data Input
Input
GND 3
Imon 4
SD 5
VDD 6
GND 7
DOUT- 8
GND 9
18 GND
17 ACTIVE
18 GND
17 EN
16 NC
15 VDD15
14 GND
13 DOUT+
12 GND
VDD 4
GND 5
FILT 6
GND 7
DIN+ 8
GND 9
------- Not connected in normal operation
16 NC
15 NC
14 GND
13 DIN-
Descriptions of BF4MC-RX pins
12 GND
Synbol
Name
Vsupply
Vdd1.5V
Ground
Type
Details
11 GND
11 GND
GND 10
GND 10
VDD
Power Power for PD(*)
Power Power for Core(*)
VDD15
GND
Ground
-------
Top View
H voltage:Detected
L voltage:Undetected
SD
Signal Detect
Output
DOUT+
DOUT–
Data Output +
Data Output –
Output
Output
Differential Data Output
[Dual supply mode]
Not connected
[Single supply mode]
EN pin must be connect to VDD
EN
Regulator Enable
Input
Mirrored photodiode
current monitor
Not Connect
Imon
NC
Output Not connected(Inspection pin)
------- Not connected in normal operation
(*): For details, see Hirose's technical specification ETAD-K0671.
2
BF4M Series●Active Optical Connector
Product Materials
Plug harnesses
Port
Details
LCP(BF4MC:White)
Phosphor bronze (Au plating)
Phosphor bronze (Ni plating)
GaAs
Housing
Contact
Plate
VCSEL
Transmitter plug(TX)
VCSEL driver
Bonding wire
Sealing resin
Heat shrink tubing
Housing
Si(CMOS)
Au
Epoxy resin
Polyolefin(Black)
LCP(BF4MC:White)
Phosphor bronze (Au plating)
Phosphor bronze (Ni plating)
GaAs
Contact
Plate
PD
TIA/LA
Receiver plug(RX)
Si(CMOS)
Bonding wire
Sealing resin
Heat shrink tubing
Fiber
Au
Epoxy resin
Polyolefin(Black)
Silica glass (GI50/80)
UV curable resin/Thermo plastic resin( 0.5)
Ø
Optical fiber
Coating
Receptacles
Port
Details
Housing
Contact
Shell
LCP(Black)
Phosphor bronze (Au plating)
Phosphor bronze (Au plating)
Transmitter Receptacle(TX)
and
Receiver Receptacle(RX)
Composition of Product Number
Refer to the product number to determine the product specifications.
Plug harness
Receptacle
BF4M C-6G TX RX B1 75MM
-
-
BF4 TX 14 DS 0.5 V
-
-
-
(01)
❶
❷
❸
❹
❺
❻
❶
❷
❸
❹
❺
❻
❼
❶Series
❶Series
❷Identification of Bit rate
❷Identification of the Transmitter and Receiver
ꢀC-6G : 0.05 to 6.25 Gbps
ꢀTX : Transmitter
ꢀRX : Receiver
❸❹Type of plug that attaches to both ends of the
harness
❸Number of Electrical terminal pin
ꢀꢀTX : BF4 Transmitter plug
ꢀ14 pin
ꢀꢀRX : BF4 Receiver plug
❹Identification of Socket shape
❺Type of fiber cable
ꢀSocket(S) of Double line assignment pins(D)
ꢀB1 : diameter Ø0.5, Red
ꢀB2 : diameter Ø0.5, Blue
❺Identification of the electric terminal pitch
ꢀ0.5mm
❻Identification of the length of the fiber cable
❻Identification of the mating method
*Cable length less than 1m ⇒ The end of the product
name·**MM(Millimeter)
ꢀV:Vertical mated to the mounting surface
❼Packing specifications
ꢀNone:500 pcs/reel
ꢀ(01):1000 pcs/reel
ꢀ(02):2000 pcs/reel
ꢀ(10):10 pcs/pack
ꢀ(11):100 pcs/reel
*Cable length 1m or more ⇒ The end of the product
name·**M(Meter)
3
BF4M Series●Active Optical Connector
Connection example of +3.3 V (single power supply mode)
4
BF4M Series●Active Optical Connector
Product Appearance and HRS No.
Plug harness
L
(6)
(6)
9.82
9.82
Identification mark Identification mark
for TX side for RX side
BF4MC harness
Part No.
HRS No.
Fiber
Cable length L
45 mm
50 mm
55 mm
60 mm
65 mm
70 mm
75 mm
80 mm
85 mm
90 mm
95 mm
100 mm
1 m
BF4MC-6GTXRX-B1-45MM
BF4MC-6GTXRX-B1-50MM
BF4MC-6GTXRX-B1-55MM
BF4MC-6GTXRX-B1-60MM
BF4MC-6GTXRX-B1-65MM
BF4MC-6GTXRX-B1-70MM
BF4MC-6GTXRX-B1-75MM
BF4MC-6GTXRX-B1-80MM
BF4MC-6GTXRX-B1-85MM
BF4MC-6GTXRX-B1-90MM
BF4MC-6GTXRX-B1-95MM
BF4MC-6GTXRX-B1-100MM
BF4MC-6GTXRX-B1-1M
BF4MC-6GTXRX-B1-2M
BF4MC-6GTXRX-B1-3M
BF4MC-6GTXRX-B1-4M
BF4MC-6GTXRX-B1-5M
831-1102-0 04
831-1102-0 05
831-1102-0 06
831-1102-0 07
831-1102-0 08
831-1102-0 09
831-1102-0 00
831-1102-0 11
831-1102-0 12
831-1102-0 13
831-1102-0 14
831-1102-0 15
831-1109-9 00
831-1109-9 01
831-1109-9 02
831-1109-9 03
831-1109-9 04
Ø0.5 Red
2 m
3 m
4 m
5 m
Length (L) of the harness
· The shortest harness length is 45mm, and the harness up to 100mm in length is available in 5mm increments.
(45mm, 50mm, 55mm …, 100mm)
· Harness longer than those listed above is also available upon request. Please inform us of your desired harness length.
· Blue Fiber color is also available. Contact your sales representative for details.
5
BF4M Series●Active Optical Connector
Receptacle:Transmitter (TX)
10.25
9.5
3
P=0.5 0.05
(2.05)
Vacuum
3mm
pick up area
Vacuum
pick up area
2.1mm
(0.25)
(1.75)
· The structure is designed so that the receiver (RX)
plug does not mate.
Part No.
HRS No.
Package specifications
500 pcs/reel
BF4-TX-14DS-0.5V
831-0008-6 00
831-0008-6 01
831-0008-6 02
831-0008-6 10
831-0008-6 11
BF4-TX-14DS-0.5V(01)
BF4-TX-14DS-0.5V(02)
BF4-TX-14DS-0.5V(10)
BF4-TX-14DS-0.5V(11)
1000 pcs/reel
2000 pcs/reel
10 pcs/pack
100 pcs/reel
Receptacle: Receiver (RX)
10.25
9.5
3
P=0.5 0.05
(1.75)
Vacuum
3mm
pick up area
Vacuum
pick up area
2.1mm
(0.25)
(2.05)
· The structure is designed so that the transmitter (TX)
plug does not mate.
Part No.
HRS No.
Package specifications
500 pcs/reel
BF4-RX-14DS-0.5V
831-0009-9 00
831-0009-9 01
831-0009-9 02
831-0009-9 10
831-0009-9 11
BF4-RX-14DS-0.5V(01)
BF4-RX-14DS-0.5V(02)
BF4-RX-14DS-0.5V(10)
BF4-RX-14DS-0.5V(11)
1000 pcs/reel
2000 pcs/reel
10 pcs/pack
100 pcs/reel
Receptacle:Pattern Layout
Recommended PCB land pattern dimensions
Recommended stencil dimensions
(Stencil thickness 120 μm)
5.6
4.5
5.7
3.8
0.3
P=0.5
3
1.4
0.26
P=0.5
3
1.4
The hatched areas in Figure 2.4(A) are close to metal
0.9 shell, and there is a possibility of a short circuit. Make
sure not to locate a via Hole without a solder mask.
Apeture ratio
Pads for contacts: 70%
Pads for shell: 100%
1
0.9
1
1.2
3.65
1.2
3.65
(
)
4.9
4.9
6
BF4M Series●Active Optical Connector
Packaging Specifications for the receptacles
Reel dimensions
Emboss carrier tape dimensions
t=0.3 0.05
29.5
1
A
2
0.5
25.5 0.5
Ø1.5 sprocket hole
near side
1.6 0.1
2
0.1
P=4 0.1
A-A
P=12 0.1
A
Recommended reflow temperature profile (lead-free solder)
Recommended reflow temperature profile (lead-free solder)
MAX 250℃
Reflow cycle : 2 cycle Max.
250
220ç
220
180ç
180
150
150ç
100
25
Time(sec)
0
Preheat time
Soldering time
(60sec) 90to120sec
60sec MAX.
Extraction tool
(6)
(4.4)
Part No.
BF4-T2
HRS No.
831-0006-0 00
Packing specifications
1 piece
(2.6)
Test board
PCBs for testing and evaluation are available
from Hirose in order to verify the operating
characteristics of plug harnesses.
Please contact us for more information.
BF4M High Speed
Transmission Board : TX2
BF4M High Speed
Transmission Board : RX2
Connector Mating Method
Metal plate (silver) shall be
always on bottom surface
during mating process.
Metal exposed area (gold,
triangle) shall always be
o n t o p s u r f a c e d u r i n g
mating process.
Do not mate the connector while power is being supplied
Make sure to insert or remove the plug after the power
supply is stopped. Hot plugging/unplugging may cause
damage.
7
BF4M Series●Active Optical Connector
Cautions
Do not pull the fiber when removing the connector.
When removing the connector, make sure to hook the plug with an extraction tool so that the stress is not
applied to the cable. Pulling the cable to remove it may cause a breakage in the cable
Unmating tool
Do not remove the plug while power is being supplied.
Make sure to remove the plug after the power supply is
stopped. Hot plugging / unplugging may cause damage.
Notes on handling of the product
(Notes on change of information)
(
Prohibition of weapons of mass destruction and military purposes)
• The content of this document including the information
regarding the connector (hereafter, the Product) is subject to
change without prior notice.
• It is prohibited to use the Product or the technical information
contained in this document for any military purposes, including
but not limited to, development of weapons of mass
destruction.
(Prohibition of reproduction)
• No part of this document may be copied or reproduced without
prior written consent of Hirose Electric Co., Ltd. (hereafter,
Hirose). Even if written consent of Hirose is obtained, it is
prohibited to amend any part of this document and copy or
reproduce it. Hirose shall assume no obligation or liability in
connection with such amended information or reproduction.
(Responsibilities for design safety)
(Notes on export)
• To export the Product to other countries, the exporter shall
conduct the applicability determination based on Foreign
Exchange and Foreign Trade Act of Japan. If you wish to have
the applicability determination sheet issued by Hirose, contact
our sales representative. Note that in the export arrangement,
the customer shall be an exporter and responsible for
compliance with all the applicable laws and regulations and
terms and conditions of the agreement with Hirose.
• Hirose shall assume no responsibilities for the support for the
application of the Product or the product design of the
customer. The customer shall be responsible for the product
and application of the customer in which the Product is used.
The customer shall take appropriate design and operational
safety measures in order to minimize the potential risks
predicted for the product and application of the customer in
which the Product is used.
Notes on use of the product
(Notes on the specification range)
• Using the Product under conditions beyond the specification range
(for voltage, current and temperature) provided in this document
may result in an accident (including ignition, heat generation, and
smoking). Confirm the document thoroughly and make sure to use
the Product within the specification range.
(Responsibilities for determination of the suitability)
• When using the Product, the customer shall ensure safe design
at his/her own responsibility so that malfunction or failure of the
Product would never cause an infringement on the life, body or
property. For design or use of the Product, make sure to refer
to the materials (including the catalog, specifications, and
design note) and follow the same. When using information
including the product data provided in the document, technical
data or circuit examples shown in the figures and tables, the
customer shall evaluate the information on the customer’s
product and determine the suitability at the customer’s own
responsibility.
(Notes on the laser)
• The laser beam is emitted from the end-face of the optical fiber in
operation. It may cause eye injury or loss of sight if it enters the
eyes. Do not stare directly into the end-face of the optical fiber.
The laser beam is emitted from the VCSEL in operation. It may
not be visible depending on its wavelength, but nonetheless it
may cause eye injury or loss of sight if the laser beam or its
reflected beam enters the eyes. Do not stare (look into) the
laser beam directly.
(Responsibilities for specific applications)
• Make sure to consult with our sales representative in advance
when considering of use for specific applications that require
extremely high quality and reliability (e.g. nuclear equipment,
aerospace systems, transportation equipment and various
safety related equipment).
(Notes on fracture of the optical fiber)
• In case of fracture of the optical fiber used in the Product, turn
off the power immediately.
In addition, Use care when handling it to avoid injury from
fractured parts or fragments.
(Prohibition of replication)
• Do not disassemble reverse-engineer, modify, analyze or
replicate the Product.
(Prohibition of application to prohibited products)
• The Product must not be used for any product that
manufacture, use and sale of which is prohibited by the
domestic or international laws, regulations and ordinances.
(Notes on the guarantee and license)
(Notes on use of GaAs)
• The Product is equipped with a semiconductor within the
connector and contains gallium arsenide (GaAs).
(Notes on the environment including gases)
• Avoid the use of the Product in gas environments with chlorides
or sulfides. The Product may deteriorate and features may be
affected.
(Notes on storage)
• The technical data provided in the materials of the Product is
intended to describe the representative behaviors and
application of the Product. It is not to guarantee the intellectual
property rights or any other rights of Hirose nor a third party
and not to grant the license.
• Store the Product out of corrosive substances, corrosive gases,
high temperature and humidity or direct sunlight.
Do not apply excessive pressure or vibration to the Product. It
may cause deterioration, deformation, damage or failure of the
Product.
(Notes on the warranties for the contract)
(Notes on resin molded part)
• Unless otherwise provided in a written contract or other
documents (specifications) agreed between the customer and
Hirose, Hirose makes no warranties of any kind (including, but not
limited to, warranties of the function and operation, warranties of
merchantability, warranties of suitability for a specific application or
purpose and warranties of correctness of the information).
• The resin molded part of the Product may contain black spots
or its color may be slightly different, but that has no effect on
the product performance.
®
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
+
+
TEL: 81-45-620-3526 Fax: 81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 02/2016. Contents are subject to change without notice for the purpose of improvements.
8
相关型号:
©2020 ICPDF网 联系我们和版权申明