W.FL-R-SMT-1 [HRS]
Ultra Small Surface Mount Coaxial Connectors - 1.4mm Mated Height; 超小型表面贴装同轴连接器 - 1.4毫米插配高度型号: | W.FL-R-SMT-1 |
厂家: | HRS |
描述: | Ultra Small Surface Mount Coaxial Connectors - 1.4mm Mated Height |
文件: | 总6页 (文件大小:387K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NEW
Ultra Small Surface Mount Coaxial Connectors – 1.4mm Mated Height
W.FL Series – Further downsizing of FL series in response to the market needs.
Occupied Mounting Area
2.0
2.0
ꢀFeatures
ꢀ
Mated Height Comparison(With U.FL series)
2
1. Mounting area of only 3.4mm
2. The board mounted receptacle weights only 5.6 mg
3. Accepts high frequency transmission of DC to 6GHz
U.FL-LP-040
U.FL-LP-066
4. Receptacle supplied on tape-and-reel for
4. placement on the board with automatic equipment
U.FL-LP(V)-040
W.FL-LP-040
5. Plugs are terminated with ultra-fine Teflon®
4. insulated coaxial cables
W.FL Series
U.FL Series
6. Un-mating with a simple tool
ꢀApplications
Mobile phones, Wireless LAN, Bluetooth protocol
devices, PDA, GPS, electronic measuring instruments
and any application requiring high frequency
transmission over coaxial line, where space is limited.
Plug
2.85
Cable
Dia. 0.81
W.FL-R-SMT-1
Receptacle
* Teflon is a registered trademark of DuPont.
2004.4
1
ꢀProduct Specifications
Nominal characteristic
-40
(Relative humidity 90% max.)
-40 to +70
(Relative humidity 90% max.)
ç to +90ç
50 ohms
Operating temperature range
Operating humidity
impedance
Ratings
ç
ç
Frequency range
DC to 6GHz
ꢀMaterials and Finishes
Item
Specification
1. Contact resistance
2. Insulation resistance
3. Withstanding voltage
Center: 20m ohms max. Outside: 10m ohms max.
500M ohms min., 100V DC
200V AC / 1 minute
1.3 max. (Up to 3GHz)
4. V.S.W.R.(Note)
1.35 max. (3 to 6GHz)
Note:V.S.W.R. Measurement System
Note:Measured as shown on the block diagram below.
Note:Test connection and measurement setup.
Note1:Cable type connector measurements.
Network Analyzer
Test Set
With SMA conversion adapters mated with W.FL plug
at each end of the 100cm long ultra-fine coaxial cable.
Note2:Board type connector measurements.
Test Port
D.U.T Termination
Test Port Cable
Mounted on
a 50 ohms glass epoxy board.
Measurements were conducted with SMA conversion
adapters attached.
ꢀMaterial/Finishes
Part
Component
Shell
Material
Finish/Remarks
Silver plated
Phosphor bronze
PBT
Plug
Insulator
Black, UL94V-0
Gold plated
Socket center contact
Shell
Phosphor bronze
Phosphor bronze
LCP
Silver plated
Receptacle
Insulator
Black, UL94V-0
Gold plated
Pin center contact
Brass
ꢀPlug
2.85
Plugs can be ordered only terminated to the cable.
2
ꢀHow to Specify Cable Assembly
Double-ended cable assembly
Single-ended cable assembly
***
L(mm)
L(mm)
Ordering Information
Standard tolerances for (L)**
ꢀ
ꢀ
(L)(mm)
*L=35 to 200
L=200 to 500
L=500 to 1000
Standard Tolerance (mm)
[ ]
--
--
--
--
W.FL 2LP 04N
A (L)
4
1
2
3
4
5
8
12
1.5% of (L)
L=1000
/
1 Series name
W.FL
*Minimum available length (L) is 35mm
**Contact nearest HRS representative if different
tolerances are required.
LP2: Single ended
2LP: Double ended
2 Assembly type
***Contact Nearest HRS representative if one end
requires preparation.
3 Cable type
04N: 0.81mm dia. ultra-fine coaxial cable
1: White, 2: Black
4 Cable color
5 Total length (mm)
Length (L)
ꢀReceptacle
BRecommended PCB Mounting Pattern
2.6
1.4
0.85
0.3
0.25
0.5
0.3
SIGNAL TERMINAL
SIGNAL
TERMINAL
PAD
1.7
2
GND
GND
No conductive traces in this area
Recommended screen thickness: 0.1mm to 0.12mm
Part Number
CL No.
Packaging
Weight / EA
W.FL-R-SMT-1(10)
331-0482-6-10
5.6 mg
Reel packaging (2000 pieces/reel)
3
ꢀConversion Adapters
ꢀ SMA Conversion Adapter (W.FL side jack – SMA side plug)
(10.3)
8HEX
W.FL
SMA
Note:Used for performance measurements only.
The W.FL mating side has lower retention
Part No.
CL No.
force than the regular product when mated to
the corresponding part.
HRMP-W.FLJ
311-0367-3
ꢀ SMA Conversion Adapter (W.FL side plug – SMA side jack)
13.8
4.05
6
(
)
5.6
SMA
W.FL
1/4-36UNS-2A
Note:Used for performance measurements only.
The W.FL mating side has lower retention
force than the regular product when mated to
the corresponding part.
Part No.
CL No.
HRMJ-W.FLP
311-0368-6
ꢀ SMA Conversion Adapter
( 18.35
)
6
( 4 )
5.5
1/4-36UNS-2A
Note:When mating with corresponding part (W.FL-
R-SMT-1) it must be pressed down and held
to make complete connection.
Part No.
CL No.
HRMJ-W.FLP-ST1
311-0386-8
ꢀReceptacle Inspection Adapter
ꢀ Used for inspecting the performance parameters of the cable assembly.
12.1
( 7.9)
( 4.4 )
4.2
1
7HEX
M5∞0.5
Part No.
CL No.
W.FL-R-1
331-0483-9
4
ꢀPlug Extraction Tool-Used for Un-mating of the plug
(100 )
40
Part No.
CL No.
W.FL-LP-N
331-0492-0
BPackaging Specifications- Receptacle
W.FL-R-SMT-1(10)
Embossed Carrier Tape Dimensions
2
4
Center contact terminal
8
Unreeling direction
Reel Dimensions
14
1.8
5
ꢀUsage Precautions
1. Plugs
1) Mating.
1) Both parts must be aligned on the axis to mate correct. Press down firmly. A tactile “click” will confirm fully
mated condition.
2) Un-mating.
1) Fully insert the tool under the plug’s flanges as shown.
(1) Mating/ un-mating
W.FL-LP-N plug extraction tool
1) Apply even force upward until the plug is free.
W.FL Cable
Assembly
W.FL-R-SMT-1
Do not twist, apply excessive forces or sharp bends to the cable.
W.FL-LP-040
Cable Assembly
×
W.FL-R-SMT-1
(2) Cable handling
2N max
Receptacle
×
(3) Precautions
Do NOT forcefully twist or deform wires.
2. Receptacles
(1) Recommended soldering
temperature profile
Peak temperature and time
[ç]
240ç 3 seconds
260
240
220
200
183ç
180
160
140
120
100
80
Preheating (130ç to 165ç)
Within 2 minutes
40 to 50 seconds
Time
1) The temperature profile indicates the board surface temperature at the point of contacts with the connector
terminals.
2) The temperature may vary, depending on the board size, the solder paste type and thickness.
0.1 to 0.12 mm
(2) Recommended screen thickness
®
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
http://www.hirose-connectors.com
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
6
相关型号:
W.FL-R-SMT-1(60)
RF Connector, 1 Contact(s), Male, Board Mount, Surface Mount Terminal, Receptacle
HRS
W.FL2-R-SMT-1(10)
RF Connector, 1 Contact(s), Male, Board Mount, Surface Mount Terminal, Receptacle, ROHS COMPLIANT
HRS
W.FL2-R-SMT-1(60)
RF Connector, 1 Contact(s), Male, Board Mount, Surface Mount Terminal, Receptacle
HRS
W.FL2-R-SMT-1(80)
RF Connector, 1 Contact(s), Male, Board Mount, Surface Mount Terminal, Receptacle
HRS
©2020 ICPDF网 联系我们和版权申明