MK3233-01S [ICSI]
Handheld System Clock Synthesizer; 手持系统时钟合成器型号: | MK3233-01S |
厂家: | INTEGRATED CIRCUIT SOLUTION INC |
描述: | Handheld System Clock Synthesizer |
文件: | 总4页 (文件大小:72K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MK3233
Handheld System Clock Synthesizer
ICR O CLOC K
Description
Features
• Input crystal frequency of 32.768 kHz
• Lowest power solution available
The MK3233 is the smallest size, lowest power system
clock synthesizer available. It is the ideal way to
generate clocks for smart cell phones, PDAs, and other
devices where low power is required. Using analog
Phase-Locked Loop (PLL) techniques, the device
operates from a single 32.768 kHz crystal to produce
the 32.768 kHz, CPU, and serial communications
output clocks.
• Operating temperature of -20 to 70 °C
• Output clock frequencies up to 50 MHz
• Three output clocks
• 3.3 V or 5.0 V operation
The device has multiple power down modes for the
CPU, communications, and 32.768 kHz clocks.
• Duty cycle of 45/55
• Eight selectable CPU frequencies
• CPU or Communication clock power down
• Separate battery supply pin for 32 kHz runs to 2V
• IDD less than 4µA when 32 kHz running
• Serial port clocks of 1.8432 MHz (-01 version) or
3.6864 MHz (-02 version)
The MK3233 can save board space and cost even if it
only replaces the 32 kHz oscillator circuitry and one
additional surface mount crystal or oscillator. The
extremely low IDD, the ease of surface mounting, the
upgradeability of CPU frequencies, and the power
down capability are added benefits in using the part.
• Packaged in 16 pin narrow SOIC
Block Diagram
VDD GND
CPUS0
CPUS1
CPUS2
CPU
Output
Buffer
Clock Synthesis
and Control
Circuitry
CPUCLK
PDCPU
PDCOMM
PD
Communications
Clock Synthesis
and Control
Output
Buffer
1.843 or
3.686 MHz
VDD32
Circuitry
32.768 kHz
crystal
or
X1
Crystal
Oscillator
clock
Output
Buffer
32.768 kHz
X2
MDS 3233 F
1
Revision 11070
Printed 11/16/00
Integrated Circuit Systems, Inc.• 525 Race Street• San Jose • CA • 95126• (408) 295-9800 tel • www.icst.com
MK3233
Handheld System Clock Synthesizer
ICR O CLOC K
Pin Assignment
CPU Clock Decoding
CPUS2 CPUS1 CPUS0 CPUCLK (MHz)
1
CPUS2
16 CPUS1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
8.00
15
14
13
12
11
10
9
2
3
CPUS0
X2
X1
13.00
16.00
20.00
40.00
25.00
50.00
33.33
CPUCLK
VDD32
VDD
GND
4
5
VDD
GND
PD
6
7
COMMCLK
32K
PDCPU
Frequency transitions will occur smoothly.
8
PDCOMM
Pin Descriptions
Number
Name
CPUS2
X2
Type Description
1
2
I
O
I
Select 2 for CPUCLK frequencies. See Table above.
Crystal connection. Connect to 32.768 kHz crystal.
3
X1
Crystal connection. Connect to 32.768 kHz crystal.
Separate power supply connection for 32.768 kHz clock. Will operate to 2.0 V.
Connect to +3.3 V or +5 V. Must be the same voltage as pin 13.
Connect to ground.
4
VDD32
VDD
P
P
P
O
O
I
5
6
GND
7
COMMCLK
32K
Serial communications (1.84 on -01 version, or 3.68MHz on -02 version) clock output.
32.768 kHz square wave clock output.
8
9
PDCOMM
PDCPU
PD
Power Down serial Communications clock output (stops low) when low.
Power Down CPU clock output (stops low) when low.
Powers Down everything but 32 kHz oscillator internally. 32 kHz output buffer is off.
Connect to ground.
10
11
12
13
14
15
16
I
I
GND
P
P
O
I
VDD
Connect to +3.3 V or +5 V. Must be the same voltage as pin 5.
CPUCLK output. See Table above.
CPUCLK
CPUS0
CPUS1
Select 0 for CPUCLK frequencies. See Table above.
Select 1 for CPUCLK frequencies. See Table above.
I
Type: I = Input, O = output, P = power supply connection
Power Down status: Output clocks will stop in a low state when powered down
External Components
The MK3233 requires a minimum number of external components for proper operation. Decoupling
capacitors of 0.1µF should be connected between VDD and GND, and VDD32 and GND, as close to the
MK3233 as possible. A series resistor should be used on the VDD32 supply. A series termination resistor of
33Wmay be used for each clock output, except the 32.768 kHz. For tuning the real time clock output, use
a 32.768 kHz crystal with a load capacitance of 12.5pF, and connect a 20pF±5% (NPO dielectric)
capacitor between each crystal pin and ground. The 32.768 kHz crystal must be connected as close to the
chip as possible. Consult MicroClock for a recommended external circuit schematic.
MDS 3233 F
2
Revision 11070
Printed 11/16/00
Integrated Circuit Systems, Inc.• 525 Race Street• San Jose • CA • 95126• (408) 295-9800 tel • www.icst.com
MK3233
Handheld System Clock Synthesizer
ICR O CLOC K
Electrical Specifications
Parameter
Conditions
Minimum
Typical
Maximum
Units
ABSOLUTE MAXIMUM RATINGS (note 1)
Supply Voltage, VDD
Referenced to GND
7
VDD+0.5
70
V
V
Inputs and Clock Outputs
Ambient Operating Temperature
Soldering Temperature
Storage Temperature
Referenced to GND
Max of 10 seconds
-0.5
-20
°C
°C
°C
260
-65
150
DC CHARACTERISTICS (at 5.0 V unless otherwise noted)
Operating Voltage, VDD
3.0
2.0
2.0
5.5
5.5
V
V
Operating Voltage, VDD32
Input High Voltage, VIH
VDD=5 V
V
Input Low Voltage, VIL
VDD=5 V
0.8
0.4
0.4
0.4
V
Output High Voltage, VOH
Output Low Voltage, VOL
Input High Voltage, VIH
VDD=5 V, IOH=-25mA
VDD=5 V, IOL=25mA
VDD=3.3 V
2.4
1.9
2.4
V
V
V
Input Low Voltage, VIL
VDD=3.3 V
V
Output High Voltage, VOH
Output Low Voltage, VOL
IDD Operating Supply Current, 5 V
IDD32 with only 32 kHz running, 5 V
IDD Operating Supply Current, 3.3 V
VDD=3.3 V, IOH=-8mA
VDD=3.3 V, IOL=8mA
No Load, 50MHz
No Load
V
V
11
3.5
6.5
2.5
1
mA
µA
mA
µA
µA
mA
mA
pF
No Load, 50MHz
IDD32 with only 32 kHz output running, 3.3 V No Load
IDD32, only 32 kHz osc. running, 3.3 V, note 2 32kHz output off. PD=0
Short Circuit Current, 5 V
Short Circuit Current, 5 V
Input Capacitance
32 kHz output
CPU output
±30
±100
7
AC CHARACTERISTICS (at 5.0 V unless otherwise noted)
Input Frequency
32.768
kHz
ns
Output Clock Rise and Fall Time, 0.2 to 0.8VDD
2
Output Clock Duty Cycle, all MHz clocks
32.768 kHz Clock Duty Cycle
At VDD/2
45
49 to 51
57
55
%
At VDD32/2
20 to 50 MHz
%
Absolute Clock Period Jitter, CPU clock
-500
500
ps
Power up time, CPU off to 50 MHz, 32k running VDD=3.3 or 5 V
9
4
ms
ms
ms
ms
ms
Transition time, 8 MHz to 50 MHz
VDD=3.3 or 5 V
VDD=3.3 or 5 V
Transition time, 50 MHz to 8 MHz
2.5
500
15
Power on time,VDD32=0 V to all clocks stable
Power on time, all power down pins taken high
32.768kHz crystal with ESR £25kW
1000
32.768kHz oscillator running
Note 1: Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged
exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability.
Note 2: When PD=0 (low) and VDD32 is greater than 2.0V, then the 32kHz oscillator will continue to run on the chip, but the
output is turned off. This allows for a quick power-up (<20ms), while the chip is only consuming approximately 1µA.
MDS 3233 F
3
Revision 11070
Printed 11/16/00
Integrated Circuit Systems, Inc.• 525 Race Street• San Jose • CA • 95126• (408) 295-9800 tel • www.icst.com
MK3233
Handheld System Clock Synthesizer
ICR O CLOC K
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC Publication No. 95.)
16 pin SOIC narrow
Inches
Min
Millimeters
Symbol
A
Max
Min
1.35
0.10
0.33
0.19
9.80
3.80
1.27 BSC
5.80
0.25
0.41
Max
0.0532 0.0688
0.0040 0.0098
0.0130 0.0200
0.0075 0.0098
0.3859 0.3937
0.1497 0.1574
.050 BSC
1.75
0.24
0.51
0.24
10.00
4.00
A1
E
H
B
C
INDEX
AREA
D
E
e
H
h
0.2284 0.2440
0.0099 0.0195
0.0160 0.0500
6.20
0.50
1.27
h x 45°
D
L
A
A1
C
B
e
L
Ordering Information
Part/Order Number
Marking
Communications Clock
Package
Temperature
MK3233-01S
MK3233-02S
MK3233-01S
MK3233-02S
MK3233-01S
MK3233-02S
1.843 MHz
3.686 MHz
1.843 MHz
3.686 MHz
16 pin SOIC
16 pin SOIC
-20 to 70 °C
-20 to 70 °C
MK3233-01STR
MK3233-02STR
Add Tape & Reel -20 to 70 °C
Add Tape & Reel -20 to 70 °C
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its
use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is
intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does
not authorize or warrant any ICS product for use in life support devices or critical medical instruments.
MDS 3233 F
4
Revision 11070
Printed 11/16/00
Integrated Circuit Systems, Inc.• 525 Race Street• San Jose • CA • 95126• (408) 295-9800 tel • www.icst.com
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明