DF58-4S-1.2C [HRS]
Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply;型号: | DF58-4S-1.2C |
厂家: | HRS |
描述: | Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply |
文件: | 总8页 (文件大小:315K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
DF58 Series
Small-sized, low profile connector
1mm
Fig.1
Description of the ViSe Lock Design
■Features
1. Small-sized, low profile connector
Insertion operation appears to be vertical mating.
However, it is actually inserted at an angle which
ensures high retention force in upper direction.
Low profile design of 1.0mm stacking height, the
connector is suitable for small-sized devices.
Before mating
2. Leveling of the vertical mating cable
Vertical insertion of the connector for mating
enhances the assembly operation within device.
3. Proprietary ViSe Lock design
The cable side lock has been strengthened with our
proprietary ViSe Lock mechanism*, preventing the
cables from being easily disconnected due to tough
routing or an excessive load. (*ViSe Lock: Vertical-
insertion Swing-extraction)(Fig.2)*Patent pending
After mating
4. High current capability up the maximum
of 3.0A (2pos. :When 28AWG is used)
By adopting high conductivity material and lowering
contact resistance through optimized contact force,
high-current capability is achieved in spite of its
small size.
Fig.2
Contact design
5. Highly reliable contact design
Effective mating length of 0.29mm is achieved in
spite of low profile 1.0mm stacking height. The
2-point clipping contact stabilizes contact resistance.
Effective mating
length of 0.29mm
2-points of contact
*
6. Halogen-free
*As defined by IEC 61249-2-21
Br-900ppm max, Cl-900ppm max, Br+Cl-1,500ppm max
Cross sectional view of contact face
Fig.3
1
2016.11
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
■Product Specifications
2pos.
3.0A
2.5A
3pos.
2.5A
2.0A
4pos.
2.0A
1.5A
6pos.
Operating temperature range -55ç to 85ç (Note 1)
Operating humidity range 20% to 80% (Note 2)
Current rating
28AWG
30AWG
Rating
Storage temperature range -10ç to 60ç (Note 3)
Storage humidity range 40% to 70% (Note 3)
Voltage rating
100V AC/DC
Item
Specification
Conditions
100V DC
1.Insulation
resistance
100Mø min.
2.Withstanding
voltage
3.Contact
resistance
No flashover or insulation breakdown
10mø max.
500V AC / 1 minute
20mV max. at 1mA.
No electrical discontinuity of 1µs or longer
No damage, cracks or parts dislocation.
Frequency : 10 to 55Hz, single amplitude of 0.75mm,
10 cycles, 3 direction
4.Vibration
5.Shock
2
No electrical discontinuity of 1µs or longer
No damage, cracks or parts dislocation.
Acceleration of 490m/s , 11ms duration, sine half-
wave, 3 cycles in each of the 3 axis
Contact resistance : 20mø max.,
Insulation resistance : 100Mø min.
No damage, cracks or parts dislocation.
6.Humidity
96 hours at 40 2ç, and humidity of 90 to 95%
Contact resistance : 20mø max.,
Insulation resistance : 100Mø min.
No damage, cracks or parts dislocation.
-55°C → 5 to 35°C → 85°C → 5 to 35°C
Times : 30 min. → 2 min. to 3 min. → 30 min. → 2 min.
to 3 min. 5 cycles
7.Temperature
cycle
Contact resistance : 20mø max.,
No damage, cracks or parts dislocation.
8.Durability
10 cycles
9.Resistance to
soldering heat
No deformation of components affecting
performance
Reflow : See recommended temperature profile (Page 6)
Manual soldering : 350°C for 3 seconds
Note 1 : Includes temperature rise caused by operating current.
Note 2 : Use in environments without condensation.
Note 3 : The term "storage" refers to products stored for a long period prior to soldering or usage.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage,
shipment or during transportation.
Materials / Finish
Product
Part
Material
Finish
Black
Tin Plated
Natural
Remarks
Insulator
Contacts
Insulator
Contacts
LCP
Copper Alloy
LCP
UL94V-0
---------------
UL94V-0
Header
Crimp socket
Crimp contacts
Tin Plated
Copper Alloy
---------------
Product Number Structure
■
Refer to the chart below when determining the product specifications from the product number.
Please select from the product numbers listed in this catalog when placing orders.
●Header
Series name
:DF
Contact pitch:1.2mm
Series No.:58
ꢀ V:Straight SMT
Number of contacts:2, 3, 4, 6
Termination section
DF 58 − * P 1.2 V
❹
❺
❻
Connector typeꢀ
ꢀ P:Header
●Crimp socket
Series name:DF
Series No.:58
ꢀ C:Crimp socket
Number of contacts:2, 3, 4, 6
Contact pitch:1.2mm
Termination section
DF 58 − * S − 1.2 C
❹
❺
❻
Connector typeꢀ
ꢀ S:Socket
●Crimp contact
Applicable wire size ꢀ
ꢀ 2830 : 28 to 30AWG
Packaging
SCF:Female crimp contact / reel
ꢀ
DF 58 − 2830 SCF
2
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
■Header (SMT)
A
B
C
Contact No.1
P=1.2
0.95
CAV No.
Vacuum area
Recommended PCB layout
D
HRS mark
C
0.05
P=1.2 0.05
2
0.6+0.05
0
Dmin
0.05
0.85+0.05
1
0
[Specification number]
(21) : Tin plated, Embossed tape
packaging (6,000pcs/reel)
mm
Unit:
Part No.
HRS No.
No. of contacts
A
B
C
D
DF58-2P-1.2V(21)
DF58-3P-1.2V(21)
DF58-4P-1.2V(21)
DF58-6P-1.2V(21)
666-1001-0 21
666-1002-0 21
666-1003-0 21
666-1005-0 21
2
3
4
6
4.5
5.7
6.9
9.3
3.6
4.8
6.0
8.4
1.2
2.4
3.6
6.0
2.5
3.7
4.9
7.3
Note 1 : Embossed tape reel packaging (6,000pcs/reel).
Note : The crossed-hatched area is a no conductive trace area.
2
3
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
●Packaging Specification
●Reel Shape
8
0.1
4
2
0.1
0.1
DMAX
E+0.2
G
G-G
Ø1.5 sprocket
Product label
0
hole far side
G
F
F
F-F
Extraction Direction
mm
Unit:
Part No.
A
B
C
D
E
DF58-2P-1.2V(21)
DF58-3P-1.2V(21)
DF58-4P-1.2V(21)
DF58-6P-1.2V(21)
16
14.25
7.5
22.4
30.4
16.4
24
22.25
11.5
24.4
Crimp socket
A
0.975
Contact No.1 mark
HRS mark
CAV No.
B
C
D
P=1.2
mm
Unit:
Part No.
HRS No.
No. of contacts
A
B
C
D
DF58-2S-1.2C
DF58-3S-1.2C
DF58-4S-1.2C
DF58-6S-1.2C
666-1006-0 00
666-1007-0 00
666-1008-0 00
666-1010-0 00
2
3
4
6
4.6
5.8
7.0
9.4
2.6
3.8
5.0
7.4
3.21
4.41
5.61
8.01
1.2
2.4
3.6
6.0
Note 1 : Please order by number of packing (1,000pcs/packing).
4
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
Crimp contact
■
0.965
t=0.12
1.4
P=4
mm
mm
Unit:
Finish
Tin plated
Part No.
HRS No.
Packaging
Reel
Quantity
40,000
DF58-2830SCF
666-1011-0 00
Note : This product is delivered in 40,000 pieces per reels.
Please place orders in multiples of 40,000 pieces.
●Applicable wire (Tin plated annealed copper wire)
Unit:
Wire size
(Stranded wire conductor)
Jacket outer diameter
Recommended cable
UL1571(Thin wire)
Strip length
28AWG(7/Ø0.127mm)
Ø0.5 to 0.6mm
1.0 to 1.4mm
30AWG(7/Ø0.102mm)
Note 1 : When using other than the recommended wire, contact your nearest Hirose sales representative.
Note 2 : The strip length is a reference value. Please make adjustments so finished crimps will meet the specified values.
Refer to the crimping quality standards (ATAD-H0848-00) for details.
BTools
Unit:mm
Applicable contact
Type
Applicator
Press
Part No.
AP105-DF58-2830S
CM-105C
HRS No.
901-4649-0 00
901-0001-0 00
Under development
550-0179-2 00
DF58-2830SCF
Hand crimping tool
HT307/DF58-2830HC
DF-C-PO(B)
Contact extraction tool
Note : If any trouble has occurred due to tools other than the designated tool, Hirose bears no respoisibility for any trouble.
5
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
BOperating Precautions
1. Recommended Temperature Profile
(Lead-free soldering possible)
10sec MAX
MAX 250
250
220ç
200
180ç
150
100
50
0
TIME(sec)
90‒120sec
60sec
PRE-HEATING TIME SOLDERING TIME
[Applicable Conditions]
1. Peak Temperature : MAX 250℃
2. Heated Area : 220℃ or above, within 60 sec.
3. Pre-heating Area : 150-180℃, 90-120 sec.
4. Number of Operation : Twice or less
* The contact lead area was measured.
The conditions may change depending on the types and manufacturers of
cream solder, PCB size, and conditions of other materials used for
soldering. Please fully check the soldering condition before use.
[Remarks 1] This temperature profile is our recommended value.
2. Recommended Hand Solder Conditions
Soldering iron temperature : 350 10℃, soldering time : within 3 seconds
3. Recommended Screen Thickness, Aperture
Opening Rate (Pattern Area Ratio)
Thickness 0.1mm, aperture opening rate : 100%
4. PCB Warpage
Max 0.02mm at the center of connector with the both edges of the connector
as the baseline.
5. Cleaning Condition
Cleaning with IPA is possible. (Cleaning is not recommended as it may
change the feel of insertion/extraction, etc. Please consult with us when
using other types of cleaning agents.)
6. Precautions
■ Insertion/extraction of the connector while not mounted to the PCB may
cause breakage or deformation to the contact.
■ Do not apply flux at the time of hand soldering, as it may result in flux rise.
■ This product may have slightly different hue on molded items, however,
they do not affect the product performance.
■ See the separate “DF58 Insertion/Extraction Procedure Manual” for
handling precautions at the time of insertion and extraction.
6
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
BUsage Recommendation
7. Insertion
and removal
operation
method
Mating
(1) Placing the crimp socket
ꢀꢀInsert the crimp socket by aligning to the housing outline.
If crimp socket is correctly aligned, the top face of the
crimp socket becomes parallel to the PCB.
(2) Insertion
ꢀꢀPress down in the center of the crimp socket, and mating is complete.
Press down in the center.
Mating is finished.
(3) Checking the mated state
ꢀꢀCheck if the crimp socket is securely mated.
ꢀꢀIf one end floats or is mated at an angle, unmate, and mate it again.
If the connector is inserted when the crimp socket isn't placed correctly, only the friction lock on
the non-cable side may be inserted as shown in the Figure below. In this case, unmate, and
mate it again. Forced mating will lower the retention force.
Insert it over again.
7
DF58 Series●Small-Sized, Low Profile 1.0mm Height, Wire-to-Board Connectors for Power Supply
BRecommended Usage
7. Insertion
and removal
operation
method
Pull-out operation
Pull-out operation starts by hooking on either side of the protrusion to release the crimp socket and
pull up to release the friction lock. Raise the entire crimp socket and complete the operation.
Raise the entire crimp socket
Protrusion for release
Raise either side of the
protrusion
and complete the pull-out
operation
Use the protrusion for release at the time of pull-out operation.
If you forcibly remove it by pulling the cable, cable disconnection and connector breakage will occur.
®
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
+
+
TEL: 81-45-620-3526 Fax: 81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 11/2016. Contents are subject to change without notice for the purpose of improvements.
8
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明