BF4MC-6GTXRX-B1-5M [HRS]

Active Optical Connector;


型号：	BF4MC-6GTXRX-B1-5M
厂家：	HRS
描述：	Active Optical Connector
文件：	总8页 (文件大小：547K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Active Optical Connector

BF4M Series

Block diagram

Electrical input

Optical Fiber

Electrical output

TIA +

VCSEL

Driver

VCSEL

BF4 transmitter

BF4 receiver

PD: Photo Diode

TIA: Trans mpedance Amplifier

LA: Limiting Amplifier

VCSEL: Vertical Cavity Surface Emitting Laser

Fig.1

Overview

Eye Diagram (Typical) :

Transmission speed 6.25 Gbps, Length 5 meters

Hirose developed the micro "BF4MC connector" that

enables optical transmission of data between boards

that are incorporated in devices.

It converts an electrical signal that is received from a

board by using the semiconductor component built-in

the connector, and transfers the data via optical fiber.

BF4MC connector is a revolutionary design that enables

easy use of electromagnetic noise-free, insulated, long-

distance, high-speed transmission. These are the merits

of the optical transmission, mounted inside devices

achieving dramatic downsizing and lower power

consumption when compared to existing optical products.

It can be used in a wide range of applications, medic

alappliances Measurement equipments, FA system

etc.

Fig.2

Features

1. Optical transmissions achieved by

simplified electrical connections

Optical signal transmission is accomplished with electronic

connectors and has eliminated the need for cleaning the

mating faces of traditional fiber optic connectors.

2. High-speed, signal transmissions with

no EMI noise.

Optical signal transmissions rated up to 6.25 Gbps

are possible.

Since there is no EMI noise to contend with on the

signal lines, system design time is reduced.

Full-scale

3. Highly flexible optical fiber

5cm

Assemblies are made with a highly flexible, optical fiber that

allows for tight bend radiuses when used in small devices.

Fig.3

4. Long-distance, high-speed and high

quality signal transmissions

6. Space-saving and low profile

design with 1.5mm height

By using the BF4M, optical transmissions can be

achieved with small form factor electronic

connectors that save on overall size and valuable

PCB space.

The BM4M design is capable of high speed and

high quality signal transmissions even over long

transmission distances.

5. Low power consumption

Power consumption is significantly reduced compared

to conventional optical transceiver.

In cases where the application will demand a high level of reliability, such as automotive,

please contact a company representative for further information.

2016.2e

BF4M Series●Active Optical Connector

Electrical characteristics

Electrical characteristics of BF4MC-TX (transmitter side)

Mｎi

0.05

2.25

1.0

Nominal

----------

2.5/3.3

----------

Max

6.25

Unit

Gbps

Transmission speed (8B/10B)

VDD voltage

3.6

ACTIVATE = H voltage

DIN common voltage

DIN differential voltage

VDD voltage

340

150

200

mVp

1400

Electrical characteristics of BF4MC-RX (receiver side)

Miｎ

0.05

2.25

1.45

160

1.0

Nominal

----------

2.5/3.3

1.5

Max

6.25

3.6

Unit

Gbps

Remarks

----------

Transmission speed (8B/10B)

VDD voltage

VDD 15 voltage

1.55

330

When driving with dual power sources

DOUT common voltage

DOUT differential voltage

SD = H voltage

----------

1.5

mVp

----------

330

1.6

----------

Imon

20.0

----------

For internal inspection

Descriptions of BF4MC-TX pins

BF4MC-TX Plug

BF4MC-RX Plug

Synbol

VDD

Name

Vsupply

Ground

Type

Details

Power Power Supply DC+2.5 or +3.3V

Fiber

GND

Ground

-------

H voltage:Active mode

L voltage:Sleep mode

GND 1

20 GND

19 GND

GND 1

20 GND

19 GND

ACTIVE

Activate

Input

FILT

DIN+

DIN–

Filter

------- Decouping condenser connection contact

GND 2

GND 3

GND 2

Data input +

Data input –

Not Connect

Input

Differential Data Input

Input

GND 3

Imon 4

SD 5

VDD 6

GND 7

DOUT- 8

GND 9

18 GND

17 ACTIVE

18 GND

17 EN

16 NC

15 VDD15

14 GND

13 DOUT+

12 GND

VDD 4

GND 5

FILT 6

GND 7

DIN+ 8

GND 9

------- Not connected in normal operation

16 NC

15 NC

14 GND

13 DIN-

Descriptions of BF4MC-RX pins

12 GND

Synbol

Name

Vsupply

Vdd1.5V

Ground

Type

Details

11 GND

GND 10

VDD

Power Power for PD(*)

Power Power for Core(*)

VDD15

GND

Ground

-------

Top View

H voltage:Detected

L voltage:Undetected

Signal Detect

Output

DOUT+

DOUT–

Data Output +

Data Output –

Output

Differential Data Output

[Dual supply mode]

Not connected

[Single supply mode]

EN pin must be connect to VDD

Regulator Enable

Input

Mirrored photodiode

current monitor

Not Connect

Imon

Output Not connected(Inspection pin)

------- Not connected in normal operation

(*): For details, see Hirose's technical speciﬁcation ETAD-K0671.

BF4M Series●Active Optical Connector

Product Materials

Plug harnesses

Port

Details

LCP(BF4MC：White)

Phosphor bronze (Au plating)

Phosphor bronze (Ni plating)

GaAs

Housing

Contact

Plate

VCSEL

Transmitter plug(TX)

VCSEL driver

Bonding wire

Sealing resin

Heat shrink tubing

Housing

Si(CMOS)

Epoxy resin

Polyoleﬁn(Black)

LCP(BF4MC：White)

Phosphor bronze (Au plating)

Phosphor bronze (Ni plating)

GaAs

Contact

Plate

TIA/LA

Receiver plug(RX)

Si(CMOS)

Bonding wire

Sealing resin

Heat shrink tubing

Fiber

Epoxy resin

Polyoleﬁn(Black)

Silica glass (GI50/80)

UV curable resin/Thermo plastic resin( 0.5)

Optical ﬁber

Coating

Receptacles

Port

Details

Housing

Contact

Shell

LCP(Black)

Phosphor bronze (Au plating)

Transmitter Receptacle(TX)

and

Receiver Receptacle(RX)

Composition of Product Number

Refer to the product number to determine the product speciﬁcations.

Plug harness

Receptacle

BF4M C-6G TX RX B1 75MM

BF4 TX 14 DS 0.5 V

(01)

❶

❷

❸

❹

❺

❻

❶

❷

❸

❹

❺

❻

❼

❶Series

❷Identification of Bit rate

❷Identification of the Transmitter and Receiver

ꢀC-6G : 0.05 to 6.25 Gbps

ꢀTX : Transmitter

ꢀRX : Receiver

❸❹Type of plug that attaches to both ends of the

harness

❸Number of Electrical terminal pin

ꢀꢀTX : BF4 Transmitter plug

ꢀ14 pin

ꢀꢀRX : BF4 Receiver plug

❹Identification of Socket shape

❺Type of fiber cable

ꢀSocket(S) of Double line assignment pins(D)

ꢀB1 : diameter Ø0.5, Red

ꢀB2 : diameter Ø0.5, Blue

❺Identification of the electric terminal pitch

ꢀ0.5mm

❻Identification of the length of the fiber cable

❻Identification of the mating method

*Cable length less than 1m ⇒ The end of the product

name·**MM(Millimeter)

ꢀV：Vertical mated to the mounting surface

❼Packing specifications

ꢀNone：500 pcs/reel

ꢀ(01)：1000 pcs/reel

ꢀ(02)：2000 pcs/reel

ꢀ(10)：10 pcs/pack

ꢀ(11)：100 pcs/reel

*Cable length 1m or more ⇒ The end of the product

name·**M(Meter)

BF4M Series●Active Optical Connector

Connection example of +3.3 V (single power supply mode)

BF4M Series●Active Optical Connector

Product Appearance and HRS No.

Plug harness

（6）

9.82

Identification mark Identification mark

for TX side for RX side

BF4MC harness

Part No.

HRS No.

Fiber

Cable length L

45 mm

50 mm

55 mm

60 mm

65 mm

70 mm

75 mm

80 mm

85 mm

90 mm

95 mm

100 mm

1 m

BF4MC-6GTXRX-B1-45MM

BF4MC-6GTXRX-B1-50MM

BF4MC-6GTXRX-B1-55MM

BF4MC-6GTXRX-B1-60MM

BF4MC-6GTXRX-B1-65MM

BF4MC-6GTXRX-B1-70MM

BF4MC-6GTXRX-B1-75MM

BF4MC-6GTXRX-B1-80MM

BF4MC-6GTXRX-B1-85MM

BF4MC-6GTXRX-B1-90MM

BF4MC-6GTXRX-B1-95MM

BF4MC-6GTXRX-B1-100MM

BF4MC-6GTXRX-B1-1M

BF4MC-6GTXRX-B1-2M

BF4MC-6GTXRX-B1-3M

BF4MC-6GTXRX-B1-4M

BF4MC-6GTXRX-B1-5M

831-1102-0 04

831-1102-0 05

831-1102-0 06

831-1102-0 07

831-1102-0 08

831-1102-0 09

831-1102-0 00

831-1102-0 11

831-1102-0 12

831-1102-0 13

831-1102-0 14

831-1102-0 15

831-1109-9 00

831-1109-9 01

831-1109-9 02

831-1109-9 03

831-1109-9 04

Ø0.5 Red

2 m

3 m

4 m

5 m

Length (L) of the harness

· The shortest harness length is 45mm, and the harness up to 100mm in length is available in 5mm increments.

(45mm, 50mm, 55mm …, 100mm)

· Harness longer than those listed above is also available upon request. Please inform us of your desired harness length.

· Blue Fiber color is also available. Contact your sales representative for details.

BF4M Series●Active Optical Connector

Receptacle:Transmitter (TX)

10.25

9.5

P=0.5 0.05

(2.05)

Vacuum

3mm

pick up area

Vacuum

pick up area

2.1mm

(0.25)

(1.75)

· The structure is designed so that the receiver (RX)

plug does not mate.

Part No.

HRS No.

Package speciﬁcations

500 pcs/reel

BF4-TX-14DS-0.5V

831-0008-6 00

831-0008-6 01

831-0008-6 02

831-0008-6 10

831-0008-6 11

BF4-TX-14DS-0.5V(01)

BF4-TX-14DS-0.5V(02)

BF4-TX-14DS-0.5V(10)

BF4-TX-14DS-0.5V(11)

1000 pcs/reel

2000 pcs/reel

10 pcs/pack

100 pcs/reel

Receptacle: Receiver (RX)

10.25

9.5

P=0.5 0.05

(1.75)

Vacuum

3mm

pick up area

Vacuum

pick up area

2.1mm

(0.25)

(2.05)

· The structure is designed so that the transmitter (TX)

plug does not mate.

Part No.

HRS No.

Package speciﬁcations

500 pcs/reel

BF4-RX-14DS-0.5V

831-0009-9 00

831-0009-9 01

831-0009-9 02

831-0009-9 10

831-0009-9 11

BF4-RX-14DS-0.5V(01)

BF4-RX-14DS-0.5V(02)

BF4-RX-14DS-0.5V(10)

BF4-RX-14DS-0.5V(11)

1000 pcs/reel

2000 pcs/reel

10 pcs/pack

100 pcs/reel

Receptacle:Pattern Layout

Recommended PCB land pattern dimensions

Recommended stencil dimensions

(Stencil thickness 120 μm)

5.6

4.5

5.7

3.8

0.3

P=0.5

1.4

0.26

P=0.5

1.4

The hatched areas in Figure 2.4(A) are close to metal

0.9 ^{shell, and there is a possibility of a short circuit. Make}

sure not to locate a via Hole without a solder mask.

Apeture ratio

Pads for contacts: 70%

Pads for shell: 100%

0.9

1.2

3.65

1.2

3.65

（

）

4.9

BF4M Series●Active Optical Connector

Packaging Specifications for the receptacles

Reel dimensions

Emboss carrier tape dimensions

t=0.3 0.05

29.5

0.5

25.5 0.5

Ø1.5 sprocket hole

near side

1.6 0.1

0.1

P=4 0.1

A-A

P=12 0.1

Recommended reﬂow temperature proﬁle (lead-free solder)

Recommended reflow temperature profile (lead-free solder)

MAX 250℃

Reflow cycle : 2 cycle Max.

250

220ç

220

180ç

180

150

150ç

100

Time(sec)

Preheat time

Soldering time

(６０sec) ９０to１２０sec

６０sec MAX.

Extraction tool

（6）

（4.4）

Part No.

BF4-T2

HRS No.

831-0006-0 00

Packing specifications

1 piece

（2.6）

Test board

PCBs for testing and evaluation are available

from Hirose in order to verify the operating

characteristics of plug harnesses.

Please contact us for more information.

BF4M High Speed

Transmission Board : TX2

BF4M High Speed

Transmission Board : RX2

Connector Mating Method

Metal plate (silver) shall be

always on bottom surface

during mating process.

Metal exposed area (gold,

triangle) shall always be

o n t o p s u r f a c e d u r i n g

mating process.

Do not mate the connector while power is being supplied

Make sure to insert or remove the plug after the power

supply is stopped. Hot plugging/unplugging may cause

damage.

BF4M Series●Active Optical Connector

Cautions

Do not pull the fiber when removing the connector.

When removing the connector, make sure to hook the plug with an extraction tool so that the stress is not

applied to the cable. Pulling the cable to remove it may cause a breakage in the cable

Unmating tool

Do not remove the plug while power is being supplied.

Make sure to remove the plug after the power supply is

stopped. Hot plugging / unplugging may cause damage.

Notes on handling of the product

(Notes on change of information)

(

Prohibition of weapons of mass destruction and military purposes)

• The content of this document including the information

regarding the connector (hereafter, the Product) is subject to

change without prior notice.

• It is prohibited to use the Product or the technical information

contained in this document for any military purposes, including

but not limited to, development of weapons of mass

destruction.

(Prohibition of reproduction)

• No part of this document may be copied or reproduced without

prior written consent of Hirose Electric Co., Ltd. (hereafter,

Hirose). Even if written consent of Hirose is obtained, it is

prohibited to amend any part of this document and copy or

reproduce it. Hirose shall assume no obligation or liability in

connection with such amended information or reproduction.

(Responsibilities for design safety)

(Notes on export)

• To export the Product to other countries, the exporter shall

conduct the applicability determination based on Foreign

Exchange and Foreign Trade Act of Japan. If you wish to have

the applicability determination sheet issued by Hirose, contact

our sales representative. Note that in the export arrangement,

the customer shall be an exporter and responsible for

compliance with all the applicable laws and regulations and

terms and conditions of the agreement with Hirose.

• Hirose shall assume no responsibilities for the support for the

application of the Product or the product design of the

customer. The customer shall be responsible for the product

and application of the customer in which the Product is used.

The customer shall take appropriate design and operational

safety measures in order to minimize the potential risks

predicted for the product and application of the customer in

which the Product is used.

Notes on use of the product

(Notes on the specification range)

• Using the Product under conditions beyond the specification range

(for voltage, current and temperature) provided in this document

may result in an accident (including ignition, heat generation, and

smoking). Confirm the document thoroughly and make sure to use

the Product within the specification range.

(Responsibilities for determination of the suitability)

• When using the Product, the customer shall ensure safe design

at his/her own responsibility so that malfunction or failure of the

Product would never cause an infringement on the life, body or

property. For design or use of the Product, make sure to refer

to the materials (including the catalog, specifications, and

design note) and follow the same. When using information

including the product data provided in the document, technical

data or circuit examples shown in the figures and tables, the

customer shall evaluate the information on the customer’s

product and determine the suitability at the customer’s own

responsibility.

(Notes on the laser)

• The laser beam is emitted from the end-face of the optical fiber in

operation. It may cause eye injury or loss of sight if it enters the

eyes. Do not stare directly into the end-face of the optical fiber.

The laser beam is emitted from the VCSEL in operation. It may

not be visible depending on its wavelength, but nonetheless it

may cause eye injury or loss of sight if the laser beam or its

reflected beam enters the eyes. Do not stare (look into) the

laser beam directly.

(Responsibilities for specific applications)

• Make sure to consult with our sales representative in advance

when considering of use for specific applications that require

extremely high quality and reliability (e.g. nuclear equipment,

aerospace systems, transportation equipment and various

safety related equipment).

(Notes on fracture of the optical fiber)

• In case of fracture of the optical fiber used in the Product, turn

off the power immediately.

In addition, Use care when handling it to avoid injury from

fractured parts or fragments.

(Prohibition of replication)

• Do not disassemble reverse-engineer, modify, analyze or

replicate the Product.

(Prohibition of application to prohibited products)

• The Product must not be used for any product that

manufacture, use and sale of which is prohibited by the

domestic or international laws, regulations and ordinances.

(Notes on the guarantee and license)

(Notes on use of GaAs)

• The Product is equipped with a semiconductor within the

connector and contains gallium arsenide (GaAs).

(Notes on the environment including gases)

• Avoid the use of the Product in gas environments with chlorides

or sulfides. The Product may deteriorate and features may be

affected.

(Notes on storage)

• The technical data provided in the materials of the Product is

intended to describe the representative behaviors and

application of the Product. It is not to guarantee the intellectual

property rights or any other rights of Hirose nor a third party

and not to grant the license.

• Store the Product out of corrosive substances, corrosive gases,

high temperature and humidity or direct sunlight.

Do not apply excessive pressure or vibration to the Product. It

may cause deterioration, deformation, damage or failure of the

Product.

(Notes on the warranties for the contract)

(Notes on resin molded part)

• Unless otherwise provided in a written contract or other

documents (specifications) agreed between the customer and

Hirose, Hirose makes no warranties of any kind (including, but not

limited to, warranties of the function and operation, warranties of

merchantability, warranties of suitability for a specific application or

purpose and warranties of correctness of the information).

• The resin molded part of the Product may contain black spots

or its color may be slightly different, but that has no effect on

the product performance.

2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN

TEL: 81-45-620-3526 Fax: 81-45-591-3726

http://www.hirose.com

http://www.hirose-connectors.com

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.

The contents of this catalog are current as of date of 02/2016. Contents are subject to change without notice for the purpose of improvements.

BF4MC-6GTXRX-B1-5M [HRS]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E