首页 |元器件品牌

5962-9235101HZC [INFINEON]

DC-DC Regulated Power Supply Module, 2 Output, 12W, Hybrid, FM-8;
5962-9235101HZC
型号： 5962-9235101HZC
厂家： Infineon    Infineon
描述：

DC-DC Regulated Power Supply Module, 2 Output, 12W, Hybrid, FM-8

局域网 输出元件
文件： 总13页 (文件大小：69K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
REVISIONS  
LTR  
A
DESCRIPTION  
DATE (YR-MO-DA)  
95-04-11  
APPROVED  
Added case outline Z. Made corrections to table I and to figure 1,  
case outline X, dimension A.  
K. A. Cottongim  
B
C
Figure 1; changed the dimension (S) min and max limits for case  
outline Z. Editorial changes throughout. -sld  
00-05-25  
11-12-01  
Raymond Monnin  
Charles F. Saffle  
Table II, add note to Group C end-point test parameters. Update  
boilerplate paragraphs. -gz  
REV  
SHEET  
REV  
SHEET  
REV STATUS  
OF SHEETS  
REV  
C
1
C
2
C
3
C
4
C
5
C
6
C
7
C
8
C
9
C
C
C
SHEET  
10  
11  
12  
PMIC N/A  
PREPARED BY  
Gary Zahn  
DLA LAND AND MARITIME  
STANDARD  
CHECKED BY  
COLUMBUS, OHIO 43218-3990  
Steve L. Duncan  
MICROCIRCUIT  
DRAWING  
http://www.landandmaritime.dla.mil  
APPROVED BY  
THIS DRAWING IS AVAILABLE  
FOR USE BY ALL  
DEPARTMENTS  
AND AGENCIES OF THE  
DEPARTMENT OF DEFENSE  
Kendall A. Cottongim  
MICROCIRCUIT, HYBRID, LINEAR, 15 VOLT,  
DUAL CHANNEL, DC/DC CONVERTER  
DRAWING APPROVAL DATE  
92-10-15  
AMSC N/A  
REVISION LEVEL  
SIZE  
A
CAGE CODE  
5962-92351  
67268  
C
SHEET  
1 OF 12  
DSCC FORM 2233  
APR 97  
5962-E087-12  
1. SCOPE  
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A  
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When  
available, a choice of radiation hardness assurance levels are reflected in the PIN.  
1.2 PIN. The PIN shall be as shown in the following example:  
5962  
-
92351  
01  
H
X
X
Federal  
stock class  
designator  
\
RHA  
designator  
(see 1.2.1)  
Device  
type  
(see 1.2.2)  
Device  
class  
designator  
(see 1.2.3)  
Case  
outline  
(see 1.2.4)  
Lead  
finish  
(see 1.2.5)  
/
\/  
Drawing number  
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA  
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.  
1.2.2 Device type. The device type identify the circuit function as follows:  
Device type  
01  
Generic number  
AHF2815D/CH  
Circuit function  
DC/DC converter, 12 W, 15 V output  
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.  
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,  
and E) or QML Listing (Class G and D). The product assurance levels are as follows:  
Device class  
K
Device performance documentation  
Highest reliability class available. This level is intended for use in space  
applications.  
H
G
Standard military quality class level. This level is intended for use in applications  
where non-space high reliability devices are required.  
Reduced testing version of the standard military quality class. This level uses the  
Class H screening and In-Process Inspections with a possible limited temperature  
range, manufacturer specified incoming flow, and the manufacturer guarantees (but  
may not test) periodic and conformance inspections (Group A, B, C, and D).  
E
D
Designates devices which are based upon one of the other classes (K, H, or G)  
with exception(s) taken to the requirements of that class. These exception(s) must  
be specified in the device acquisition document; therefore the acquisition document  
should be reviewed to ensure that the exception(s) taken will not adversely affect  
system performance.  
Manufacturer specified quality class. Quality level is defined by the manufacturers  
internal, QML certified flow. This product may have a limited temperature range.  
SIZE  
STANDARD  
MICROCIRCUIT DRAWING  
5962-92351  
A
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
2
DSCC FORM 2234  
APR 97  
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:  
Outline letter  
Descriptive designator  
Terminals  
Package style  
X
Z
See figure 1  
See figure 1  
8
8
Dual in-line package  
Flange package  
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.  
1.3 Absolute maximum ratings. 1/  
Input voltage range...................................................................................  
Power dissipation (PD)..............................................................................  
Lead temperature (soldering, 10 seconds)...............................................  
Storage temperature range.......................................................................  
-0.5 V dc to +50 V dc  
6 W  
+300C  
-65C to +150C  
1.4 Recommended operating conditions.  
Input voltage range...................................................................................  
Output power 2/ 3/ ...................................................................................  
Case operating temperature range (TC) ...................................................  
+16 V dc to +40 V dc  
12 W  
-55C to +125C  
2. APPLICABLE DOCUMENTS  
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a  
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in  
the solicitation or contract.  
DEPARTMENT OF DEFENSE SPECIFICATION  
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.  
DEPARTMENT OF DEFENSE STANDARDS  
MIL-STD-883 - Test Method Standard Microcircuits.  
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.  
DEPARTMENT OF DEFENSE HANDBOOKS  
MIL-HDBK-103 - List of Standard Microcircuit Drawings.  
MIL-HDBK-780 - Standard Microcircuit Drawings.  
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization  
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)  
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text  
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a  
specific exemption has been obtained.  
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the  
maximum levels may degrade performance and affect reliability.  
2/ Derate output power linearly above case temperature +125C to 0 at +135C.  
3/ Up to 90 percent of full power is available from either output provided the total output power does not exceed 12 watts.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
3
DSCC FORM 2234  
APR 97  
3. REQUIREMENTS  
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in  
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as  
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The  
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as  
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not  
affect the form, fit, or function of the device for the applicable device class.  
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified  
in MIL-PRF-38534 and herein.  
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.  
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.  
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are  
as specified in table I and shall apply over the full specified operating temperature range.  
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical  
tests for each subgroup are defined in table I.  
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with  
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.  
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described  
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot  
sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for  
those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer  
and be made available to the preparing activity (DLA Land and Maritime-VA) upon request.  
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this  
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the  
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.  
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of  
microcircuits delivered to this drawing.  
4. VERIFICATION  
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as  
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the  
form, fit, or function as described herein.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
4
DSCC FORM 2234  
APR 97  
TABLE I. Electrical performance characteristics.  
Test  
Symbol  
Conditions  
Group A  
subgroups  
Device  
type  
Limits  
Unit  
-55C TC +125C  
IN = 28 V dc 5%, CL = 0  
unless otherwise specified  
V
Min  
Max  
Output voltage  
VOUT  
IOUT = 0  
1
01  
V
14.85 15.15  
14.70 15.30  
2,3  
Output current 1/ 2/  
Output ripple voltage 3/  
Line regulation 4/  
Load regulation 4/  
Cross regulation 5/  
Input current  
IOUT  
VIN = 16, 28, and 40 V dc,  
each output  
1,2,3  
01  
01  
01  
01  
01  
01  
80  
720  
60  
mA  
VRIP  
VIN = 16, 28, and 40 V dc  
B.W.= 20 Hz to 2 MHz  
1,2,3  
1,2,3  
1,2,3  
1,2,3  
1,2,3  
mV p-p  
mV  
VRLINE  
VRLOAD  
VRCROS  
IIN  
VIN = 16, 28, and 40 V dc  
35  
I
OUT = 0, 400, and 800 mA )  
VIN = 16, 28, and 40 V dc  
OUT = 0, 400, and 800 mA  
35  
mV  
I
10 percent to 90 percent  
load change each output  
3.0  
%
IOUT = 0, inhibit (pin 1) tied to  
input return (pin 7)  
12  
60  
mA  
I
OUT = 0,  
inhibit (pin 1) = open  
Input ripple current 3/ 4/  
Efficiency 4/  
IRIP  
IOUT = 800 mA  
1,2,3  
1,3  
01  
01  
50  
mA p-p  
%
B.W.= 20 Hz to 2 MHz  
EFF  
IOUT = 800 mA  
78  
2
1
74  
Isolation  
ISO  
Input to output or any pin to  
case (except pin 6) at 500 V  
dc, TC = +25C  
01  
100  
M  
Capacitive load 6/ 7/  
CL  
PD  
No effect on dc performance,  
TC = +25C, total for both  
outputs  
4
01  
01  
200  
6
F  
Power dissipation load  
fault  
Overload 8/  
1,2,3  
W
Short circuit  
2.5  
See footnotes at end of table.  
SIZE  
STANDARD  
MICROCIRCUIT DRAWING  
5962-92351  
A
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
5
DSCC FORM 2234  
APR 97  
TABLE I. Electrical performance characteristics - Continued.  
Test  
Symbol  
Conditions  
Group A  
subgroups  
Device  
type  
Limits  
Unit  
-55C TC +125C  
IN = 28 V dc 5%, CL = 0  
unless otherwise specified  
V
Min  
500  
Max  
600  
Switching frequency 4/  
FS  
IOUT = 800 mA  
4,5,6  
01  
kHz  
Output response to step  
transient load changes  
4/ 9/  
VOTLOAD 400 mA to/from 800 mA  
0 mA to/from 400 mA  
4,5,6  
4,5,6  
4,5,6  
4,5,6  
01  
01  
01  
01  
-200  
+200  
+800  
70  
mV pk  
-800.00  
Recovery time, step  
Transient load changes  
4/ 9/ 10/  
TTLOAD  
400 mA to/from 800 mA  
0 mA to/from 400 mA  
s  
2000  
Output response transient  
step line changes  
4/ 7/ 11/  
VOTLINE  
Input step from/to 16 to 40 V  
dc, IOUT = 800 mA  
4,5,6  
4,5,6  
01  
01  
-750  
+750  
1200  
mV pk  
Recovery time transient  
tep line changes  
4/ 7/ 10/ 11/  
TTLINE  
Input step from/to 16 to 40 V  
dc, IOUT = 800 mA  
s  
Turn on overshoot 4/  
Turn on delay 4/ 12/  
Load fault recovery 7/  
VTonOS  
TonD  
IOUT = 0 and 800 mA  
IOUT = 0 and 800 mA  
4,5,6  
4,5,6  
4,5,6  
01  
01  
750  
25  
mV pk  
ms  
TrLF  
25  
ms  
01  
See footnotes at top of next page.  
SIZE  
STANDARD  
MICROCIRCUIT DRAWING  
5962-92351  
A
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
6
DSCC FORM 2234  
APR 97  
TABLE I. Electrical performance characteristics - Continued.  
1/ Parameter guaranteed by line, load, and cross regulation tests.  
2/ Up to 90 percent of full power is available from either output provided the total output does not exceed 12 W.  
3/ Bandwidth guaranteed by design. Tested for 20 kHz to 2 MHz.  
4/ Load current split equally between +V  
and -V  
.
OUT  
OUT  
5/ 1.2 watt load on output under test, 1.2 watt to 10.8 watt load change on other output.  
6/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load  
in excess of the maximum limit will not disturb loop stability but may interfere with the operation of the load fault detection  
circuitry, appearing as a short circuit during turn-on.  
7/ Parameters shall be tested as part of design characterization and after design or process changes. Parameters shall be  
guaranteed to the limits specified in table I for all lots not specifically tested.  
8/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit  
protection and is the condition of maximum power dissipation.  
9/ Load step transition time between 2 and 10 microseconds.  
10/ Recovery time is measured from the initiation of the transient to where V  
at 50 percent load.  
has returned to within 1 precent of V  
OUT  
OUT  
11/ Input step transition time between 2 and 10 microseconds.  
12/ Turn-on delay time mesurement is for either a step application of power at the input or the removal of a ground signal  
from the inhibit pin (pin 1) while power is applied to the input.  
SIZE  
STANDARD  
MICROCIRCUIT DRAWING  
5962-92351  
A
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
7
DSCC FORM 2234  
APR 97  
Case outline X.  
Millimeters  
Inches  
Symbol  
A
B  
D
eA  
e1  
e2  
e3  
e4  
E
Min  
Max  
8.38  
0.89  
Min  
Max  
.330  
.035  
1.455  
.805  
.510  
.710  
.910  
1.110  
1.125  
.270  
.100  
.210  
0.64  
36.70  
20.19  
12.70  
17.78  
22.86  
27.94  
28.32  
6.35  
.025  
1.445  
.795  
.500  
.700  
.900  
1.100  
1.115  
.250  
.080  
.200  
36.96  
20.45  
12.95  
18.03  
23.11  
28.19  
28.58  
6.86  
L
R1  
S
2.03  
5.08  
2.54  
5.33  
NOTES:  
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound  
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-  
pound units shall rule.  
2. Case outline X weight: 30 grams maximum.  
FIGURE 1. Case outlines.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
8
DSCC FORM 2234  
APR 97  
Case outline Z.  
Millimeters  
Inches  
Symbol  
A
B  
B1  
D
D1  
D2  
e1  
e2  
e3  
e4  
E
eA  
eB  
F
Min  
Max  
8.38  
0.89  
Min  
Max  
.330  
.035  
.109  
1.455  
1.910  
1.710  
.310  
.510  
.710  
.910  
1.125  
.810  
.930  
.060  
.270  
.110  
.135  
.100  
.210  
0.64  
2.51  
36.70  
48.01  
42.93  
7.37  
12.45  
17.53  
22.61  
28.32  
20.07  
23.11  
1.22  
.025  
.099  
1.445  
1.890  
1.690  
.290  
.490  
.690  
.890  
1.115  
.790  
.910  
.048  
.250  
.090  
.115  
.080  
.200  
2.77  
36.96  
48.51  
43.43  
7.87  
12.95  
18.03  
23.11  
28.58  
20.57  
23.62  
1.52  
L
6.35  
2.29  
2.92  
2.03  
6.86  
2.79  
3.43  
2.54  
R1  
R2  
R3  
S
5.08  
5.33  
NOTES:  
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound  
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-  
pound units shall rule.  
2. Case outline Z weight: 38 grams maximum.  
FIGURE 1. Case outlines - Continued.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
9
DSCC FORM 2234  
APR 97  
Device type  
01  
Case outlines  
X and Z  
Terminal number  
Terminal symbol  
Inhibit input  
Positive output  
Output return  
Negative output  
No connection  
Case ground  
Input return  
Input  
1
2
3
4
5
6
7
8
FIGURE 2. Terminal connections.  
SIZE  
STANDARD  
MICROCIRCUIT DRAWING  
5962-92351  
A
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
10  
DSCC FORM 2234  
APR 97  
TABLE II. Electrical test requirements.  
MIL-PRF-38534 test requirements  
Subgroups  
(in accordance with  
MIL-PRF-38534, group A  
test table)  
Interim electrical parameters  
Final electrical parameters  
Group A test requirements  
---  
1*, 2, 3, 4, 5, 6  
1, 2, 3, 4, 5, 6  
1, 2, 3, 4  
Group C end-point electrical  
parameters 1/  
End-point electrical parameters for  
Radiation Hardness Assurance  
(RHA) devices  
Not Applicable  
* PDA applies to subgroup 1.  
1/ As a minimum, for all Group C testing performed after December 1, 2011  
manufacturers shall perform subgroups 1, 2, and 3 from the Group A  
electrical test table (Table C-Xa of MIL-PRF-38534).  
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:  
a. Burn-in test, method 1015 of MIL-STD-883.  
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level  
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.  
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance  
with the intent specified in method 1015 of MIL-STD-883.  
(2) T as specified in accordance with table I of method 1015 of MIL-STD-883.  
A
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter  
tests prior to burn-in are optional at the discretion of the manufacturer.  
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance  
with MIL-PRF-38534 and as specified herein.  
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:  
a. Tests shall be as specified in table II herein.  
b. Subgroups 7, 8, 9, 10, and 11 shall be omitted.  
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
11  
DSCC FORM 2234  
APR 97  
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:  
a. End-point electrical parameters shall be as specified in table II herein.  
b. Steady-state life test, method 1005 of MIL-STD-883.  
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level  
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.  
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance  
with the intent specified in method 1005 of MIL-STD-883.  
(2) T as specified in accordance with table I of method 1005 of MIL-STD-883.  
A
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.  
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.  
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.  
5. PACKAGING  
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.  
6. NOTES  
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications  
(original equipment), design applications, and logistics purposes.  
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-  
prepared specification or drawing.  
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-  
38534.  
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires  
configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used  
for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962)  
should contact DLA Land and Maritime-VA, telephone (614) 692-0547.  
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,  
or telephone (614) 692-1081.  
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-  
103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have  
agreed to this drawing.  
SIZE  
STANDARD  
5962-92351  
A
MICROCIRCUIT DRAWING  
REVISION LEVEL  
SHEET  
DLA LAND AND MARITIME  
COLUMBUS, OHIO 43218-3990  
C
12  
DSCC FORM 2234  
APR 97  
STANDARD MICROCIRCUIT DRAWING BULLETIN  
DATE: 11-12-01  
Approved sources of supply for SMD 5962-92351are listed below for immediate acquisition information only and  
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be  
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a  
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information  
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime  
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/  
Standard  
microcircuit drawing  
PIN 1/  
Vendor  
CAGE  
number  
Vendor  
similar  
PIN 2/  
5962-9235101HXA  
5962-9235101HXC  
52467  
52467  
AHF2815D/CH  
AHF2815D/CH  
5962-9235101HZA  
5962-9235101HZC  
52467  
52467  
AHF2815DF/CH  
AHF2815DF/CH  
1/ The lead finish shown for each PIN representing  
a hermetic package is the most readily available  
from the manufacturer listed for that part. If the  
desired lead finish is not listed contact the Vendor  
to determine its availability.  
2/ Caution. Do not use this number for item  
acquisition. Items acquired to this number may not  
satisfy the performance requirements of this drawing.  
Vendor CAGE  
number  
Vendor name  
and address  
52467  
International Rectifier Corporation  
2520 Junction Avenue  
San Jose, CA 95134  
The information contained herein is disseminated for convenience only and the  
Government assumes no liability whatsoever for any inaccuracies in the  
information bulletin.  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明