IKCM15H60HA_15 [INFINEON]
Control Integrated POwer System;型号: | IKCM15H60HA_15 |
厂家: | Infineon |
描述: | Control Integrated POwer System |
文件: | 总16页 (文件大小:953K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Control Integrated POwer
System (CIPOS™)
IKCM15H60HA
Datasheet
For Power Management Application
1
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Table of Contents
CIPOS™ Control Integrated POwer System ........................................................................................................3
Features..............................................................................................................................................................3
Target Applications...........................................................................................................................................3
Description.........................................................................................................................................................3
System Configuration .......................................................................................................................................3
Pin Configuration....................................................................................................................................................4
Internal Electrical Schematic.................................................................................................................................4
Pin Assignment.......................................................................................................................................................5
Pin Description ..................................................................................................................................................5
HIN(U,V,W) and LIN(U,V,W) (Low side and high side control pins, Pin 7 - 12)................................................5
VFO (Fault-output, Pin 14) ................................................................................................................................6
ITRIP (Over current detection function, Pin 15) ................................................................................................6
VDD, VSS (Low side control supply and reference, Pin 13, 16).......................................................................6
VB(U,V,W) and VS(U,V,W) (High side supplies, Pin 1 - 6)...............................................................................6
NW, NV, NU (Low side emitter, Pin 17 - 19).....................................................................................................6
W, V, U (High side emitter and low side collector, Pin 20 - 22) ........................................................................6
P (Positive bus input voltage, Pin 23)................................................................................................................6
Absolute Maximum Ratings...................................................................................................................................7
Module Section..................................................................................................................................................7
Inverter Section..................................................................................................................................................7
Control Section..................................................................................................................................................7
Recommended Operation Conditions..................................................................................................................8
Static Parameters ...................................................................................................................................................9
Dynamic Parameters ............................................................................................................................................10
Bootstrap Parameters ..........................................................................................................................................10
Mechanical Characteristics and Ratings............................................................................................................11
Circuit of a Typical Application...........................................................................................................................12
Switching Times Definition..................................................................................................................................12
Electrical characteristic .......................................................................................................................................13
Package Outline....................................................................................................................................................14
Datasheet
2
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
CIPOS™
Control Integrated POwer System
Dual In-Line Intelligent Power Module
3Φ-bridge 600V / 15A
Features
Description
Fully isolated Dual In-Line molded module
TrenchStop® IGBTs
The CIPOS™ module family offers the chance for
integrating various power and control components
to increase reliability, optimize PCB size and system
costs.
Rugged SOI gate driver technology with stability
against transient and negative voltage
Allowable negative VS potential up to -11V for
signal transmission at VBS=15V
It is designed to control three phase AC motors and
permanent magnet motors in variable speed drives
for applications like a washing machine. The
package concept is specially adapted to power
applications, which need good thermal conduction
and electrical isolation, but also EMI-save control
and overload protection.
Integrated bootstrap functionality
Over current shutdown
Under-voltage lockout at all channels
Low side emitter pins accessible for all phase
current monitoring (open emitter)
TrenchStop® IGBTs and anti parallel diodes are
combined with an optimized SOI gate driver for
excellent electrical performance.
Cross-conduction prevention
All of 6 switches turn off during protection
Lead-free terminal plating; RoHS compliant
System Configuration
3 half bridges with TrenchStop® IGBTs and anti
parallel diodes
Target Applications
Washing machines
Fans
3Φ SOI gate driver
Pin-to-heasink creepage distance typ. 1.6mm
Low power motor drives
Datasheet
3
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Pin Configuration
Bottom View
Figure 1: Pin configuration
Internal Electrical Schematic
Figure 2: Internal schematic
Datasheet
4
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Pin Assignment
Pin Number Pin Name
Pin Description
1
VS(U)
VB(U)
VS(V)
VB(V)
VS(W)
VB(W)
HIN(U)
HIN(V)
HIN(W)
LIN(U)
LIN(V)
LIN(W)
VDD
VFO
ITRIP
VSS
U-phase high side floating IC supply offset voltage
U-phase high side floating IC supply voltage
V-phase high side floating IC supply offset voltage
V-phase high side floating IC supply voltage
W-phase high side floating IC supply offset voltage
W-phase high side floating IC supply voltage
U-phase high side gate driver input
V-phase high side gate driver input
W-phase high side gate driver input
U-phase low side gate driver input
V-phase low side gate driver input
W-phase low side gate driver input
Low side control supply
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Fault output
Over current shutdown input
Low side control negative supply
W-phase low side emitter
NW
NV
V-phase low side emitter
NU
U-phase low side emitter
W
Motor W-phase output
V
Motor V-phase output
U
Motor U-phase output
P
Positive bus input voltage
NC
No Connection
Pin Description
HIN(U,V,W) and LIN(U,V,W) (Low side and high
side control pins, Pin 7 - 12)
5k
These pins are positive logic and they are
responsible for the control of the integrated IGBT.
The Schmitt-trigger input thresholds of them are
such to guarantee LSTTL and CMOS compatibility
down to 3.3V controller outputs. Pull-down resistor
of about 5k is internally provided to pre-bias inputs
during supply start-up and a zener clamp is
provided for pin protection purposes. Input Schmitt-
trigger and noise filter provide beneficial noise
rejection to short input pulses.
Figure 3: Input pin structure
The noise filter suppresses control pulses which are
below the filter time tFILIN. The filter acts according to
Figure 4.
Figure 4: Input filter timing diagram
Datasheet
5
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
It is recommended for proper work of CIPOS™ not
to provide input pulse-width lower than 1us.
VDD, VSS (Low side control supply and
reference, Pin 13, 16)
The integrated gate drive provides additionally a
shoot through prevention capability which avoids
the simultaneous on-state of two gate drivers of the
same leg (i.e. HO1 and LO1, HO2 and LO2, HO3
and LO3). When two inputs of a same leg are
activated, only former activated one is activated so
that the leg is kept steadily in a safe state.
VDD is the low side supply and it provides power
both to input logic and to low side output power
stage. Input logic is referenced to VSS ground.
The under-voltage circuit enables the device to
operate at power on when a supply voltage of at
least a typical voltage of VDDUV+ = 12.1V is present.
The IC shuts down all the gate drivers’ power
outputs, when the VDD supply voltage is below
VDDUV- = 10.4V. This prevents the external power
switches from critically low gate voltage levels
during on-state and therefore from excessive power
dissipation.
A minimum deadtime insertion of typically 380ns is
also provided by driver IC, in order to reduce cross-
conduction of the external power switches.
VFO (Fault-output, Pin 14)
The VFO pin indicates a module failure in case of
under voltage at pin VDD or in case of triggered
over current detection at ITRIP.
VB(U,V,W) and VS(U,V,W) (High side supplies,
Pin 1 - 6)
VB to VS is the high side supply voltage. The high
side circuit can float with respect to VSS following
the external high side power device emitter voltage.
VDD
RON,FLT
>1
VFO
VSS
from ITRIP -Latch
Due to the low power consumption, the floating
driver stage is supplied by integrated bootstrap
circuit.
from uv-detection
CIPOS™
The under-voltage detection operates with a rising
supply threshold of typical VBSUV+ = 12.1V and a
falling threshold of VBSUV- = 10.4V.
Figure 5: Internal circuit at pin VFO
VS(U,V,W) provide a high robustness against
negative voltage in respect of VSS of -50V
transiently. This ensures very stable designs even
under rough conditions.
ITRIP (Over current detection function, Pin 15)
CIPOS™ provides an over current detection
function by connecting the ITRIP input with the
motor current feedback. The ITRIP comparator
threshold (typ. 0.47V) is referenced to VSS ground.
An input noise filter (typ: tITRIPMIN = 530ns) prevents
the driver to detect false over-current events.
NW, NV, NU (Low side emitter, Pin 17 - 19)
The low side emitters are available for current
measurements of each phase leg. It is
recommended to keep the connection to pin VSS as
short as possible in order to avoid unnecessary
inductive voltage drops.
Over current detection generates a shut down of all
outputs of the gate driver after the shutdown
propagation delay of typically 1000ns.
W, V, U (High side emitter and low side collector,
Pin 20 - 22)
The fault-clear time is set to typical 65us.
These pins are motor U, V, W input pins
P (Positive bus input voltage, Pin 23)
The high side IGBT are connected to the bus
voltage. It is Snoted that the bus voltage does not
exceed 450 V.
Datasheet
6
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Absolute Maximum Ratings
(VDD = 15V and TJ = 25°C, if not stated otherwise)
Module Section
Value
Description
Condition
Symbol
Unit
min
-40
max
125
-
Storage temperature range
Insulation test voltage
°C
V
Tstg
VISOL
TC
RMS, f = 60Hz, t =1min
Refer to Figure 6
2000
-40
Operating case temperature range
100
°C
Inverter Section
Description
Value
Condition
Symbol
Unit
min
max
-
Max. blocking voltage
IC=250µA
VCES
VPN
600
V
V
V
DC link supply voltage of P-N
DC link supply voltage (surge) of P-N
Applied between P-N
Applied between P-N
-
-
450
500
VPN(surge)
TC = 25°C, TJ < 150°C
TC = 80°C, TJ < 150°C
-15
-10
15
10
Output current
IC
A
Maximum peak output current
Short circuit withstand time1
less than 1ms
IC
tSC
Ptot
TJ
-24
-
24
5
A
µs
W
°C
VDC ≤400V, TJ = 150°C
Power dissipation per IGBT
-
25.2
150
Operating junction temperature range
-40
Single IGBT thermal resistance,
junction-case
4.96
5.41
K/W
K/W
RthJC
-
-
Single diode thermal resistance,
junction-case
RthJCD
Control Section
Value
Description
Condition
Symbol
Unit
min
max
Module supply voltage
VDD
VBS
-1
20
V
V
High side floating supply voltage
(VB vs. VS)
-1
20
VIN
VITRIP
-1
-1
10
10
Input voltage
LIN, HIN, ITRIP
V
Switching frequency
fPWM
-
20
kHz
1 Allowed number of short circuits: <1000; time between short circuits: >1s.
Datasheet
7
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Recommended Operation Conditions
All voltages are absolute voltages referenced to VSS -potential unless otherwise specified.
Value
Description
DC link supply voltage of P-N
Symbol
Unit
min
0
typ
-
max
450
VPN
VBS
VDD
V
V
V
High side floating supply voltage (VB vs. VS)
Low side supply voltage
13.5
14.5
-
18.5
18.5
16
ΔVBS,
ΔVDD
-1
-1
1
1
Control supply variation
-
V/µs
VIN
VITRIP
0
0
5
5
Logic input voltages LIN,HIN,ITRIP
Between VSS - N (including surge)
-
-
V
V
VSS
-5
5
Figure 6: TC measurement point2
2Any measurement except for the specified point in figure 6 is not relevant for the temperature verification and
brings wrong or different information.
Datasheet
8
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Static Parameters
(VDD = 15V and TJ = 25°C, if not stated otherwise)
Value
typ
Description
Condition
Symbol
Unit
min
max
Iout = 10A
-
-
1.9
2.4
2.8
-
Collector-Emitter saturation voltage
VCE(sat)
V
TJ = 25°C
150°C
Iout = -10A
-
-
1.75
1.8
2.4
Emitter-Collector forward voltage
VF
V
TJ = 25°C
150°C
Collector-Emitter leakage current
Logic "1" input voltage (LIN,HIN)
Logic "0" input voltage (LIN,HIN)
ITRIP positive going threshold
ITRIP input hysteresis
VCE = 600V
ICES
VIH
-
-
-
1
2.5
-
mA
V
2.1
0.9
470
70
VIL
0.7
400
40
V
VIT,TH+
VIT,HYS
540
-
mV
mV
VDD and VBS supply under voltage
positive going threshold
VDDUV+
VBSUV+
10.8
9.5
1.0
9.0
-
12.1
10.4
1.7
13.0
11.2
-
V
V
VDD and VBS supply under voltage
negative going threshold
VDDUV-
VBSUV-
VDD and VBS supply under voltage
lockout hysteresis
VDDUVH
VBSUVH
V
Input clamp voltage
(HIN, LIN, ITRIP)
Iin = 4mA
VINCLAMP
10.1
300
370
12.5
500
900
V
Quiescent VBx supply current
(VBx only)
HIN = 0V
IQBS
µA
µA
Quiescent VDD supply current
(VDD only)
LIN = 0V, HINX = 5V
IQDD
IIN+
-
Input bias current
VIN = 5V
-
-
-
-
-
1
2
1.5
mA
µA
µA
nA
V
Input bias current
VIN = 0V
-
IIN-
IITRIP+
IFO
ITRIP input bias current
VFO input bias current
VFO output voltage
VITRIP = 5V
65
2
150
VFO = 5V, VITRIP = 0V
IFO = 10mA, VITRIP = 1V
-
-
VFO
0.5
Datasheet
9
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Dynamic Parameters
(VDD = 15V and TJ = 25°C, if not stated otherwise)
Value
typ
610
30
Description
Condition
Symbol
Unit
min
max
Turn-on propagation delay time
Turn-on rise time
ton
tr
-
-
-
-
ns
ns
ns
ns
ns
ns
ns
ns
ns
VLIN,HIN = 5V; Iout = 10A,
VDC = 300V
Turn-on switching time
Reverse recovery time
Turn-off propagation delay time
Turn-off fall time
tc(on)
trr
100
115
790
65
toff
-
-
-
-
V
V
LIN,HIN = 0V; Iout = 10A,
DC = 300V
tf
Turn-off switching time
Short circuit propagation delay time
Input filter time ITRIP
tc(off)
tSCP
tITRIPmin
115
1440
530
From VIT,TH+ to 10% ISC
VITRIP = 1V
-
-
Input filter time at LIN, HIN for turn
on and off
V
LIN,HIN = 0V & 5V
tFILIN
tFLTCLR
DTPWM
DTIC
290
65
-
-
200
-
ns
µs
µs
ns
Fault clear time after ITRIP-fault
VITRIP = 1V
40
Deadtime between low side and high
side
0.5
Deadtime of gate drive circuit
380
VDC = 300V, IC = 10A,
TJ = 25°C
IGBT turn-on energy (includes
reverse recovery of diode)
-
-
235
340
-
-
Eon
Eoff
Erec
µJ
µJ
µJ
150°C
VDC = 300V, IC = 10A,
TJ = 25°C
-
-
150
220
-
-
IGBT turn-off energy
150°C
VDC = 300V, IC = 10A,
TJ = 25°C
-
-
30
60
-
-
Diode recovery energy
150°C
Bootstrap Parameters
(TJ = 25°C, if not stated otherwise)
Value
Description
Condition
Symbol
Unit
min
typ
max
Repetitive peak reverse
voltage
VRRM
600
V
VS2 or VS3 = 300V, TJ = 25°C
VS2 and VS3 = 0V, TJ = 25°C
VS2 or VS3 = 300V, TJ = 125°C
VS2 and VS3 = 0V, TJ = 125°C
35
40
50
65
Bootstrap resistance of
U-phase1
RBS1
Reverse recovery time
Forward voltage drop
IF= 0.6A, di/dt = 80A/µs
trr_BS
50
ns
V
VF_BS
IF= 20mA, VS2 and VS3 = 0V
2.6
1 RBS2 and RBS3 have same values to RBS1
.
Datasheet
10
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Mechanical Characteristics and Ratings
Value
typ
0.69
-
Unit
Description
Mounting torque
Condition
min
0.59
-50
-
max
0.78
100
-
M3 screw and washer
Refer to Figure 7
Nm
µm
g
Flatness
Weight
6.15
Figure 7: Flatness measurement position
Datasheet
11
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Circuit of a Typical Application
Figure 8: Application circuit
Switching Times Definition
Figure 9: Switching times definition
Datasheet
12
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Electrical characteristic
24
24
22
20
18
16
14
12
10
8
24
22
20
18
16
14
12
10
8
VDD=15V
TJ=25℃
22
20
18
16
14
12
TJ=25℃
10
VDD=15V
VDD=20V
TJ=150℃
8
6
4
2
0
TJ=25℃
6
6
TJ=150℃
4
4
2
2
0
0
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
0.5
1.0
1.5
2.0
2.5
3.0
VCE(sat), Collector - Emitter voltage [V]
VCE(sat), Collector - Emitter voltage [V]
V , Emitter - Collector voltage [V]
F
Typ. Collector – Emitter saturation voltage
Typ. Collector – Emitter saturation voltage
Typ. Emitter – Collector forward voltage
2.4
0.6
250
VDC=300V
VDD=15V
VDC=300V
2.2
High side @TJ=25℃
225
200
175
150
125
100
75
VDD=15V
High side @TJ=150℃
2.0
1.8
0.5
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
High side @TJ=25℃
1.6
0.4
High side @TJ=150℃
1.4
Low side @TJ=25℃
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.3
0.2
0.1
Low side @TJ=150℃
50
VDC=300V
VDD=15V
25
0.0
0
0
2
4
6
8
10 12 14 16 18 20 22 24
0
2
4
6
8
10 12 14 16 18 20 22 24
0
2
4
6
8
10 12 14 16 18 20 22 24
Ic, Collector current [A]
Ic, Collector current [A]
Ic, Collector current [A]
Typ. Turn on switching energy loss
Typ. Turn off switching energy loss
Typ. Reverse recovery energy loss
800
500
1200
VDC=300V
VDD=15V
VDC=300V
VDD=15V
VDC=300V
VDD=15V
1150
1100
1050
1000
950
450
400
350
300
250
200
150
100
50
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
750
700
650
600
550
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
900
850
800
750
700
650
0
600
0
2
4
6
8
10 12 14 16 18 20 22 24
0
2
4
6
8
10 12 14 16 18 20 22 24
0
2
4
6
8
10 12 14 16 18 20 22 24
Ic, Collector current [A]
Ic, Collector current [A]
Ic, Collector current [A]
Typ. Turn on propagation delay time
Typ. Turn on switching time
Typ. Turn off propagation delay time
10
350
350
325
300
275
250
225
200
175
150
125
100
75
VDC=300V
VDD=15V
VDC=300V
VDD=15V
325
300
275
250
225
200
175
150
125
100
75
1
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
High side @TJ=25℃
High side @TJ=150℃
Low side @TJ=25℃
Low side @TJ=150℃
0.1
D : duty ratio
D=50%
D=20%
D=10%
D=5%
D=2%
0.01
Single pulse
1E-3
1E-4
50
25
50
0
0
2
4
6
8
10 12 14 16 18 20 22 24
0
2
4
6
8
10 12 14 16 18 20 22 24
1E-7 1E-6 1E-5 1E-4 1E-3 0.01
0.1
1
10
100
t
, Pulse w idth [sec.]
Ic, Collector current [A]
Ic, Collector current [A]
P
Typ. Turn off switching time
Typ. Reverse recovery time
IGBT transient thermal resistance at all six
IGBTs operation
Datasheet
13
Ver. 1.2, 2014-06-01
CIPOS™ IKCM15H60HA
Package Outline
Datasheet
14
Ver. 1.2, 2014-06-01
CIPOS™ IGCM10F60HA
Revision History
Previous Version:
Datasheet Ver. 1.1
Major changes since the last revision
Page or Reference
Description of change
Figure 6 updated
8
14
Package Outline updated
Datasheet
15
Ver. 1.2, 2014-06-01
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolGaN™, CoolMOS™, CoolSET™, CoolSiC™, CORECONTROL™, CROSSAVE™, DAVE™,
DI-POL™, DrBLADE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™,
HybridPACK™, ISOFACE™, IsoPACK™, i-Wafer™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OPTIGA™, OptiMOS™, ORIGA™,
POWERCODE™, PRIMARION™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, ReverSave™, SatRIC™, SIEGET™,
SIPMOS™, SmartLEWIS™, SOLID FLASH™, SPOC™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™, PRIMECELL™, REALVIEW™, THUMB™, µVision™
of ARM Limited, UK. ANSI™ of American National Standards Institute. AUTOSAR™ of AUTOSAR development partnership. Bluetooth™ of Bluetooth
SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of
Epcos AG. FLEXGO™ of Microsoft Corporation. HYPERTERMINAL™ of Hilgraeve Incorporated. MCS™ of Intel Corp. IEC™ of Commission
Electrotechnique Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics
Corporation. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE
OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of OmniVision Technologies, Inc. Openwave™ of Openwave Systems Inc. RED HAT™
of Red Hat, Inc. RFMD™ of RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of
Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of
Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design
Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex.
Last Trademarks Update 2014-07-17
IMPORTANT NOTICE
For further information on the product, technology, delivery terms
and conditions and prices please contact your nearest Infineon
Technologies office (www.infineon.com).
www.Infineon.com
The information given in this document shall in no event be
regarded as
a guarantee of conditions or characteristics
Edition 2014-06-01
(“Beschaffenheitsgarantie”). With respect to any examples, hints
or any typical values stated herein and/or any information
regarding the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities of any kind,
including without limitation warranties of non-infringement of
intellectual property rights of any third party.
Published by
WARNINGS
Infineon Technologies AG
81726 München, Germany
Due to technical requirements products may contain dangerous
substances. For information on the types in question please
contact your nearest Infineon Technologies office.
© Infineon Technologies AG 2015.
All Rights Reserved.
Except as otherwise explicitly approved by Infineon Technologies
In addition, any information given in this document is subject to
customer’s compliance with its obligations stated in this document
and any applicable legal requirements, norms and standards
concerning customer’s products and any use of the product of
Infineon Technologies in customer’s applications.
in a written document signed by authorized representatives of
Infineon Technologies, Infineon Technologies’ products may not be
used in any applications where a failure of the product or any
consequences of the use thereof can reasonably be expected to
result in personal injury.
The data contained in this document is exclusively intended for
technically trained staff. It is the responsibility of customer’s
technical departments to evaluate the suitability of the product for
the intended application and the completeness of the product
information given in this document with respect to such
application.
相关型号:
©2020 ICPDF网 联系我们和版权申明