FH27-50S-0.4-SH(05)_技术文档

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

0.4 mm Contact Pitch, 1.2 mm above the board, Flexible Printed Circuit ZIF Connectors

FH 27 Series

●

FPC thickness: 0.2 0.03 mm

●

1.2 mm Height, actuator fully closed.

(54 pos. shown)

1.2mm

4.0mm

■Overview

Continuous miniaturization of personal mobile devices

created a need for a low profile, high density interconnection

system.In the same time, the demand for higher currents and

higher reliability Flexible Printed Circuits has also increased.

Hirose meets all these challenges with introduction of this connector.

24.2mm

●

FPC temporary retention

■Features

1. Low profile, small PCB mounting area, weight reduction

Protruding only 1.2 mm above the board the connector

occupies 50% less area than comparable type having

contacts spaced on 0.5 mm centers.

Creative design, coupled with high manufacturing capabilities

resulted in extremely low weight of the connector.

FPC temporary

hold protrusion

2. Higher current carrying capacity

Contact spacing of 0.4 mm allows production of wider

and simpler pattern of conductive traces on FPC.

FPC notch

3. FPC temporary hold and verification of correct insertion

The connector has built-in FPC hold protrusions allowing

the tactile feel of the correct FPC insertion and holding it

in position before closing of the actuator.

Temporary hold-FPC

fully inserted

4. Uses standard 0.2 mm thick FPC

5. One-finger operation of the actuator

●Wider FPC conductive traces

Proven (in several other Hirose's connectors!) Flip-Lock

rotating actuator assures reliable mechanical and electrical

connection with FPC, confirming it with a definite tactile feel.

0.4mm

0.3mm

0.27mm

0.1mm

6. Board placement with automatic equipment

Flat top surface and packaging on the tape-and reel

allows the use of vacuum nozzles.

Standard reel contains 2,500 connectors.

7. Environmental considerations

The center cores of the embossed tape reels are made of Styrofoam.

8. Variety of contact positions

0.4 mm pitch FPC

0.3 mm pitch FPC

Available with 10, 40, 50,54, 57 and 60 pos.

Metal fittings on each

side do not protrude

out allowing side-by-

side mounting of the

connectors or closer

component placement.

■Applications

Mobile phones, PDA’s, digital cameras, digital video

cameras, LCD connections, plasma displays (PDP), camera

modules and other compact devices requiring Flexible

Printed Circuit connections using high reliability ultra-small

profile connectors

Metal

fitting

67

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

■Product Specifications

Operating temperature range

-55ç to +85ç (Note 2)

Operating humidity range

Storage temperature range

-10ç to +50ç (Note 3)

Storage humidity range

Rated current 0.4 A DC(Note 1)

Rated voltage 40 V AC

Rating

Relative humidity 90% max. (No condensation) Relative humidity 90% max.

Recommended FPC Thickness: = 0.2 0.03mm tin-lead plated (Note 3)

Item

Specification

Conditions

1. Insulation resistance 500 M ø min.

100 V DC

2. Withstanding voltage No flashover or insulation breakdown.

120 V AC /one minute

1 mA

3. Contact resistance

100 m ø max.

* Including FPC conductor resistance

Contact resistance: 100 m ø max.

4. Durability

20 cycles

(insertion/ withdrawal) No damage, cracks, or parts dislocation.

No electrical discontinuity of 1 μs or more.

Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles in

each of the 3 directions.

5. Vibration

Contact resistance: 100 m ø max.

No damage, cracks, or parts dislocation.

No electrical discontinuity of 1 μs. min.

Contact resistance: 100 m ø max.

No damage, cracks, or parts dislocation.

Contact resistance: 100 m ø max.

Insulation resistance: 50 M ø min.

No damage, cracks, or parts dislocation.

Contact resistance: 100 m ø max.

Insulation resistance: 50 M ø min.

No damage, cracks, or parts dislocation.

Acceleration of 981 m/s², 6ms duration, sine half-wave

waveform, 3 cycles / each of 3 axis

6. Shock

7. Humidity

96 hours at 40ç and humidity of 90% to 95%.RH

(Steady state)

Temperature: -55ç / +15ç to +35ç / +85ç / +15ç to +35ç

8. Temperature cycle

Time: 30 / 2 to 3 / 30 / 2 to 3 (Minutes)

5 cycles

9. Resistance to

soldering heat

Reflow: At the recommended temperature profile

Manual soldering: 350ç 10ç for 5 seconds

No deformation of components affecting performance.

Note 1: When passing the current through all of the contacts, use 70% of the current rating.

Note 2: Includes temperature rise caused by current flow.

Note 3: The term ”storage” refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and

Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.

■Materials

Part

Material

Finish

Remarks

UL94V-0

Insulator

Actuator

LCP

Color: Black

Color: Brown

LCP

Contacts

Phosphor bronze

Gold plated (Note 3)

Tin plated

---------------

Metal fittings

■Ordering information

-

FH27 54S 0.4 SH (05)

1

2

3

4

5

Series name: FH27

No. of contacts

Terminal type

1

2

4

5

SH: SMT horizontal mounting type

Plating code

Number of contacts: 10, 40, 50, 54, 57, 60

Contact pitch: 0.4 mm

(05): Gold plated(40,50,60contacts)(RoHS compliant)

(15): Gold plated(10,54,57contacts)(RoHS compliant)

3

68

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BOperation and Precautions

Operation

Precautions

Do not apply excessive force or use any type of tool to operate the

actuator.

1.FPC insertion procedure. Connector installed on

the board.

1

2

3

Lift up the actuator. Use thumb or index finger.

1

Fully insert the FPC in the connector parallel to mounting surface,

with the exposed conductive traces facing down.

The connector will assure reliable performance when the actuator is

open to 130˚maximum. Do not exceed this angle, as this may cause

permanent damage to the connector.

2

Over 130°

FPC conductor

surface

(Bottom side)

Rotate down the actuator until firmly closed. It is critical that the

inserted FPC is not moved and remains fully inserted.

Exercise caution when applying upward force to the connected FPC.

3

The connectors are straight within 0.1 mm max.

Make sure that the PC board connector mounting area flatness

can accept the connector terminals without causing any failure

of the solder joints.

2.FPC removal

4

Lift up the actuator.

1

Carefully withdraw the FPC.

F

Connector

PC board

80

F

80

69

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

■Connector Dimension

A

B

H

0.4

(0.15)

0.15 H

A**

Polarizing mark indicator

Number of contacts indicator

0

K

(0.15)

(1.7)

0.15MAX

1

2

1

2

3

(C: FPC insertion slot dimension)

D

Notes

Lead co-planarity including reinforced metal fittings shall be 0.1 MAX.

1

2

3

The contact terminal lead position indicates the dimension from the K surface, the bottom surface of the insulator body.

Packaging for this product is embossed carrier tape packaging. Refer to packaging specification.

Note that preventive hole for sink mark could be added for improvement.

4

The quality remains good, even with the dark spots, which could occasionally occur on molded plastic.

Unit: mm

RoHS

Part Number

CL No.

Number of Contacts

A

B

C

D

FH27-10S-0.4SH(15)

FH27-40S-0.4SH(05)

FH27-50S-0.4SH(05)

FH27-54S-0.4SH(15)

FH27-57S-0.4SH(15)

FH27-60S-0.4SH(05)

CL580-0004-0-15

CL580-0005-3-05

CL580-0010-3-05

CL580-0001-2-15

CL580-0003-8-15

CL580-0006-6-05

10

40

50

54

57

60

06.6

18.6

22.6

24.2

25.4

26.6

03.6

15.6

19.6

21.2

22.4

23.6

05.24

17.24

21.24

22.84

24.04

25.24

06.0

18.0

22.0

23.6

24.8

26.0

YES

Note1

Note 1 : Refer to "Ordering information".

Note 2 : Tape and reel packaging (2,500 pieces/reel).

Order by number of reels.

70

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BRecommended PCB mounting pattern and metal mask dimensions

E

R

∞Number of contacts

0.23 0.03(Land)

0.04 R

0.4

0.2 0.01(Metal mask)

Recommended metal mask thickness: .t=0.12

(0.225)

Outline of the connector

(0.175)

0.55 0.05

F

0.05

0.55 0.05

BRecommended FPC Dimensions

G

E

0.05

0.03

0.8 0.07

0.27 0.03

0.13 0.03

0.4 0.03

0.2 0.03

R0.2MAX

2-R0.25MAX

(0.07)

Covering film layer

(0.07)

H

G

0.05

Polyimide and thermally hardening adhesive is recommended as the materials for the stiffener.

Overlap between covering film layer and stiffener is 0.5mm min.

1

2

Unit: mm

Part Number

CL No.

Number of Contacts

E

F

G

H

FH27-10S-0.4SH(15)

FH27-40S-0.4SH(05)

FH27-50S-0.4SH(05)

FH27-54S-0.4SH(15)

FH27-57S-0.4SH(15)

FH27-60S-0.4SH(05)

CL580-0004-0-15

CL580-0005-3-05

CL580-0010-3-05

CL580-0001-2-15

CL580-0003-8-15

CL580-0006-6-05

10

40

50

54

57

60

03.6

15.6

19.6

21.2

22.4

23.6

05.5

17.5

21.5

23.1

24.3

25.5

05.2

17.2

21.2

22.8

24.0

25.2

04.01

16.01

20.01

21.61

22.81

24.01

71

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BPackaging Specification

Embossed Carrier Tape Dimensions

●

Tape width up to 24mm .

●

Tape width 32mm and over.

●

2

0.15

12 0.1

4

0.1

(2)

(0.3)

2

0.15

12 0.1

4

0.1

(2)

(0.3)

(4.2)

(5.2)

Unreeling direction

(4.2)

(5.2)

1.5^+0.1

Unreeling direction

0

Reel Dimensions

●

(Q:INSIDE)

(R:OUTSIDE)

End portion

Mounting portion

Lead portion (400mm min.)

Embossed carrier tape

Top cover tape

No connector inserted

(10 pockets min.)

Unit: mm

R

L

M

N

P

Q

Part Number

CL No.

Number of Contacts

FH27-10S-0.4SH(15)

FH27-40S-0.4SH(05)

FH27-50S-0.4SH(05)

FH27-54S-0.4SH(15)

FH27-57S-0.4SH(15)

FH27-60S-0.4SH(05)

CL580-0004-0-15

CL580-0005-3-05

CL580-0010-3-05

CL580-0001-2-15

CL580-0003-8-15

CL580-0006-6-05

10

40

50

54

57

60

16.0

32.0

44.0

-------

28.4

40.4

07.5

14.2

20.2

06.9

18.9

22.9

24.5

25.7

26.9

17.4

33.4

45.4

21.4

37.4

49.4

2,500 pieces per reel.

72

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BRecommended Temperature Profile

Using Lead-free Solder Paste

●

MAX 250ç

250

200

HRS test condition

Solder method

230ç

:Reflow, IR/hot air

(Nihon Den-netsu Co., Ltd.’s Part Number:

SENSBY NR-2)

200ç

Environment

:Room air

150

Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu

(Senju Metal Industry, Co., Ltd.’s Part Number:

150ç

M705-221CM5-42-10.5)

100

50

Test board

Metal mask

:Glass epoxy 45mm∞100mm∞1.6mm thick

Land dimensions:0.23mm∞0.8mm

:0.2∞0.8∞0.12mm thick

25ç

(60sec.) 90 sec. to 120 sec.

(60 sec.)

0

Preheating

Start

Soldering

Time (Seconds)

The temperature profiles shown are based on the above conditions.

In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your

solder paste and equipment manufacturer for specific recommendations.

73

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BFPC Construction (Recommended Specifications)

1. Using Single-sided FPC

Material Name

Covering layer film

Cover adhesive

Material

Thickness (μm)

Top side

Polyimide 1 mil thick.

25

1 to 5 micron nickel underplated

Surface treatment

3

0.2 micron gold palated

Copper foil

Base adhesive

Base film

Cu

1oz

35

25

Polyimide 1 mil thick

25

Reinforcement material adhesive Thermosetting adhesive

30

Stiffener

Polyimide 3 mil thick

Total

75

Bottom side

193

2. Using Double-sided FPC

Material Name

Material

Thickness (μm)

Top side

Covering layer film

Cover adhesive

Polyimide 1 mil thick

25

1 to 5 micron nickel underplated

Surface treatment

3

0.2 micron gold palated

Through-hole copper

Copper foil

Cu

15

18

25

18

25

197

Cu

1/2oz

Base adhesive

Base film

Polyimide 1 mil thick

Base adhesive

Copper foil

Cu

1/2oz

Cover adhesive

Covering layer film

Polyimide 1 mil thick

Reinforcement material adhesive Thermosetting adhesive

Bottom side

Stiffener

Polyimide 1 mil thick

Total

To prevent release of the lock due to FPC bending, use of the FPC with copper foil on bottom side is not recommended.

74


型号：	FH27-50S-0.4-SH(05)
厂家：	HRS
描述：	Card Edge Connector, 50 Contact(s), 1 Row(s), Female, Right Angle, Surface Mount Terminal PC 连接器
文件：	总8页 (文件大小：275K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

FH27-50S-0.4-SH(05) [HRS]

相关型号：

FH27-50S-0.4-SH(51)

FH27-50S-0.4SH

FH27-50S-0.4SH(05)

FH27-54S-0.4-SH

FH27-54S-0.4-SH(05)

FH27-54S-0.4-SH(51)

FH27-54S-0.4SH

FH27-54S-0.4SH(05)

FH27-54S-0.4SH(15)

FH27-54S-0.4SH(51)

FH27-54S-0.4SH(61)

FH27-57S-0.4-SH