7005L17GGB8 [IDT]
HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM;型号: | 7005L17GGB8 |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | HIGH-SPEED 8K x 8 DUAL-PORT STATIC RAM |
文件: | 总21页 (文件大小:733K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HIGH-SPEED
IDT7005S/L
8K x 8 DUAL-PORT
STATIC RAM
Features
◆
◆
True Dual-Ported memory cells which allow simultaneous
reads of the same memory location
High-speed access
M/S = H for BUSY output flag on Master,
M/S = L for BUSY input on Slave
Interrupt Flag
◆
◆
◆
◆
– Military:20/25/35/55/70ns(max.)
– Industrial:20/35/55ns(max.)
– Commercial:15/17/20/25/35/55ns(max.)
Low-power operation
On-chip port arbitration logic
Full on-chip hardware support of semaphore signaling
between ports
◆
◆
◆
Fully asynchronous operation from either port
Devices are capable of withstanding greater than 2001V
electrostatic discharge
– IDT7005S
Active:750mW(typ.)
◆
◆
◆
Standby: 5mW (typ.)
Battery backup operation—2V data retention
TTL-compatible, single 5V (±10%) power supply
Available in 68-pin PGA, PLCC and a 64-pin thin quad
flatpack
– IDT7005L
Active:700mW(typ.)
Standby: 1mW (typ.)
◆
◆
◆
IDT7005 easily expands data bus width to 16 bits or more
using the Master/Slave select when cascading more than
one device
Industrial temperature range (-40°C to +85°C) is available for
selectedspeeds
Green parts available, see ordering information
FunctionalBlockDiagram
OER
OEL
CEL
CER
R/W
L
R/WR
I/O0L- I/O7L
I/O0R-I/O7R
I/O
I/O
Control
Control
BUSY (1,2)
L
(1,2)
BUSY
R
A
12R
0R
A
12L
Address
Decoder
MEMORY
ARRAY
Address
Decoder
A
0L
A
13
13
ARBITRATION
INTERRUPT
SEMAPHORE
LOGIC
CE
OE
L
L
CE
OE
R/W
R
R
R
R/W
L
SEM
R
SEM
L
M/S
(2)
(2)
INTR
INTL
2738 drw 01
NOTES:
1. (MASTER): BUSY is output; (SLAVE): BUSY is input.
2. BUSY outputs and INT outputs are non-tri-stated push-pull.
JUNE 2016
1
DSC 2738/18
©2016 Integrated Device Technology, Inc.
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Description
The IDT7005 is a high-speed 8K x 8 Dual-Port Static RAM. The
IDT7005isdesignedtobeusedasastand-alone64K-bitDual-PortRAM
or as a combination MASTER/SLAVE Dual-Port RAM for 16-bit-or-
more word systems. Using the IDT MASTER/SLAVE Dual-Port RAM
approach in 16-bit or wider memory system applications results in full-
speed,error-freeoperationwithouttheneedforadditionaldiscretelogic.
This device provides two independent ports with separate control,
address,andI/Opinsthatpermitindependent,asynchronousaccessfor
reads or writes to any location in memory. An automatic power down
featurecontrolledbyCEpermitstheon-chipcircuitryofeachporttoenter
a very low standby power mode.
Fabricated using CMOS high-performance technology, these de-
vicestypicallyoperateononly750mWofpower.Low-power(L)versions
offerbatterybackupdataretentioncapabilitywithtypicalpowerconsump-
tionof500µWfroma2Vbattery.
The IDT7005 is packaged in a ceramic 68-pin PGA, 68-pin PLCC
and a 64-pin thin quad flatpack, (TQFP). Military grade product is
manufacturedincompliancewithMIL-PRF-38535QMLmakingitideally
suitedtomilitarytemperatureapplicationsdemandingthehighestlevelof
performanceandreliability.
PinConfigurations(1,2,3)
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
I/O7R
N/C
27
9
8
I/O1L
I/O0L
N/C
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
OE
R/W
SEM
CE
R
R
R
R
7
6
OE
R/W
SEM
CE
L
5
L
4
L
N/C
N/C
GND
3
L
2
7005J
J68(4)
N/C
N/C
1
A12R
A11R
A10R
68
67
66
65
64
63
62
61
VCC
A
A
A
A
A
A
12L
11L
10L
9L
A
A
A
A
A
9R
8R
7R
6R
5R
8L
7L
A6L
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
2738 drw 02
44
46 45
43 42 41 40 39 38 37 36 35 34 33
32
47
48
49
A
5L
6L
A
5R
6R
A
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
31
30
29
28
27
26
A
A
7L
8L
9L
A
7R
8R
9R
A
A
A
A
A10L
A10R
A11R
A12R
A
A
11L
12L
7005
PN64(4)
25
VCC
24
GND
N/C
N/C
23
22
21
20
19
18
17
CE
SEM
R/W
L
L
L
CE
SEM
R/W
OE
R
R
R
OE
L
R
NOTES:
I/O0L
I/O1L
I/O7R
I/O6R
1. All VCC pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. J68packagebodyisapproximately.95inx.95inx.12in.
PN64packagebodyisapproximately14mmx14mmx1.4mm.
4. Thispackagecodeisusedtoreferencethepackagediagram.
9
7 8
1
2
3
4
5
6
10 11 12 13 14 15 16
2738 drw 03
6.242
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Pin Configurations(1,2,3) (con't.)
51
A
50
48
A
46
A
44
0L BUSY
42
M/S
40
INT
38
36
11
10
09
08
07
5L
A4L
2L
1L
L
R
A
1R
A3R
53
A
52
49
47
A
45
INT
43
GND
41
BUSYR
39
37
35
34
L
A4R
7L
9L
A3L
A
0R
A
2R
A
5R
6R
8R
A
6L
8L
55
A
54
32
33
A
A7R
A
57
A
56
30
31
A
A9R
A10L
11L
59
58
A
28
29
A10R
12L
A11R
V
CC
7005G
(4,5)
61
60
26
27
G68
06
05
04
03
02
01
N/C
GND
A
12R
N/C
63
SEM
62
24
N/C
25
N/C
L
CEL
65
64
22
23
SEM
R
CE
21
R
OEL
R/W
66
L
67
I/O0L
20
R/W
R
OE
R
N/C
1
3
5
7
9
68
I/O1L
11
I/O1R
13
V
15
18
I/O7R
19
N/C
I/O2L
GND
CC I/O4R
I/O4L GND I/O7L
2
4
6
8
10
12
14
16
17
I/O3L
I/O6L
I/O5L
VCC I/O0R I/O2R I/O3R I/O5R I/O6R
A
B
C
D
E
F
G
H
J
K
L
INDEX
2738 drw 04
NOTES:
1. All VCC pins must be connected to power supply.
2. All GND pins must be connected to ground supply.
3. Package body is approximately 1.18in x 1.18in x .16in.
PinNames
Left Port
Right Port
Names
4. This package code is used to reference the package diagram.
5. This text does not indicate oriention of the actual part-marking
Chip Enable
CE
R/W
OE
L
CE
R/W
OE
R
L
R
Read/Write Enable
Output Enable
Address
L
R
A
0L - A12L
A
0R - A12R
I/O0R - I/O7R
SEM
INT
BUSY
M/S
I/O0L - I/O7L
SEM
INT
BUSY
Data Input/Output
Semaphore Enable
Interrupt Flag
Busy Flag
L
R
L
R
L
R
Master or Slave Select
Power
V
CC
GND
Ground
2738 tbl 01
6.42
3
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Truth Table I: Non-Contention Read/Write Control
Inputs(1)
R/W
Outputs
I/O0-7
Mode
CE
H
L
OE
X
SEM
H
X
L
High-Z
DATAIN
Deselected: Power-Down
Write to Memory
X
H
L
H
X
L
H
DATAOUT Read Memory
High-Z Outputs Disabled
X
H
X
2738 tbl 02
NOTE:
1. A0L – A12L is not equal to A0R – A12R
Truth Table II: Semaphore Read/Write Control(1)
Inputs(1)
R/W
Outputs
I/O0-7
Mode
CE
H
OE
L
SEM
H
↑
X
L
L
L
DATAOUT Read in Semaphore Flag Data Out
H
X
DATAIN
____
Write I/Oo into Semaphore Flag
Not Allowed
L
X
2738 tbl 03
NOTE:
1. There are eight semaphore flags written to via I/O0 and read from I/O0 - I/O7. These eight semaphores are addressed by A0 - A2.
AbsoluteMaximumRatings(1)
MaximumOperatingTemperature
andSupplyVoltage(1,2)
Commercial
& Industrial
Symbol
Rating
Military
Unit
Ambient
(2)
Grade
Temperature
-55OC to+125OC
0OC to +70OC
-40OC to +85OC
GND
0V
Vcc
V
TERM
Terminal Voltage
with Respect to
GND
-0.5 to +7.0
-0.5 to +7.0
V
Military
5.0V
5.0V
5.0V
+
+
+
10%
10%
10%
Temperature Under
Bias
-55 to +125
-65 to +150
50
-65 to +135
-65 to +150
50
oC
oC
Commercial
Industrial
0V
T
BIAS
OV
TSTG
Storage
2738 tbl 05
Te m p e rature
NOTES:
1. This is the parameter TA. This is the "instant on" case temperature.
mA
IOUT
DC Output Current
2
Industrial temperature: for specific speeds, packages and powers contact
your sales office.
2738 tbl 04
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS
maycausepermanentdamagetothedevice.Thisisastressratingonlyandfunctional
operation of the device at these or any other conditions above
thoseindicatedintheoperationalsectionsofthisspecificationisnotimplied.Exposureto
absolutemaximumratingconditionsforextendedperiodsmayaffectreliability.
2. VTERMmustnotexceedVcc+10%formorethan25%ofthecycletimeor10%maximum,
andislimitedto<20mAfortheperiodofVTERM>Vcc+10%.
RecommendedDCOperating
Conditions
Symbol
Parameter
Supply Voltage
Min.
4.5
Typ.
Max. Unit
V
CC
5.0
5.5
V
V
V
GND
Ground
0
0
0
Capacitance(1) (TA = +25°C, f = 1.0MHz)
V
IH
Input High Voltage
Input Low Voltage
2.2
-0.5(1)
6.0(2)
0.8
____
Symbol
Parameter
Input Capacitance
Output Capacitance
Conditions(2)
Max.
9
Unit
____
V
IL
V
CIN
V
IN = 3dV
pF
2738 tbl 06
NOTES:
1. VIL > -1.5V for pulse width less than 10ns.
2. VTERM must not exceed Vcc + 10%.
COUT
V
OUT = 3dV
10
pF
2738 tbl 07
NOTES:
1. Theseparametersaredeterminedbydevicecharacterizationbutarenotproductiontested
(TQFPPackageonly).
2. 3dVreferencestheinterpolatedcapacitancewhentheinputandoutputsignalsswitchfrom
0Vto3Vorfrom3Vto0V.
6.442
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the 0perating
Temperature and Supply Voltage Range (VCC = 5.0V ± 10%)
7005S
7005L
Symbol
|ILI|
Parameter
Input Leakage Current(1)
Output Leakage Current
Output Low Voltage
Test Conditions
VCC = 5.5V, VIN = 0V to VCC
CE = VIH, VOUT = 0V to VCC
IOL = +4mA
Min.
___
Max.
10
Min.
___
Max.
Unit
µA
µA
V
5
5
___
___
___
___
|ILO|
10
VOL
0.4
0.4
___
___
VOH
Output High Voltage
IOH = -4mA
2.4
2.4
V
2738 tbl 08
NOTE:
1. At Vcc < 2.0V input leakages are undefined.
Data Retention Characteristics Over All Temperature Ranges
(L Version Only) (VLC = 0.2V, VHC = VCC - 0.2V)
Symbol
Parameter
Test Condition
Min.
Typ.(1)
___
Max.
___
Unit
V
V
DR
V
CC for Data Retention
V
CC = 2V
CE > VHC
IN > VHC or < VLC
SEM > VHC
2.0
___
ICCDR
Data Retention Current
Mil. & Ind.
Com'l.
100
4000
µA
___
V
100
___
1500
___
(3)
tCDR
Chip Deselect to Data Retention Time
Operation Recovery Time
0
ns
(3)
(2)
___
___
tR
tRC
ns
2738 tbl 09
NOTES:
1. TA = +25°C, VCC = 2V, and are not production tested.
2. tRC = Read Cycle Time
3. This parameter is guaranteed by characterization, but is not production tested.
Data Retention Waveform
DATA RETENTION MODE
VDR >
4.5V
4.5V
VCC
2V
tCDR
tR
VDR
CE
VIH
VIH
2738 drw 05
6.42
5
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range(1) (VCC = 5.0V ± 10%)
7005X15
7005X17
7005X20
Com'l, Ind
& Military
7005X25
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Test Condition
Version
COM'L
Typ.(2)
Max.
Typ.(2)
Max.
Typ.(2)
Max.
Typ.(2)
Max.
Unit
ICC
Dynamic Operating Current
(Both Ports Active)
S
L
170
310
170
310
160
150
290
240
155
145
265
220
mA
CE = VIL, Outputs Disabled
SEM = VIH
160
260
160
260
(3)
f = fMAX
____
____
____
____
____
____
____
____
MIL &
IND
S
L
160
150
370
320
155
145
340
280
I
SB1
Standby Current
(Both Ports - TTL
Level Inputs)
COM'L
S
L
20
10
____
____
60
60
____
____
20
10
____
____
60
50
____
____
20
10
60
50
16
10
60
50
mA
mA
CE
L
= CE
(3)
R
= VIH
SEM
R
= SEM
L
= VIH
f = fMAX
MIL &
IND
S
L
20
10
90
70
16
10
80
65
(5)
ISB2
Standby Current
(One Port - TTL
Level Inputs)
COM'L
S
L
105
95
____
____
190
160
105
95
____
____
190
160
95
85
180
150
90
80
170
140
CE"A" = VIL and CE"B" = VIH
Active(3P) ort Outputs Disabled
f=fMAX
____
____
____
____
MIL &
IND
S
L
95
85
240
210
90
80
215
180
SEM
R
= SEM
L
= VIH
I
SB3
Full Standby Current (Both
Ports - All CMOS Level
Inputs)
Both Ports CE
L
and
COM'L
S
L
1.0
0.2
____
____
15
5
____
____
1.0
0.2
____
____
15
5
____
____
1.0
0.2
15
5
1.0
0.2
15
5
mA
mA
CE
R
> VCC - 0.2V
V
V
IN > VCC - 0.2V or
IN < 0.2V, f = 0(4)
MIL &
IND
S
L
1.0
0.2
30
10
1.0
0.2
30
10
SEM
R
= SEM
L
> VCC - 0.2V
ISB4
Full Standby Current
(One Port - All
COM'L
S
L
100
90
170
140
100
90
170
140
90
80
155
130
85
75
145
120
CE"A" < 0.2V and
CE"B" > VCC - 0.2V(5)
CMOS Level Inputs)
SEMR = SEML > VCC - 0.2V
____
____
____
____
____
____
____
____
MIL &
IND
S
L
90
80
225
200
85
75
200
170
V
IN > VCC - 0.2V or VIN < 0.2V
Active Port Outputs Disabled
(3)
f = fMAX
2738 tbl 10
7005X35
7005X55
7005X70
Com'l, Ind
& Military
Com'l, Ind
& Military
Military
Only
Symbol
Parameter
Test Condition
Version
Typ.(2)
Max.
Typ.(2)
Max.
Typ.(2)
Max.
Unit
____
____
____
____
ICC
Dynamic Operating
Current
COM'L
S
L
150
140
250
210
150
140
250
210
mA
CE = VIL, Outputs Disabled
SEM = VIH
(3)
(Both Ports Active)
f = fMAX
MIL &
IND
S
L
150
140
300
250
150
140
300
250
140
130
300
250
____
____
____
____
I
SB1
Standby Current
(Both Ports - TTL
Level Inputs)
COM'L
S
L
13
10
60
50
13
10
60
50
mA
mA
CE
SEM
f = fMAX
L
= CE
(3)
R
= VIH
= VIH
R
= SEM
L
MIL &
IND
S
L
13
10
80
65
13
10
80
65
10
8
____
____
80
65
____
____
(5)
ISB2
Standby Current
(One Port - TTL
Level Inputs)
COM'L
S
L
85
75
155
130
85
75
155
130
CE"A" = VIL and CE"B" = VIH
Active(3P) ort Outputs Disabled
f=fMAX
85
75
MIL &
IND
S
L
190
160
85
75
190
160
80
70
190
160
SEMR
= SEM
L
= VIH
____
____
____
____
I
SB3
Full Standby Current
(Both Ports - All
Both Ports CE
L
and
COM'L
S
L
1.0
0.2
15
5
1.0
0.2
15
5
mA
mA
CER
> VCC - 0.2V
CMOS Level Inputs)
V
V
IN > VCC - 0.2V or
IN < 0.2V, f = 0(4)
= SEM > VCC - 0.2V
MIL &
IND
S
L
1.0
0.2
30
10
1.0
0.2
30
10
1.0
0.2
____
____
30
10
SEM
R
L
____
____
ISB4
Full Standby Current
(One Port - All
COM'L
S
L
80
70
135
110
80
70
135
110
CE"A" < 0.2V and
CE"B" > VCC - 0.2V(5)
CMOS Level Inputs)
SEMR = SEML > VCC - 0.2V
MIL &
IND
S
L
80
70
175
150
80
70
175
150
75
65
175
150
V
IN > VCC - 0.2V or VIN < 0.2V
Active Port Outputs Disabled
(3)
f = fMAX
2738 tbl 11
NOTES:
1. 'X' in part number indicates power rating (S or L)
2. VCC = 5V, TA = +25°C and are not production tested. ICC DC = 120mA (typ)
3. At f = fMAX, address and I/O'S are cycling at the maximum frequency read cycle of 1/tRC, and using “AC Test Conditions” of input levels of GND to 3V.
4. f = 0 means no address or control lines change.
5. Port "A" may be either left or right port. Port "B" is the port opposite port "A".
6.642
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
5V
5V
AC Test Conditions
Input Pulse Levels
Input Rise/Fall Times
Input Timing Reference Levels
Output Reference Levels
Output Load
GND to 3.0V
5ns Max.
1.5V
1.5V
Figures 1 and 2
1250Ω
1250Ω
DATAOUT
BUSY
INT
DATAOUT
5pF*
775Ω
30pF
775Ω
2738 tbl 12
2738 drw 06
Figure 1. AC Output Test Load
Figure 2. Output Test Load
(For tLZ, tHZ, tWZ, tOW)
*Including scope and jig
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(4)
7005X15
7005X17
7005X20
7005X25
Com'l &
Military
Com'l Only
Com'l Only
Com'l, Ind
& Military
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
READ CYCLE
____
____
____
____
t
RC
AA
ACE
AOE
OH
LZ
HZ
PU
PD
SOP
SAA
Read Cycle Time
15
____
17
____
20
____
25
____
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Address Access Time
Chip Enable Access Time(3)
Output Enable Access Time
15
15
17
17
20
20
25
25
____
____
____
____
____
____
____
____
t
t
10
____
10
____
12
____
13
____
t
Output Hold from Address Change
Output Low-Z Time(1,2)
Output High-Z Time(1,2)
Chip Enable to Power Up Time(2,5)
Chip Disable to Power Down Time(2,5)
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
3
3
3
3
____
____
____
____
t
3
____
3
____
3
____
3
____
t
10
____
10
____
12
____
15
____
t
0
____
0
____
0
____
0
____
t
15
____
17
____
20
____
25
____
t
10
____
10
____
10
____
10
____
t
15
17
20
25
ns
2738 tbl 13a
7005X35
7005X55
IDT7005X70
Military
Only
Com'l, Ind
& Military
Com'l, Ind
& Military
Symbol
READ CYCLE
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
____
____
____
t
RC
AA
ACE
AOE
OH
LZ
HZ
PU
PD
SOP
SAA
Read Cycle Time
35
____
55
____
70
____
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Address Access Time
35
35
55
55
70
70
Chip Enable Access Time(3)
Output Enable Access Time
Output Hold from Address Change
Output Low-Z Time(1,2)
Output High-Z Time(1,2)
Chip Enable to Power Up Time(2,5)
Chip Disable to Power Down Time(2,5)
____
____
____
____
____
____
t
t
20
____
30
____
35
____
t
3
3
3
____
____
____
t
3
____
3
____
3
____
t
15
____
25
____
30
____
t
0
____
0
____
0
____
t
35
____
50
____
50
____
t
Semaphore Flag Update Pulse (OE or SEM)
Semaphore Address Access Time
15
____
15
____
15
____
t
35
55
70
ns
2738 tbl 13b
NOTES:
1. Transition is measured 0mV from Low or High impedance voltage with load (Figures 1 and 2).
2. This parameter is guaranteed but not production tested.
3. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL.
4. 'X' in part number indicates power rating (S or L).
6.42
7
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Waveform of Read Cycles(5)
tRC
ADDR
(4)
t
t
AA
(4)
ACE
CE
OE
(4)
tAOE
R/W
(1)
LZ
tOH
t
VALID DATA(4)
DATAOUT
(2)
HZ
t
BUSYOUT
(3,4)
tBDD
2738 drw 07
NOTES:
1. Timing depends on which signal is asserted last, OE or CE.
2. Timing depends on which signal is de-asserted first CE or OE.
3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY
has no relation to valid output data.
4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD.
5. SEM = VIH.
Timing of Power-Up Power-Down
CE
tPU
tPD
ICC
ISB
,
2738 drw 08
6.842
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltage(5)
7005X15
7005X17
Com'l Only
7005X20
Com'l, Ind
& Military
7005X25
Com'l &
Military
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
WRITE CYCLE
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
WC
EW
AW
AS
WP
WR
DW
HZ
DH
WZ
OW
SWRD
SPS
Write Cycle Time
15
12
12
0
17
12
12
0
20
15
15
0
25
20
20
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
t
t
t
Write Pulse Width
12
0
12
0
15
0
20
0
t
Write Recovery Time
t
Data Valid to End-of-Write
Output High-Z Time(1,2)
Data Hold Time(4)
Write Enable to Output in High-Z(1,2)
Output Active from End-of-Write(1,2,4)
SEM Flag Write to Read Time
SEM Flag Contention Window
10
____
10
____
15
____
15
____
t
10
____
10
____
12
____
15
____
t
0
____
0
____
0
____
0
____
t
10
____
10
____
12
____
15
____
t
0
5
5
0
5
5
0
5
5
0
5
5
____
____
____
____
____
____
____
____
t
t
ns
2738 tbl 14a
7005X35
7005X55
7005X70
Military Only
Com'l, Ind
& Military
Com'l, Ind
& Military
Symbol
WRITE CYCLE
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
WC
EW
AW
AS
WP
WR
DW
HZ
DH
WZ
OW
SWRD
SPS
Write Cycle Time
35
30
30
0
55
45
45
0
70
50
50
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
t
Chip Enable to End-of-Write(3)
Address Valid to End-of-Write
Address Set-up Time(3)
Write Pulse Width
t
t
t
25
0
40
0
50
0
t
Write Recovery Time
Data Valid to End-of-Write
Output High-Z Time(1,2)
Data Hold Time(4)
t
15
____
30
____
40
____
t
15
____
25
____
30
____
t
0
____
0
____
0
____
(1,2)
t
Write Enable to Output in High-Z
15
____
25
____
30
____
t
Output Active from End-of-Write(1, 2,4)
SEM Flag Write to Read Time
SEM Flag Contention Window
0
5
5
0
5
5
0
5
5
____
____
____
____
____
____
t
t
ns
2738 tbl 14b
NOTES:
1. Transition is measured 0mV from Low or High-impedance voltage with load (Figure 2).
2. This parameter is guaranteed by device characterization but is not production tested.
3. To access RAM, CE = VIL, SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage
and temperature, the actual tDH will always be smaller than the actual tOW.
5. 'X' in part number indicates power rating (S or L).
6.42
9
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8)
tWC
ADDRESS
(7)
HZ
t
OE
tAW
CE or SEM(9)
(3)
WR
(6)
AS
(2)
tWP
t
t
R/W
DATAOUT
DATAIN
(7)
WZ
t
OW
t
(4)
(4)
t
DW
tDH
2738 drw 09
Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5)
tWC
ADDRESS
tAW
CE or SEM(9)
R/W
(6)
AS
(2)
EW
(3)
tWR
t
t
tDW
tDH
DATAIN
2738 drw 10
NOTES:
1. R/W or CE must be HIGH during all address transitions.
2. A write occurs during the overlap (tEW or tWP) of a LOW CE and a LOW R/W for memory array writing cycle.
3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle.
4. During this period, the I/O pins are in the output state and input signals must not be applied.
5. If the CE or SEM LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the High-impedance state.
6. Timing depends on which enable signal is asserted last, CE or R/W.
7. This parameter is guaranteed by device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure
2).
8. If OE is LOW during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be placed
on the bus for the required tDW. If OE is HIGH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified
tWP.
9. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition.
61.402
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Timing Waveform of Semaphore Read after Write Timing, Either Side(1)
tSAA
tOH
A0-A2
VALID ADDRESS
VALID ADDRESS
tAW
tWR
tACE
tEW
SEM
tDW
tSOP
OUT
VALID
DATA
DATA
0
DATAIN VALID
t
AS
tWP
tDH
R/W
tSWRD
tAOE
OE
tSOP
Write Cycle
Read Cycle
2738 drw 11
NOTE:
1. CE = VIH for the duration of the above timing (both write and read cycle).
Timing Waveform of Semaphore Write Contention(1,3,4)
A0"A"-A2"A"
MATCH
(2)
SIDE
“A”
R/W"A"
SEM"A"
tSPS
A0"B"-A2"B"
MATCH
(2)
R/W"B"
SEM"B"
SIDE “B”
2738 drw 12
NOTES:
1. DOR = DOL = VIL, CER = CEL = VIH. Semaphore flag is released from both sides (reads as ones from both sides) at cycle start.
2. All timing is the same for left and right ports. Port “A” may be either left or right port. “B” is the opposite from port “A”.
3. This parameter is measured from R/W“A” or SEM“A” going HIGH to R/W“B” or SEM“B” going HIGH.
4. If tSPS is not satisfied, the semaphore will fall positively to one side or the other, but there is no guarantee which side will obtain the flag.
6.42
11
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(6)
7005X15
7005X17
7005X20
Com'l, Ind
& Military
7005X25
Com'l &
Military
Com'l Only
Com'l Only
Symbol
BUSY TIMING (M/S=VIH
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max. Unit
)
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
t
BAA
BDA
BAC
BDC
APS
BDD
WH
15
15
15
17
17
17
20
20
20
20
20
20
ns
ns
ns
ns
ns
ns
ns
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Access Time from Chip Enable High
Arbitration Priority Set-up Time(2)
BUSY Disable to Valid Data(3)
Write Hold After BUSY(5)
t
t
t
15
____
17
____
17
____
17
____
t
5
____
5
____
5
____
5
____
t
18
____
18
____
30
____
30
____
t
12
13
15
17
BUSY TIMING (M/S=VIL
)
____
____
____
____
____
____
____
____
BUSY Input to Write(4)
Write Hold After BUSY(5)
t
WB
0
0
0
0
ns
ns
tWH
12
13
15
17
PORT-TO-PORT DELAY TIMING
____
____
____
____
____
____
____
____
t
WDD
Write Pulse to Data Delay(1)
Write Data Valid to Read Data Delay(1)
30
25
30
25
45
35
50
35
ns
tDDD
ns
2738 tbl 15a
7005X35
7005X55
7005X70
Com'l, Ind
& Military
Com'l, Ind &
Military
Military
Only
Symbol
BUSY TIMING (M/
Parameter
Min.
Max.
Min.
Max.
Min.
Max. Unit
S=VIH)
____
____
____
____
____
____
____
____
____
____
____
____
t
BAA
BDA
BAC
BDC
APS
BDD
WH
20
20
20
45
40
40
45
40
40
ns
ns
ns
ns
ns
ns
ns
BUSY Access Time from Address Match
BUSY Disable Time from Address Not Matched
BUSY Access Time from Chip Enable Low
BUSY Access Time from Chip Enable High
Arbitration Priority Set-up Time(2)
BUSY Disable to Valid Date(3)
Write Hold After BUSY(5)
t
t
t
20
____
35
____
35
____
t
5
____
5
____
5
____
t
35
____
40
____
45
____
t
25
25
25
BUSY TIMING (M/S=VIL
)
____
____
____
____
____
____
BUSY Input to Write(4)
Write Hold After BUSY(5)
t
WB
0
0
0
ns
ns
tWH
25
25
25
PORT-TO-PORT DELAY TIMING
____
____
____
____
____
____
t
WDD
Write Pulse to Data Delay(1)
Write Data Valid to Read Data Delay (1)
60
45
80
65
95
80
ns
tDDD
ns
2738 tbl 15b
NOTES:
1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read and BUSY".
2. To ensure that the earlier of the two ports wins.
3. tBDD is a calculated parameter and is the greater of 0, tWDD – tWP (actual) or tDDD – tDW (actual).
4. To ensure that the write cycle is inhibited on port "B" during contention with port "A".
5. To ensure that a write cycle is completed on port "B" after contention on port "A".
6. 'X' in part number indicates power rating (S or L).
61.422
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Timing Waveform of Write with Port-to-Port Read with BUSY(2,5)
(M/S = VIH)(4)
tWC
MATCH
ADDR"A"
t
WP
R/W"A"
t
DW
tDH
VALID
DATAIN "A"
(1)
APS
t
MATCH
ADDR"B"
tBDA
tBDD
BUSY"B"
tWDD
VALID
DATAOUT "B"
(3)
DDD
t
2738 drw 13
NOTES:
1. To ensure that the earlier of the two ports wins. tAPS is ignored for for M/S = VIL (slave).
2. CEL = CER = VIL
3. OE = VIL for the reading port.
4. If M/S = VIL (slave), then BUSY is an input (BUSY"A" =VIH), and BUSY"B" = "don't care", for this example.
5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite port "A".
Timing Waveform of Write with BUSY
tWP
R/W"A"
(3)
tWB
BUSY"B"
(1)
tWH
(2)
R/W"B"
2738 drw 14
NOTES:
1. tWH must be met for both BUSY input (slave) and output (master).
2. BUSY is asserted on Port "B", blocking R/W"B", until BUSY"B" goes HIGH
3. tWB is only for the 'Slave' Version..
6.42
13
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Waveform of BUSY Arbitration Controlled by CE Timing(1) (M/S = VIH)
ADDR"A"
ADDRESSES MATCH
and "B"
CE"A"
(2)
tAPS
CE"B"
tBAC
tBDC
BUSY"B"
2738 drw 15
Waveform of BUSY Arbitration Cycle Controlled by Address Match
Timing(1) (M/S = VIH)
ADDR"A"
ADDRESS "N"
(2)
APS
t
ADDR"B"
MATCHING ADDRESS "N"
tBAA
tBDA
BUSY"B"
2738 drw 16
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted.
AC Electrical Characteristics Over the
OperatingTemperatureandSupplyVoltageRange(1)
7005X15
7005X17
7005X20
Com'l, Ind
& Military
7005X25
Com'l &
Military
Com'l Only
Com'l Only
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Unit
INTERRUPT TIMING
____
____
____
____
____
____
____
____
t
AS
WR
INS
INR
Address Set-up Time
0
0
0
0
ns
ns
ns
t
Write Recovery Time
Interrupt Set Time
0
____
0
____
0
____
0
____
t
15
15
15
15
20
20
20
20
____
____
____
____
t
Interrupt Reset Time
ns
2738 tbl 16a
7005X35
7005X55
7005X70
Com'l, Ind
& Military
Com'l, Ind
& Military
Military
Only
Symbol
INTERRUPT TIMING
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
____
____
____
____
____
____
t
AS
WR
INS
INR
Address Set-up Time
Write Recovery Time
Interrupt Set Time
0
0
0
ns
ns
ns
t
0
____
0
____
0
____
t
25
25
40
40
50
50
____
____
____
t
Interrupt Reset Time
ns
2738 tbl 16b
NOTE:
1. 'X' in part number indicates power rating (S or L).
61.442
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Waveform of Interrupt Timing(1)
tWC
ADDR"A"
INTERRUPT SET ADDRESS(2)
(3)
AS
(4)
t
tWR
CE"A"
R/W"A"
INT"B"
(3)
INS
t
2738 drw 17
tRC
INTERRUPT CLEAR ADDRESS(2)
ADDR"B"
CE"B"
(3)
AS
t
OE"B"
(3)
INR
t
INT"B"
2738 drw 18
NOTES:
1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from port “A”.
2. See Interrupt Truth Table III.
3. Timing depends on which enable signal (CE or R/W) asserted last.
4. Timing depends on which enable signal (CE or R/W) is de-asserted first.
Truth Table III — Interrupt Flag(1,4)
Left Port
Right Port
R/W
L
A
12L-A0L
R/W
R
A
12R-A0R
Function
Set Right INT Flag
Reset Right INT Flag
Set Left INT Flag
Reset Left INT Flag
CE
L
OE
L
INT
L
CE
R
OE
R
INTR
L
X
X
X
L
X
X
L
X
1FFF
X
X
X
L(3)
H(2)
X
X
L
X
L
L
X
X
X
L(2)
H(3)
X
R
X
L
1FFF
1FFE
X
R
X
X
X
L
L
1FFE
X
X
X
L
2738 tbl 17
NOTES:
1. Assumes BUSYL = BUSYR = VIH.
2. If BUSYL = VIL, then no change.
3. If BUSYR = VIL, then no change.
4. INTR and INTL must be initialized at power-up.
6.42
15
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Truth Table IV — Address BUSY
Arbitration
Inputs
Outputs
A
-A
AOORL-A1122RL
Function
Normal
Normal
Normal
(1)
(1)
CE
L
CE
R
BUSY
L
BUSYR
X
H
X
L
X
X
H
L
NO MATCH
MATCH
H
H
H
H
MATCH
H
H
MATCH
(2)
(2)
Write Inhibit(3)
2738 tbl 18
NOTES:
1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSYX outputs on the IDT7005 are
push-pull, not open drain outputs. On slaves the BUSYX input internally inhibits writes.
2. 'L' if the inputs to the opposite port were stable prior to the address and enable inputs of this port. 'H' if the inputs to the opposite port became stable after the address
and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously.
3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored
when BUSYR outputs are driving LOW regardless of actual logic level on the pin.
Truth Table V — Example of Semaphore Procurement Sequence(1,2,3)
Functions
D0
- D7
Left
D0
- D7
Right
Status
No Action
1
1
Semaphore free
Left Port Writes "0" to Semaphore
Right Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "1" to Semaphore
Right Port Writes "0" to Semaphore
Right Port Writes "1" to Semaphore
Left Port Writes "0" to Semaphore
Left Port Writes "1" to Semaphore
0
0
1
1
0
1
1
1
0
1
1
1
0
0
1
1
0
1
1
1
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
2738 tbl 19
NOTES:
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT7005.
2. There are eight semaphore flags written to via I/O0 and read from all I/O's. These eight semaphores are addressed by A0 - A2.
3. CE=VIH, SEM=VIL to access the semaphores. Refer to the semaphore Read/Write Control Truth Table.
FunctionalDescription
(HEX), where a write is defined as CE = R/W= VIL per Truth Table III.
Theleftportclearstheinterruptthroughaccessofaddresslocation1FFE
when CE = OE = VIL. For this example, R/W is a "don't care". Likewise,
therightportinterruptflag(INTR)isassertedwhentheleftportwritesto
memory location 1FFF (HEX) and to clear the interrupt flag (INTR), the
rightportmustreadthememorylocation1FFF.Themessage(8bits)at
1FFEor1FFFisuser-defined,sinceitisanaddressableSRAMlocation.
Iftheinterruptfunctionisnotused,addresslocations1FFEand1FFFare
notusedasmailboxes,butaspartoftherandomaccessmemory.Refer
toTruthTableIIIfortheinterruptoperation.
TheIDT7005providestwoportswithseparatecontrol,addressand
I/Opinsthatpermitindependentaccessforreadsorwritestoanylocation
inmemory.TheIDT7005hasanautomaticpowerdownfeaturecontrolled
by CE. The CE controls on-chip power down circuitry that permits the
respectiveporttogointoastandbymodewhennotselected(CEHIGH).
Whenaportisenabled,accesstotheentirememoryarrayispermitted.
Interrupts
Iftheuserchoosestheinterruptfunction,amemorylocation(mailbox
or message center) is assigned to each port. The left port interrupt flag
(INTL) is asserted when the right port writes to memory location 1FFE
61.462
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
SLAVE
Dual Port
RAM
MASTER
Dual Port
RAM
CE
CE
BUSY (L) BUSY (R)
BUSY (L) BUSY (R)
MASTER
Dual Port
RAM
SLAVE
Dual Port
RAM
CE
CE
BUSY (R)
BUSY (R)
BUSY (L) BUSY (R)
BUSY (L)
BUSY (L)
,
2738 drw 19
Figure 3. Busy and chip enable routing for both width and depth expansion with IDT7005 RAMs.
BusyLogic
address signals only. It ignores whether an access is a read or write.
In a master/slave array, both address and chip enable must be valid
long enough for a BUSY flag to be output from the master before the
actualwritepulsecanbeinitiatedwiththeR/Wsignal.Failuretoobserve
thistimingcanresultinaglitchedinternalwriteinhibitsignalandcorrupted
dataintheslave.
BusyLogicprovidesahardwareindicationthatbothportsoftheRAM
haveaccessedthesamelocationatthesametime.Italsoallowsoneofthe
twoaccessestoproceedandsignalstheothersidethattheRAMis“busy”.
TheBUSYpincanthenbeusedtostalltheaccessuntiltheoperationon
theothersideiscompleted.Ifawriteoperationhasbeenattemptedfrom
thesidethatreceivesaBUSYindication,thewritesignalisgatedinternally
topreventthewritefromproceeding.
TheuseofBUSYlogicisnotrequiredordesirableforallapplications.
InsomecasesitmaybeusefultologicallyORtheBUSYoutputstogether
and use any BUSY indication as an interrupt source to flag the event of
anillegalorillogicaloperation.IfthewriteinhibitfunctionofBUSYlogicis
notdesirable,theBUSYlogiccanbedisabledbyplacingthepartinslave
modewiththeM/Spin.OnceinslavemodetheBUSYpinoperatessolely
asawriteinhibitinputpin.Normaloperationcanbeprogrammedbytying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
Semaphores
TheIDT7005isanextremelyfastDual-Port8Kx8CMOSStaticRAM
withanadditional8addresslocationsdedicatedtobinarysemaphoreflags.
TheseflagsalloweitherprocessorontheleftorrightsideoftheDual-Port
RAMtoclaimaprivilegeovertheotherprocessorforfunctionsdefinedby
thesystemdesigner’ssoftware.Asanexample,thesemaphorecanbe
usedbyoneprocessortoinhibittheotherfromaccessingaportionofthe
Dual-Port RAM or any other shared resource.
The Dual-Port RAM features a fast access time, and both ports are
completelyindependentofeachother.Thismeansthattheactivityonthe
leftportinnowayslowstheaccesstimeoftherightport. Bothportsare
identicalinfunctiontostandardCMOSStaticRAMandcanbereadfrom,
orwrittento,atthesametimewiththeonlypossibleconflictarisingfromthe
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphorelocation.Semaphoresareprotectedagainstsuchambiguous
situationsandmaybeusedbythesystemprogramtoavoidanyconflicts
inthenon-semaphoreportionoftheDual-PortRAM.Thesedeviceshave
anautomaticpower-downfeaturecontrolledbyCE,theDual-PortRAM
enable,andSEM,thesemaphoreenable.TheCEandSEMpinscontrol
on-chip power down circuitry that permits the respective port to go into
standbymodewhennotselected. Thisistheconditionwhichisshownin
Truth Table I where CE and SEM are both HIGH.
TheBUSYoutputsontheIDT7005RAMinmastermode,arepush-
pulltypeoutputsanddonotrequirepullupresistorstooperate. Ifthese
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
Width Expansion with Busy Logic
Master/SlaveArrays
WhenexpandinganIDT7005RAMarrayinwidthwhileusingBUSY
logic,onemasterpartisusedtodecidewhichsideoftheRAMarraywill
receiveaBUSYindication,andtooutputthatindication.Anynumberof
slavestobeaddressedinthesameaddressrangeasthemaster,usethe
BUSYsignalasawriteinhibitsignal.ThusontheIDT7005RAMtheBUSY
pinisanoutputifthepartisusedasamaster(M/Spin=VIH),andtheBUSY
pin is an input if the part used as a slave (M/S pin = VIL) as shown in
Figure 3.
SystemswhichcanbestusetheIDT7005containmultipleprocessors
or controllers and are typically very high-speed systems which are
softwarecontrolledorsoftwareintensive.Thesesystemscanbenefitfrom
aperformanceincreaseofferedbytheIDT7005'shardwaresemaphores,
whichprovidealockoutmechanismwithoutrequiringcomplexprogram-
ming.
Iftwoormoremasterpartswereusedwhenexpandinginwidth,asplit
decisioncouldresultwithonemasterindicatingBUSYononesideofthe
arrayandanothermasterindicatingBUSYononeothersideofthearray.
Thiswouldinhibitthewriteoperationsfromoneportforpartofawordand
inhibitthewriteoperationsfromtheotherportfortheotherpartoftheword.
The BUSY arbitration on a master is based on the chip enable and
Softwarehandshakingbetweenprocessorsoffersthemaximumin
systemflexibilitybypermittingsharedresourcestobeallocatedinvarying
6.42
17
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
configurations.TheIDT7005doesnotuseitssemaphoreflagstocontrol cause either signal (SEM or OE) to go inactive or the output will
anyresourcesthroughhardware,thusallowingthesystemdesignertotal never change.
flexibilityinsystemarchitecture.
AsequenceWRITE/READmustbeusedbythesemaphoreinorder
An advantage of using semaphores rather than the more common to guarantee that no system level contention will occur. A processor
methodsofhardwarearbitrationisthatwaitstatesareneverincurredin requestsaccesstosharedresourcesbyattemptingtowriteazerointoa
either processor. This can prove to be a major advantage in very semaphorelocation.Ifthesemaphoreisalreadyinuse,thesemaphore
high-speedsystems.
requestlatchwillcontainazero,yetthesemaphoreflagwillappearasone,
afactwhichtheprocessorwillverifybythesubsequentread(seeTruth
TableV).Asanexample,assumeaprocessorwritesazerototheleftport
atafreesemaphorelocation.Onasubsequentread,theprocessorwill
verifythatithaswrittensuccessfullytothatlocationandwillassumecontrol
overtheresourceinquestion.Meanwhile,ifaprocessorontherightside
attemptstowriteazerotothesamesemaphoreflagitwillfail, aswillbe
verifiedbythefactthataonewillbereadfromthatsemaphoreontheright
side during subsequent read. Had a sequence of READ/WRITE been
usedinstead,systemcontentionproblemscouldhaveoccurredduringthe
gap between the read and write cycles.
How the Semaphore Flags Work
Thesemaphorelogicisasetofeightlatcheswhichareindependent
oftheDual-PortRAM.Theselatchescanbeusedtopassaflag,ortoken,
fromoneporttotheothertoindicatethatasharedresourceisinuse.The
semaphores provide a hardware assist for a use assignment method
called“TokenPassingAllocation.”Inthismethod,thestateofasemaphore
latchisusedasatokenindicatingthatsharedresourceisinuse.Iftheleft
processorwantstousethisresource,itrequeststhetokenbysettingthe
latch.Thisprocessorthenverifiesitssuccessinsettingthelatchbyreading
it. If it was successful, it proceeds to assume control over the shared
resource.Ifitwasnotsuccessfulinsettingthelatch,itdeterminesthatthe
rightsideprocessorhassetthelatchfirst, hasthetokenandisusingthe
sharedresource.Theleftprocessorcantheneitherrepeatedlyrequest
thatsemaphore’sstatusorremoveitsrequestforthatsemaphoretoperform
anothertaskandoccasionallyattemptagaintogaincontrolofthetokenvia
thesetandtestsequence.Oncetherightsidehasrelinquishedthetoken,
theleftsideshouldsucceedingainingcontrol.
Itisimportanttonotethatafailedsemaphorerequestmustbefollowed
byeitherrepeatedreadsorbywritingaoneintothesamelocation. The
reasonforthisiseasilyunderstoodbylookingatthesimplelogicdiagram
ofthesemaphoreflaginFigure4.Twosemaphorerequestlatchesfeed
into a semaphore flag. Whichever latch is first to present a zero to the
semaphoreflagwillforceitssideofthesemaphoreflagLOWandtheother
sideHIGH.Thisconditionwillcontinueuntilaoneiswrittentothesame
semaphorerequestlatch.Shouldtheotherside’ssemaphorerequestlatch
havebeenwrittentoazerointhemeantime,thesemaphoreflagwillflip
overtotheothersideassoonasaoneiswrittenintothefirstside’srequest
latch.Thesecondside’sflagwillnowstayLOWuntilitssemaphorerequest
latchiswrittentoaone.Fromthisitiseasytounderstandthat,ifasemaphore
is requested and the processor which requested it no longer needs the
resource, the entire system can hang up until a one is written into that
semaphorerequestlatch.
ThesemaphoreflagsareactiveLOW.Atokenisrequestedbywriting
azerointoasemaphorelatchandisreleasedwhenthesamesidewrites
aonetothatlatch.
The eight semaphore flags reside within the IDT7005 in a separate
memoryspacefromtheDual-PortRAM.Thisaddressspaceisaccessed
byplacingaLOWinputontheSEMpin(whichactsasachipselectforthe
semaphore flags) and using the other control pins (Address, OE, and
R/W) as they would be used in accessing a standard static RAM. Each
oftheflagshasauniqueaddresswhichcanbeaccessedbyeitherside
throughaddresspinsA0–A2.Whenaccessingthesemaphores,noneof
theotheraddresspinshasanyeffect.
The critical case of semaphore timing is when both sides request a
single token by attempting to write a zero into it at the same time. The
semaphorelogicisspeciallydesignedtoresolvethisproblem.Ifsimulta-
neousrequestsaremade,thelogicguaranteesthatonlyonesidereceives
thetoken. Ifonesideisearlierthantheotherinmakingtherequest, the
firstsidetomaketherequestwillreceivethetoken.Ifbothrequestsarrive
at the same time, the assignment will be arbitrarily made to one port or
the other.
Whenwritingtoasemaphore,onlydatapinD0isused.IfaLOWlevel
iswrittenintoanunusedsemaphorelocation,thatflagwillbesettoazero
on that side and a one on the other side (see Truth Table V). That
semaphorecannowonlybemodifiedbythesideshowingthezero.When
aoneiswrittenintothesamelocationfromthesameside,theflagwillbe
settoaoneforbothsides(unlessasemaphorerequestfromtheotherside
ispending)andthencanbewrittentobybothsides. Thefactthattheside
whichisabletowriteazerointoasemaphoresubsequentlylocksoutwrites
fromtheothersideiswhatmakessemaphoreflagsusefulininterprocessor
communications.(Athoroughdiscussionontheuseofthisfeaturefollows
shortly.)Azerowrittenintothesamelocationfromtheothersidewillbe
storedinthesemaphorerequestlatchforthatsideuntilthesemaphoreis
freedbythefirstside.
One caution that should be noted when using semaphores is that
semaphoresalonedonotguaranteethataccesstoaresourceissecure.
Aswithanypowerfulprogrammingtechnique,ifsemaphoresaremisused
or misinterpreted, a software error can easily happen.
Initializationofthesemaphoresisnotautomaticandmustbehandled
viatheinitializationprogramatpower-up.Sinceanysemaphorerequest
flagwhichcontainsazeromustberesettoaone,allsemaphoresonboth
sidesshouldhaveaonewrittenintothematinitializationfrombothsides
to assure that they will be free when needed.
Whenasemaphoreflagisread,itsvalueisspreadintoalldatabitsso
thataflagthatisaonereadsasaoneinalldatabitsandaflagcontaining
azeroreadsasallzeros.Thereadvalueislatchedintooneside’soutput
UsingSemaphores—SomeExamples
Perhapsthesimplestapplicationofsemaphoresistheirapplicationas
registerwhenthatside'ssemaphoreselect(SEM)andoutputenable(OE) resourcemarkersfortheIDT7005’sDual-PortRAM.Saythe8Kx8RAM
signalsgoactive.Thisservestodisallowthesemaphorefromchanging wastobedividedintotwo4Kx8blockswhichweretobededicatedatany
stateinthemiddleofareadcycleduetoawritecyclefromtheotherside. onetimetoservicingeithertheleftorrightport.Semaphore0couldbeused
Becauseofthislatch,arepeatedreadofasemaphoreinatestloopmust toindicatethesidewhichwouldcontrolthelowersectionofmemory,and
61.482
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
Semaphore 1 could be defined as the indicator for the upper section of evenbeassigneddifferentmeaningsondifferentsidesratherthanbeing
memory.
Totakearesource,inthisexamplethelower4Kof Dual-PortRAM,
given a common meaning as was shown in the example above.
Semaphores are a useful form of arbitration in systems like disk
the processor on the left port could write and then read a zero in to interfaceswheretheCPUmustbelockedoutofasectionofmemoryduring
Semaphore0.Ifthistaskweresuccessfullycompleted(azerowasread atransferandtheI/Odevicecannottolerateanywaitstates.Withtheuse
back rather than a one), the left processor would assume control of the ofsemaphores,oncethetwodeviceshasdeterminedwhichmemoryarea
lower4K.Meanwhiletherightprocessorwasattemptingtogaincontrolof was“off-limits”totheCPU,boththeCPUandtheI/Odevicescouldaccess
theresourceaftertheleftprocessor,itwouldreadbackaoneinresponse theirassignedportionsofmemorycontinuouslywithoutanywaitstates.
tothezeroithadattemptedtowriteintoSemaphore0. Atthispoint, the
Semaphoresarealsousefulinapplicationswherenomemory“WAIT”
softwarecouldchoosetotryandgaincontrolofthesecond4Ksectionby stateisavailableononeorbothsides.Onceasemaphorehandshakehas
writing,thenreadingazerointoSemaphore1.Ifitsucceededingaining been performed, both processors can access their assigned RAM
control,itwouldlockouttheleftside.
segmentsatfullspeed.
Once the left side was finished with its task, it would write a one to
Anotherapplicationisintheareaofcomplexdatastructures.Inthis
Semaphore 0 and may then try to gain access to Semaphore 1. If case,blockarbitrationisveryimportant.Forthisapplicationoneprocessor
Semaphore1wasstilloccupiedbytherightside,theleftsidecouldundo mayberesponsibleforbuildingandupdatingadatastructure.Theother
itssemaphorerequestandperformothertasksuntilitwasabletowrite,then processorthenreadsandinterpretsthatdatastructure.Iftheinterpreting
readazerointoSemaphore1.Iftherightprocessorperformsasimilartask processorreadsanincompletedatastructure,amajorerrorconditionmay
withSemaphore0,thisprotocolwouldallowthetwoprocessorstoswap exist.Therefore,somesortofarbitrationmustbeusedbetweenthetwo
4K blocks of Dual-Port RAM with each other.
differentprocessors.Thebuildingprocessorarbitratesfortheblock,locks
The blocks do not have to be any particular size and can even be itandthenisabletogoinandupdatethedatastructure.Whentheupdate
variable, depending upon the complexity of the software using the is completed, the data structure block is released. This allows the
semaphoreflags.AlleightsemaphorescouldbeusedtodividetheDual- interpretingprocessortocomebackandreadthecompletedatastructure,
Port RAM or other shared resources into eight parts. Semaphores can therebyguaranteeingaconsistentdatastructure.
L PORT
R PORT
SEMAPHORE
REQUEST FLIP FLOP
SEMAPHORE
REQUEST FLIP FLOP
D0
D
D
D0
Q
Q
WRITE
WRITE
SEMAPHORE
READ
SEMAPHORE
,
READ
2738 drw 20
Figure 4. IDT7005 Semaphore Logic
6.42
19
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
OrderingInformation
XXXXX
A
999
A
A
A
A
Device Power Speed Package
Type
Process/
Temperature
Range
Tube or Tray
Tape and Reel
Blank
8
Blank Commercial (0°C to +70°C)
I(1)
B
Industrial (-40°C to +85°C)
Military (-55°C to +125°C)
Compliant to MIL-PRF-38538 QML
G(2)
Green
64-pin TQFP (PN64)
68-pin PGA (G68)
68-pin PLCC (J68)
PF
G
J
Commercial Only
Commercial Only
Commercial, Industrial & Military
Commercial & Military
Commercial, Industrial & Military
Commercial, Industrial & Military
Military Only
15
17
20
25
35
55
70
Speed in nanoseconds
S
L
Standard Power
Low Power
2738 drw 21
7005 64K (8K x 8) Dual-Port RAM
NOTES:
1. Industrial temperature range is available on selected TQFP packages in standard power.
For other speeds, packages and powers contact your sales office.
2. Green parts available. For specific speeds, packages and powers contact your local sales office.
DatasheetDocumentHistory
12/21/98:
Initiateddatasheetdocumenthistory
Convertedtonewformat
Cosmeticandtypographicalcorrections
Addedadditionalnotestopinconfigurations
Changeddrawingformat
Pages 2 & 3
06/03/99:
11/10/99:
08/07/00:
Replaced IDT logos
Page 1
Page 4
Page 6
Addedcopyrightinfo
Fixed overbar errors
Increasedstoragetemperatureparameter
ClarifiedTA Parameter
DCElectricalparameters–changedwordingfrom"open"to"disabled"
Changed±500mVto0mVinnotes
Addeddaterevisionforpinconfigurations
09/18/01:
Page 2 & 3
Page 14
Replaced one copy of table 13b with 13a for 15, 17,20 & 25ns speeds for AC Electrical Characteristics
INTERRUPT TIMING
62.402
IDT7005S/L
High-Speed 8K x 8 Dual-Port Static RAM
Military, Industrial and Commercial Temperature Ranges
DatasheetDocumentHistory(continued)
01/31/06:
Page 1
Addedgreenavailabilitytofeatures
Page 20
Addedgreenindicatortoorderinginformation
10/21/08:
09/17/12:
Page 20
Removed "IDT" from orderable part number
Pages 6,7,9,12,& 14
In all of the DC & AC Electrical tables the 7005X20 speed grade
changedfrom7005X20Com'l&MilitarytoincludeIndmakingit
Com'l, Ind&Military
Page 20
Added T& R indicator to ordering information
06/10/16:
Pages 2 & 3
Changed diagram for the PN64 pin configuration by rotating package pin labels and pin
numbers 90 degrees counter clockwise to reflect pin 1 orientation & added pin 1 dot at pin 1
PN64 pin configuration: removed the PN64 chamfer, the arrow and the index indicator
Added the IDT logo to all pin configurations and changed the text to be in
alignment with new diagram marking specs
Removedthedaterevisionindicatorfromallpinconfigurations
UpdatedfootnotereferencesforPN64pinconfiguration
The package codes PN64-1, G68-1 & J68-1 changed to PN64, G68 & J68 respectively to
matchstandardpackagecodes
Pages 2 & 27
CORPORATE HEADQUARTERS
for SALES:
for Tech Support:
408-284-2794
6024 Silver Creek Valley Road
San Jose, CA 95138
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
DualPortHelp@idt.com
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
6.42
21
相关型号:
7005L17JG
Dual-Port SRAM, 8KX8, 17ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, GREEN, PLASTIC, LCC-68
IDT
7005L17JG8
Dual-Port SRAM, 8KX8, 17ns, CMOS, PQCC68, 0.950 X 0.950 INCH, 0.120 INCH HEIGHT, GREEN, PLASTIC, LCC-68
IDT
7005L17PFG8
Dual-Port SRAM, 8KX8, 17ns, CMOS, PQFP64, 14 X 14 MM, 1.40 MM HEIGHT, GREEN, TQFP-64
IDT
©2020 ICPDF网 联系我们和版权申明