H34063 [HSMC]
DC-TO-DC Converter Integrate Circuit Devices; 直流 - 直流转换器集成电路器件型号: | H34063 |
厂家: | HI-SINCERITY MOCROELECTRONICS |
描述: | DC-TO-DC Converter Integrate Circuit Devices |
文件: | 总6页 (文件大小:72K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 1/6
HI-SINCERITY
MICROELECTRONICS CORP.
H34063AP
DC-TO-DC CONVERTER INTEGRATE CIRCUIT DEVICES
Description
The H34063AP Series is a monolithic control circuit containing the
primary functions required for DC-to-DC converters. These devices
consist of an internal temperature compensated reference,
comparator, controlled duty cycle oscillator with an active current
limit circuit, driver and high current output switch. This series was
specifically by Hi-Sincerity Microelectronics Corp.
Features
• 3V to 40V Input Voltage Operation
• Internal 1.6A Peak Current Switch
• Internal ±1.8% Reference
• Low Quiescent Current at 1.6mA
• Frequency Operation from 100Hz~100KHz
• Current Limiting
Applications
• Saver for Cellular Phone
• DC-DC Converter Module
Typical Application Circuit
Fig1.Saver Circuit for Cellular Phone
L1
Vout
200µH
H34063AP
8
1
2
3
4
RSC
D1
Cout
7
6
5
H1N5819
220µF
Vin
CT
470ρF
RB
C1
100µF
33kΩ
RA
5.6kΩ
HSMC Product Specification
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 2/6
HI-SINCERITY
MICROELECTRONICS CORP.
Pin Connections
8
7
6
5
Pin1:Switch Collector
Pin2:Switch Emitter
Pin3:Timing Capacitor
Pin4:Gnd
Pin5:Comparator Inverting Input
Pin6:Vcc
Pin7:Ipk Sense
1
2
3
4
Pin8:Driver Collector
Absolute Maxium Rating
Supply Voltage ..................................................................................................................... 40 V
Comparator Input Voltage Range ............................................................................. -0.3V ~ 40 V
Switch Collector Voltage ...................................................................................................... 40 V
Switch Emitter Voltage ......................................................................................................... 40 V
Switch Collector to Emitter Voltage ...................................................................................... 40 V
Driver Collector Voltage ....................................................................................................... 40 V
Switch Current ..................................................................................................................... 1.6 A
Power Dissipation DIP Package Ta=25°C .......................................................................... 1.0 W
Thermal Resistance Junction To Air............................................................................ 125 °C / W
Operating Junction Temperature........................................................................................ 125 °C
Operating Ambient Temperature Range ........................................................................ 0 ~ 70 °C
Storage Temperature Range................................................................................ -40 °C ~ 125 °C
(Vcc=5V,Ta=25°C, unless otherwise specified)
Electrical Characteristics
Parameter
Test Condition
Symbol
Min. Typ. Max. Unit
Oscillator
Charging Current
Discharge Current
Voltage Amplitude
Discharge to Charge Current Ratio VIPK(Sense) =VCC
Current Limit Sense Voltage
Ichg
Idischg
VOSC
IDischg/Ichg
VIPK(Sence)
24
35
42
uA
uA
V
5.0V≤VCC≤40V
5.0V≤VCC≤40V
Pin3
140 220 260
-
5.2
0.6
6.5
-
7.5
IChg=Idischg
250 300 350 mV
Output Switch
Saturation Voltage, Darlington
Connection
ISW=1.0A,
VC(Driver)=VC(Switch)
ISW=1.0A,
IC(Driver)=50mA
(Forced β ≈ 20)
ISW=1.0A, VCE=5.0V
VCE=30V
VCE(Sat)
VCE(Sat)
-
-
1.0
1.3
V
V
Saturation Voltage
0.4
75
0.7
-
DC Current Gain
Collector Off-State Current
hFE
ICC(Off)
50
-
V
UA
0.01 100
Comparator
Threshold Voltage
Threshold Voltage
1.227 1.250 1.273
VFB
V
0°C≤Ta≤70°C
1.210
-
1.29
Threshold Voltage Line Regulation
Input Bias Current
Regline
IIB
-
-
1.5
6
mV
3.0V≤VCC≤40V
VIN=0V
-20 -400 nA
VIPK(Sence)=VCC
VPin5>VFB,
Supply Current
ICC
-
1.6
3
mA
5.0V≤VCC≤40V
CT=0.0001uF,Pin2=Gnd
Remaining pins open
HSMC Product Specification
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 3/6
HI-SINCERITY
MICROELECTRONICS CORP.
Block Diagram
DRI
SC
Pin8:Driver Collector
Pin1:1.6A Switch Collector
Q2
Q S
R
Q1
80Ω
IPK
Pin7:Highside Current Sense
Input, VCC-VIPK=300mV
SE
IPK
Oscillator
Comparator
Pin2:Darlington Switch Emitter
CT
VCC
TC
Pin6:Power Supply Input
Pin3:Oscilletor Timing Capacitor
+
1.25V
-
Reference Voltage
GND
FB
Pin4:Power GND
Pin5:Feedback Comparator
Inverting Input
Application Information
Design Formula Table
Calculation
Step-Down
Step-Up
Voltage-Inverting
Vout+VF /
Vin(min) -Vsat-VOut
Vout+VF-Vin(min) /
Vin(min)-Vsat
|Vout| + VF /
Vin-Vsat
ton / toff
(ton + toff) max
1/Fmin
4*10-5ton
1/Fmin
4*10-5ton
1/Fmin
4*10-5ton
CT
IC(switch)
RS
2*Iout(max)
0.3 / IC(switch)
2*Iout(max)(ton+toff/toff)
0.3 / IC(switch)
2*Iout(max)(ton+toff/toff)
0.3 / IC(switch)
(Vin(min)-Vsat-Vout / IC(switch))
*ton(max)
(Vin(min)-Vsat / IC(switch))
*ton(max)
(Vin(min)-Vsat/ IC(switch))
*ton(max)
L(min)
CO
IC(switch)*(ton+toff) /
8VRipple(P-P)
Iout*ton / VRipple(P-P)
Iout*ton / VRipple(P-P)
Vsat : Saturation voltage of the output switch.
VF : Forward voltage drop of the ringback rectifier.
The following power supply characteristics must be chosen :
Vin : Nominal input voltage.
Vout : Desired output voltage. |Vout|=1.25*(1+RB/RA)
Iout- Desired output current
Fmin : Minimum desired output switching frequency at the selected values for Vin and Iout.
VRipple(P-P) : Desired peak to peak output ripple voltage in practice, the calculated value will need to be increased
due to the capacitor equivalent series resistance and board layout. The ripple voltage should be kept to a low value
since it will directly effect the line and load regulation.
HSMC Product Specification
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 4/6
HI-SINCERITY
MICROELECTRONICS CORP.
(Continuos)
Application Information
Fig.2 Step-Up Converter
D1
L1
Vout
28V / 200mA
200µH
R1
150Ω
H34063AP
Cout
220µF
8
7
6
1
2
3
4
RSC
0.22
Vin
C1
CT
680ρF
5
100µF
RB
47kΩ
RA
2.2kΩ
Line Regulation : 100mV (Vin=8V~16V, @Io=200mA)
Load Regulation : 5mV (Vin=12V, @Io=80mA~200mA)
Fig.3 Step-Up Converter With External NPN Switch
L1
Vout
R1
D1
H34063AP
8
7
6
1
2
3
4
RSC
Vin
Cout
Q1
R2
C1
CT
5
RB
RA
Fig.4 Step-Down Converter
L1
Vout
5V / 500mA
H34063AP
8
1
2
3
4
RSC
0.25
Cout
470µF
7
6
5
D1
H1N5819
Vin
CT
470ρF
C1
100µF
RB
3.6kΩ
RA
1.2kΩ
Line Regulation : 40mV (Vin=10V~20V, @Io=500mA)
Load Regulation : 5mV (Vin=15V, @Io=10mA~500mA)
Short Circuit Current : 1.3A (Vin=15V, @RL=0.1Ω
HSMC Product Specification
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 5/6
HI-SINCERITY
MICROELECTRONICS CORP.
Fig.5 Step-Down Converter With External PNP Saturation Switch
H34063AP
R1
R2
8
7
6
1
2
3
4
Q1
RSC
C1
L1
Vout
Cout
Vin
CT
D1
5
RB
RA
Fig.6 Voltage Inverting Converter
Vout
-12V / 100mA
H34063AP
D1 H1N5819
8
7
6
RSC
0.25
1
2
3
4
L1
100µH
Cout
470µF
Vin
4.5V-6V
CT
680ρF
5
C1
100µF
RA
953Ω
RB
8.2kΩ
Line Regulation : 20mV (Vin=4.5V~6V, @Io=100mA)
Load Regulation : 100mV (Vin=5V, @Io=10mA~100mA)
Fig.7 Voltage Inverting Converter With External PNP Saturation Switch
H34063AP
R2
R1
Q1
L1
8
7
6
1
2
3
4
RSC
Vin
D1
5
CT
RA
Vout
C1
Cout
RB
HSMC Product Specification
Spec. No. : Preliminary Data
Issued Date : 1998.08.01
Revised Date : 1999.06.01
Page No. : 6/6
HI-SINCERITY
MICROELECTRONICS CORP.
DIP-8P Dimension
Marking :
6
3
5
4
8 7
Package Code
HSMC Logo
Part Number
Date Code
A
2
1
Ink Mark
B
J
DIP-8P Plastic Package
HSMC Package Code : P
F
α
1
K
L
E
C
G
D H
M
I
*:Typical
Inches
Millimeters
Inches
Min. Max.
0.0150 0.0210
0.0898 0.1098
0.2950 0.3050
Millimeters
DIM
DIM
Min.
Max.
Min.
Max.
6.40
9.32
*1.52
*1.27
*0.99
3.35
3.55
Min.
0.38
2.28
7.49
-
Max.
0.53
2.79
7.74
*3.00
8.81
0.381
97°
A
B
C
D
E
F
0.2480 0.2520
0.3630 0.3670
6.29
9.22
-
H
I
J
K
L
M
-
-
-
*0.0600
*0.0500
*0.0390
-
-
-
*0.1181
0.3370 0.7470
0.0090 0.0150
8.56
0.229
94°
0.1280 0.1320
0.1250 0.1400
3.25
3.17
G
α1
94°
97°
Notes : 1.Dimension and tolerance based on our Spec. dated Sep. 07,1997.
2.Controlling dimension : millimeters.
3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material.
4.If there is any question with packing specification or packing method, please contact your local HSMC sales office.
Material :
• Lead : 42 Alloy ; solder plating
• Mold Compound : Epoxy resin family, flammability solid burning class:UL94V-0
Important Notice :
• All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC.
• HSMC reserves the right to make changes to its products without notice.
• HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems.
• HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance.
Head Office And Factory :
• Head Office (Hi-Sincerity Microelectronics Corp.) : 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C.
Tel : 886-2-25212056 Fax : 886-2-25632712, 25368454
• Factory 1 : No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C
Tel : 886-3-5983621~5 Fax : 886-3-5982931
• Factory 2 : No. 17-1, Ta-Tung Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C
Tel : 886-3-5977061 Fax : 886-3-5979220
HSMC Product Specification
相关型号:
©2020 ICPDF网 联系我们和版权申明