RM15WTPZ-2P [HRS]
General-purpose Multi-Contact Circular Waterproof Connectors;
| 型号： | RM15WTPZ-2P |
| 厂家： | 
HRS |
| 描述： | General-purpose Multi-Contact Circular Waterproof Connectors |
| 文件： | 总16页 (文件大小：627K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
General-purpose Multi-Contact Circular Waterproof Connectors
RM-W Series
Plug _ straight
57
Long backshell
48
■Overview
High performance waterproof circular connectors and cable
Short backshell
assemblies used in variety of applications requiring high
reliability, ease of assembly and small size.
Plug _ Right angle
41
■Features
1. Variety of types
Plugs
: Available in 3 types - straight / long
back shell, straight / short back
shell, right angle back shell.
Receptacles
: Waterproof types with front, back or
flange panel mounting.
Ø23
All types with 2, 3, 4, 8, 10, 12, 15, 20, 31, 40, 55
contacts. Contacts in 2 plating types: gold or silver.
360° Cable exit
Cable
2. Dust and water protection
When fully mated, the connector meet requirements of
IP67 (48 hours at depth of 1.8 m)
(Single-body waterproof receptacles also meet
requirements of IP67.)
3. Cable exit in 360° directions
The right-angle plugs permit exiting of the cable over a
360-degree range in any direction.
■Applications
Base stations, factory automation equipment, robotic
equipment, exploration and construction equipment,
research instrumentation, variety of industrial and
measuring instruments. Any other applications requiring
high reliability waterproof circular connectors.
2006.1
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Product Specifications (RM15WT size products)
600V AC, 840V DC (2 pos.)
500V AC, 700V DC (3, 4, 8 pos.)
Voltage rating
350V AC, 490V DC (10 pos.)
350V AC, 490V DC (12 pos.)
Rating
10A (2, 3, 4 pos.)
Current rating
5A (8, 10, 12 pos.)
Operating temperature range (Note 1)
Storage temperature range (Note 2)
-25ç to +85ç
-25ç to +85ç
Characteristic
Specification
2 m ø max.(2, 3, 4 pos.)
Conditions
1. Contact resistance
1A DC
4 m ø max.(8, 10, 12 pos.)
2. Insulation resistance 1000 M ø min
500V DC
1800V AC/one minute (2 pos.)
2000V AC/one minute (3 pos.)
3. Withstanding voltage No flashover or insulation breakdown.
1500V AC/one minute (4, 8 pos.)
1000V AC/one minute (10, 12 pos.)
Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3
hours in 3 axis.
4. Vibration
No electrical discontinuity for 10µs max.
2
Acceleration of 490m/s , 11ms duration, sine half-wave
5. Shock
No electrical discontinuity for 10µs max.
4 m ø max.(2, 3, 4 pos.)
waveform, 3 cycles in each of the 3 axis.
6. Durability
2000 cycles
(insertion/withdrawal) 8 m ø max.(8, 10, 12 pos.)
Temperature : -55ç ■ Room temperature ■ +85ç ■ Room temperature
7. Temperature cycle
8. Humidity
Insulation resistance: 100 M ø min.
Time
: 30 ■ 10 to 15 ■ 30 ■ 10 to 15 (Minutes)
5 cycles
Insulation resistance: 100 M ø min. (Dray state)
96 hours at temperature 0f 40ç and humidity 0f 90% to 95%.
Complete dust protection. No water penetration
9. Water / dust protection 0When mated with corresponding connector.
when submerged for 48 hours at the depth of 1.8 meter.
Note 1: Includes temperature rise caused by the current flow.
Note 2: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range
Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation.
■Materials
Item
Material
Finish
Remarks
-------------------
UL94V-0
Body
Zinc alloy, brass, pliable PVC
Diallyl phthalate, PBT
Chrome plated or nickel plated
Color: Black
Insulator
Contacts
Gasket
Brass, phosphor bronze, or copper alloy
SIR (black or red), or NBR (gray)
Silver plated or gold plated
Color: black or red (SIR), color: gray (NBR)
-------------------
-------------------
Note: Do not mix different contact plating.
■Ordering Information
(
)
**
4
**
RM 15 W T P
- 2 P
1
2
1
3
5
6
7
1 Series name : RM-W
2 Shell size
5 Number of Contacts
6 Contact type
P : Male contact
S : Female contact
7 Plating
3 Lock type
T : Screw Lock
4 Connector type
P : Plug
(71) : Silver plated
(72) : Gold plated
R : Receptacle
2
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Plugs - straight, long back shell
Wrench opening dimension
of 18 mm
RM15WTPZA-10S(71)
M20∞0.75
M19∞1
45.3
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts Weight RoHS
Part Number
CL No.
Number of Contacts Weight RoHS
RM15WTPZA-2P(ππ)
RM15WTPZA-3P( 72 )
RM15WTPZA-4P(ππ)
RM15WTPZA-8P(ππ)
109-1734-5-ππ
109-1602-4- 72
109-1735-8-ππ
109-1736-0-ππ
2
3
43g
45g
44g
43g
44g
44g
RM15WTPZA-2S(ππ)
RM15WTPZA-3S(ππ)
RM15WTPZA-4S(ππ)
RM15WTPZA-8S(ππ)
109-1729-5-ππ
109-1601-1-ππ
109-1730-4-ππ
109-1731-7-ππ
2
45g
47g
3
4
4
8
45g
45g
45g
45g
YES
YES
8
RM15WTPZA-10P(ππ) 109-1737-3-ππ
RM15WTPZA-12P(ππ) 109-1738-6-ππ
10
12
RM15WTPZA-10S(ππ) 109-1732-0-ππ
RM15WTPZA-12S(ππ) 109-1733-2-ππ
10
12
■Applicable Strain reliefs
■ External cable clamp + internal, self-tightening
JR16WCC-10(72)
Wrench opening dimension
of 21 mm
M20∞0.75
Drive screw(2)
Weight
17.5
(shown one example)
Part Number
JR16WCC-4(72)
JR16WCC-6(72)
JR16WCC-8(72)
CL No.
A
4
6
8
Weight
17.5g
17.5g
17.5g
RoHS
YES
Part Number
CL No.
A
RoHS
YES
114-2052-6-72
114-2053-9-72
114-2054-1-72
JR16WCC-10(72)
JR16WCC-11(72)
JR16WCC-12(72)
114-2055-4-72
114-2154-6-72
114-2056-7-72
10
17.5g
17.5g
17.5g
11
12
■ Internal, self tightening
JR16WCCA-10(72)
Wrench opening dimension
of 21 mm
M20∞0.75
8
(shown one example)
Part Number
CL No.
A
4
6
8
Weight
16g
RoHS
YES
Part Number
CL No.
A
Weight
16g
RoHS
YES
JR16WCCA-4(72)
JR16WCCA-6(72)
JR16WCCA-8(72)
114-2076-4-72
114-2077-7-72
114-2078-0-72
JR16WCCA-10(72)
JR16WCCA-11(72)
JR16WCCA-12(72)
114-2079-2-72
114-2155-9-72
114-2080-1-72
10
11
12
16g
16g
16g
16g
Notes : 1. Cable jacket diameter:Use A 0.2mm
2. When using the self-tightening strain relief verify the cable pull force requirements.
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Plugs - Straight, short back shell
Wrench opening dimension
of 18 mm
RM15WTPZ-10S
M16∞0.75
M19∞1
36.3
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts Weight RoHS
Part Number
CL No.
Number of Contacts Weight RoHS
RM15WTPZ-2P(ππ)
RM15WTPZ-3P(ππ)
RM15WTPZ-4P(ππ)
RM15WTPZ-8P(ππ)
109-1616-9-ππ
109-1622-1-ππ
109-1617-1-ππ
109-1618-4-ππ
2
3
32g
34g
33g
32g
33g
33g
RM15WTPZ-2S(ππ)
RM15WTPZ-3S(ππ)
RM15WTPZ-4S(ππ)
RM15WTPZ-8S(ππ)
109-1611-5-ππ
109-1621-9-ππ
109-1612-8-ππ
109-1613-0-ππ
2
3
34g
36g
34g
34g
34g
34g
4
4
YES
YES
8
8
RM15WTPZ-10P(ππ) 109-1619-7-ππ
RM15WTPZ-12P(ππ) 109-1620-6-ππ
10
12
RM15WTPZ-10S(ππ) 109-1614-3-ππ
RM15WTPZ-12S(ππ) 109-1615-6-ππ
10
12
■Applicable Strain reliefs
■ External cable clamp + internal, self-tightening
JR13WCC-10(72)
Wrench opening dimension
of 17 mm
M16∞0.75
17
Drive screw(2)
(shown one example)
Part Number
JR13WCC-4(72)
JR13WCC-5(72)
JR13WCC-6(72)
CL No.
A
4
5
6
Weight
17g
RoHS
YES
Part Number
CL No.
A
Weight
17g
RoHS
YES
114-2045-0-72
114-2046-3-72
114-2047-6-72
JR13WCC-7(72)
JR13WCC-8(72)
JR13WCC-9(72)
JR13WCC-10(72)
114-2048-9-72
114-2049-1-72
114-2050-0-72
114-2051-3-72
7
8
9
17g
17g
17g
17g
10
17g
■ Internal, self tightening
JR13WCCA-10(72)
Wrench opening dimension
of 17 mm
M16∞0.75
7.5
(shown one example)
Part Number
CL No.
A
4
5
6
Weight
12g
RoHS
YES
Part Number
CL No.
A
Weight
12g
RoHS
YES
JR13WCCA-4(72)
JR13WCCA-5(72)
JR13WCCA-6(72)
114-2069-9-72
114-2070-8-72
114-2071-0-72
JR13WCCA-7(72)
JR13WCCA-8(72)
JR13WCCA-9(72)
114-2072-3-72
114-2073-6-72
114-2074-9-72
7
8
12g
12g
12g
9
12g
JR13WCCA-10(72) 114-2075-1-72
2. When using the self-tightening strain relief verify the cable pull force requirements.
10
12g
Notes : 1. Cable jacket diameter: Use A 0.2mm
4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Plugs - right angle
Wrench opening dimension
of 21.8 mm
RM15WTLP-10S
M16∞0.75
Set screw(2)
Hexagonal hole
opposite side
1.27 mm
M19∞1
39.5
(1.27HEX)
(shown one example)
Part Number
CL No.
Number of Contacts Weight RoHS
Part Number
CL No.
Number of Contacts Weight RoHS
RM15WTLP-12P(71)
109-0997-9-71
12
62.3g YES
RM15WTLP-10S(71)
109-0999-4-71
10
63.1g YES
Notes : 1 Gasket material: NBR, body plating: nickel
2 Recommended set screw tightening torque: 0.2 to 0.3 N•m.
HRS recommended tool: PB205/1.27(CL 150-0066-3)
■Applicable Strain reliefs
■ External cable clamp + internal, self-tightening
(72)
JR13WCC-10
Wrench opening dimension
of 17 mm
M16∞0.75
17
Drive screw(2)
(shown one example)
Part Number
CL No.
A
4
5
6
Weight
17g
RoHS
YES
Part Number
CL No.
A
Weight
17g
RoHS
YES
JR13WCC-4(72)
JR13WCC-5(72)
JR13WCC-6(72)
114-2045-0-72
114-2046-3-72
114-2047-6-72
JR13WCC-7(72)
JR13WCC-8(72)
JR13WCC-9(72)
JR13WCC-10(72)
114-2048-9-72
114-2049-1-72
114-2050-0-72
114-2051-3-72
7
8
17g
17g
17g
9
17g
10
17g
■ Internal, self tightening
JR13WCCA-10(72)
Wrench opening dimension
of 17 mm
M16∞0.75
7.5
(shown one example)
Part Number
CL No.
A
4
5
6
Weight
12g
RoHS
YES
Part Number
CL No.
A
Weight
12g
RoHS
YES
JR13WCCA-4(72)
JR13WCCA-5(72)
JR13WCCA-6(72)
114-2069-9-72
114-2070-8-72
114-2071-0-72
JR13WCCA-7(72)
JR13WCCA-8(72)
JR13WCCA-9(72)
JR13WCCA-10(72)
114-2072-3-72
114-2073-6-72
114-2074-9-72
114-2075-1-72
7
8
12g
12g
12g
9
12g
10
12g
Notes : 1 Cable jacket diameter: Use A 0.2mm
2 When using the self-tightening strain relief verify the cable pull force requirements.
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Receptacles
■■Front panel mount
RM15WTRZ-10S(71)
A
6
Wrench opening
dimension of 18 mm
9
2
M19∞1
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts
A
Weight RoHS
Part Number
CL No.
Number of Contacts
A
Weight RoHS
RM15WTRZ-2P(ππ)
RM15WTRZ-3P(ππ)
RM15WTRZ-4P(ππ)
RM15WTRZ-8P(ππ)
109-1631-2-ππ
109-1632-5-ππ
109-1633-8-ππ
109-1634-0-ππ
2
3
21 13g
22.1 15g
21 14g
RM15WTRZ-2S(ππ)
RM15WTRZ-3S(ππ)
RM15WTRZ-4S(ππ)
RM15WTRZ-8S(ππ)
109-1637-9-ππ
109-1638-1-ππ
109-1639-4-ππ
109-1640-3-ππ
2
3
21.75 15g
22.1 17g
21.75 15g
21.6 15g
21.6 15g
21.6 15g
4
4
YES
YES
8
20.65 13g
20.65 14g
20.65 14g
8
RM15WTRZ-10P(ππ) 109-1635-3-ππ
RM15WTRZ-12P(ππ) 109-1636-6-ππ
10
12
RM15WTRZ-10S(ππ) 109-1641-6-ππ
RM15WTRZ-12S(ππ) 109-1642-9-ππ
10
12
Notes : Recommended nut tightening torque: 3N•m
■■Rear panel mount
RM15WTRZA-10S(71)
A
13
6.5
2
24(HEX)
M19∞1
M21∞1
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts
A
Weight RoHS
Part Number
CL No.
Number of Contacts
A
Weight RoHS
RM15WTRZA-2P(ππ) 109-1651-0-ππ
RM15WTRZA-3P(ππ) 109-1652-2-ππ
RM15WTRZA-4P(ππ) 109-1653-5-ππ
RM15WTRZA-8P(ππ) 109-1654-8-ππ
RM15WTRZA-10P(ππ) 109-1655-0-ππ
RM15WTRZA-12P(ππ) 109-1656-3-ππ
2
3
21 22g
22.1 24g
21 23g
RM15WTRZA-2S(ππ) 109-1657-6-ππ
RM15WTRZA-3S(ππ) 109-1658-9-ππ
RM15WTRZA-4S(ππ) 109-1659-1-ππ
RM15WTRZA-8S(ππ) 109-1660-0-ππ
RM15WTRZA-10S(ππ) 109-1661-3-ππ
RM15WTRZA-12S(ππ) 109-1662-6-ππ
2
3
21.75 24g
22.1 26g
21.75 24g
21.6 24g
21.6 24g
21.6 24g
4
4
YES
YES
8
20.65 22g
20.65 23g
20.65 23g
8
10
12
10
12
Notes : Recommended nut tightening torque: 3N•m
6
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Receptacles (Square flange)
■■Waterproof (When mated with corresponding plug)
A
6
RM15WTRZB-10S(71)
28
20.6
9
2
M19∞1
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts
A
Weight RoHS
Part Number
CL No.
Number of Contacts
A
Weight RoHS
RM15WTRZB-2P(ππ) 109-1671-7-ππ
RM15WTRZB-3P(ππ) 109-1672-0-ππ
RM15WTRZB-4P(ππ) 109-1673-2-ππ
RM15WTRZB-8P(ππ) 109-1674-5-ππ
RM15WTRZB-10P(ππ) 109-1675-8-ππ
RM15WTRZB-12P(ππ) 109-1676-0-ππ
2
3
21 19g
22.1 21g
21 20g
RM15WTRZB-2S(ππ) 109-1677-3-ππ
RM15WTRZB-3S(ππ) 109-1678-6-ππ
RM15WTRZB-4S(ππ) 109-1679-9-ππ
RM15WTRZB-8S(ππ) 109-1680-8-ππ
RM15WTRZB-10S(ππ) 109-1681-0-ππ
RM15WTRZB-12S(ππ) 109-1682-3-ππ
2
3
21.75 21g
22.1 23g
21.75 21g
21.6 21g
21.6 21g
21.6 21g
4
4
YES
YES
8
20.65 19g
20.65 20g
20.65 20g
8
10
12
10
12
Notes : 1. Screw size: M3
2. Recommended nut tightening torque : 0.3 to 0.35N•m
■■Waterproof (single body)
A
6
JR15WTRZB-10PA(71)
28
20.6
9
2
M19∞1
(shown one example)
[Specification number] (**), -**
(71) : Silver plated contacts
(72) : Gold plated contacts
Part Number
CL No.
Number of Contacts
A
Weight RoHS
Part Number
CL No.
109-1694-2
109-1695-5
Number of Contacts
A
Weight RoHS
RM15WTRZB-3PA(ππ)
RM15WTRZB-4PA(ππ)
109-1692-7
109-1693-0
3
4
22.1 20g
21 21g
RM15WTRZB-8PA(ππ)
RM15WTRZB-10PA(ππ)
8
20.65 22g
20.6 24g
YES
YES
10
Notes : 1. Screw size: M3
2. Recommended nut tightening torque : 0.3 to 0.35N•m
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
BPlug -- Disassembly / Assembly
Clamp
Bushing
Tightening collar
Screw
3 min
Insulator body (P)
Contacts
Washer
Cable jacket
Cable
Wires
Conductors
A
B
Back shell
Coupling
Strain relief clamp
Cable
Back shell
Table 1
Part Name
Number of Contacts
A
B
Tightening ring
3
6mm
3mm
6mm
3mm
3mm
21mm
21mm
12mm
12mm
25mm
RM15WTPZA-ππ
2,4,8,10,12
3
RM15WTPZ-ππ
RM15WTLP-ππ
2,4,8,10,12
10,12
Set screw(2)
Disassembly
1 Fix the plug in the assembly fixture (RM15TP-T01 (CL150-0098-0)), then remove the insulator body (P) and the back shell.
Right-angle plugs have set screws in the tightening ring at 2 locations. Loosen the set screws before removing the back shell.
2 Remove the 2 screws of the strain relief clamp, and then remove the clamp from the tightening collar.
1.
2.
Wiring
1 Assure that the cable outer diameter will fit the strain relief clamp, and is prepared as recommended in Table 1.
It is recommended that the exposed conductors be pre-soldered, to assure easier insertion in the soldering cup.
2 Pass the parts over the cable in the order of: tightening collar, washer, bushing, back shell, and coupling. Refer to the drawings
(above) for assembly orientation of all components.
3 Solder the wires to the contacts of the insulator body (P).
Use of heat-shrink tubing or another insulating media between the soldered contacts is suggested.
Connector Assembly
Straight Plugs
1 Place the completely wired insulator body (P) in the assembly fixture secured in a vise. Insert in the coupling, then back shell. The
back shell should be tightened to a torque of 3 N•m.
Right-angle Plugs
1 Place the completely wired insulator body (P) in an assembly fixture secured by a vise. Insert in the coupling, then back shell (with
tightening ring). When attaching the back shell, orient the cable in the desired direction and fasten the tightening ring to the
insulator body (P) with a torque of 3 N•m. After this, tighten and fix the 2 sets crews with a torque of 0.2 to 0.3 N•m.
Additional assembly recommendations:
3.
In applications where continuous extremely high vibrations may be encountered it is recommended that a thread locking
compound be applied to male threads prior to assembly (Loctite 271 ˛ manufactured by Henkel Japan K.K. or equivalent)
Waterproof verification - plug assembly
Apply air pressure of 17.6 kPa for 30 seconds from the mating side of the plug assembly. There shall not be any air leakage from
inside the connector when submerged in the water tank.
4.
5.
Precautions
1 Follow the correct assembly sequence, cable preparation and tightening torques.
2 Assure that the applicable cable outer surfaces are free of scratches, oil, grease or any other contamination.
3 Do not use excessive forces or improper tools when assembling or mounting the connectors.
8
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
BReceptacle - recommended panel cut-outs
Front mounting, rear nut
Rear mounting, front nut
Square flange, screw mounting
4-M3∞0.5
20.6 0.05
1.4 0.05
Panel thickness: 0.5 to 2 mm
Panel thickness: 0.5 to 2.5 mm
Panel thickness: 2.5 to 4 mm
For RM15WTRZ receptacles
For RM15WTRZA receptacles
For RM15WTRZB receptacles
Notes : 1. When attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. Do not pinch the gasket.
Notes : 2. The view of the above diagrams is from the receptacle mating side.
Notes : 3. The ■ symbol in the above diagrams indicates the coupling guide position of the receptacles.
BContact Position Arrangement and Specifications
Shell size : 15
Contact
configuration
Number of contacts
Withstanding voltage
Current rating
2
3
4
8
10
12
1800V AC / 1 minute 2000V AC / 1 minute 1500V AC / 1 minute 1500V AC / 1 minute 1000V AC / 1 minute 1000V AC / 1 minute
10A
10A
10A
5A
5A
5A
Insulation resistance
Contact resistance
Solder pot inner diameter
1000Mø min.
2mø max.
1.7mm
1000Mø min.
2mø max.
2.8mm
1000Mø min.
2mø max.
1.7mm
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
Notes : 1. The contact configuration as viewed from the wiring side.
Notes : 2. The ■ symbol in the above diagrams indicates the coupling guide position of the receptacles.
Notes : 3. Withstanding voltages indicate test voltage values.
BPrecautions
1. Switch off the power of the circuit before disconnecting or plugging- in the connectors.
2. Use a connectors with socket contacts at the power side of the circuit.
3. Make sure that the coupling is in completely cocked position.
4. Use correct plug / receptacle to assure dust and water protection.
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Product Specifications (RM21WT to RM31WT size products)
600V AC, 840V DC (40 pos.)
Voltage rating
500V AC, 700V DC (15, 31, 55 pos.)
350V AC, 490V DC (20 pos.)
Rating
Current rating
5A
Operating temperature range (Note 1)
Storage temperature range (Note 2)
-25ç to +85ç
-25ç to +85ç
Characteristic
Specification
Conditions
1A DC
1. Contact resistance
4 m ø max.
2. Insulation resistance 1000 M ø min
500V DC
1800V AC/one minute (4 pos.)
1500V AC/one minute (15, 31, 55 pos.)
1000V AC/one minute (20 pos.)
Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3
hours in 3 axis.
3. Withstanding voltage No flashover or insulation breakdown.
4. Vibration
5. Shock
No electrical discontinuity for 10µs max.
No electrical discontinuity for 10µs max.
8 m ø max.
2
Acceleration of 490m/s , 11ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
6. Durability
2000 cycles
(insertion/withdrawal)
Temperature : -55ç ■ Room temperature ■ +85ç ■ Room temperature
7. Temperature cycle
8. Humidity
Insulation resistance: 100 M ø min.
Time
: 30 ■ 10 to 15 ■ 30 ■ 10 to 15 (Minutes)
5 cycles
Insulation resistance: 100 M ø min. (Dray state)
96 hours at temperature 0f 40ç and humidity 0f 90% to 95%.
Complete dust protection. No water penetration
9. Water / dust protection 0When mated with corresponding connector.
when submerged for 48 hours at the depth of 1.8 meter.
Note 1: Includes temperature rise caused by the current flow.
Note 2: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range
Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation.
■Materials
Item
Material
Brass
Finish
Chrome plated or nickel plated
Color: Black
Remarks
-------------------
UL94V-0
Body
Insulator
Diallyl phthalate
Brass, copper alloy
Chloroprene rubber or SIR
Contacts
Gasket
Silver plated or gold plated
Color: black
-------------------
-------------------
Note: Do not mix different contact plating.
■Ordering Information
(
)
( ) (
RM 21 W T P - CP 10
)
**
**
4
**
RM 21 W T P
- 2 P
1
2
1
3
5
6
7
8
9
1 Series name : RM-W
2 Shell size
5 Number of Contacts
6 Contact type
P : Male contact
S : Female contact
7 Plating
8
CP: Strain relief
9 () with
() without : Internal cable clamp
4~18 : Cable size
: External cable clamp
3 Lock type
T : Screw Lock
4 Connector type
P : Plug
(71) : Silver plated
(72) : Gold plated
R : Receptacle
10
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Plugs - straight, long back shell
RM21WTPS-15S(71)
Wrench opening dimension D
F
E
C
(shown one example)
Part Number
CL No.
Number of Contacts
ØA
21
ØB
32
36
36
C
D
E
F
Weight
Remarks
RoHS
YES
RM21WTPS-15S(71) 109-1860-0-71
RM24WTPB-31S(71) 109-1852-1-71
RM24WTPB-31P(71) 109-1855-0-71
15
31
31
49
54
54
23
26
26
TM25∞2 M20∞0.75 104.5
TM29∞2 M24∞0.75 144.6
TM29∞2 M24∞0.75 140.0
Silver plated
only
24.3
24.3
■Applicable Strain reliefs
■ External cable clamp + internal, self-tightening
E
RM24WTP-CP14(71)
Wrench opening dimension D
C
(shown one example)
Weight
Part Number
JR16WCC-4(72)
JR16WCC-6(72)
JR16WCC-8(72)
JR16WCC-10(72)
JR16WCC-11(72)
JR16WCC-12(72)
RM24WTP-CP14(71)
CL No.
ØA
04
06
08
10
11
12
14
ØB
23
23
23
23
23
23
29
C
D
E
Remarks
RoHS
YES
114-2052-6-72
114-2053-9-72
114-2054-1-72
114-2055-4-72
114-2154-6-72
114-2056-7-72
109-1851-9-71
17.5
17.5
17.5
17.5
17.5
17.5
17.5
21
21
21
21
21
21
26
M20∞0.75
M20∞0.75
M20∞0.75
M20∞0.75
M20∞0.75
M20∞0.75
M24∞0.75
17.5g
17.5g
17.5g
17.5g
17.5g
17.5g
17.5g
For RM21WT
For RM24WT
Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N•m.
HRS recommended tool : PB205/1.27(CL 150-0066-3)
■ Internal, self tightening
E
RM21WTP-CP(8)(71)
Set screw
D
C
(shown one example)
Part Number
CL No.
ØA
08
10
12
10
12
14
16
ØB
23
23
23
27
27
27
27
C
D
E
Weight
22.5
22.0
21.5
28.5
28.5
28.0
26.5
Remarks
RoHS
YES
RM21WTP-CP(8)(71)
RM21WTP-CP(10)(71)
RM21WTP-CP(12)(71)
RM24WTP-CP(10)(71)
RM24WTP-CP(12)(71)
RM24WTP-CP(14)(71)
RM24WTP-CP(16)(71)
109-1405-3-71
109-1406-6-71
109-1407-9-71
109-1493-0-71
109-1494-3-71
109-1495-6-71
109-1496-9-71
38
7.5
7.5
7.5
8
M20∞0.75
M20∞0.75
M20∞0.75
M24∞0.75
M24∞0.75
M24∞0.75
M24∞0.75
38
For RM21WT
38
38.5
38.5
38.5
38.5
8
For RM24WT
8
8
Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N•m.
Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements.
11
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Plugs - Straight, short back shell
D
RM21WTP-15S(71)
Set screw
E
C
(shown one example)
Part Number
CL No.
Number of Contacts
ØA
ØB
32
32
32
32
36
36
42
42
42
42
C
E
F
Weight
88.5
88.5
85
Remarks
RoHS
YES
RM21WTP-15S(71)
RM21WTP-20S(71)
RM21WTP-15P(71)
RM21WTP-20P(71)
RM24WTP-31S(71)
RM24WTP-31P(71)
RM31WTP-40S(71)
RM31WTP-55S(71)
RM31WTP-40P(71)
RM31WTP-55P(71)
109-1401-2-71
109-1402-5-71
109-1403-8-71
109-1404-0-71
109-1491-5-71
109-1492-8-71
109-1571-2-71
109-1572-5-71
109-1573-8-71
109-1574-0-71
15
20
15
20
31
31
40
55
40
55
21
37.5
37.5
37.5
37.5
44
TM25∞2
TM25∞2
TM25∞2
TM25∞2
TM29∞2
TM29∞2
TM35∞2
TM35∞2
TM35∞2
TM35∞2
M20∞0.75
M20∞0.75
M20∞0.75
M20∞0.75
M24∞0.75
M24∞0.75
M28∞0.75
M28∞0.75
M28∞0.75
M28∞0.75
21
21
21
85
Silver plated
only
24.3
24.3
30.8
30.8
30.8
30.8
128
123
152
157
152
150
44
52
52
52
52
Notes : Recommended set screw tightening torque : 0.2 to 0.3 N•m.
■Applicable Strain reliefs
■ External cable clamp + internal, self-tightening
E
RM24WTP-CP14(71)
Wrench opening dimension D
C
(shown one example)
Part Number
CL No.
ØA
10
12
14
ØB
25
25
29
C
17
D
E
RoHS
YES
RM21WTP-CP10(71)
RM21WTP-CP12(71)
RM24WTP-CP14(71)
109-1478-7-71
109-1477-4-71
109-1851-9-71
21
21
26
M20∞0.75
M20∞0.75
M24∞0.75
17
17.5
Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N•m.
HRS recommended tool : PB205/1.27(CL 150-0066-3)
■ Internal, self tightening
E
RM21WTP-CP(8)(71)
Set screw
D
C
(shown one example)
Part Number
CL No.
ØA
08
10
12
10
12
14
16
10
12
14
16
18
ØB
23
23
23
27
27
27
27
31
31
31
31
31
C
D
E
Weight
22.5
22
21.5
28.5
28.5
28.5
28.5
46
46
45
43.5
42
RoHS
YES
RM21WTP-CP(8)(71)
RM21WTP-CP(10)(71)
RM21WTP-CP(12)(71)
RM24WTP-CP(10)(71)
RM24WTP-CP(12)(71)
RM24WTP-CP(14)(71)
RM24WTP-CP(16)(71)
RM31WTP-CP(10)(71)
RM31WTP-CP(12)(71)
RM31WTP-CP(14)(71)
RM31WTP-CP(16)(71)
RM31WTP-CP(18)(71)
109-1405-3-71
109-1406-6-71
109-1407-9-71
109-1493-0-71
109-1494-3-71
109-1495-6-71
109-1496-9-71
109-1575-3-71
109-1576-6-71
109-1579-4-71
109-1577-9-71
109-1578-1-71
38
7.5
7.5
7.5
8
M20∞0.75
M20∞0.75
M20∞0.75
M24∞0.75
M24∞0.75
M24∞0.75
M24∞0.75
M28∞0.75
M28∞0.75
M28∞0.75
M28∞0.75
M28∞0.75
38
38
38.5
38.5
38.5
38.5
42
8
8
8
12
42
12
12
12
12
42
42
42
Notes : 1. Cable jacket diameter:Use A 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N•m.
Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements.
12
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
■Receptacles
■■Front panel mount
RM21WTR-15P(71)
C
D
F
B
E
(shown one example)
Part Number
CL No.
Number of Contacts
ØA
31
31
31
31
35
35
41
41
41
41
B
C
D
2
E
E
Weight
Remarks
RoHS
RM21WTR-15P(71)
RM21WTR-15S(71)
RM21WTR-20P(71)
RM21WTR-20S(71)
RM24WTR-31P(71)
RM24WTR-31S(71)
RM31WTR-40P(71)
RM31WTR-40S(71)
RM31WTR-55P(71)
RM31WTR-55S(71)
109-1445-8-71
109-1447-3-71
109-1446-0-71
109-1448-6-71
109-1483-7-71
109-1484-0-71
109-1525-5-71
109-1527-0-71
109-1526-8-71
109-1528-3-71
15
15
20
20
31
31
40
40
55
55
21
21
21
21
21
21
21
21
21
21
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
23.5 TM25∞2
23.5 TM25∞2
23.5 TM25∞2
23.5 TM25∞2
28
2
31.5
31.5
31.5
41.5
42
2
2
2.5
2.5
2.5
2.5
2.5
2.5
28
28
34
34
34
34
TM29∞2
TM29∞2
TM35∞2
TM35∞2
TM35∞2
TM35∞2
Silver plated
only
YES
50
52
53.5
54
Notes : Recommended nut tightening torque : 3 N•m
■■Waterproof (single body)
RM21WTRK-20P(71)
32
24
20.6 2
6
TM25∞2
TM25∞2
(shown one example)
Part Number
RM21WTRK-20P(71)
Notes : 1. Screw size : M3
CL No.
Number of Contacts
20
Remarks
RoHS
YES
109-1466-8-71
Gold plated only
2. Recommended nut tightening torque : 0.3 to 0.35 N•m
3. Use a 1.9 to 2.0 mm dia.thick O-ring for the waterproof gasket that is used in the connector mounting portion.
13
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
BReceptacle - recommended panel cut-out
Front mounting, rear nut
Square flange, screw mounting
1.4 0.05
24 0.05
4–M3∞0.5
B
Panel thickness: 0.5 to 2 mm
Panel thickness: 2.5 to 4 mm
For RM**WTR receptacles
For RM21WTRK receptacles
Part Number
For RM21WTR
ØA
B
RC
0.8
22.1
26.1
32.1
13.3
15.1
18.3
For RM24WTR
0.8
For RM31WTR
0.85
Notes : Tolelance is +0.1/0.
Notes : 1. When attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. Do not pinch the gasket.
Notes : 2. The view of the above diagrams is from the receptacle mating side.
Notes : 3. The ■ symbol in the above diagrams indicates the coupling guide position of the receptacles.
BContact Position Arrangement and Specifications
Shell size : 21
Shell size : 24
Shell size : 31
18
1
1
17
35
47
19
37
49
55
2
19
32
39
2
20
3
22
23
16
36
1
20
33
18
12
24 13
3
21
21
10
1
11
23
14
2
17
34
38
50
48
54
18
19
Contact
31
4
15
39
4
17
16
22
9
8
2
3
25 15
3
11
12
30
16
33
34
35
25
5
10
22
30
29
40
31
configuration
23
24
14
13
5
15
14
38
16
5
26
29
28
46
45
30
11
40
41
26
8
6
20
14
24
25
7
32
31
12
53
44
29
10
51
42
27
9
4
9
27
13
5
4
21
17
7
37
15
6
6
52
43
28
36
7
28
8
18
20 19
7
13
27
11
8
6
26
10
12
9
Number of contacts
Withstanding voltage
Current rating
15
20
31
40
55
1500V AC / 1 minute 1000V AC / 1 minute 1500V AC / 1 minute
1800V AC / 1 minute
5A
1500V AC / 1 minute
5A
5A
5A
5A
Insulation resistance
Contact resistance
Solder pot inner diameter
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
1000Mø min.
4mø max.
1.1mm
Notes : 1. The contact configuration as viewed from the wiring side.
Notes : 2. The ■ symbol in the above diagrams indicates the coupling guide position of the receptacles.
Notes : 3. Withstanding voltages indicate test voltage values.
BPrecautions
1. Switch off the power of the circuit before disconnecting or plugging- in the connectors.
2. Use a connectors with socket contacts at the power side of the circuit.
3. Make sure that the coupling is in completely cocked position.
4. Use correct plug / receptacle to assure dust and water protection.
14
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明