5962-0254901HZC [INFINEON]
DC-DC Regulated Power Supply Module, 1 Output, 66W, Hybrid,;
| 型号： | 5962-0254901HZC |
| 厂家： | 
Infineon |
| 描述： | DC-DC Regulated Power Supply Module, 1 Output, 66W, Hybrid, |
| 文件： | 总14页 (文件大小：169K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
Update drawing to the latest requirements. -sld
07-05-02
09-11-24
Robert M. Heber
Charles F. Saffle
Table II, add note to Group C end-point test parameters. -gz
C
Corrected dimensions for symbols D, D2, and L1 for case outline U.
Corrected dimensions for symbols D2, L, and L1 for case outline X.
Corrected dimensions for symbols D, L, and L1 for case outline Y.
Corrected dimensions for symbols D, D2, and L1 for case outline Z.
Updated drawing paragraphs. -sld
13-01-23
Charles F. Saffle
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
REV
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
C
C
C
SHEET
10
11
12
13
PMIC N/A
PREPARED BY
Gary Zahn
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Greg Cecil
APPROVED BY
Raymond Monnin
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
MICROCIRCUIT, HYBRID, LINEAR, 8 VOLT,
SINGLE CHANNEL, DC/DC CONVERTER
DRAWING APPROVAL DATE
02-11-06
AMSC N/A
REVISION LEVEL
C
SIZE
A
CAGE CODE
5962-02549
67268
SHEET
1 OF 13
DSCC FORM 2233
APR 97
5962-E149-13
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
-
02549
01
H
X
X
RHA
Federal
stock class
designator
\
Device
type
Device
class
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
designator
(see 1.2.1)
(see 1.2.2)
designator
(see 1.2.3)
/
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
Generic number
AFL12008S/CH
Circuit function
DC/DC converter, 80 W, +8 V output
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
H
G
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
E
D
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
U
X
Y
Z
See figure 1
See figure 1
See figure 1
See figure 1
12
12
12
12
Y case configuration with leads bent upwards
Straight leads with end mounting through holes
Straight leads with side mounting through holes
Y case configuration with leads bent downwards
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-02549
A
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
2
DSCC FORM 2234
APR 97
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage range....................................................................
Lead temperature (soldering, 10 seconds) ................................
Storage temperature..................................................................
-0.5 V dc to +180 V dc
+300°C
-65°C to +135°C
1.4 Recommended operating conditions.
Input voltage range....................................................................
Output power 2/ .........................................................................
Case operating temperature range (TC).....................................
+80 V dc to +160 V dc
≤ 80 W
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ Derate output power linearly above case temperature +125°C to 0 at +135°C.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2) TA as specified in accordance with table I of method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
Group A
Device
Limits
Unit
-55°C ≤ T ≤ +125°C
subgroups type
C
V
IN = 120 V dc ±5%, CL = 0
Min
Max
unless otherwise specified
Output voltage
VOUT
IOUT = 10 A
1
01
+7.92
+7.84
+8.08
+8.16
10
V
A
2,3
Output current 2/
IOUT
VRIP
VIN = 80, 120, and 160 V dc
1,2,3
01
01
Output ripple voltage
VIN = 80, 120, and 160 V dc,
B.W. = 10 MHz
1,2,3
1,2,3
1,2,3
100
±20
±80
mV p-p
mV
Line regulation
Load regulation
Input current
VRLINE
VRLOAD
IIN
VIN = 80, 120, and 160 V dc,
IOUT = 0, 5, and 10 A
01
01
01
VIN = 80, 120, and 160 V dc,
IOUT = 0, 5, and 10 A
mV
IOUT = no load
1
30
40
3
mA
2,3
Enable 1, (pin 4) shorted to
Input return (pin 2)
1,2,3
Enable 2, (pin 12) shorted to
Output return (pin 8)
1,2,3
5
Input ripple current
Efficiency
IRIP
IOUT = 10 A, B.W. = 10 MHz
IOUT = 10 A
1,2,3
1,2,3
1
01
01
01
60
mA p-p
%
EFF
ISO
79
Isolation
Input to output or any pin to
case (except pin 3) at
500 V dc, TC = +25°C
100
MΩ
Maximum capacitive load 3/
Power dissipation load fault
CL
PD
No effect on dc
01
01
10,000
µF
4
performance, TC = +25°C
Overload
1,2,3
32
32
W
Short circuit
See footnotes at end of table.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-02549
A
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/
Group A
subgroups
Device
type
Limits
Unit
-55°C ≤ T ≤ +125°C
C
VIN = 120 V dc ±5%, CL = 0
Min
Max
unless otherwise specified
Current limit point 4/
ICL
VOUT = 90% VNOM
1
01
11.50
10.50
12.50
12.50
11.50
14.00
600
A
2
3
Switching frequency
Sync frequency range
FS
IOUT = 10 A
1,2,3
1,2,3
4,5,6
01
01
01
500
kHz
FSYNC
VOTLOAD
IOUT = 10 A
500
-500
-500
700
kHz
Output response to step
transient load changes 5/ 6/
50% to/from 100%
10% to/from 50%
50% to/from 100%
+500
+500
200
mV pk
Recovery time, step transient
load changes 5/ 6/
TTLOAD
4,5,6
4,5,6
01
01
µs
10% to/from 50%
400
Output response to transient
step line changes 3/ 5/ 7/
VOTLINE
Input step, 80 V to/from
160 V dc, IOUT = 10 A
-500
+500
mV pk
Recovery time transient step
line changes 3/ 5/ 7/
TTLINE
Input step, 80 V to/from
160 V dc, IOUT = 10 A
4,5,6
4,5,6
01
01
500
250
µs
Turn on overshoot 8/
VTonOS
IOUT = 0 and 10 A
IOUT = 0 and 10 A
mV pk
Turn on delay 8/
TonD
TrLF
4,5,6
4,5,6
01
01
120
120
ms
ms
Load fault recovery 8/
1/ All electrical tests are performed with the remote sense leads connected to the output leads at the load. Pin 10 to pin 7
and pin 9 to pin 8.
2/ Parameter verified as part of another test.
3/ Parameter not 100% tested but are guaranteed to the limits specified in the table.
4/ Current limit point is that condition of excess load causing output voltage to drop to 90% of nominal.
5/ Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of VOUT at
50% load.
6/ Load transient transition time ≥ 10 µs.
7/ Line transient transition time ≥ 100 µs.
8/ Turn-on delay is measured with an input voltage rise time of between 100 and 500 volts per millisecond.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
6
DSCC FORM 2234
APR 97
Case outline U.
Millimeters
Inches
Symbol
A
Min
Max
9.65
Min
Max
.380
2.833
2.505
.535
1.505
2.01
1.005
.055
.43
D
70.35
63.37
13.08
37.97
50.6
25.27
1.14
10.4
71.96
63.63
13.59
38.23
51.1
25.53
1.40
10.9
2.770
2.495
.515
1.495
1.99
.995
.045
.41
D1
D2
E
e1
e2
F
L
L1
q
5.33
5.84
.210
1.745
1.145
1.745
.24
.295
.370
.245
.035
.135
.230
1.755
1.155
1.755
.26
.305
.380
.255
.045
.145
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
44.58
29.34
44.58
6.6
7.75
9.65
6.48
1.14
3.68
q1
q2
q3
q4
q5
S
∅b
∅p
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outlines.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
7
DSCC FORM 2234
APR 97
Case outline X.
Millimeters
Inches
Symbol
A
Min
Max
9.65
Min
Max
.380
D
76.07
63.37
76.33
63.63
76.23
38.23
5.21
2.995
2.495
3.005
2.505
3.001
1.505
.205
D1
D2
E
37.97
4.95
1.14
1.495
.195
.045
e1
F
1.40
.055
L
L1
q
q1
S
∅b
∅p
6.30
.248
5.34
69.98
31.88
6.22
5.84
.210
2.755
1.255
.245
.230
70.23
32.13
6.48
1.14
3.38
2.765
1.265
.255
.045
.133
0.89
.035
3.12
.123
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outlines - Continued.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
8
DSCC FORM 2234
APR 97
Case outline Y.
Millimeters
Inches
Symbol
A
Min
Max
9.65
76.23
63.63
38.23
51.1
5.21
1.40
6.30
5.84
44.58
29.34
44.58
6.6
Min
Max
.380
D
3.001
2.505
1.505
2.01
.205
.055
.248
.230
1.755
1.155
1.755
.26
D1
E
e1
e2
F
L
L1
q
q1
q2
q3
q4
q5
S
63.37
37.97
50.6
2.495
1.495
1.99
4.95
.195
.045
1.14
5.34
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
.210
1.745
1.145
1.745
.24
7.75
9.65
6.48
1.14
3.68
.295
.370
.245
.035
.135
.305
.380
.255
.045
.145
∅b
∅p
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outlines - Continued.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
9
DSCC FORM 2234
APR 97
Case outline Z.
Millimeters
Inches
Symbol
A
Min
Max
9.65
71.96
63.63
13.59
38.23
51.1
25.53
1.40
9.4
Min
Max
.380
2.833
2.505
.535
1.505
2.01
1.005
.055
.37
D
70.35
63.37
13.08
37.97
50.6
25.27
1.14
8.9
2.770
2.495
.515
1.495
1.99
.995
.045
.35
D1
D2
E
e1
e2
F
L
L1
q
5.33
44.32
29.08
44.32
6.1
7.49
9.40
6.22
0.89
3.43
5.84
44.58
29.34
44.58
6.6
7.75
9.65
6.48
1.14
3.68
.210
1.745
1.145
1.745
.24
.295
.370
.245
.035
.135
.230
1.755
1.155
1.755
.26
.305
.380
.255
.045
.145
q1
q2
q3
q4
q5
S
∅b
∅p
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-
pound units shall rule.
2. Lead identification for reference only.
3. Case outline weight: 92 grams maximum.
FIGURE 1. Case outlines - Continued.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
10
DSCC FORM 2234
APR 97
Device type
01
U, X, Y, and Z
Terminal symbol
Positive input
Input return
Case
Case outlines
Terminal number
1
2
3
4
Enable 1
5
Sync output
Sync input
6
7
Positive output
Output return
Return sense
Positive sense
Share
8
9
10
11
12
Enable 2
FIGURE 2. Terminal connections.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-02549
A
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
11
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
Final electrical parameters
Group A test requirements
---
1*, 2, 3, 4, 5, 6
1, 2, 3, 4, 5, 6
1, 2, 3, 4
Group C end-point electrical
parameters 1/
End-point electrical parameters
for radiation hardness assurance
(RHA) devices
Not applicable
*
PDA applies to subgroup 1.
1/ As a minimum, for all Group C testing performed after November 24, 2009
manufacturers shall perform subgroups 1, 2, and 3 from the Group A
electrical test table (Table C-Xa of MIL-PRF-38534).
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. Tests shall be as specified in table II herein.
b. Subgroups 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2) T as specified in accordance with table I of method 1005 of MIL-STD-883.
A
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-02549
A
REVISION LEVEL
SHEET
DLA LAND AND MARITIME
C
12
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-
38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors, listed in MIL-HDBK-
103 and QML-38534, have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have
agreed to this drawing.
SIZE
STANDARD
5962-02549
A
MICROCIRCUIT DRAWING
REVISION LEVEL
C
SHEET
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
13
DSCC FORM 2234
APR 97
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 13-01-23
Approved sources of supply for SMD 5962-02549 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-0254901HUA
5962-0254901HUC
52467
52467
AFL12008SW/CH
AFL12008SW/CH
5962-0254901HXA
5962-0254901HXC
52467
52467
AFL12008SX/CH
AFL12008SX/CH
5962-0254901HYA
5962-0254901HYC
52467
52467
AFL12008SY/CH
AFL12008SY/CH
5962-0254901HZA
5962-0254901HZC
52467
52467
AFL12008SZ/CH
AFL12008SZ/CH
1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the
manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its
availability.
2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the
performance requirements of this drawing.
Vendor CAGE
number
Vendor name
and address
52467
International Rectifier Corporation
2520 Junction Ave.
San Jose, CA 95134
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明