MK3723STRLF [IDT]
Clock Generator, 14MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8;型号: | MK3723STRLF |
厂家: | INTEGRATED DEVICE TECHNOLOGY |
描述: | Clock Generator, 14MHz, CMOS, PDSO8, 0.150 INCH, SOIC-8 时钟 光电二极管 外围集成电路 晶体 |
文件: | 总6页 (文件大小:78K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MK3723
LOW COST 3.3 VOLT VCXO
VIN is a high impedance input, it can be driven directly
from an PWM RC integrator circuit.
Description
The MK3723 series of devices includes the original
MK3723S and the new MK3723D. The MK3723D is a
drop-in replacement for the MK3723S device.
Compared to the earlier device, the MK3723D offers a
wider operating frequency range and improved power
supply noise rejection.
Features
• MK3723D is a drop-in replacement for the earlier
MK3723S device
• Packaged in 8 pin SOIC
• Operating voltage of 3.3 V (±5%)
The MK3723 is ICS’ low cost, low jitter, high
performance 3.3 volt VCXO designed to replace
expensive discrete VCXO modules. The on-chip
Voltage Controlled Crystal Oscillator accepts a 0 to
3.3V input voltage to cause the output clocks to vary by
±100 ppm. Using ICS’ patented VCXO techniques, the
device uses an inexpensive external pullable crystal in
the range of 16 - 28 MHz to produce a VCXO output
clock that is a divide by 2, 4, 6, or 8 of the crystal
frequency.
• VCXO Operational frequency range of 2 MHz to 14
MHz
• Uses an inexpensive external crystal
• On-chip patented VCXO with pull range of 200ppm
(minimum)
• VCXO tuning voltage of 0 to 3.3 V
• 12 mA output drive capability at TTL levels
• Advanced, low power, sub-micron CMOS process
ICS manufactures the largest variety of Set-Top Box
and multimedia clock synthesizers for all applications.
If more clock outputs are needed, see the MK3732 or
MK377x family of parts. Consult ICS to eliminate
VCXOs, crystals, and oscillators from your board.
• For frequencies between 8 MHz to 16 MHz, use the
MK3711D. For frequencies between 1 MHz and 8
MHz, use the MK3713D. For higher than 28 MHz,
use the MK3732-05.
The frequency of the on-chip VCXO is adjusted by an
external control voltage input into pin VIN. Because
MK3723D is Recommended for New Designs
Block Diagram
V DD
VIN
X1
Voltage
16-28 MH z
P ullable C rystal
C ontrolled
Crystal
V CX O CLK
/N
Oscillator
X2
S 1, S 0
GN D
MDS 3723 C
1
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
MK3723
LOW COST 3.3 VOLT VCXO
Pin Assignment
Divider Select Table
S1
0
S0
0
VCXOCLK (MHz)
Crystal ÷ 2
Crystal ÷ 4
Crystal ÷ 6
Crystal ÷ 8
X 1
V D D
V I N
8
7
6
5
1
2
3
4
X 2
S 1
0
1
V C X O C L K
S 0
1
0
G N D
1
1
0 = connect to ground, 1=connect to VDD
M K 3 7 2 3 S
M K 3 7 2 3 D
8 P i n ( 1 5 0 m i l ) S O I C
Pin Descriptions
Pin
Pin
Pin
Pin Description
Number
Name
Type
1
2
3
XI
Input
Crystal connection. Connect to a pullable 16-28 MHz crystal.
VDD
VIN
Power Connect to +3.3 V (0.01uf decoupling capacitor recommended).
Input
Voltage input to VCXO. Zero to 3.3V signal which controls the VCXO
frequency.
4
5
6
7
8
GND
S0
Power Connect to ground.
Input Select pin for VCXO divider. See table above.
VCXOCLK Output VXCO clock output. Full CMOS output amplitude.
S1
X2
Input
Input
Select pin for VCXO divider. See table above.
Crystal connection. Connect to a pullable 16 - 28 MHz crystal.
MDS 3723 C
2
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
MK3723
LOW COST 3.3 VOLT VCXO
The external crystal must be connected as close to the
chip as possible and should be on the same side of the
PCB as the MK3723. There should be no via’s between
the crystal pins and the X1 and X2 device pins. There
should be no signal traces underneath or close to the
crystal. See application note MAN05.
External Component Selection
The MK3723 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
A decoupling capacitor of 0.01µF should be connected
between VDD and GND on pin 2 and 4, as close to the
MK3723 as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors
on the PCB is optional. The need for these capacitors
is determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture
and frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
Series Termination Resistor
When the PCB trace between the clock output and the
load is over 1 inch, series termination should be used.
To series terminate a 50Ω trace (a commonly used
trace impedance) place a 33Ω resistor in series with
the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20Ω.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of
your final layout, a frequency counter capable of about
1 ppm resolution and accuracy, two power supplies,
and some samples of the crystals which you plan to
use in production, along with measured initial accuracy
for each crystal at the specified crystal load
capacitance, CL.
Quartz Crystal
The MK3723 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To
assure the best system performance (frequency pull
range) and reliability, a crystal device with the
recommended parameters (shown below) must be
used, and the layout guidelines discussed in the
following section must be followed.
To determine the value of the crystal capacitors:
1. Connect VDD of the MK3723 to 3.3V. Connect pin 3
of the MK3723 to the second power supply. Adjust the
voltage on pin 3 to 0V. Measure and record the
frequency of the CLK output.
2. Adjust the voltage on pin 3 to 3.3V. Measure and
record the frequency of the same output.
The frequency of oscillation of a quartz crystal is
determined by its “cut” and by the load capacitors
connected to it. The MK3723 incorporates on-chip
variable load capacitors that “pull” (change) the
frequency of the crystal. The crystal specified for use
with the MK3723 is designed to have zero frequency
error when the total of on-chip + stray capacitance is
14pF.
To calculate the centering error:
(f3.0V – ftarget) + (f0V – ftarget
)
Error = 106x ------------------------------------------------------------------------------ – e r r o r xtal
ft arget
Recommended Crystal Parameters:
Initial Accuracy at 25°C
Temperature Stability
Aging
Load Capacitance
Shunt Capacitance, C0
C0/C1 Ratio
±20 ppm
±30 ppm
±20 ppm
14 pf
7 pF Max
250 Max
35 Ω Max
Where:
ftarget = nominal crystal frequency
errorxtal =actual initial accuracy (in ppm) of the crystal
being measured
Equivalent Series Resistance
MDS 3723 C
3
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
MK3723
LOW COST 3.3 VOLT VCXO
If the centering error is less than ±25 ppm, no
pin to ground. The value for each of these caps (in pF)
is given by:
adjustment is needed. If the centering error is more
than 25ppm negative, the PC board has excessive
stray capacitance and a new PCB layout should be
considered to reduce stray capacitance. (Alternately,
the crystal may be re-specified to a higher load
capacitance. Contact ICS MicroClock for details.) If the
centering error is more than 25ppm positive, add
identical fixed centering capacitors from each crystal
External Capacitor =
2 x (centering error)/(trim sensitivity)
Trim sensitivity is a parameter which can be supplied
by your crystal vendor. If you do not know the value,
assume it is 30 ppm/pF. After any changes, repeat the
measurement to verify that the remaining error is
acceptably low (typically less than ±25ppm).
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the MK3723. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
All Inputs and Outputs
7V
-0.5V to VDD+0.5V
0 to +70°C
Ambient Operating Temperature
Storage Temperature
-65 to +150°C
260°C
Soldering Temperature
Recommended Operation Conditions
Parameter
Min.
Typ.
Max.
+70
Units
°C
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
Reference crystal parameters
0
–
+3.15
+3.45
V
Refer to page 3
MDS 3723 C
4
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
MK3723
LOW COST 3.3 VOLT VCXO
DC Electrical Characteristics
VDD=3.3V ±5% , Ambient temperature 0 to +70°C, unless stated otherwise
Parameter
Operating Voltage
Symbol
VDD
VOH
Conditions
Min.
3.15
2.4
Typ.
Max.
Units
3.45
V
V
V
V
Output High Voltage
Output Low Voltage
IOH = -12 mA
IOL = 12 mA
IOH = -4 mA
VOL
0.4
Output High Voltage (CMOS
Level)
VOH
VDD-0.4
2.0
Input High Voltage, S1:S0
Input Low Voltage, S1:S0
Operating Supply Current
Short Circuit Current
VIH
VIL
V
V
0.8
3.3
IDD
IOS
VIA
No load
5
mA
mA
V
±50
VIN, VCXO Control Voltage
0
AC Electrical Characteristics
VDD = 3.3V ±5%, Ambient Temperature 0 to +70° C, unless stated otherwise
Parameter
Input Crystal Frequency
Output Frequency
Crystal Pullability
MK3723D
Symbol
Conditions
Min. Typ. Max. Units
FI
16
2
28
14
MHz
MHz
FO
FP
FP
0V< VIN < 3.3V, Note 1
0V< VIN < 3.3V, Note 1
+ 115
+ 100
ppm
ppm
MK3723S
VCXO Gain
MK3723D
VIN = VDD/2 + 1V, Note 1
VIN = VDD/2 + 1V, Note 1
0.8 to 2.0V, CL=15pF
2.0 to 0.8V, CL=15pF
Measured at 1.4V, CL=15pF
CL=15pF
120
140
ppm/V
ppm/V
ns
MK3723S
Output Rise Time
Output Fall Time
Output Clock Duty Cycle
tOR
tOF
tD
1.5
1.5
60
ns
40
50
75
%
Maximum Output Jitter,
short term
tJ
ps
Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3.
MDS 3723 C
5
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
MK3723
LOW COST 3.3 VOLT VCXO
Package Outline and Package Dimensions (8 pin SOIC)
Package dimensions are kept current with JEDEC Publication No. 95
Millimeters
Inches
Min Max
Symbol
Min
1.35
1.10
0.33
0.19
4.80
3.80
Max
1.75
0.25
0.51
0.25
5.00
4.00
A
A1
B
C
D
E
e
0.0532 0.0688
0.0040 0.0098
0.013
0.0075 0.0098
.1890 .1968
0.020
Index
Area
E
H
0.1497 0.1574
0.050 Basic
1.27 Basic
H
h
L
5.80
0.25
0.40
0°
6.20
0.50
1.27
8°
0.2284 0.2440
0.010
0.016
0°
0.020
0.050
8°
Pin 1
a
D
h x 450
A
Q
c
e
b
Ordering Information
Part / Order Number
(Note 1)
Marking
Shipping
packaging
Package
Temperature
MK3723D
MK3723D
MK3723D
MK3723S
MK3723S
Tubes
8 pin SOIC
8 pin SOIC
8 pin SOIC
8 pin SOIC
0 to +70° C
0 to +70° C
0 to +70° C
0 to +70° C
MK3723DTR
MK3723S
Tape and Reel
Tubes
MK3723STR
Tape and Reel
Note 1: MK3723D is recommended for new designs.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
MDS 3723 C
6
Revision 070601
Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com
相关型号:
MK3724GILFT
Clock Generator, 73.728MHz, CMOS, PDSO16, 4.40 MM, 0.65 MM PITCH, LEAD FREE, TSSOP-16
IDT
MK3724GLFT
Clock Generator, 73.728MHz, CMOS, PDSO16, 4.40 MM, 0.65 MM PITCH, LEAD FREE, TSSOP-16
IDT
©2020 ICPDF网 联系我们和版权申明