FX10A100/10-S-SV121 [HRS]

0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections;


型号：	FX10A100/10-S-SV121
厂家：	HRS
描述：	0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections
文件：	总7页 (文件大小：419K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

NEW

0.5mm Pitch Connectors with Ground Plate for Board-to-Board Connections

FX10 Series

Cross-Section of Mating

✽Features

1. Improved Transmission Efficiency Between

Boards

Transmission characteristics have been improved through

a design that fixes ground plates to both sides of the

header and receptacle.

2. 10 Signal:1 Ground Arrangement

Signal and ground are arranged in a ratio of 10:1 with the

ground plate SMT connected to the board. The ground

stability achieved serves to reduce noise.

3. Reinforced Fittings for Added Solder Weld

Strength

Reinforced fittings provide greater adhesion to the board,

protecting against peeling. The unique connector design

provides a connection between the fitting and the ground

plate for a stronger ground.

4. Suited to High-Density Applications

The signal contact pitch of 0.5 mm produces a smaller

connector utilizing less board area for mounting.

5. Board-To-Board Dimensions of 4mm and 5

mm Are Available

Stack Height

Receptacles

Headers

FX10# –✽S/✽–SV

Dimension H

4mm

FX10#–✽P/✽–SV1

5mm

Note: The thickness of the solder paste is not included in the stack height (dimension H).

✽Applications

Notebook computers, PDA, and other miniature electronic equipment.

2003.7

✽Product Specifications

Operating temperature range

Operating humidity range

-55 to 85ç

Relative humidity 95% or less

(No condensation)

-10 to +60ç (Note 2)

Rated current 0.3 A (Note 1)

Rated voltage 50 V AC

Storage temperature range

Storage humidity range

Rating

-40 to 70% (Note 2)

Item

Requirements

Conditions

1. Insulation resistance

2. Voltage proof

100 Mø or greater

Measured at 100 V DC

No flashover or breakdown

150 V AC applied for one minute

Measured at 100 mA

3. Contact resistance

60 mø or less

No electrical discontinuity for 1µs or greater

No damage, cracks, or parts looseness

No electrical discontinuity for 1µs or longer

No damage, cracks, or parts looseness

Contact resistance of 70 mø or less, insulation resistance of

100 Mø or greater, no damage, cracks, or parts looseness

Frequency: 10 to 55 Hz, amplitude of 0.75 mm in 3 directions, 10

cycles each

4. Vibration

5. Shock

Acceleration of 490 m/s , 11 ms duration, sine half-wave

waveform, for 3 cycles in the both directions of each of the 3 axes

6. Damp heat

(Steady state)

7. Rapid change of

temperature

Temperature of 40ç, humidity of 90 to 95%, duration 96 h

Contact resistance of 70 mø or less, insulation resistance of Temperature: -55ç ✽ 15 to 35ç ✽ 85ç ✽ 15 to 35ç

100 Mø or greater, no damage, cracks, or parts looseness Time: 30 min. ✽ 2 to 3 min. ✽ 30 min. ✽ 2 to 3 min. for 5 cycles

Contact resistance of 70 mø or less

50 times

8. Insertion/Withdrawal life

No damage, cracks, or parts looseness

9. Resistance to

soldering heat

Reflow: At the recommended temperature profile

No melting of resin portion which affects performance

Soldering iron temperature: 300ç·for 3 seconds

Note 1: Please contact us when connector application exceeds 0.3 A rated current.

Note 2: The term storage refers to an unused products prior to board mounting (including packing materials) that is being kept for a long period.

The operating temperature and humidity range are suited to the non-conducting condition following board assembly.

Note 3: The aforementioned specifications are representative of this series. For information on specific parts, confirm with Sales Office.

✽Materials

Part

Material

LCP resin

Process

Beige

Notes

Insulator

UL94V-0

Engagement Area: Gold plating of 0.1µm

Tenmination Area: Solder plating

Engagement Area: Gold plating of 0.1m

Termination Area: Flash plating

Solder plating

Header

Contacts

Phosphor bronze

Receptacle

Ground plate

Phosphor bronze

Reinforced fitting

Tin plating

Note : The black dots on the insulater will not affect performance.

✽Product Number Configuration

Please use this information to discern the product specifications from the product number codes.

To order, please select from the product number codes listed in tables on pages 3 to 5 of this catalog.

FX 10 # ✽ P / ✽ SV 1 (✽✽✽)

Series name: FX

Series No.: 10

Form Symbol

Contact form

SV: Straight SMT

Product height

Blank: Standard

A: With guide post

B: Without guide post

Number of contacts

1 : Standard + 1mm

Packaging classification

Blank: Tray packaging

Signal/Ground: 80/8, 100/10, 120/12,

140/14

(21) : Embossed tape packaging

Connector type

P: Header

S: Receptacle

✽Receptacles

Unit: mm

Notes

Number of Contacts

HRS No.

Product No.

Signal Ground

CL570-0201-4-✽✽✽

CL570-0202-7-✽✽✽

CL570-0203-0-✽✽✽

CL570-0204-2-✽✽✽

CL570-0221-1-✽✽✽

CL570-0222-4-✽✽✽

CL570-0223-7-✽✽✽

CL570-0224-0-✽✽✽

FX10A-080S/08-SV(✽✽✽)

FX10A-100S/10-SV(✽✽✽)

FX10A-120S/12-SV(✽✽✽)

FX10A-140S/14-SV(✽✽✽)

FX10B-080S/08-SV(✽✽✽)

FX10B-100S/10-SV(✽✽✽)

FX10B-120S/12-SV(✽✽✽)

FX10B-140S/14-SV(✽✽✽)

080

100

120

140

080

100

120

140

23.5

29.5

35.5

41.5

23.5

29.5

35.5

41.5

31.1 26.4 31.5 28.3

37.1 32.4 37.5 34.3

43.1 38.4 43.5 40.3

49.1 44.4 49.5 46.3

With guideposts

Without guideposts

31.1

37.1

43.1

49.1

–

31.5 28.3

37.5 34.3

43.5 40.3

49.5 46.3

[Specifications number]- ✽✽✽,(✽✽✽)

Blank: Tray packaging

(21) :Embossed tape packaging

Note 1: There is no polarity in terms of board mounting for this product.

Note 2: The coplanarity of this product's SMT leads is 0.1 mm or less.

Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)

Recommended Land Pattern Dimensions (Metal Mask Dimensions)

Recommended metal mask thickness: 0.15 mm

Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.

2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.

3 Not required in products without guideposts.

✽Headers

✽4mm Mounting Height

Unit: mm

Notes

Number of Contacts

HRS No.

Product No.

Signal Ground

✽✽✽

)

CL570-0001-5-

CL570-0002-8-

CL570-0003-0-

CL570-0004-3-

CL570-0021-2-

CL570-0022-5-

CL570-0023-8-

CL570-0024-0-

FX10A-080P/08-SV(

FX10A-100P/10-SV(

FX10A-120P/12-SV(

FX10A-140P/14-SV(

FX10B-080P/08-SV(

FX10B-100P/10-SV(

FX10B-120P/12-SV(

FX10B-140P/14-SV(

080

100

120

140

080

100

120

140

23.5

29.5

35.5

41.5

23.5

29.5

35.5

41.5

31.1 26.4 31.5 28.3

37.1 32.4 37.5 34.3

43.1 38.4 43.5 40.3

49.1 44.4 49.5 46.3

✽✽✽

)

With guideposts

Without guideposts

✽✽✽

)

✽✽✽

)

✽✽✽

)

31.1

37.1

43.1

49.1

31.5 28.3

37.5 34.3

43.5 40.3

49.5 46.3

✽✽✽

)

✽✽✽

)

✽✽✽

)

[Specifications number] -✽✽✽, (✽✽✽)

Blank: Tray packaging

(21) : Embossed tape packaging

Note 1: There is no polarity in terms of board mounting for this product.

Note 2: The coplanarity of this product's SMT leads is 0.1mm or less.

Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)

Recommended Land Pattern Dimensions (Metal Mask Dimensions)

Recommended metal mask thickness: 0.15 mm

Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.

2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.

3 The cross-hatched area

inside the SMT land may come into contact with the connector contacts

and thus care should be taken that the pattern does not extend beyond the SMT land width.

Not required in products without guideposts.

✽Headers

✽5mm Mounting Height

Unit: mm

Notes

Number of Contacts

HRS No.

Product No.

Signal Ground

✽✽✽

)

CL570-0101-0-

CL570-0102-2-

CL570-0103-5-

CL570-0104-8-

CL570-0121-7-

CL570-0122-0-

CL570-0123-2-

CL570-0124-5-

FX10A-080P/08-SV1(

FX10A-100P/10-SV1(

FX10A-120P/12-SV1(

FX10A-140P/14-SV1(

FX10B-080P/08-SV1(

FX10B-100P/10-SV1(

FX10B-120P/12-SV1(

FX10B-140P/14-SV1(

080

100

120

140

080

100

120

140

23.5

29.5

35.5

41.5

23.5

29.5

35.5

41.5

31.1 26.4 31.5 28.3

37.1 32.4 37.5 34.3

43.1 38.4 43.5 40.3

49.1 44.4 49.5 46.3

✽✽✽

)

With guideposts

Without guideposts

✽✽✽

)

✽✽✽

)

✽✽✽

)

31.1

37.1

43.1

49.1

31.5 28.3

37.5 34.3

43.5 40.3

49.5 46.3

✽✽✽

)

✽✽✽

)

✽✽✽

)

[Specifications number] -✽✽✽,(✽✽✽)

Blank: Tray packaging

(21) : Embossed tape packaging

Note 1: There is no polarity in terms of board mounting for this product.

Note 2: The coplanarity of this product's SMT leads is 0.1 mm or less.

Note 3: Please order embossed tape packaged items by the reel. (One reel holds 1,000 pieces.)

Recommended Land Pattern Dimensions (Metal Mask Dimensions)

Recommended metal mask thickness: 0.15 mm

Note 1 Cross-hatched portions, totaling n places, indicate the ground circuits.

2 Cross-hatched portions, 2 places on both sides, indicate the reinforced fittings.

3 The cross-hatched area

inside the SMT land may come into contact with the connector contacts

and thus care should be taken that the pattern does not extend beyond the SMT land width.

4 Not required in products without guideposts.

BEmbossed Carrier Tape Dimensions

✽Receptacles

Insertion Connector

FX10#-080S/08-SV 20.2 40.4 44 330 45.5 50.5

FX10#-100S/10-SV 26.2 52.4 56 330 59 64

FX10#-120S/12-SV 26.2 52.4 56 330 59 64

FX10#-140S/14-SV 34.2 68.4 72 330 76.5 81.5

Note: There is no polarity in terms of embossed tape

packaging for this product.

✽Headers

Insertion Connector

FX10#-080P/08-SV 20.2 40.4 44 3.8 330 45.5 50.5

FX10#-100P/10-SV 26.2 52.4 56 3.8 330 59 64

FX10#-120P/12-SV 26.2 52.4 56 3.8 330 59 64

FX10#-140P/14-SV 34.2 68.4 72 3.8 330 76.5 81.5

FX10#-080P/08-SV1 20.2 40.4 44 4.8 370 45.5 50.5

FX10#-100P/10-SV1 26.2 52.4 56 4.8 370 59 64

FX10#-120P/12-SV1 26.2 52.4 56 4.8 370 59 64

FX10#-140P/14-SV1 34.2 68.4 72 4.8 370 76.5 81.5

Note: There is no polarity in terms of embossed tape

packaging for this product.

✽Reel Packaging Dimensions

BRecommended Temperature Profile

This temperature profile is a reference for the setting conditions described below. It will differ depending on conditions

and so mounting should follow verification.

Applicable Conditions

Reflow method

Solder

IR reflow

Cream type 63Sn/37Pb

(Flux component of 9wt%)

Glass epoxy. 85 x 110 x 1.6mm

0.15mm

Test substrate

Metal mask thickness

This temperature profile is a recommendation.

Conditions may change somewhat depending on the type

of cream solder and the amount.

BWashing Conditions

Organic Solvent Washing

Solvent

Room temperature washing Heated washing

IPA

Yes

(Isopropyl alcohol)

HCFC

(Hydrochlorofluorocarbon)

Water Type Washing

When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the

documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins.

Be careful that parts are not left with moisture remaining on them.

Washing Precautions

Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the

deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed.

BConnector Handling Precautions

1. Allowable Creepage Dimensions at Time of Mating

The effective coupling length of this product is 1.1 mm for the signal portion and 1 mm for the ground portion. The creepage of

the header and receptacle at the time of mating should be within 0.5 mm of the completely coupled condition.

2. Retension of Boards

Avoid the support of boards by connectors alone and adopt a locking measure that does not rely on the connectors.

3. Solder Repair

Flux may rise as far as the contact portion of the connector depending on the flux coating and other factors at the time of repair.

This will cause poor contact reliability; therefore, before use, the aforementioned washing conditions should be taken into

consideration prior to connector washing.

4. Miscellaneous

·Note that excessive twisting while inserting or withdrawing connectors will cause damage.

·The shade of the molded items may vary somewhat depending on the manufacturing lot; however, this does not affect performance.

FX10A100/10-S-SV121 [HRS]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E