IRIS4007PBF [INFINEON]
Switching Regulator, Current-mode, 20A, PSFM5, TO-220, 5 PIN;型号: | IRIS4007PBF |
厂家: | Infineon |
描述: | Switching Regulator, Current-mode, 20A, PSFM5, TO-220, 5 PIN 局域网 开关 |
文件: | 总6页 (文件大小:61K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Data Sheet No. PD60183-C
( )
IRIS4007 K
INTEGRATED SWITCHER
Features
• Primary current mode control, and secondary
voltage mode control
Packages
•
•
Vcc over-voltage protection (latched)
Over-current and over-temperature protection
• Quasi resonant, variable frequency operation
•
•
•
5 pinTO-220 andTO-262 package
0.4Ω Rds(on) max/ 200V MOSFET
Fully Characterized Avalanche Energy
IRIS4007
IRIS4007K
5 LeadTO-220
5 LeadTO-262
Descriptions
The IRIS4007(K) is a dual mode voltage and current controller combined with a MOSFET in a single Package.
The IRIS4007(K) are designed for use in AC/DC and DC/DC switching power supplies upto 100VDC nominal
input and is capable of 30W for a nominal 48V input.The device can operate in either a quasi-resonant or Pulse
Ratio Control (PRC) mode, and thereby variable frequency operation.
Typical Connection Diagram
Vin
(AC/
DC)
Vout
(DC)
3
Drain
4
5
Vcc
IRIS4007(K)
FB
Gnd
Source
1
2
(Refer to Lead Assignments for correct pin
configuration). This/These diagram(s) show electrical
connections only. Please refer to our DesignTips
and Application Notes (AN1018a, AN1024a,
AN1025) for proper circuit board layout.
www.irf.com
1
( )
IRIS4007 K
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are
absolute voltages referenced to terminals stated, all currents are defined positive into any lead.The thermal resistance and
power dissipation ratings are measured under board mounted and still air conditions.
Symbol Definition
Terminals Max. Ratings Units
Note
IDpeak
IDmax
Peak drain current
3-1
3-1
20
Single pulse
Maximum switching current
4.0
A
V
= 0.78V
2-3
Tc=25oC
EAS
Single pulse avalanche energy
3-1
350
mJ
V
=50V,L=10mH,
dd
Tc=25oC
VCC
VTH
Power supply voltage
4-3
5-2
35
6
V
OCP/FB terminal voltage
Power dissipation for MOSFET
P
73
With infinite heatsink
Without heatsink
D1
3-1
W
1.27
0.8
P
Power dissipation for control part (MIC)
Thermal resistance, junction to case
Junction temperature
4-2
—
—
—
—
Specified by VIN x IIN
D2
Rth
1.7
°C/W
JC
T
T
T
-40-125
-40-125
-20-125
J
Storage temperature
S
Internal frame temperature in operation
Refertorecommended
operating temperature
°C
f
T
Ambient operating temperature
—
—
-20-125
300
OP
L
T
Lead temp. (soldering, 10 seconds)
Recommended Operating Conditions
Time for input of quasi resonant signals.
Tth(2)≥1.0µs
For the Quasi resonant signal inputted to the VDCP/FB
terminal at the time of quasi resonant operation, the
signal should be wider thantTth(2)
VOCP/FB
Vth(2)
www.irf.com
2
( )
IRIS4007 K
Electrical Characteristics (for Control IC)
V
CC
= 18V, (T = 25°C) unless otherwise specified.
A
Symbol
VCCUV+
VCCUV-
IQCCUV
IQCC
Definition
Min. Typ. Max. Units Test Conditions
VCC supply undervoltage positive going threshold
VCC supply undervoltage negative going threshold
UVLO mode quiescent current
14.4
9
16
10
17.6
11
V
—
—
100
30
µA
VCC < VCCUV+
Quiescent operating VCC supply current
—
—
mA
TOFF/(MAX) Maximum OFF time
40
—
60
µsec
TTH(2)
TOFF/(MIN)
VTH(1)
Minimum input pulse width for quasi resonant signals
—
—
1.0
1.5
0.78
1.6
1.7
24.5
400
8.4
—
Minimum OFF time
—
—
OCP/FB terminal threshold voltage 1
OCP/FB terminal threshold voltage 2
OCP/FB terminal sink current
VCC overvoltage protection limit
Latch circuit holding current
0.68
1.3
1.1
20.5
—
0.73
1.45
1.35
22.5
—
V
VTH(2)
IOCP/FB
VCC(OVP)
ICC(LA)
mA
V
µA
V
oC
VCC(LaOFF) Latch circuit reset voltage
6.6
140
—
TJ(TSD)
Thermal shutdown activation temperature
—
Electrical Characteristics (for MOSFET)
(T = 25°C) unless otherwise specified.
A
Symbol
VDSS
Definition
Drain-to-source breakdown voltage
Drain leakage current
Min. Typ. Max. Units Test Conditions
200
—
—
—
V
IDSS
—
250
µA
Vds=160V,VCC=0V
Tj =125oC
RDS(ON)
On-resistance
—
—
0.4
Ω
V3-1=10V, ID=4A
t
Rise time (10% to 90%)
Thermal resistance
—
—
—
—
200
1.7
ns
oC/W
r
Between junction
and case
THj-C
www.irf.com
3
( )
IRIS4007 K
Block Diagram
4
Vcc
3
D
START
REG.
O.V.P
LATCH
DRIVE
1
S
-
Vth(1)
OSCILLATOR
T.S.D
+
5
Comp.1
OCP/
FB
-
Vth(2)
+
Comp.2
2
Ground
Pin # Symbol
Description
Lead Assignments
1
2
3
4
S
Ground
D
MOSFET Source terminal
Ground terminal
MOSFET Drain terminal
Control circuit supply voltage
Vcc
1
2
3
4
5
Overcurrent detection, and Voltage mode control
feedback signal
5
OCP/FB
Other Functions
O.V.P. – Overvoltage Protection Circuit
T.S.D. – Thermal Shutdown Circuit
www.irf.com
4
( )
IRIS4007 K
Case outline
01-6020 00
01-3042 01 (TS-001)
5-Lead TO-220
www.irf.com
5
( )
IRIS4007 K
Case outline
B
4.83 [.190]
4.06 [.160]
10.29 [.405]
1.40 [.055]
9.65 [.380]
MAX.
6.22[.245]
MIN
1.32 [.052]
1.22 [.048]
6
8.00[.315]
MAX
9.65 [.380]
8.64 [.340]
6
1 2
3 4 5
C
12.70 [.500]
14.73 [.580]
0.63 [.025]
0.31 [.012]
1.01[.040]
0.51[.020]
5X
5X
2.92 [.115]
2.16 [.085]
1.70 [.067]
4X
0.25 [.010]
A
B
5-Lead TO-262
IR WORLD HEADQUARTERS: 233 Kansas Street, El Segundo, California 90245 Tel: (310) 252-7105
Data and specifications subject to change without notice. 10/17/2001
www.irf.com
6
相关型号:
©2020 ICPDF网 联系我们和版权申明