ICE3A4565I [INFINEON]
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD;型号: | ICE3A4565I |
厂家: | Infineon |
描述: | Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD 局域网 开关 |
文件: | 总28页 (文件大小:1319K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Preliminary Datasheet V1.2, 21 May 2004
CoolSET™-F3
ICE3A(B)0365/0565/1065/1565
ICE3A(B)2065/2565
ICE3A(B)3065I/4065I/4565I
ICE3A(B)6065I/6565I
ICE3A(B)3065P/4065P/4565P
ICE3A(B)6065P/6565P
Off-Line SMPS Current Mode
Controller with integrated 650V
Startup Cell/CoolMOS™
Power Management & Supply
N e v e r s t o p t h i n k i n g .
CoolSET™-F3
Revision History:
2004-05-21
Preliminary Datasheet
Previous Version:
Page
Subjects (major changes since last revision)
For questions on technology, delivery and prices please contact the Infineon Technologies Offices in Germany or
the Infineon Technologies Companies and Representatives worldwide: see our webpage at http://
www.infineon.com
CoolMOS™, CoolSET™ are trademarks of Infineon Technologies AG.
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
mcdocu.comments@infineon.com
Edition 2004-05-21
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München
© Infineon Technologies AG 1999.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted char-
acteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest Infin-
eon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address list).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
CoolSET™-F3
Preliminary Data
Off-Line SMPS Current Mode Controller
with integrated 650V Startup Cell/
CoolMOS™
Product Highlights
PG-DIP-8-6
•
•
•
Best in class in DIP8, TO220, I2Pak packages
Leadfree for DIP8 package
Active Burst Mode to reach the lowest Standby Power
Requirements < 100mW
P-TO220-6-46
•
•
Protection features (Auto Restart Mode) to increase
robustness and safety of the system
Adjustable Blanking Window for high load jumps to
increase system reliability
Isolated drain package for TO220/I2PAK
Increased creepage distance for TO220/I2PAK
Wide power class of products for various applications
P-TO220-6-47
•
•
•
Description
Features
The new generation CoolSET™-F3 provides Active Burst
Mode to reach the lowest Standby Power Requirements
<100mW at no load. As the controller is always active
during Active Burst Mode, there is an immediate response
on load jumps without any black out in the SMPS. In Active
Burst Mode the ripple of the output voltage can be reduced
<1%. Furthermore, to increase the robustness and safety
of the system, the device enters into Auto Restart Mode in
the cases of Overtemperature, VCC Overvoltage, Output
Open Loop or Overload and VCC Undervoltage. By means
of the internal precise peak current limitation, the
dimension of the transformer and the secondary diode can
be lowered which leads to more cost efficiency. An
adjustable blanking window prevents the IC from entering
Auto Restart or Active Burst Mode unintentionally during
high load jumps. The CoolSET™-F3 family consists a wide
power class range of products for various applications.
•
650V avalanche rugged CoolMOS™ with built in
switchable Startup Cell
•
Active Burst Mode for lowest Standby Power
@ light load controlled by Feedback signal
Fast load jump response in Active Burst Mode
67/100 kHz fixed switching frequency
Auto Restart Mode for Overtemperature Detection
Auto Restart Mode for Overvoltage Detection
Auto Restart Mode for Overload and Open Loop
Auto Restart Mode for VCC Undervoltage
Blanking Window for short duration high current
User defined Soft Start
Minimum of external components required
Max Duty Cycle 72%
Overall tolerance of Current Limiting < ±5%
Internal PWM Leading Edge Blanking
Soft switching for low EMI
•
•
•
•
•
•
•
•
•
•
•
•
•
Typical Application
+
Converter
Snubber
CBulk
DC Output
85 ... 270 VAC
-
CVCC
Startup Cell
VCC
Drain
Power Management
PWM Controller
Current Mode
Depl-CoolMOS™
CS
FB
Precise Low Tolerance Peak
Current Limitation
RSense
Active Burst Mode
Auto Restart Mode
Control
Unit
GND
SoftS
CSoftS
CoolSET™-F3
Preliminary Datasheet V1.2
3
21 May 2004
CoolSET™-F3
Ordering Codes
1)
Type
Ordering Code
Package
VDS
FOSC
RDSon
230VAC ±15%2)
85-265 VAC2)
10W
ICE3A0365
ICE3A0565
ICE3A1065
ICE3A1565
ICE3A2065
ICE3A2565
Q67040-S4666-A101
Q67040-S4665-A101
Q67040-S4664-A101
Q67040-S4663-A101
Q67040-S4662-A101
Q67040-S4667-A101
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
650V
650V
650V
650V
650V
650V
100kHz
100kHz
100kHz
100kHz
100kHz
100kHz
6.45
4.70
2.95
1.70
0.92
0.65
22W
25W
32W
42W
57W
68W
12W
16W
20W
28W
33W
ICE3B0365
ICE3B0565
ICE3B1065
ICE3B1565
ICE3B2065
Q67040-S4636-A102
Q67040-S4638-A102
Q67040-S4669-A101
Q67040-S4670-A101
Q67040-S4671-A101
Q67040-S4668-A101
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
PG-DIP-8-6
650V
650V
650V
650V
650V
650V
67kHz
67kHz
67kHz
67kHz
67kHz
67kHz
6.45
4.70
2.95
1.70
0.92
0.65
22W
25W
32W
42W
57W
68W
10W
12W
16W
20W
28W
33W
ICE3B2565
1)
typ @ T=25°C
Maximum input power rating at Ta=75°C, Tj=125°C and with copper area on PCB = 6cm².
2)
1)
Type
Ordering Code
Package
VDS
FOSC
RDSon
3.00
2.10
1.55
0.95
0.79
230VAC ±15%2)
125W
85-265 VAC2)
60W
ICE3A3065I
ICE3A4065I
ICE3A4565I
ICE3A6065I
ICE3A6565I
P-TO-220-6-46 650V
P-TO-220-6-46 650V
P-TO-220-6-46 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
100kHz
100kHz
100kHz
100kHz
100kHz
150W
72W
170W
83W
220W
105W
240W
120W
ICE3B3065I
ICE3B4065I
ICE3B4565I
ICE3B6065I
ICE3B6565I
P-TO-220-6-46 650V
P-TO-220-6-46 650V
P-TO-220-6-46 650V
P-TO-220-6-46 650V
P-TO-220-6-46 650V
67kHz
67kHz
67kHz
67kHz
67kHz
3.00
2.10
1.55
0.95
0.79
125W
150W
170W
220W
240W
60W
72W
83W
105W
120W
ICE3A3065P
ICE3A4065P
ICE3A4565P
ICE3A6065P
ICE3A6565P
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
100kHz
100kHz
100kHz
100kHz
100kHz
3.00
2.10
1.55
0.95
0.79
125W
150W
170W
220W
240W
60W
72W
83W
105W
120W
ICE3B3065P
ICE3B4065P
ICE3B4565P
ICE3B6065P
ICE3B6565P
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
P-TO-220-6-47 650V
67kHz
67kHz
67kHz
67kHz
67kHz
3.00
2.10
1.55
0.95
0.79
125W
150W
170W
220W
240W
60W
72W
83W
105W
120W
1)
typ @ T=25°C
Maximum practical continuous input power in an open frame design at Ta=75°C, Tj=125°C and Rth=2.7K/W.
2)
Preliminary Datasheet V1.2
4
21 May 2004
CoolSET™-F3
Page
Preliminary Data
Table of Contents
1
Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pin Configuration with PG-DIP-8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pin Configuration with P-TO220-6-46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pin Configuration with P-TO220-6-47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.1
1.2
1.3
1.4
2
Representative Blockdiagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3
3.1
3.2
3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Startup Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
PWM Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
PWM-Latch FF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Leading Edge Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Propagation Delay Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Adjustable Blanking Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Active Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Entering Active Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Working in Active Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Leaving Active Burst Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Protection Mode (Auto Restart Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.4
3.4.1
3.4.2
3.4.3
3.5
3.5.1
3.5.2
3.6
3.6.1
3.6.2
3.6.2.1
3.6.2.2
3.6.2.3
3.6.3
4
4.1
4.2
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Supply Section 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Supply Section 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Internal Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PWM Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Current Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
CoolMOS™ Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
5
Outline Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Preliminary Datasheet V1.2
5
21 May 2004
CoolSET™-F3
Pin Configuration and Functionality
Preliminary Data
1
Pin Configuration and Functionality
1.2 Pin Configuration with P-TO220-6-46
1.1
Pin Configuration with PG-DIP-8-6
Pin
1
Symbol Function
Pin
Symbol Function
650V1) Depl-CoolMOS™ Drain
Drain
1
2
3
SoftS
FB
Soft-Start
Feedback
3
CS
Current Sense/
650V1) Depl-CoolMOS™ Source
CS
Current Sense/
650V1) Depl-CoolMOS™ Source
4
5
6
7
GND
VCC
SoftS
FB
Controller Ground
Controller Supply Voltage
Soft-Start
650V1) Depl-CoolMOS™ Drain
650V1) Depl-CoolMOS™ Drain
4
5
Drain
Drain
Feedback
6
7
N.C.
VCC
GND
Not Connected
1)
Controller Supply Voltage
Controller Ground
at Tj = 110°C
8
1)
at Tj = 110°C
Package P-TO220-6-46
Package PG-DIP-8-6
SoftS
FB
1
8
7
6
5
GND
VCC
N.C
1
2
3
4
5
6
7
2
CS
3
4
Drain
Drain
Figure 1
Note: Pin
package.
Pin Configuration PG-DIP-8-6(top view)
Figure 2 Pin Configuration P-TO220-6-46(top view)
4
and are shorted within the DIP
5
Preliminary Datasheet V1.2
6
21 May 2004
CoolSET™-F3
Preliminary Data
Pin Configuration and Functionality
1.3 Pin Configuration with P-TO220-6-47
1.4
Pin Functionality
SoftS (Soft Start & Auto Restart Control)
The SoftS pin combines the functions of Soft Start
during Start Up and error detection for Auto Restart
Mode. These functions are implemented and can be
adjusted by means of an external capacitor at SoftS to
ground. This capacitor also provides an adjustable
blanking window for high load jumps, before the IC
enters into Auto Restart Mode.
Pin
1
Symbol Function
650V1) Depl-CoolMOS™ Drain
Drain
3
CS
Current Sense/
650V1) Depl-CoolMOS™ Source
4
5
6
7
GND
VCC
SoftS
FB
Controller Ground
Controller Supply Voltage
Soft-Start
FB (Feedback)
The information about the regulation is provided by the
FB Pin to the internal Protection Unit and to the internal
PWM-Comparator to control the duty cycle. The FB-
Signal controls in case of light load the Active Burst
Mode of the controller.
Feedback
1)
at Tj = 110°C
CS (Current Sense)
The Current Sense pin senses the voltage developed
on the series resistor inserted in the source of the
integrated Depl-CoolMOS™. If CS reaches the internal
threshold of the Current Limit Comparator, the Driver
output is immediately switched off. Furthermore the
current information is provided for the PWM-
Comparator to realize the Current Mode.
Package P-TO220-6-47
Drain (Drain of integrated Depl-CoolMOS™)
Pin Drain is the connection to the Drain of the internal
Depl-CoolMOSTM
.
VCC (Power supply)
The VCC pin is the positive supply of the IC. The
operating range is between 8.5V and 21V.
GND (Ground)
1
2
3
4
5
6
7
The GND pin is the ground of the controller.
Figure 3 Pin Configuration P-TO220-6-47(top view)
Preliminary Datasheet V1.2
7
21 May 2004
CoolSET™-F3
Preliminary Data
Representative Blockdiagram
2
Representative Blockdiagram
s
n
2
f
Figure 4
Representative Blockdiagram
Preliminary Datasheet V1.2
8
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
3.2
Power Management
3
Functional Description
All values which are used in the functional description
are typical values. For calculating the worst cases the
min/max values which can be found in section 4
Electrical Characteristics have to be considered.
VCC
Drain
Startup Cell
3.1
Introduction
CoolSET™-F3 is the further development of the
CoolSET™-F2 to meet the requirements for the lowest
Standby Power at minimum load and no load
conditions. A new fully integrated Standby Power
concept is implemented into the IC in order to keep the
application design easy. Compared to CoolSET™-F2
no further external parts are needed to achieve the
lowest Standby Power. An intelligent Active Burst
Mode is used for this Standby Mode. After entering this
mode there is still a full control of the power conversion
by the secondary side via the same optocoupler that is
used for the normal PWM control. The response on
load jumps is optimized. The voltage ripple on Vout is
minimized. Vout is further on well controlled in this
mode.
Depl-CoolMOS™
Power Management
Undervoltage Lockout
15V
Internal Bias
8.5V
6.5V
Voltage
Reference
Auto Restart Mode
Active Burst Mode
The usually external connected RC-filter in the
feedback line after the optocoupler is integrated in the
IC to reduce the external part count.
T1
Furthermore a high voltage Startup Cell is integrated
into the IC which is switched off once the Undervoltage
Lockout on-threshold of 15V is exceeded. This Startup
Cell is part of the integrated Depl-CoolMOS™. The
external startup resistor is no longer necessary as this
Startup Cell is connected to the Drain. Power losses
are therefore reduced. This increases the efficiency
under light load conditions drastically.
SoftS
Power Management
Figure 5
The Undervoltage Lockout monitors the external
supply voltage VVCC. When the SMPS is plugged to the
main line the internal Startup Cell is biased and starts
to charge the external capacitor CVCC which is
connected to the VCC pin. This VCC charge current
which is provided by the Startup Cell from the Drain pin
is 1.05mA. When VVCC exceeds the on-threshold
VCCon=15V the internal voltage reference and bias
circuit are switched on. Then the Startup Cell is
switched off by the Undervoltage Lockout and therefore
no power losses present due to the connection of the
Startup Cell to the Drain voltage. To avoid uncontrolled
ringing at switch-on a hysteresis is implemented. The
switch-off of the controller can only take place after
Active Mode was entered and VVCC falls below 8.5V.
The Soft-Start capacitor is also used for providing an
adjustable blanking window for high load jumps. During
this time window the overload detection is disabled.
With this concept no further external components are
necessary to adjust the blanking window.
An Auto Restart Mode is implemented in the IC to
reduce the average power conversion in the event of
malfunction or unsafe operating condition in the SMPS
system. This feature increases the system’s
robustness and safety which would otherwise lead to a
destruction of the SMPS. Once the malfunction is
removed, normal operation is automatically initiated
after the next Start Up Phase.
The maximum current consumption before the
controller is activated is about 160µA.
The internal precise peak current limitation reduces the
costs for the transformer and the secondary diode. The
influence of the change in the input voltage on the
power limitation can be avoided together with the
When VVCC falls below the off-threshold VCCoff=8.5V the
internal reference is switched off and the Power Down
reset let T1 discharging the soft-start capacitor CSoftS at
pin SoftS. Thus it is ensured that at every startup cycle
the voltage ramp at pin SoftS starts at zero.
integrated
Propagation
Delay
Compensation.
Therefore the maximum power is nearly independent
on the input voltage which is required for wide range
SMPS. There is no need for an extra over-sizing of the
SMPS, e.g. the transformer or the secondary diode.
The internal Voltage Reference is switched off if Auto
Restart Mode is entered. The current consumption is
then reduced to 300µA.
Preliminary Datasheet V1.2
9
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
Once the malfunction condition is removed, this block maximum charge current in the very first stage when
will then turn back on. The recovery from Auto Restart VSoftS is below 1V, is limited to 1.32mA.
Mode does not require disconnecting the SMPS from
the AC line
When Active Burst Mode is entered, the internal Bias is
switched off in order to reduce the current consumption
VSoftS
to below 1.05mA while keeping the Voltage Reference
active as this is necessary in this mode.
max. Startup Phase
5.4V
4V
3.3
Startup Phase
1V
max. Soft Start Phase
6.5V
3.25k
DCmax
t
R
T2
SoftS
DC
1
T3
1V
DC
2
SoftS
C
SoftS
Soft Start
Soft-Start
t1
t2 t
Comparator
Gate Driver
C7
&
Figure 7
Startup Phase
G7
By means of this extra charge stage, there is no delay
in the beginning of the Startup Phase when there is still
no switching. Furthermore Soft Start is finished at 4V to
have faster the maximum power capability. The duty
cycles DC1 and DC2 are depending on the mains and
the primary inductance of the transformer. The
limitation of the primary current by DC2 is related to
VSoftS = 4V. But DC1 is related to a maximum primary
current which is limited by the internal Current Limiting
with CS = 1V. Therefore the maximum Startup Phase
is divided into a Soft Start Phase until t1 and a phase
from t1 until t2 where maximum power is provided if
demanded by the FB signal.
C2
4V
0.85V
CS
x3.7
PWM OP
Soft Start
Figure 6
At the beginning of the Startup Phase, the IC provides
a Soft Start duration whereby it controls the maximum
primary current by means of a duty cycle limitation. A
signal VSoftS which is generated by the external
capacitor CSofts in combination with the internal pull up
resistor RSoftS, determines the duty cycle until VSoftS
exceeds 4V.
When the Soft Start begins, CSoftS is immediately
charged up to approx. 1V by T2. Therefore the Soft
Start Phase takes place between 1V and 4V. Above
VSoftsS = 4V there is no longer duty cycle limitation
DCmax which is controlled by comparator C7 since
comparator C2 blocks the gate G7 (see Figure 6). This
Preliminary Datasheet V1.2
10
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
3.4.3
Gate Driver
3.4
PWM Section
0.72
PWM Section
Oscillator
Duty Cycle
max
VCC
PWM-Latch
Clock
1
Gate
Soft Start
FF1
Comparator
CoolMOS™
Gate Driver
&
S
R
1
PWM
Comparator
Q
G8
G9
Gate Driver
Current
Limiting
Figure 9
Gate Driver
The driver-stage is optimized to minimize EMI and to
provide high circuit efficiency. This is done by reducing
the switch on slope when exceeding the internal
CoolMOS™ threshold. This is achieved by a slope
control of the rising edge at the driver’s output (see
Figure 10).
Gate
Figure 8
3.4.1
PWM Section
Oscillator
The oscillator generates
switching frequency of ICE3Axx65x is fOSC = 100kHz
and for ICE3Bxx65x fOSC 67kHz. resistor, a
a fixed frequency. The
(internal) VGate
=
A
capacitor and a current source and current sink which
determine the frequency are integrated. The charging
and discharging current of the implemented oscillator
capacitor are internally trimmed, in order to achieve a
very accurate switching frequency. The ratio of
controlled charge to discharge current is adjusted to
reach a maximum duty cycle limitation of Dmax=0.72.
ca. t = 130ns
5V
t
3.4.2
PWM-Latch FF1
The oscillator clock output provides a set pulse to the
PWM-Latch when initiating the external Power Switch
conduction. After setting the PWM-Latch can be reset
by the PWM comparator, the Soft Start comparator or
the Current-Limit comparator. In case of resetting, the
driver is shut down immediately.
Figure 10
Gate Rising Slope
Thus the leading switch on spike is minimized. When
the integrated CoolMOS™ is switched off, the falling
shape of the driver is slowed down when reaching 2V
to prevent an overshoot below ground. Furthermore the
driver circuit is designed to eliminate cross conduction
of the output stage. During powerup when VCC is
below the undervoltage lockout threshold VVCCoff, the
output of the Gate Driver is low to disable power
transfer to the seconding side.
Preliminary Datasheet V1.2
11
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
3.5.1
Leading Edge Blanking
3.5
Current Limiting
VSense
PWM Latch
FF1
V
csth
tLEB = 220ns
Current Limiting
Propagation-Delay
Compensation
Vcsth
Leading
Edge
C10
C12
Blanking
220ns
t
PWM-OP
&
Figure 12
Leading Edge Blanking
G10
Each time when the external Power Switch is switched
on, a leading edge spike is generated due to the
primary-side capacitances and secondary-side rectifier
reverse recovery time. This spike can cause the gate
drive to switch off unintentionally. To avoid a premature
termination of the switching pulse, this spike is blanked
out with a time constant of tLEB = 220ns. During this
time, the gate drive will not be switched off.
0.257V
1pF
10k
Active Burst
Mode
D1
CS
Current Limiting Block
3.5.2
Propagation Delay Compensation
In case of overcurrent detection, the switch-off of the
external Power Switch is delayed due to the
propagation delay of the circuit. This delay causes an
overshoot of the peak current Ipeak which depends on
the ratio of dI/dt of the peak current (see Figure 13).
Figure 11
There is a cycle by cycle Current Limiting realized by
the Current-Limit comparator C10 to provide an
overcurrent detection. The source current of the
external Power Switch is sensed via an external sense
resistor RSense . By means of RSense the source current
is transformed to a sense voltage VSense which is fed
into the pin CS. If the voltage VSense exceeds the
internal threshold voltage Vcsth the comparator C10
immediately turns off the gate drive by resetting the
PWM Latch FF1. A Propagation Delay Compensation
is added to support the immediate shut down without
delay of the Power Switch in case of Current Limiting.
The influence of the AC input voltage on the maximum
output power can thereby be avoided.
Signal1
IOvershoot2
Signal2
tPropagation Delay
ISense
Ipeak2
Ipeak1
ILimit
IOvershoot1
To prevent the Current Limiting from distortions caused
by leading edge spikes a Leading Edge Blanking is
integrated in the current sense path for the
comparators C10, C12 and the PWM-OP.
t
Figure 13
Current Limiting
The output of comparator C12 is activated by the Gate
G10 if Active Burst Mode is entered. Once activated the
current limiting is thereby reduced to 0.257V. This
voltage level determines the power level when the
Active Burst Mode is left if there is a higher power
demand.
The overshoot of Signal2 is bigger than of Signal1 due
to the steeper rising waveform. This change in the
slope is depending on the AC input voltage.
Propagation Delay Compensation is integrated to limit
the overshoot dependency on dI/dt of the rising primary
current. That means the propagation delay time
between exceeding the current sense threshold Vcsth
and the switch off of the external Power Switch is
compensated over temperature within a wide range.
Preliminary Datasheet V1.2
12
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
Current Limiting is now possible in a very accurate way.
3.6
Control Unit
E.g. Ipeak = 0.5A with RSense = 2. Without Propagation
Delay Compensation the current sense threshold is set
to a static voltage level Vcsth=1V. A current ramp of
dI/dt = 0.4A/µs, that means dVSense/dt = 0.8V/µs, and a
The Control Unit contains the functions for Active Burst
Mode and Auto Restart Mode. The Active Burst Mode
and the Auto Restart Mode are combined with an
Adjustable Blanking Window which is depending on the
external Soft Start capacitor. By means of this
Adjustable Blanking Window, the IC avoids entering
into these two modes accidentally. Furthermore it also
provides a certain time whereby the overload detection
is delayed. This delay is useful for applications which
normally works with a low current and occasionally
require a short duration of high current.
propagation delay time of i.e. tPropagation
=180ns
Delay
leads then to an Ipeak overshoot of 12%. By means of
propagation delay compensation the overshoot is only
about 2% (see Figure 14).
with compensation
without compensation
V
1,3
1,25
1,2
3.6.1
Adjustable Blanking Window
1,15
1,1
SoftS
1,05
1
6.5V
0,95
0,9
RSoftS
5k
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
V
dVSense
dt
µs
4.4V
1
S1
Figure 14
Overcurrent Shutdown
G2
The Propagation Delay Compensation is realized by
means of a dynamic threshold voltage Vcsth (see Figure
15). In case of a steeper slope the switch off of the
driver is earlier to compensate the delay.
C3
VOSC
5.4V
max. Duty Cycle
Auto
&
G5
4.8V
Restart
Mode
C4
off time
Active
Burst
Mode
VSense
Vcsth
t
Propagation Delay
&
FB
G6
C5
1.32V
Signal1
Signal2
Control Unit
t
Figure 15
Dynamic Voltage Threshold Vcsth
Figure 16
Adjustable Blanking Window
VSoftS is clamped at 4.4V by the closed switch S1 after
the SMPS is settled. If overload occurs VFB is
exceeding 4.8V. Auto Restart Mode can’t be entered as
the gate G5 is still blocked by the comparator C3. But
after VFB has exceeded 4.8V the switch S1 is opened
Preliminary Datasheet V1.2
13
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
via the gate G2. The external Soft Start capacitor can The Active Burst Mode is located in the Control Unit.
now be charged further by the integrated pull up Figure 17 shows the related components.
resistor RSoftS. The comparator C3 releases the gates
G5 and G6 once VSofts has exceeded 5.4V. Therefore 3.6.2.1
Entering Active Burst Mode
there is no entering of Auto Restart Mode possible
The FB signal is always observed by the comparator
C5 if the voltage level falls below 1.32V. In that case the
switch S1 is released which allows the capacitor CSoftS
to be charged starting from the clamped voltage level
at 4.4V in normal operating mode. If VSoftS exceeds
5.4V the comparator C3 releases the gate G6 to enter
the Active Burst Mode. The time window that is
generated by combining the FB and SoftS signals with
gate G6 avoids a sudden entering of the Active Burst
Mode due to large load jumps. This time window can be
during this charging time of the external capacitor
SoftS. The same procedure happens to the external
C
Soft Start capacitor if a low load condition is detected
by comparator C5 when VFB is falling below 1.32V.
Only after VSoftS has exceeded 5.4V and VFB is still
below 1.32V Active Burst Mode is entered.
3.6.2
The controller provides Active Burst Mode for low load
conditions at VOUT Active Burst Mode increases
Active Burst Mode
adjusted by the external capacitor CSoftS
.
.
significantly the efficiency at light load conditions while
supporting a low ripple on VOUT and fast response on
load jumps. During Active Burst Mode which is
controlled only by the FB signal the IC is always active
and can therefore immediately response on fast
changes at the FB signal. The Startup Cell is kept
switched off to avoid increased power losses for the
self supply.
After entering Active Burst Mode a burst flag is set and
the internal bias is switched off in order to reduce the
current consumption of the IC down to approx. 1.05mA.
In this Off State Phase the IC is no longer self supplied
so that therefore CVCC has to provide the VCC current
(see Figure 18). Furthermore gate G11 is then released
to start the next burst cycle once VFB has 3.4V
exceeded.
It has to be ensured by the application that the VCC
remains above the Undervoltage Lockout Level of 8.5V
to avoid that the Startup Cell is accidentally switched
on. Otherwise power losses are significantly increased.
The minimum VCC level during Active Burst Mode is
depending on the load conditions and the application.
The lowest VCC level is reached at no load conditions
SoftS
6.5V
RSoftS
5k?
Internal Bias
4.4V
at VOUT
.
3.6.2.2
Working in Active Burst Mode
S1
Current
After entering the Active Burst Mode the FB voltage
rises as VOUT starts to decrease due to the inactive
PWM section. Comparator C6a observes the FB signal
if the voltage level 4V is exceeded. In that case the
internal circuit is again activated by the internal Bias to
start with switching. As now in Active Burst Mode the
gate G10 is released the current limit is only 0.257V to
reduce the conduction losses and to avoid audible
noise. If the load at VOUT is still below the starting level
for the Active Burst Mode the FB signal decreases
down to 3.4V. At this level C6b deactivates again the
internal circuit by switching off the internal Bias. The
gate G11 is released as after entering Active Burst
Mode the burst flag is set. If working in Active Burst
Mode the FB voltage is changing like a saw tooth
between 3.4V and 4V (see Figure 18).
Limiting
&
C3
G10
5.4V
4.8V
C4
Active
Burst
C5
&
G6
Mode
FB
1.32V
4.0V
3.4V
C6a
C6b
3.6.2.3
Leaving Active Burst Mode
&
The FB voltage immediately increases if there is a high
load jump. This is observed by comparator C4. As the
current limit is ca. 26% during Active Burst Mode a
certain load jump is needed that FB can exceed 4.8V.
At this time C4 resets the Active Burst Mode which also
G11
Control Unit
Figure 17
Active Burst Mode
Preliminary Datasheet V1.2
14
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
blocks C12 by the gate G10. Maximum current can now 3.6.3
Protection Mode (Auto Restart Mode)
be provided to stabilize VOUT
.
In order to increase the SMPS system’s robustness
and safety, the IC provides the Auto Restart Mode as a
protection feature. The Auto Restart Mode is entered
upon detection of the following faults in the system:
V
FB
Entering Active
Burst Mode
Leaving Active
Burst Mode
•
•
•
•
•
•
VCC Overvoltage
Overtemperature
Overload
Open Loop
VCC Undervoltage
Short Optocoupler
4.80V
4.00V
3.40V
1.32V
VSoftS
t
Blanking Window
SoftS
6.5V
Control Unit
RSoftS
5.40V
CSoftS
5k
VCC
4.40V
C1
&
G1
4.4V
Spike
17V
Blanking
VCS
t
t
t
t
t
8.0us
C11
4.0V
Thermal Shutdown
T >140°C
j
Current limit level during
Active Burst Mode
1.00V
S1
0.257V
4.8V
5.4V
&
Auto Restart
Mode
C4
C3
FB
V
G5
VCC
Voltage
Reference
8.5V
Figure 19
Auto Restart Mode
The VCC voltage is observed by comparator C1 if 17V
is exceeded. The output of C1 is combined with both
the output of C11 which checks for SoftS<4.0V, and the
output of C4 which checks for FB>4.8V. Therefore the
overvoltage detection is can only active during Soft
Start Phase(SoftS<4.0V) and when FB signal is
outside the operating range > 4.8V. Therefore any
small voltage overshoots of VVCC during normal
operating cannot trigger the Auto Restart Mode.
IVCC
7.2mA
1.05mA
VOUT
In order to ensure system reliability and prevent any
false activation, a blanking time is implemented before
the IC can enter into the Auto Restart Mode. The output
of the VCC overvoltage detection is fed into a spike
blanking with a time constant of 8.0µs.
Max. Ripple < 1%
The other fault detection which can result in the Auto
Restart Mode and has this 8.0µs blanking time is the
Overtemperature detection. This block checks for a
junction temperature of higher than 140°C for
malfunction operation.
Figure 18
Signals in Active Burst Mode
Preliminary Datasheet V1.2
15
21 May 2004
CoolSET™-F3
Preliminary Data
Functional Description
Once the Auto Restart Mode is entered, the internal
Voltage Reference is switched off in order to reduce the
current consumption of the IC as much as possible. In
this mode, the average current consumption is only
300µA as the only working block is the Undervoltage
Lockout(UVLO) which controls the Startup Cell by
switching on/off at VVCCon/VVCCoff
.
As there is no longer a self supply by the auxiliary
winding, VCC starts to drop. The UVLO switches on the
integrated Startup Cell when VCC falls below 8.5V. It
will continue to charge VCC up to 15V whereby it is
switched off again and the IC enters into the Start Up
Phase.
As long as all fault conditions have been removed, the
IC will automatically power up as usual with switching
cycle at the GATE output after Soft Start duration. Thus
the name Auto Restart Mode.
Other fault detections which are active in normal
operation is the sensing for Overload, Open Loop and
VCC undervoltage conditions. In the first 2 cases, FB
will rise above 4.8V which will be observed by C4. At
this time, S1 is released such that VSoftS can rise from
its earlier clamp voltage of 4.4V. If VSoftS exceeds 5.4V
which is observed by C3, Auto Restart Mode is entered
as both inputs of the gate G5 are high.
This charging of the Soft Start capacitor from 4.4V to
5.4V defines a blanking window which prevents the
system from entering into Auto Restart Mode un-
intentionally during large load jumps. In this event, FB
will rise close to 6.5V for a short duration before the
loop regulates with FB less than 4.8V. This is the same
blanking time window as for the Active Burst Mode and
can therefore be adjusted by the external CSoftS
.
In the case of VCC undervoltage, ie. VCC falls below
8.5V, the IC will be turn off with the Startup Cell
charging VCC as described earlier in this section. Once
VCC is charged above 15V, the IC will start a new
startup cycle. The same procedure applies when the
system is under Short Optocoupler fault condition, as it
will lead to VCC undervoltage.
Preliminary Datasheet V1.2
16
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4
Electrical Characteristics
Note: All voltages are measured with respect to ground (Pin 8). The voltage levels are valid if other ratings are
not violated.
4.1
Absolute Maximum Ratings
Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction
of the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 7
(VCC) is discharged before assembling the application circuit.
Parameter
Symbol
Limit Values
Unit
Remarks
min.
max.
Drain Source Voltage
ICE3Axx65/xx65I/xx65P
ICE3Bxx65/xx65I/xx65P
VDS
-
650
V
Tj=110°C
Avalanche energy,
repetitive tAR limited by
max. Tj=150°C1)
ICE3x0365
ICE3x0565
ICE3x1065
ICE3x1565
ICE3x2065
ICE3x2565
EAR1
EAR2
EAR3
EAR4
EAR5
EAR6
-
-
-
-
-
-
-
tbd
mJ
mJ
mJ
mJ
mJ
mJ
mJ
0.01
0.07
tbd
0.40
tbd
ICE3x3065I EAR7
tbd
ICE3x3065P
ICE3x4065I EAR8
ICE3x4065P
-
-
-
-
tbd
tbd
tbd
tbd
mJ
mJ
mJ
mJ
ICE3x4565I EAR9
ICE3x4565P
ICE3x6065I EAR10
ICE3x6065P
ICE3x6565I EAR11
ICE3x6565P
Preliminary Datasheet V1.2
17
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
Parameter
Symbol
Limit Values
Unit
Remarks
min.
max.
0.3
0.5
1
Avalanche current,
repetitive tAR limited by
max. Tj=150°C
ICE3x0365
ICE3x0565
ICE3x1065
ICE3x1565
ICE3x2065
ICE3x2565
IAR1
IAR2
IAR3
IAR4
IAR5
IAR6
-
-
-
-
-
-
-
A
A
A
A
A
A
A
1.5
2
2.5
tbd
ICE3x3065I IAR7
ICE3x3065P
ICE3x4065I IAR8
ICE3x4065P
-
-
-
-
tbd
tbd
tbd
tbd
A
A
A
A
ICE3x4565I IAR9
ICE3x4565P
ICE3x6065I IAR10
ICE3x6065P
ICE3x6565I IAR11
ICE3x6565P
1)
Repetitive avalanche causes additional power losses that can be calculated as PAV=EAR*f
Preliminary Datasheet V1.2
18
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
Parameter
Symbol
Limit Values
Unit
Remarks
min.
max.
Thermal Resistance
Junction-Ambient
ICE3x0365
ICE3x0565
ICE3x1065
ICE3x1565
ICE3x2065
ICE3x2565
RthJA1
90
K/W
PG-DIP-8-6
ICE3x3065I RthJA2
ICE3x4065I
ICE3x4565I
ICE3x6065I
ICE3x6565I
103
82
K/W
K/W
P-TO220-6-46
Free standing without
heatsink
ICE3x3065P RthJA3
ICE3x4065P
ICE3x4565P
P-TO220-6-47
Free standing without
heatsink
ICE3x6065P
ICE3x6565P
Thermal Resistance
Junction-Case
ICE3x3065I RthJC1
ICE3x3065P
3.30
3.08
2.94
2.79
2.75
K/W
K/W
K/W
K/W
K/W
P-TO220-6-46
P-TO220-6-47
ICE3x4065I RthJC2
ICE3x4065P
P-TO220-6-46
P-TO220-6-47
ICE3x4565I RthJC3
ICE3x4565P
P-TO220-6-46
P-TO220-6-47
ICE3x6065I RthJC4
ICE3x6065P
P-TO220-6-46
P-TO220-6-47
ICE3x6565I RthJC5
ICE3x6565P
P-TO220-6-46
P-TO220-6-47
VCC Supply Voltage
FB Voltage
VVCC
VFB
VSoftS
VCS
Tj
-0.3
-0.3
-0.3
-0.3
-40
-55
-
22
V
6.5
6.5
6.5
150
150
3
V
SoftS Voltage
V
CS Voltage
V
Junction Temperature
Storage Temperature
° C
° C
kV
Controller & CoolMOS™
Human body model1)
TS
ESD Capability(incl. Drain Pin)
VESD
1)
According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5kΩ series resistor)
Preliminary Datasheet V1.2
19
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4.2
Operating Range
Note: Within the operating range the IC operates as described in the functional description.
Parameter
Symbol
Limit Values
Unit
Remarks
min.
max.
VCC Supply Voltage
VVCC
VVCCoff
20
V
Junction Temperature of
Controller
TjCon
-25
130
150
°C
° C
Max value limited due to thermal
shut down of controller
Junction Temperature of
CoolMOS™
TjCoolMOS
-25
4.3
Characteristics
4.3.1
Supply Section 1
Note: The electrical characteristics involve the spread of values within the specified supply voltage and junction
temperature range TJ from – 25 ° C to 130 ° C. Typical values represent the median values, which are
related to 25°C. If not otherwise stated, a supply voltage of VCC = 15 V is assumed.
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
Start Up Current
IVCCstart
-
160
220
µA
VVCC =14V
VCC Charge Current
IVCCcharge1 0.55
1.05
0.88
0.2
1.60
-
mA
mA
µA
VVCC = 0V
VVCC =14V
IVCCcharge2
-
-
Leakage Current of
IStartLeak
50
VVCC=16V, VDrain = 450V
at Tj=100°C
Start Up Cell and CoolMOS
Supply Current with
Inactive Gate
IVCCsup1
-
-
5.5
7.0
-
mA
Supply Current in
Auto Restart Mode with
Inactive Gate
IVCCrestart
300
µA
IFB = 0
ISofts = 0
Supply Current in
Active Burst Mode
with Inactive Gate
IVCCburst1
IVCCburst2
-
-
1.05
0.95
1.25
1.15
mA
mA
VVCC =15V
VFB = 3.7V, VSoftS = 4.4V
VVCC = 9.5V
VFB = 3.7V, VSoftS = 4.4V
VCC Turn-On Threshold
VCC Turn-Off Threshold
VCC Turn-On/Off Hysteresis
VVCCon
VVCCoff
VVCChys
14.2
8.0
-
15.0
8.5
6.5
15.8
9.0
-
V
V
V
Preliminary Datasheet V1.2
20
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4.3.2
Supply Section 2
Parameter
Symbol
Limit Values
max.
Unit
Test Condition
min.
typ.
5.3
5.2
5.4
5.4
5.7
5.4
6.1
5.8
6.9
6.2
7.9
6.9
tdb
Supply Current
with Active Gate
ICE3A0365
ICE3B0365
ICE3A0565
ICE3B0565
ICE3A1065
ICE3B1065
ICE3A1565
ICE3B1565
ICE3A2065
ICE3B2065
ICE3A2565
ICE3B2565
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
-
-
-
-
-
-
-
-
-
-
-
-
-
6.8
6.7
6.9
6.9
7.2
6.9
7.6
7.3
8.4
7.7
9.4
8.4
tdb
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
VSoftS = 4.4V
IFB = 0
Supply Current
with Active Gate
ICE3A3065I
ICE3A3065P
VSoftS = 4.4V
IFB = 0
ICE3B3065I
ICE3B3065P
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
IVCCsup2
-
-
-
-
-
-
-
-
-
tdb
tdb
tdb
tdb
tdb
tdb
tdb
tdb
6.8
tdb
tdb
tdb
tdb
tdb
tdb
tdb
tdb
8.3
mA
mA
mA
mA
mA
mA
mA
mA
mA
ICE3A4065I
ICE3A4065P
ICE3B4065I
ICE3B4065P
ICE3A4565I
ICE3A4565P
ICE3B4565I
ICE3B4565P
ICE3A6065I
ICE3A6065P
ICE3B6065I
ICE3B6065P
ICE3A6565I
ICE3A6565P
ICE3B6565I
ICE3B6565P
Preliminary Datasheet V1.2
21
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4.3.3
Internal Voltage Reference
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
6.63
Trimmed Reference Voltage
VREF
6.37
6.50
V
measured at pin FB
IFB = 0
4.3.4
PWM Section
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
92
typ.
100
100
max.
Fixed Oscillator
Frequency
ICE3Axx65
ICE3Axx65I
ICE3Axx65P
fOSC1
fOSC2
108
106
kHz
kHz
94
Tj = 25°C
Tj = 25°C
VFB < 0.3V
Fixed Oscillator
Frequency
ICE3Bxx65
ICE3Bxx65I
ICE3Bxx65P
fOSC1
fOSC2
61
63
67
67
73
71
kHz
kHz
Max. Duty Cycle
Min. Duty Cycle
PWM-OP Gain
Dmax
Dmin
0.67
0
0.72
-
0.77
-
AV
3.5
-
3.7
0.85
0.7
3.9
Voltage Ramp Max Level
VMax-Ramp
VFBmin
-
-
V
V
VFB Operating Range Min Level
0.3
VFB Operating Range Max level
VFBmax
-
-
4.75
V
CS=1V, limited by
Comparator C41)
FB Pull-Up Resistor
SoftS Pull-Up Resistor
1)
RFB
16
39
20
50
27
62
kΩ
kΩ
RSoftS
Design characteristic (not meant for production testing)
Preliminary Datasheet V1.2
22
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4.3.5
Control Unit
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
Deactivation Level for SoftS
Comparator C7 by C2
VSoftSC2
3.85
4.00
4.15
4.57
5.60
-
V
VFB > 5V
Clamped VSoftS Voltage during
Normal Operating Mode
VSoftSclmp 4.23
4.40
5.40
1.3
V
VFB = 4V
Activation Limit of
Comparator C3
VSoftSC3
ISoftSstart
5.20
-
V
VFB > 5V
SoftS Startup Current
mA
V
VSoftS = 0V
VSoftS > 5.6V
VSoftS > 5.6V
Over Load & Open Loop Detection VFBC4
Limit for Comparator C4
4.62
1.23
3.85
3.25
16.1
130
-
4.80
1.30
4.00
3.40
17.1
140
8.0
4.98
1.37
4.15
3.55
18.1
150
-
Active Burst Mode Level for
Comparator C5
VFBC5
VFBC6a
VFBC6b
VVCCOVP
TjSD
V
Active Burst Mode Level for
Comparator C6a
V
After Active Burst
Mode is entered
Active Burst Mode Level for
Comparator C6b
V
After Active Burst
Mode is entered
Overvoltage Detection Limit
Thermal Shutdown1)
Spike Blanking
1)
V
VFB > 5V
VSoftS < 4.0V
°C
µs
tSpike
The parameter is not subject to production test - verified by design/characterization
Note: The trend of all the voltage levels in the Control Unit is the same regarding the deviation except VVCCOVP
and VVCCPD
4.3.6
Current Limiting
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
Peak Current Limitation
(incl. Propagation Delay)
Vcsth
VCS2
tLEB
0.97
1.02
1.07
V
dVsense / dt = 0.6V/µs
(see Figure 15)
Peak Current Limitation during
Active Burst Mode
0.232
-
0.257
220
0.282
V
Leading Edge Blanking
-
ns
µA
VSoftS = 4.4V
VCS =0V
CS Input Bias Current
ICSbias
-1.0
-0.2
0
Preliminary Datasheet V1.2
23
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
4.3.7
CoolMOS™ Section
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
Drain Source Breakdown Voltage
ICE3Axx65/xx65I/xx65P
ICE3Bxx65/xx65I/xx65P
V(BR)DSS
600
650
-
-
-
-
V
V
Tj = 25°C
Tj = 110°C
Drain Source
On-Resistance
ICE3A0365
ICE3B0365
RDSon1
RDSon2
RDSon3
RDSon4
RDSon5
RDSon6
RDSon7
-
-
6.45
12.90
7.50
15.00
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A0565
ICE3B0565
-
-
4.70
9.40
5.44
10.88
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A1065
ICE3B1065
-
-
2.95
5.90
3.42
6.84
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A1565
ICE3B1565
-
-
1.70
3.40
1.96
3.92
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A2065
ICE3B2065
-
-
0.92
1.84
1.05
2.10
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A2565
ICE3B2565
-
-
0.65
1.30
0.75
1.50
Ω
Ω
Tj = 25°C
Tj = 125°C
Drain Source
On-Resistance
ICE3A3065I
ICE3A3065P
ICE3B3065I
ICE3B3065P
-
-
3.00
6.00
3.47
6.94
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A4065I
ICE3A4065P
ICE3B4065I
ICE3B4065P
RDSon8
RDSon9
RDSon10
RDSon11
-
-
2.10
4.20
2.43
4.86
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A4565I
ICE3A4565P
ICE3B4565I
ICE3B4565P
-
-
1.55
3.10
1.80
3.60
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A6065I
ICE3A6065P
ICE3B6065I
ICE3B6065P
0.95
1.90
1.10
2.20
Ω
Ω
Tj = 25°C
Tj = 125°C
ICE3A6565I
ICE3A6565P
ICE3B6565I
ICE3B6565P
-
-
0.79
1.58
0.91
1.82
Ω
Ω
Tj = 25°C
Tj = 125°C
Preliminary Datasheet V1.2
24
21 May 2004
CoolSET™-F3
Preliminary Data
Electrical Characteristics
Parameter
Symbol
Limit Values
Unit
Test Condition
min.
typ.
max.
Effective output
capacitance,
energy related
ICE3A0365
ICE3B0365
Co(er)1
Co(er)2
Co(er)3
Co(er)4
Co(er)5
Co(er)6
Co(er)7
-
3.65
-
-
-
-
-
-
-
pF
pF
pF
pF
pF
pF
pF
VDS = 0V to 480V
ICE3A0565
ICE3B0565
-
-
-
-
-
-
4.75
7.0
ICE3A1065
ICE3B1065
ICE3A1565
ICE3B1565
11.63
21
ICE3A2065
ICE3B2065
ICE3A2565
ICE3B2565
29.3
t.b.d
Effective output
capacitance,
energy related
ICE3A3065I
ICE3A3065P
ICE3B3065I
ICE3B3065P
VDS = 0V to 480V
ICE3A4065I
ICE3A4065P
ICE3B4065I
ICE3B4065P
Co(er)8
Co(er)9
Co(er)10
Co(er)11
-
-
-
-
t.b.d
t.b.d
t.b.d
t.b.d
-
-
-
-
pF
pF
pF
pF
ICE3A4565I
ICE3A4565P
ICE3B4565I
ICE3B4565P
ICE3A6065I
ICE3A6065P
ICE3B6065I
ICE3B6065P
ICE3A6565I
ICE3A6565P
ICE3B6565I
ICE3B6565P
Rise Time
Fall Time
1)
trise
tfall
-
-
301)
301)
-
-
ns
ns
Measured in a Typical Flyback Converter Application
Preliminary Datasheet V1.2
25
21 May 2004
CoolSET™-F3
Preliminary Data
Outline Dimension
5
Outline Dimension
PG-DIP-8-6
(Leadfree Plastic Dual In-
Line Outline)
Figure 20 PG-DIP-8-6 (Leadfree Plastic Dual In-Line Outline)
9.9
4.4
P-TO220-6-46
(Isodrain I2Pak Package)
A
+0.1
7.5
1.3
-0.02
6.6
B
0.05
1)
7.62
±0.1
0.5
M
0.25
A B
0...0.15
2.4
±0.1
6 x 0.6
±0.3
5.3
4 x 1.27
±0.3
8.4
1) Shear and punch direction no burrs this surface
Back side, heatsink contour
All metal surfaces tin plated, except area of cut.
Figure 21 P-TO220-6-46 (Isodrain I2Pak Package)
Preliminary Datasheet V1.2
26
21 May 2004
CoolSET™-F3
Preliminary Data
Outline Dimension
±0.2
9.9
P-TO220-6-47
(Isodrain Package)
A
±0.2
9.5
4.4
+0.1
7.5
6.6
1.3
-0.02
B
0.05
1)
7.62
0.25
±0.1
0.5
M
A B
0...0.15
2.4
±0.1
6 x 0.6
±0.3
5.3
4 x 1.27
±0.3
8.4
1) Shear and punch direction no burrs this surface
Back side, heatsink contour
All metal surfaces tin plated, except area of cut.
Figure 22 P-TO220-6-47 (Isodrain Package)
Dimensions in mm
Preliminary Datasheet V1.2
27
21 May 2004
Total Quality Management
Qualität hat für uns eine umfassende
Bedeutung. Wir wollen allen Ihren
Ansprüchen in der bestmöglichen
Weise gerecht werden. Es geht uns also
nicht nur um die Produktqualität –
unsere Anstrengungen gelten
gleichermaßen der Lieferqualität und
Logistik, dem Service und Support
sowie allen sonstigen Beratungs- und
Betreuungsleistungen.
Quality takes on an allencompassing
significance at Semiconductor Group.
For us it means living up to each and
every one of your demands in the best
possible way. So we are not only
concerned with product quality. We
direct our efforts equally at quality of
supply and logistics, service and
support, as well as all the other ways in
which we advise and attend to you.
Dazu gehört eine bestimmte
Part of this is the very special attitude of
our staff. Total Quality in thought and
deed, towards co-workers, suppliers
and you, our customer. Our guideline is
“do everything with zero defects”, in an
open manner that is demonstrated
beyond your immediate workplace, and
to constantly improve.
Geisteshaltung unserer Mitarbeiter.
Total Quality im Denken und Handeln
gegenüber Kollegen, Lieferanten und
Ihnen, unserem Kunden. Unsere
Leitlinie ist jede Aufgabe mit „Null
Fehlern“ zu lösen – in offener
Sichtweise auch über den eigenen
Arbeitsplatz hinaus – und uns ständig
zu verbessern.
Throughout the corporation we also
think in terms of Time Optimized
Processes (top), greater speed on our
part to give you that decisive
competitive edge.
Unternehmensweit orientieren wir uns
dabei auch an „top“ (Time Optimized
Processes), um Ihnen durch größere
Schnelligkeit den entscheidenden
Wettbewerbsvorsprung zu verschaffen.
Give us the chance to prove the best of
performance through the best of quality
– you will be convinced.
Geben Sie uns die Chance, hohe
Leistung durch umfassende Qualität zu
beweisen.
Wir werden Sie überzeugen.
h t t p : / / w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG
相关型号:
ICE3A4565P
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD
INFINEON
ICE3A5565I
SWITCHING REGULATOR, 100kHz SWITCHING FREQ-MAX, ZIP6, ROHS COMPLIANT, TO-220, 6 LEAD
ROCHESTER
ICE3A5565PBKSA1
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, ROHS COMPLIANT, TO-220, 6 LEAD
INFINEON
ICE3A6065I
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD
INFINEON
ICE3A6065P
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD
INFINEON
ICE3A6565I
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD
INFINEON
ICE3A6565P
Switching Regulator, Current-mode, 100kHz Switching Freq-Max, PZFM6, TO-220, 6 LEAD
INFINEON
ICE3AR0680JZ
Switching Controller, Current-mode, 113kHz Switching Freq-Max, BICMOS, PDIP7, GREEN, PLASTIC, DIP-7
INFINEON
©2020 ICPDF网 联系我们和版权申明